Search NASA⌕ Search

SEARCH · Search NASA

Results for “high dependability computing program”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Cr plasma-material-interaction in PISCES-RF: D thermal release, retention, and erosion

Pure chromium (Cr) targets were exposed to high-flux deuterium (D) plasmas in the Pisces-RF linear plasma device, and measurements of D retention, release, and erosion were subsequently performed. Post-exposure D retention was quantified using temperature-programmed desorption on Cr targets irradiated by 50 eV ions over a broad range of exposure temperatures (423–873 K) and ion fluences (3 × 10 24 – 3 × 10 26 m −2 ). The retained D inventory was observed to decrease rapidly with increased exposure temperature, from approximately ∼7 × 10 20 m −2 at ∼ 420 K, to then saturate near ∼ 10 20 m −2 for exposure temperatures above ∼550 K. Separately, at fixed exposure temperature (∼450 K), D retention was found to have only a weak dependence on increasing ion fluence. Lastly, the erosion of Cr in D plasma was investigated for ion impact energies in the range 40 ≤ E i ≤ 250 eV. Erosion was inferred using optical emission spectroscopy (OES) from the ratio of emission lines (Cr I (425.4 nm)/D I (656.1 nm)) measured close to the target. Conversion of the OES yield data to net erosion yield was made with singular ion energy target mass-loss measurements. These net erosion yield data were then further corrected to obtain gross erosion yield by accounting for a re-deposition factor, computed using a simple model. The gross erosion yield is found to be 2–4 times lower than predicted by SDTrimSP, consistent with that typically observed for light-ion sputtering under high-flux plasma conditions.

Chromium↗
DOE OSTI2023

Computational Theory Applied to Nanostructures (Final Report)

Within the nanoscale, phenomena occur that are characteristic of neither the atomic limit, nor the macroscopic limit. In particular, properties that are intensive at the macroscopic scale become size dependent at the nanoscale. These phenomena can have direct consequence for understanding and characterizing materials used in electronic, optical, and micro-mechanical applications related to energy science and technologies. To capitalize properly on predicting and understanding such phenomena in this nano regime, a deeper understanding of the quantum properties of materials will be required. The objective of our research program was to advance the field in computational modeling, analysis and understanding of materials at the nano scale, both in terms of dimensionality and quantum confinement. We employed a multidisciplinary approach, drawing from physics, materials science, chemical engineering and computer science. This research will provide new knowledge, computational techniques, and provide high-potential links across all these disciplines. Over sixty papers were published during the period in question. Ten of the papers were published in high impact journals such as Nano Letters, Nature Communications and Physical Review Letters.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Scaling neural simulations in STACS

Abstract As modern neuroscience tools acquire more details about the brain, the need to move towards biological-scale neural simulations continues to grow. However, effective simulations at scale remain a challenge. Beyond just the tooling required to enable parallel execution, there is also the unique structure of the synaptic interconnectivity, which is globally sparse but has relatively high connection density and non-local interactions per neuron. There are also various practicalities to consider in high performance computing applications, such as the need for serializing neural networks to support potentially long-running simulations that require checkpoint-restart. Although acceleration on neuromorphic hardware is also a possibility, development in this space can be difficult as hardware support tends to vary between platforms and software support for larger scale models also tends to be limited. In this paper, we focus our attention on Simulation Tool for Asynchronous Cortical Streams (STACS), a spiking neural network simulator that leverages the Charm++ parallel programming framework, with the goal of supporting biological-scale simulations as well as interoperability between platforms. Central to these goals is the implementation of scalable data structures suitable for efficiently distributing a network across parallel partitions. Here, we discuss a straightforward extension of a parallel data format with a history of use in graph partitioners, which also serves as a portable intermediate representation for different neuromorphic backends. We perform scaling studies on the Summit supercomputer, examining the capabilities of STACS in terms of network build and storage, partitioning, and execution. We highlight how a suitably partitioned, spatially dependent synaptic structure introduces a communication workload well-suited to the multicast communication supported by Charm++. We evaluate the strong and weak scaling behavior for networks on the order of millions of neurons and billions of synapses, and show that STACS achieves competitive levels of parallel efficiency.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS1994

Technology Benefit Estimator (T/BEST): User's Manual

The Technology Benefit Estimator (T/BEST) system is a formal method to assess advanced technologies and quantify the benefit contributions for prioritization. T/BEST may be used to provide guidelines to identify and prioritize high payoff research areas, help manage research and limited resources, show the link between advanced concepts and the bottom line, i.e., accrued benefit and value, and to communicate credibly the benefits of research. The T/BEST software computer program is specifically designed to estimating benefits, and benefit sensitivities, of introducing new technologies into existing propulsion systems. Key engine cycle, structural, fluid, mission and cost analysis modules are used to provide a framework for interfacing with advanced technologies. An open-ended, modular approach is used to allow for modification and addition of both key and advanced technology modules. T/BEST has a hierarchical framework that yields varying levels of benefit estimation accuracy that are dependent on the degree of input detail available. This hierarchical feature permits rapid estimation of technology benefits even when the technology is at the conceptual stage. As knowledge of the technology details increases the accuracy of the benefit analysis increases. Included in T/BEST's framework are correlations developed from a statistical data base that is relied upon if there is insufficient information given in a particular area, e.g., fuel capacity or aircraft landing weight. Statistical predictions are not required if these data are specified in the mission requirements. The engine cycle, structural fluid, cost, noise, and emissions analyses interact with the default or user material and component libraries to yield estimates of specific global benefits: range, speed, thrust, capacity, component life, noise, emissions, specific fuel consumption, component and engine weights, pre-certification test, mission performance engine cost, direct operating cost, life cycle cost, manufacturing cost, development cost, risk, and development time. Currently, T/BEST operates on stand-alone or networked workstations, and uses a UNIX shell or script to control the operation of interfaced FORTRAN based analyses. T/BEST's interface structure works equally well with non-FORTRAN or mixed software analysis. This interface structure is designed to maintain the integrity of the expert's analyses by interfacing with expert's existing input and output files. Parameter input and output data (e.g., number of blades, hub diameters, etc.) are passed via T/BEST's neutral file, while copious data (e.g., finite element models, profiles, etc.) are passed via file pointers that point to the expert's analyses output files. In order to make the communications between the T/BEST's neutral file and attached analyses codes simple, only two software commands, PUT and GET, are required. This simplicity permits easy access to all input and output variables contained within the neutral file. Both public domain and proprietary analyses codes may be attached with a minimal amount of effort, while maintaining full data and analysis integrity, and security. T/BESt's sotware framework, status, beginner-to-expert operation, interface architecture, analysis module addition, and key analysis modules are discussed. Representative examples of T/BEST benefit analyses are shown.

Generazio, Edward R.↗
DOE OSTI2023

Incorporation of market signals for the optimal design of post combustion carbon capture systems

Recent studies have shown that fossil generators equipped with post-combustion carbon capture (PCC) systems are needed to reduce the cost of deep decarbonization. Such generators need to be flexible and responsive to grid conditions, particularly in a high variable renewable energy (VRE) environment. In this work, we evaluate the net present value (NPV) of retrofitting an existing natural gas combined cycle (NGCC) unit with a flexible PCC system while incorporating market signals from a high VRE grid. We use our industrial partner’s NGCC configuration as representative of existing NGCC units and Svante’s rapid-temperature swing adsorption (TSA) for PCC. Because of its ability to rapidly startup/shutdown and ramp-up/ramp-down, the chosen capture technology is very attractive for load-following operations. For a given set of market signals, we formulate a two-stage stochastic multi-period optimization problem, under the price-taker assumption, to simultaneously optimize the design of the capture system and operation of the entire plant. Rigorous models for the NGCC unit, PCC system, and compression system are developed using commercial process simulators and validated with either plant or vendor data. For computational tractability, we develop surrogate/reduced-order models for use in the optimization problem. The surrogate model for the NGCC plant is constructed by linearizing the rigorous dynamic model at 75% load, while data-driven nonlinear surrogate models for the capture and compression systems are constructed using simulation data from the rigorous models. The optimization problem, formulated as a mixed integer bilinear program, is implemented in the IDAES® integrated platform and solved to global optimality using Gurobi 9.5. Using this formulation, we determine the profitability of retrofitting an existing NGCC unit with the chosen capture system for multiple regions in the U.S. under two scenarios with different carbon prices. Importantly, the results show that the optimal decision strongly depends on the region and on the carbon price, thereby demonstrating the importance of the inclusion of market signals in the design process.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
NASA NTRS1980

Clarification process: Resolution of decision-problem conditions

A model of a general process which occurs in both decisionmaking and problem-solving tasks is presented. It is called the clarification model and is highly dependent on information flow. The model addresses the possible constraints of individual indifferences and experience in achieving success in resolving decision-problem conditions. As indicated, the application of the clarification process model is only necessary for certain classes of the basic decision-problem condition. With less complex decision problem conditions, certain phases of the model may be omitted. The model may be applied across a wide range of decision problem conditions. The model consists of two major components: (1) the five-phase prescriptive sequence (based on previous approaches to both concepts) and (2) the information manipulation function (which draws upon current ideas in the areas of information processing, computer programming, memory, and thinking). The two components are linked together to provide a structure that assists in understanding the process of resolving problems and making decisions.

Dieterly, D. L.↗
NASA NTRS2001

Discrete-State Simulated Annealing For Traveling-Wave Tube Slow-Wave Circuit Optimization

Algorithms based on the global optimization technique of simulated annealing (SA) have proven useful in designing traveling-wave tube (TWT) slow-wave circuits for high RF power efficiency. The characteristic of SA that enables it to determine a globally optimized solution is its ability to accept non-improving moves in a controlled manner. In the initial stages of the optimization, the algorithm moves freely through configuration space, accepting most of the proposed designs. This freedom of movement allows non-intuitive designs to be explored rather than restricting the optimization to local improvement upon the initial configuration. As the optimization proceeds, the rate of acceptance of non-improving moves is gradually reduced until the algorithm converges to the optimized solution. The rate at which the freedom of movement is decreased is known as the annealing or cooling schedule of the SA algorithm. The main disadvantage of SA is that there is not a rigorous theoretical foundation for determining the parameters of the cooling schedule. The choice of these parameters is highly problem dependent and the designer needs to experiment in order to determine values that will provide a good optimization in a reasonable amount of computational time. This experimentation can absorb a large amount of time especially when the algorithm is being applied to a new type of design. In order to eliminate this disadvantage, a variation of SA known as discrete-state simulated annealing (DSSA), was recently developed. DSSA provides the theoretical foundation for a generic cooling schedule which is problem independent, Results of similar quality to SA can be obtained, but without the extra computational time required to tune the cooling parameters. Two algorithm variations based on DSSA were developed and programmed into a Microsoft Excel spreadsheet graphical user interface (GUI) to the two-dimensional nonlinear multisignal helix traveling-wave amplifier analysis program TWA3. The algorithms were used to optimize the computed RF efficiency of a TWT by determining the phase velocity profile of the slow-wave circuit. The mathematical theory and computational details of the DSSA algorithms will be presented and results will be compared to those obtained with a SA algorithm.

Wilson, Jeffrey D.↗
NASA NTRS2022

Impact Simulation of Composite Panels for Aerospace Applications

The aerospace research community has been working towards the development of a comprehensive framework for the design of composite structures at the component, subassembly, assembly, and system levels. Such a framework requires accurate, efficient and easy-to-use mathematical and computational models that are in sync with physical reality. The research work in this paper is designed to help an aerospace structural engineer move towards this goal by simulating dynamic impact to composite panels. First, the existing orthotropic visco-elastic visco-plastic material model in LS-DYNA commercial finite element program, MAT_COMPOSITE_TABULATED_PLASTICITY_DAMAGE (MAT_213) is enhanced with the development and use of rate-dependent damage data. Using state-of-the-art experimental procedures, impact validation test data are created. Second, the versatility of the constitutive model is examined by its ability to simulate a low velocity (27 ft/s, 8 m/s) impact test, and two high velocity impact tests (385–417 ft/s, 117–127 m/s) that straddle the ballistic limit of the projectile and the composite panels. Third, these impact events are modeled using three different finite element types – under-integrated and fully-integrated solid elements, and fully-integrated thin shell elements. Insight into accuracy versus numerical efficiency is gained by comparing the performance of solid versus thin shell elements. The numerical results show that accurate predictions of these impact events can be obtained with reasonable effort and care.

Simulations↗
NASA NTRS2001

Publicly Available Numerical Codes for Modeling the X-ray and Microwave Emissions from Solar and Stellar Activity

We have posted numerical codes on the Web for modeling the bremsstrahlung x-ray emission and the a gyrosynchrotron radio emission from solar and stellar activity. In addition to radiation codes, steady-state and time-dependent Fokker-Planck codes are provided for computing the distribution and evolution of accelerated electrons. A 1-D hydrodynamics code computes the response of the stellar atmosphere (chromospheric evaporation). A code for modeling gamma-ray line spectra is also available. On-line documentation is provided for each code. These codes have been developed for modeling results from the High Energy Solar Spectroscopic Imager (HESSI) along related microwave observations of solar flares. Comprehensive codes for modeling images and spectra of solar flares are under development. The posted codes can be obtained on NASA/Goddard's HESSI Web Site at http://hesperia.gsfc.nasa.gov/hessi/modelware.htm. This work is supported in part by the NASA Sun-Earth Connection Program.

Holman, Gordon D.↗
DOE OSTI2025

Ceramography and Thermal Modelling of Irradiated TRISO Particles using BISON

This study presents a comprehensive analysis of irradiated TRISO fuel particles from the Advanced Gas Reactor (AGR) Fuel Development and Qualification Program conducted at the Advanced Test Reactor (ATR) as part of my internship. Failure Analysis using high-resolution microscopy was performed to characterize mechanisms in TRISO particle layers, including the kernel, buffer, inner pyrolytic carbon (IPyC), silicon carbide (SiC), and outer pyrolytic carbon (OPyC) coatings. Failure modes were systematically classified. Thermal conductivity properties of each TRISO layer were evaluated through experimental measurements and computational models for use in BISON finite element code. Experimental thermal conductivity values ranged from 0.5 W/m·K for the buffer layer to 168 W/m·K for SiC, while BISON simulations provided averaged values of 0.57 W/m·K (buffer), 4.0 W/m·K (PyC layers), and 15.95 W/m·K (SiC). Temperature-dependent correlations from PARFUME were implemented for kernel thermal properties.

BISON↗
DOE OSTI2022

ArQTiC: A Full-stack Software Package for Simulating Materials on Quantum Computers

ArQTiC is an open-source, full-stack software package built for the simulations of materials on quantum computers. It currently can simulate materials that can be modeled by any Hamiltonian derived from a generic, one-dimensional, time-dependent Heisenberg Hamiltonian. ArQTiC includes modules for generating quantum programs for real- and imaginary-time evolution, quantum circuit optimization, connection to various quantum backends via the cloud, and post-processing of quantum results. By enabling users to seamlessly design, execute, and analyze materials simulations on quantum computers, ArQTiC opens this field to a broader community of scientists from a wider range of scientific domains.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS2006

Thermal Model of a Current-Carrying Wire in a Vacuum

A computer program implements a thermal model of an insulated wire carrying electric current and surrounded by a vacuum. The model includes the effects of Joule heating, conduction of heat along the wire, and radiation of heat from the outer surface of the insulation on the wire. The model takes account of the temperature dependences of the thermal and electrical properties of the wire, the emissivity of the insulation, and the possibility that not only can temperature vary along the wire but, in addition, the ends of the wire can be thermally grounded at different temperatures. The resulting second-order differential equation for the steady-state temperature as a function of position along the wire is highly nonlinear. The wire is discretized along its length, and the equation is solved numerically by use of an iterative algorithm that utilizes a multidimensional version of the Newton-Raphson method.

Border, James↗
DOE OSTI2023

Coupling of CTF and RELAP5-3D Within an Enhanced Fidelity Nuclear Power Plant Simulator

A robust and accurate multiphysics engineering simulator is being developed to model the core behavior and system response of pressurized water reactors. This simulator relies on the NESTLE and CTF computer codes to model the neutronics and thermal hydraulics (TH), respectively, inside the core on a nodal scale and on the Reactor Excursion and Leak Analysis Program—Three Dimensional (RELAP5-3D) to model the entire nuclear steam supply system. The RELAP5-3D model includes highly detailed nodalization and multidimensional flow modeling throughout the vessel. Previously, pin-resolved data generated via the Virtual Environment for Reactor Analysis core simulator were used to improve the accuracy of the NESTLE core predictions. The engineering simulator being developed as part of this work uses the 3KEYMASTER platform to couple the enhanced NESTLE model to a nodal-fidelity CTF model to balance run time with accuracy; NESTLE provides node-dependent powers to CTF, and CTF provides node-dependent coolant densities and fuel temperatures to NESTLE.An overlapping domain approach is used for the core TH in which RELAP5-3D provides core boundary conditions based on the system response and CTF provides a node-dependent coolant heating rate to the RELAP5-3D core solution. In the preliminary TH demonstration discussed in this paper, CTF and RELAP5-3D provided similar steady-state core predictions, indicating the hydraulic compatibility between the codes, as well as reasonable and expected behavior under hypothetical transient conditions. This provides an initial step in ongoing efforts toward a robust, multiscale TH/neutronics engineering simulator capability.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
NASA NTRS1990

New correction procedures for the fast field program which extend its range

A fast field program (FFP) algorithm was developed based on the method of Lee et al., for the prediction of sound pressure level from low frequency, high intensity sources. In order to permit accurate predictions at distances greater than 2 km, new correction procedures have had to be included in the algorithm. Certain functions, whose Hankel transforms can be determined analytically, are subtracted from the depth dependent Green's function. The distance response is then obtained as the sum of these transforms and the Fast Fourier Transformation (FFT) of the residual k dependent function. One procedure, which permits the elimination of most complex exponentials, has allowed significant changes in the structure of the FFP algorithm, which has resulted in a substantial reduction in computation time.

West, M.↗
NASA NTRS1978

A comparison of the Method of Lines to finite difference techniques in solving time-dependent partial differential equations

Steady state solutions to two time dependent partial differential systems have been obtained by the Method of Lines (MOL) and compared to those obtained by efficient standard finite difference methods: (1) Burger's equation over a finite space domain by a forward time central space explicit method, and (2) the stream function - vorticity form of viscous incompressible fluid flow in a square cavity by an alternating direction implicit (ADI) method. The standard techniques were far more computationally efficient when applicable. In the second example, converged solutions at very high Reynolds numbers were obtained by MOL, whereas solution by ADI was either unattainable or impractical. With regard to 'set up' time, solution by MOL is an attractive alternative to techniques with complicated algorithms, as much of the programming difficulty is eliminated.

Kurtz, L. A.↗
NASA NTRS1989

Rarefied-continuum gas dynamics transition for SUMS project

This program is to develop an analytic method for reducing SUMS data for the determination of the undisturbed atmosphere conditions ahead of the shuttle along its descending trajectory. It is divided into an internal flow problem, an external flow problem and their matching conditions. Since the existing method of Direct Simulation Monte Carlo (DSMC) failed completely for the internal flow problem, the emphasis is on the internal flow of a highly non-equilibrium, rarefied air through a short tube of a diameter much less than the gaseous mean free path. A two fluid model analysis of this internal flow problem has been developed and studied with typical results illustrated. A computer program for such an analysis and a technical paper published in Lecture Notes in Physics No. 323 (1989) are included as Appendices 3 and 4. A proposal for in situ determination of the surface accommodation coefficients sigma sub t and sigma e is included in Appendix 5 because of their importance in quantitative data reduction. A two fluid formulation for the external flow problem is included as Appendix 6 and a review article for AIAA on Hypersonic propulsion, much dependent on ambient atmospheric density, is also included as Appendix 7.

Cheng, Sin-I↗
NASA NTRS2017

IDEAS Pamphlet for CES

Pamphlet on the IDEAS project for the Game Changing Development programs NASA booth at the Consumer Electronics Show. Pamphlet covers a high level overview of the technology developed and its capabilities. The technology being developed for the Integrated Display and Environmental Awareness System (IDEAS) project is a wearable computer system with an optical heads-up display (HUD) providing various means of communication and data manipulation to the user. The wearable computer, in the form of smart glasses, would allow personnel to view and modify critical information on a transparent, interactive display. This is presented in their unobstructed field of view, without taking their eyes or hands away from their critical work. The product is being designed in a modular manner so that the user can adjust the capabilities of the device depending on need. IDEAS is a full featured hardware and softwaresystem built to enhance the capabilities of theNASA work force on the ground and in space.

Wearables↗
NASA NTRS1980

Documentation of program AFTBDY to generate coordinate system for 3D after body using body fitted curvilinear coordinates, part 1

The computer program AFTBDY generates a body fitted curvilinear coordinate system for a wedge curved after body. This wedge curved after body is being used in an experimental program. The coordinate system generated by AFTBDY is used to solve 3D compressible N.S. equations. The coordinate system in the physical plane is a cartesian x,y,z system, whereas, in the transformed plane a rectangular xi, eta, zeta system is used. The coordinate system generated is such that in the transformed plane coordinate spacing in the xi, eta, zeta direction is constant and equal to unity. The physical plane coordinate lines in the different regions are clustered heavily or sparsely depending on the regions where physical quantities to be solved for by the N.S. equations have high or low gradients. The coordinate distribution in the physical plane is such that x stays constant in eta and zeta direction, whereas, z stays constant in xi and eta direction. The desired distribution in x and z is input to the program. Consequently, only the y-coordinate is solved for by the program AFTBDY.

Kumar, D.↗