SEARCH · Search NASA

Results for “ice accretion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

All sources NASA NTRS DOE OSTI

NASA NTRS1986

An experimental study of the aerodynamics of a NACA 0012 airfoil with a simulated glaze ice accretion

An experimental study was conducted in the Ohio State University subsonic wind tunnel to measure the detailed aerodynamic characteristics of an airfoil with a simulated glaze ice accretion. A NACA 0012 model with interchangeable leading edges and pressure taps every one percent chord was used. Surface pressure and wake data were taken on the airfoil clean, with forced transition and with a simulated glaze ice shape. Lift and drag penalties due to the ice shape were found and the surface pressure clearly showed that large separation bubbles were present. Both total pressure and split-film probes were used to measure velocity profiles, both for the clean model and for the model with a simulated ice accretion. A large region of flow separation was seen in the velocity profiles and was correlated to the pressure measurements. Clean airfoil data were found to compare well to existing airfoil analysis methods.

Bragg, M. B.↗

NASA NTRS2003

Measurement and Correlation of Ice Accretion Roughness

Measurements were taken of the roughness characteristics of ice accreted on NACA 0012 airfoils in the NASA Glenn Icing Research Tunnel (IRT). Tests were conducted with size scaled, using models with chords of 26.7, 53.3, and 80.0 cm, and with liquid-water content scaled, both according to previously-tested scaling methods. The width of the smooth zone which forms on either side of the leading edge of the airfoil and the diameter of the roughness elements are presented in non-dimensional form as functions of the accumulation parameter. The smooth-zone width was found to decrease with increasing accumulation parameter. The roughness-element diameter increased with accumulation parameter until a plateau was reached. This maximum diameter was about 0.06 times twice the model leading-edge radius. Neither smooth-zone width nor element diameter were affected by a change in freezing fraction from 0.2 to 0.4. Both roughness characteristics appeared to scale with model size and with liquid-water content.

Anderson, David N.↗

NASA NTRS1995

Aircraft Ice Accretion Due to Large-Droplet Icing Clouds

Studies of aircraft icing due to clouds consisting of individual droplets 10 times larger than those normally found in icing conditions are being carried out by members of the NASA Lewis Research Center's Icing Technology Branch. When encountered by an aircraft in freezing conditions, clouds consisting of large water droplets have a significantly different effect than those with normal droplets. A large-water-droplet cloud has been suggested as the cause of a commuter airplane accident in the late fall of 1994. As a result, studies of what happens to aircraft flying in these rare, but potentially very hazardous, conditions have been reemphasized.

Source record↗

NASA NTRSDate not supplied

Ice Accretion Roughness Variations on a Hybrid CRM65-Midspan Wing Model

Ice accretion roughness measurements were performed in the Icing Research Tunnel (IRT) at NASA Glenn Research Center for the Hybrid CRM65-Midspan model in a range of icing conditions. The Hybrid CRM65-Midspan model was chosen for this investigation because 1) the model exhibits high sweep relative to models previously explored in the roughness investigations, 2) the model has leading edge characteristics similar to wing shapes currently used in mid-size commercial airliners, and 3) the sweep and thickness ratios relate better to hybrid lifting body designs for N+2 and N+3 vehicles than other models available. The investigation consisted of multiple sets of tests which focused on 1) 0-angle of attack cases replicating the conditions employed by Anderson et al. (1998) using both Appendix C and SLD cloud conditions, 2) cases based on the “Max Scallop” case by Broeren et al. (2016) and a “High Temperature” case with cloud properties similar to the “Max Scallop” case. Additional tests were performed 1) based on the “Max Scallop” case with variations in freestream static temperature and 2) using test section speeds near 10,000-hold flight conditions. The point clouds were characterized using the approach of McClain and Kreeger (2013) for the ice roughness variations and using the approach of McClain (2016) for the mean ice thickness variations. The resulting roughness and mean thickness variations generally follow the temporal scaling previously identified using on airfoil models without sweep, but the collapse of the time progression profiles is not as tight as found for past measurements on models without sweep. LEWICE and modified panel-method predictions were used explore spatial roughness variations and to compare to the roughness correlations developed by McClain et al. (2021) for the “Max Scallop” cases.

Icing↗

NASA NTRS1993

Ice Accretion and Performance Degradation Calculations with LEWICE/NS

The LEWICE ice accretion computer code has been extended to include the solution of the two-dimensional Navier-Stokes equations. The code is modular and contains separate stand-alone program elements that create a grid, calculate the flow field parameters, calculate the droplet trajectory paths, determine the amount of ice growth, calculate aeroperformance changes, and plot results. The new elements of the code are described. Calculated results are compared to experiment for several cases, including both ice shape and drag rise.

Potapczuk, Mark G.↗

NASA NTRS1993

Ice accretion and performance degradation calculations with LEWICE/NS

Potapczuk, Mark G.↗

NASA NTRS2007

Water Droplet Impingement on Simulated Glaze, Mixed, and Rime Ice Accretions

Water droplet impingement data were obtained at the NASA Glenn Icing Research Tunnel (IRT) for a 36-in. chord NACA 23012 airfoil with and without simulated ice using a dye-tracer method. The simulated ice shapes were defined with the NASA Glenn LEWICE 2.2 ice accretion program and including one rime, four mixed and five glaze ice shapes. The impingement experiments were performed with spray clouds having median volumetric diameters of 20, 52, 111, 154, and 236 micron. Comparisons to the experimental data were generated which showed good agreement for the rime and mixed shapes at lower drop sizes. For larger drops sizes LEWICE 2.2 over predicted the collection efficiencies due to droplet splashing effects which were not modeled in the program. Also for the more complex glaze ice shapes interpolation errors resulted in the over prediction of collection efficiencies in cove or shadow regions of ice shapes.

Papadakis, Michael↗

NASA NTRS1996

Spectral Analysis and Experimental Modeling of Ice Accretion Roughness

A self-consistent scheme for relating wind tunnel ice accretion roughness to the resulting enhancement of heat transfer is described. First, a spectral technique of quantitative analysis of early ice roughness images is reviewed. The image processing scheme uses a spectral estimation technique (SET) which extracts physically descriptive parameters by comparing scan lines from the experimentally-obtained accretion images to a prescribed test function. Analysis using this technique for both streamwise and spanwise directions of data from the NASA Lewis Icing Research Tunnel (IRT) are presented. An experimental technique is then presented for constructing physical roughness models suitable for wind tunnel testing that match the SET parameters extracted from the IRT images. The icing castings and modeled roughness are tested for enhancement of boundary layer heat transfer using infrared techniques in a "dry" wind tunnel.

Orr, D. J.↗

NASA NTRS2018

Icing Simulation Research Supporting the Ice-Accretion Testing of Large-Scale Swept-Wing Models

The work summarized in this report is a continuation of NASA's Large-Scale, Swept-Wing Test Articles Fabrication; Research and Test Support for NASA IRT contract (NNC10BA05 -NNC14TA36T) performed by Boeing under the NASA Research and Technology for Aerospace Propulsion Systems (RTAPS) contract. In the study conducted under RTAPS, a series of icing tests in the Icing Research Tunnel (IRT) have been conducted to characterize ice formations on large-scale swept wings representative of modern commercial transport airplanes. The outcome of that campaign was a large database of ice-accretion geometries that can be used for subsequent aerodynamic evaluation in other experimental facilities and for validation of ice-accretion prediction codes.

Aerodynamics↗

NASA NTRS1990

Development of an unstructured mesh/Navier-Stokes method for aerodynamics of aircraft with ice accretions

An advanced flowfield prediction method for airfoils with leading edge ice accretions was developed and applied. The method is intended to be eventually used in an aircraft icing analysis. The flowfield is obtained by solving the Euler or Navier-Stokes equations on an unstructured triangular mesh. A new method has been developed to permit efficient mesh generation while providing high grid resolution near complicated airfoil ice accumulations. Unstructured-mesh Euler calculations are presented for clean and iced airfoils; the results are compared to similar structured-mesh calculations to demonstrate the new method's accuracy and efficiency.

Caruso, Steven C.↗

NASA NTRS2000

Application of Pressure-Sensitive Paint to Ice-Accreted Wind Tunnel Models

Pressure-sensitive paint (PSP) has been successfully used to measure global surface pressures on an ice-accreted model in an icing wind tunnel at NASA Glenn Research Center. Until now, the PSP technique has been limited to use in normal wind tunnels and clear flight environments. This is the first known application of PSP directly to ice in subfreezing conditions. Several major objectives were achieved in these tests. The procedure for applying the coating in the subfreezing tunnel environment was verified. Inspection of the painted ice surface revealed that the paint did not alter the original ice shape and adhered well over the entire coated area. Several procedures were used to show that the paint responded to changes in air pressure and that a repeatable pressure-dependent calibration could be achieved on the PSP-coated surfaces. Differences in pressure measurements made simultaneously on the ice and the metal test model are not yet fully understood, and techniques to minimize or correct them are being investigated.

Bencic, Timothy J.↗

NASA NTRS2019

Ice-Crystal Icing Accretion Studies at the NASA Propulsion Systems Laboratory

This paper describes an ice-crystal icing experiment conducted at the NASA Propulsion System Laboratory during June 2018. This test produced ice shape data on an airfoil for different test conditions similar to those inside the compressor region of a turbo-fan jet engine. Mixed-phase icing conditions were generated by partially freezing out a water spray using the relative humidity of flow as the primary parameter to control freeze-out. The paper presents the ice shape data and associated conditions which include pressure, velocity, temperature, humidity, total water content, melt ratio, and particle size distribution. The test featured a new instrument traversing system which allowed surveys of the flow and cloud. The purpose of this work was to provide experimental ice shape data and associated conditions to help develop and validate ice-crystal icing accretion models. The results support previous experimental observations of a minimum melt-ratio threshold for accretion to occur as well as the existence of a plateau region where the icing severity is high for a range of melt ratios. However, a maximum limit for melt ratio, which is suggested in the ice crystal icing literature, was not observed perhaps complicated by the potential for some supercooling of the water at these conditions.

Engine Icing↗

NASA NTRS2013

Aerodynamic Classification of Swept-Wing Ice Accretion

The continued design, certification and safe operation of swept-wing airplanes in icing conditions rely on the advancement of computational and experimental simulation methods for higher fidelity results over an increasing range of aircraft configurations and performance, and icing conditions. The current state-of-the-art in icing aerodynamics is mainly built upon a comprehensive understanding of two-dimensional geometries that does not currently exist for fundamentally three-dimensional geometries such as swept wings. The purpose of this report is to describe what is known of iced-swept-wing aerodynamics and to identify the type of research that is required to improve the current understanding. Following the method used in a previous review of iced-airfoil aerodynamics, this report proposes a classification of swept-wing ice accretion into four groups based upon unique flowfield attributes. These four groups are: ice roughness, horn ice, streamwise ice, and spanwise-ridge ice. For all of the proposed ice-shape classifications, relatively little is known about the three-dimensional flowfield and even less about the effect of Reynolds number and Mach number on these flowfields. The classifications and supporting data presented in this report can serve as a starting point as new research explores swept-wing aerodynamics with ice shapes. As further results are available, it is expected that these classifications will need to be updated and revised.

Broeren, Andy↗

NASA NTRS2013

Aerodynamic Classification of Swept-Wing Ice Accretion

The continued design, certification and safe operation of swept-wing airplanes in icing conditions rely on the advancement of computational and experimental simulation methods for higher fidelity results over an increasing range of aircraft configurations and performance, and icing conditions. The current stateof- the-art in icing aerodynamics is mainly built upon a comprehensive understanding of two-dimensional geometries that does not currently exist for fundamentally three-dimensional geometries such as swept wings. The purpose of this report is to describe what is known of iced-swept-wing aerodynamics and to identify the type of research that is required to improve the current understanding. Following the method used in a previous review of iced-airfoil aerodynamics, this report proposes a classification of swept-wing ice accretion into four groups based upon unique flowfield attributes. These four groups are: ice roughness, horn ice, streamwise ice and spanwise-ridge ice. In the case of horn ice it is shown that a further subclassification of "nominally 3D" or "highly 3D" horn ice may be necessary. For all of the proposed ice-shape classifications, relatively little is known about the three-dimensional flowfield and even less about the effect of Reynolds number and Mach number on these flowfields. The classifications and supporting data presented in this report can serve as a starting point as new research explores swept-wing aerodynamics with ice shapes. As further results are available, it is expected that these classifications will need to be updated and revised.

Diebold, Jeff M.↗

NASA NTRS2013

Aerodynamic Classification of Swept-Wing Ice Accretion

The continued design, certification and safe operation of swept-wing airplanes in icing conditions rely on the advancement of computational and experimental simulation methods for higher fidelity results over an increasing range of aircraft configurations and performance, and icing conditions. The current state-of-the-art in icing aerodynamics is mainly built upon a comprehensive understanding of two-dimensional geometries that does not currently exist for fundamentally three-dimensional geometries such as swept wings. The purpose of this report is to describe what is known of iced-swept-wing aerodynamics and to identify the type of research that is required to improve the current understanding. Following the method used in a previous review of iced-airfoil aerodynamics, this report proposes a classification of swept-wing ice accretion into four groups based upon unique flowfield attributes. These four groups are: ice roughness, horn ice, streamwise ice and spanwise-ridge ice. In the case of horn ice it is shown that a further subclassification of nominally 3D or highly 3D horn ice may be necessary. For all of the proposed ice-shape classifications, relatively little is known about the three-dimensional flowfield and even less about the effect of Reynolds number and Mach number on these flowfields. The classifications and supporting data presented in this report can serve as a starting point as new research explores swept-wing aerodynamics with ice shapes. As further results are available, it is expected that these classifications will need to be updated and revised.

Diebold, Jeff M.↗

NASA NTRS1988

Navier-Stokes solutions of flowfield characteristics produced by ice accretion

The flowfield and resultant heat transfer rates over a series of ice accretion shapes have been obtained through numerical solutions of the Navier-Stokes equations. The influence of roughness is modeled by including blockage, form drag and stagnation heating effects as source terms in the governing equations. Using the flowfield information obtained from the Navier-Stokes equations the droplet impingement efficiencies are computed using a PNS-type solving scheme. Good agreement is achieved between the numerical results and experimental data.

Scott, J. N.↗

NASA NTRS2012

A Systems-Level Perspective on Engine Ice Accretion

Talk covers: (1) Problem of Engine Power Loss;(2) Modeling Engine Icing Effects; (3) Simulation of Engine Rollback; (4) Icing/Engine Control System Interaction; (5) Detection of Ice Accretion; (6) Potential Mitigation Strategies.

May, Ryan David↗

NASA NTRS1987

Analytical determination of propeller performance degradation due to ice accretion

A computer code capable of computing the propeller performance for clean, glaze, or rime ice propeller configurations to determine the performance degradation resulting from a given icing encounter has been developed. The inviscid, incompressible flowfield at each specified propeller radial location is first computed using the Theodorsen method. A droplet trajectory computation then calculates the droplet impingement points and airfoil collection efficiency for each radial location. User-selectable empirical correlations are available for determining the aerodynamic penalties due to ice accretion. Propeller performance is finally computed using strip analysis for either the clean or iced propeller. In the iced mode, the thrust and torque coefficient equations are modified by the drag and lift coefficient increments due to ice to obtain the appropriate iced values. Comparison with available experimental propeller icing data shows generally good agreement. The code's capability of properly predicting the thrust coefficient, power coefficient, and propeller efficiency of an iced propeller is shown to be dependent on the choice of empirical correlation employed as well as on the proper specification of the radial icing extent and propeller blade angle.

Miller, T. L.↗