Search NASA⌕ Search

SEARCH · Search NASA

Results for “inverted structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

The solar ionisation rate deduced from Ulysses measurements and its implications to interplanetary Lyman alpha-intensity

We have developed a computer code which can be used to study 3-dimensional and time-dependent effects of the solar cycle on the interplanetary (IP) hydrogen distribution. The code is based on the inverted Monte Carlo simulation. In this work we have modelled the temporal behaviour of the solar ionisation rate. We have assumed that during the most of the time of the solar cycle there is an anisotopic latitudinal structure but right at the solar maximum the anisotropy disappears. The effects of this behaviour will be discussed both in regard to the IP hydrogen distribution and IP Lyman a a-intensity.

Summanen, T.↗
NASA NTRS1997

Measurement of Vortex Strength and Core Diameter in the Wake of a Hovering Rotor

Detailed hot wire measurements have been acquired in the tip vortex of a three-bladed model tilt rotor in hover. Testing was conducted at a rotor tip speed of 752 ft/sec, a Reynolds number (based on blade tip chord) of 1.77 x 10(exp 6), for thrust coefficients up to 0.0160. A figure shows the hot wire mounted above the inverted rotor at the Outside Aerodynamic Rotor Facility (OARF) at NASA Ames Research Center. Strobed shadowgraph flow visualization was used to define the vortex trajectory as an aid in hot wire positioning. Considerable variations in tip vortex structure with time were observed, even from the same blade, under essentially uniform test conditions. The only velocity signatures analyzed were those corresponding to passage of the probe directly through the center of the vortex. These time histories were ensemble averaged after compensating for jitter in the vortex arrival time at the probe, thereby retaining the core structure with minimal smearing. An example of a mean velocity signature, after ensemble averaging, is shown. The mean velocity signature was analyzed under the assumption of constant (unknown) translation speed of the vortex filament past the fixed probe. The translation speed of the vortex is deduced and the vortex strength and core diameter inferred. The results were highly unexpected. The indicated vortex strength is seen to decrease rapidly after first blade passage. In addition, the core radius is seen to decrease with increasing wake age, not increase as might be expected from simple diffusion.

Wadcock, Alan J.↗
NASA NTRS1972

Shielded silicon gate complementary MOS integrated circuit.

An electrostatic shield for complementary MOS integrated circuits was developed to minimize the adverse effects of stray electric fields created by the potentials in the metal interconnections. The process is compatible with silicon gate technology. N-doped polycrystalline silicon was used for all the gates and the shield. The effectiveness of the shield was demonstrated by constructing a special field plate over certain transistors. The threshold voltages obtained on an oriented silicon substrate ranged from 1.5 to 3 V for either channel. Integrated inverters performed satisfactorily from 3 to 15 V, limited at the low end by the threshold voltages and at the high end by the drain breakdown voltage of the n-channel transistors. The stability of the new structure with an n-doped silicon gate as measured by the shift in C-V curve under 200 C plus or minus 20 V temperature-bias conditions was better than conventional aluminum gate or p-doped silicon gate devices, presumably due to the doping of gate oxide with phosphorous.

Lin, H. C.↗
NASA NTRS1993

Geostatistical evaluation of satellite radar altimetry for high-resolution mapping of Lambert Glacier, Antarctica

The potential of satellite radar altimetry for high-resolution mapping of Antarctic ice streams is evaluated, using retracked and slope-corrected data from the Lambert Glacier and Amery Ice Shelf area, East Antarctica, acquired by Geosat during the Exact Repeat Mission (ERM), 1986-89. The map area includes lower Lambert Glacier north of 72.18 deg S, the southern Amery Ice Shelf, and the grounded inland ice sheet on both sides. The Geosat ERM altimetry is found to provide substantially more complete coverage than the 1978 Seasat altimetry, due to improved tracking. Variogram methods are used to estimate the noise levels in the data as a function of position throughout the map area. The spatial structure in the data is quantified by constructing experimental variograms using altimetry from the area of the grounding zone of Lambert Glacier, which is the area chiefly of interest in this topographically complex region. Kriging is employed to invert the along-track height measurements onto a fine-scale 3 km grid. The unsmoothed along-track Geosat ERM altimetry yields spatially continuous maps showing the main topographic features of lower Lambert Glacier, upper Amery Ice Shelf and the adjacent inland ice sheet. The probable position of the grounding line of Lambert Glacier is identified from a break in slope at the grounded ice/floating ice transition. The approximate standard error of the kriged map is inferred from the data noise levels.

Herzfeld, Ute C.↗
NASA NTRS1997

Geopotential Error Analysis from Satellite Gradiometer and Global Positioning System Observables on Parallel Architecture

The recovery of a high resolution geopotential from satellite gradiometer observations motivates the examination of high performance computational techniques. The primary subject matter addresses specifically the use of satellite gradiometer and GPS observations to form and invert the normal matrix associated with a large degree and order geopotential solution. Memory resident and out-of-core parallel linear algebra techniques along with data parallel batch algorithms form the foundation of the least squares application structure. A secondary topic includes the adoption of object oriented programming techniques to enhance modularity and reusability of code. Applications implementing the parallel and object oriented methods successfully calculate the degree variance for a degree and order 110 geopotential solution on 32 processors of the Cray T3E. The memory resident gradiometer application exhibits an overall application performance of 5.4 Gflops, and the out-of-core linear solver exhibits an overall performance of 2.4 Gflops. The combination solution derived from a sun synchronous gradiometer orbit produce average geoid height variances of 17 millimeters.

Schutz, Bob E.↗
NASA NTRS1971

On the inversion of limb radiance measurements. I.

The calculation of limb radiance as a function of tangent height is shown to require information about the vertical distribution of temperature and the pressure at one level. Conversely, given the limb radiance curve and the pressure corresponding to one tangent point, it is possible to determine the temperature profile as a function of height relative to the given level, using an iterative technique. Results of inverting synthesized realistic data are presented. The data include the effects of water vapor and ozone contamination of the carbon dioxide signal, instrument field of view, and random and systematic noise for real atmospheres having small-scale vertical structure.

Gille, J. C.↗
NASA NTRS2005

Global Admittance Estimates of Elastic and Crustal Thickness of Venus: Results from Top, Hot Spot, and Bottom Loading Models

We have calculated admittance spectra using the spatio-spectral method [14] for Venus by moving the central location of the spectrum over a 1 grid, create 360x180 admittance spectra. We invert the observed admittance using top-loading (TL), hot spot (HS), and bottom loading (BL) models, resulting in elastic, crustal, and lithospheric thickness estimates (Te, Zc, and Zl) [0]. The result is a global map for interpreting subsurface structure. Estimated values of Te and Zc concur with previous TL local admittance results, but BL estimates indicate larger values than previously suspected.

Smrekar, S. E.↗
NASA NTRS1981

Flame structure in a swirl stabilized combustor inferred by radiant emission measurements

Results of measurements of time-averaged chemiluminescent emissions from CH, OH, and CO2 and of Na tracer emissions along lateral lines-of-sight through a cylindrical premixed, swirl-stabilized combustor are reported. Assuming axial symmetry and small optical depth, raw data are inverted to obtain local emission levels from these species as a function of radius. The chemiluminescent emissions are interpreted as signatures of chemical reaction and used in determining the regions of reactions and heat release in the combustor. The data are compared with composition and velocity data obtained in the combustor for identical operating conditions. The results demonstrate that reaction occurs in a relatively narrow, turbulent flame-like combustion zone which begins upstream of the time-averaged location of the swirl-induced recirculation zone and propagates around and laterally away from the recirculation zone into the unburned gas.

Beyler, C. L.↗
NASA NTRS1979

High resolution transmission electron microscopy of two stony meteorites - Murchison and Kenna

Matrix material from the Murchison C2(M) carbonaceous chondrite and less than micrometer-size pyroxene inclusions in an olivine from the Kenna ureilite have been characterized using high resolution transmission electron microscopy. A diversity of textures and mineral associations, including serpentine-type and brucite-type mixed-layering, occur in the Murchison matrix. Such mixed layer structures are new types of layer silicate. Their presence in the matrix may prove to be genetically significant. The Kenna inclusions, formed at the olivine grain margins, are of two types: (1) a disordered orthopyroxene-clinopyroxene which may have inverted from protopyroxene and (2) a pigeonite with narrow anti-phase domains (80 A to 250 A) and boundaries parallel to (100).

Mackinnon, I. D. R.↗
NASA NTRS2018

Integration of Multilevel Superconducting Buried Wiring Layers with Transition-Edge Sensor Detectors for Large Scale Arrays

Lynx, one of the four mission concepts under consideration for the next Astrophysics DecadalReview, will include a microcalorimeter array consisting of more than 100,000 pixels in a compact arrangement with absorber pitch as small as 25 microns. In order to realize the desired array scale, fine-pitch multi-level superconducting wiring with high yield, compatible with rapid expansion of our hydra absorber designs, is essential. We have demonstrated a method of integrating transition edge sensor (TES) microcalorimeters with suitable multilevel buried wiring, fabricated at MIT Lincoln Laboratory using advanced tools dedicated to superconducting circuit fabrication. The TES Mo/Au bilayer is deposited on a high-quality oxide surface created by chemical-mechanical polishing, allowing tight specifications on the TES superconducting transition and link conductivity to be achieved even though the process order has been inverted. The TESs contact the top-level niobium wiring through vias etched through silicon dioxide down to the topmost wiring layer. The article discusses the overall fabrication process, as wellas the behavior of sensors with different via designs, proximity structures, and lateral sizes. An initial iteration of the integrated fabrication process indicates that microcalorimeters fabricated in this way should meet mission specifications using a Mo/Au bilayer with a reasonable critical temperature below 100 mK.

Detector↗
NASA NTRS2011

Development of a Practical Broadband Active Vibration Control System

The goal of this work is to develop robust, lightweight, and low-power control units that can be used to suppress structural vibration in flexible aerospace structures. In particular, this paper focuses on active damping, which is implemented using compact decentralized control units distributed over the structure. Each control unit consists of a diamond-shaped piezoelectric patch actuator, three miniature accelerometers, and analog electronics. The responses from the accelerometers are added together and then integrated to give a signal proportional to velocity. The signal is then inverted, amplified, and applied to the actuator, which generates a control force that is out of phase with the measured velocity. This paper describes the development of the control system, including a detailed description of the control and power electronics. The paper also presents experimental results acquired on a Plexiglas window blank. Five identical control units installed around the perimeter of the window achieved 10 dB peak reductions and a 2.4 dB integrated reduction of the spatially averaged velocity of the window between 500 and 3000 Hz.

Schiller, Noah H.↗
NASA NTRS2004

Temporal-Spatial Structure of Magnetic Merging at the Magnetopause Inferred from 557.7-nm All-Sky Images

We demonstrate that high-resolution 557.7-nm all-sky images are useful tools for investigating the spatial and temporal evolution of merging on the dayside magnetopause. Analysis of ground and satellite measurements leads us to conclude that high-latitude merging events can occur at multiple sites simultaneously and vary asynchronously on time scales of 30 s to 3 min. Variations of 557.7 nm emissions were observed at a 10 s cadence at Ny-Alesund on 19 December 2001, while significant changes in the IMF clock angle were reaching the magnetopause. The optical patterns are consistent with a scenario in which merging occurs around the rim of the high-latitude cusp at positions dictated by the IMF clock angle. Electrons energized at merging sites represent plausible sources for 557.7 nm emissions in the cusp. Polar observations at the magnetopause have directly linked enhanced fluxes of > or = 0.5 keV electrons with merging. Spectra of electrons responsible for some of the emissions, measured during a DMSP F15 overflight, exhibit "inverted-V" features, indicating further acceleration above the ionosphere. SuperDARN spectral width boundaries, characteristic of open-closed field line transitions, are located at the equatorward edge of the 557.7nm emissions. Optical data suggest that with IMF B(sub Y) > 0, the Northern Hemisphere cusp divides into three source regions. When the IMF clock angle was approx. 150 deg structured 557.7-nm emissions came from east of the 13:00 MLT meridian. At larger clock angles the emissions appeared between 12:00 and 13:00 MLT. No significant 557.7-nm emissions were detected in the prenoon MLT sector. MHD simulations corroborate our scenario, showing that with the observed large dipole-tilt and IMF clock angles, merging sites develop near the front and eastern portions of the high-altitude cusp rim in the Northern Hemisphere and near the western part of the cusp rim in the Southern Hemisphere.

Maynard, N. C.↗
NASA NTRS2021

Anisotropic Wet Etching of Si as a Fabrication Tool Enabling 3-D Microphotonics Structures and Devices

It is shown that due to high speed and large volume of production, anisotropic wet etching of Si is a unique method of manufacturing high quality micropyramidal arrays for silicon photonics. Four types of arrays were fabricated: (i) square pyramids with the 54.7 slope of the sidewall surface, (ii) microcones with the 45 slope of sidewall surface, (iii) inverted square pyramids with 54.7 slope, and (iv) inverted triangular pyramids with different angles of the sidewalls. It is shown that the first type of arrays has a capability to produce tightly focused mid-wave infrared (MWIR) beams at the tips of the pyramids. Other arrays can be also used as light concentrators and various multifunctional microphotonic components.

Astratov, Vasily N.↗
NASA NTRS2003

Field Effects of Buoyancy on a Premixed Turbulent Flame Studied by Particle Image Velocimetry

Typical laboratory flames for the scientific investigation of flame/turbulence interactions are prone to buoyancy effects. Buoyancy acts on these open flame systems and provides upstream feedbacks that control the global flame properties as well as local turbulence/flame interactions. Consequently the flame structures, stabilization limits, and turbulent reaction rates are directly or indirectly coupled with buoyancy. The objective of this study is to characterize the differences between premixed turbulent flames pointing upwards (1g), pointing downwards (-1g), and in microgravity (mg). The configuration is an inverted conical flame stabilized by a small cone-shaped bluff body that we call CLEAN Flames (Cone-Stabilized Lean Flames). We use two laser diagnostics to capture the velocity and scalar fields. Particle image velocimetry (PIV) measures the mean and root mean square velocities and planar imaging by the flame fronts method outlines the flame wrinkle topology. The results were obtained under typical conditions of small domestic heating systems such as water heaters, ovens, and furnaces. Significant differences between the 1g and -1g flames point to the need for including buoyancy contributions in theoretical and numerical calculations. In Earth gravity, there is a complex coupling of buoyancy with the turbulent flow and heat release in the flame. An investigation of buoyancy-free flames in microgravity will provide the key to discern gravity contributions. Data obtained in microgravity flames will provide the benchmark for interpreting and analyzing 1g and -1g flame results.

Cheng, Robert K.↗
NASA NTRS2009

Efficient Multiplexer FPGA Block Structures Based on G4FETs

Generic structures have been conceived for multiplexer blocks to be implemented in field-programmable gate arrays (FPGAs) based on four-gate field-effect transistors (G(sup 4)FETs). This concept is a contribution to the continuing development of digital logic circuits based on G4FETs and serves as a further demonstration that logic circuits based on G(sup 4)FETs could be more efficient (in the sense that they could contain fewer transistors), relative to functionally equivalent logic circuits based on conventional transistors. Results in this line of development at earlier stages were summarized in two previous NASA Tech Briefs articles: "G(sup 4)FETs as Universal and Programmable Logic Gates" (NPO-41698), Vol. 31, No. 7 (July 2007), page 44, and "Efficient G4FET-Based Logic Circuits" (NPO-44407), Vol. 32, No. 1 ( January 2008), page 38 . As described in the first-mentioned previous article, a G4FET can be made to function as a three-input NOT-majority gate, which has been shown to be a universal and programmable logic gate. The universality and programmability could be exploited to design logic circuits containing fewer components than are required for conventional transistor-based circuits performing the same logic functions. The second-mentioned previous article reported results of a comparative study of NOT-majority-gate (G(sup 4)FET)-based logic-circuit designs and equivalent NOR- and NAND-gate-based designs utilizing conventional transistors. [NOT gates (inverters) were also included, as needed, in both the G(sup 4)FET- and the NOR- and NAND-based designs.] In most of the cases studied, fewer logic gates (and, hence, fewer transistors), were required in the G(sup 4)FET-based designs. There are two popular categories of FPGA block structures or architectures: one based on multiplexers, the other based on lookup tables. In standard multiplexer- based architectures, the basic building block is a tree-like configuration of multiplexers, with possibly a few additional logic gates such as ANDs or ORs. Interconnections are realized by means of programmable switches that may connect the input terminals of a block to output terminals of other blocks, may bridge together some of the inputs, or may connect some of the input terminals to signal sources representing constant logical levels 0 or 1. The left part of the figure depicts a four-to-one G(sup 4)FET-based multiplexer tree; the right part of the figure depicts a functionally equivalent four-to-one multiplexer based on conventional transistors. The G(sup 4)FET version would contains 54 transistors; the conventional version contains 70 transistors.

Vatan, Farrokh↗
NASA NTRS1983

Reduced Aircraft-Engine Noise

Shock structure modified to eliminate associated noise. Shock wave repeats in supersonic flow adjoining subsonic flow layer. When supersonic layer is added, shock wave is partially transmitted at interface. Result is almost total elimination of shock pattern after one or two reflections. Technique applicable to inverted as well as to normal-velocity-profile coannular jets and used to eliminate or reduce shock noise of turbojet engines.

Tanna, H. K.↗
NASA NTRS1984

The p-wave upper mantle structure beneath an active spreading centre - The Gulf of California

Over 1400 seismograms of earthquakes in Mexico are analyzed and data sets for the travel time, apparent phase velocity, and relative amplitude information are utilized to produce a tightly constrained, detailed model for depths to 900 km beneath an active oceanic ridge region, the Gulf of California. The data are combined by first inverting the travel times, perturbing that model to fit the p-delta data, and then performing trial and error synthetic seismogram modelling to fit the short-period waveforms. The final model satisfies all three data sets. The ridge model is similar to existing upper mantle models for shield, tectonic-continental, and arc-trench regimes below 400 km, but differs significantly in the upper 350 km. Ridge model velocities are very low in this depth range; the model 'catches up' with the others with a very large velocity gradient from 225 to 390 km.

Walck, M. C.↗
NASA NTRSDate not supplied

Observation of Deep Convective Cloud-Top Height and Vertical Temperature Structure of Hurricane Using Hyperspectral Infrared Sounder and its Single-Field-View Retrieval Products

Hurricanes, severe tropical cyclones (TC), or typhoons are significant natural disasters that often result in substantial loss of life and property damage. Numerous studies have indicated that changes in TC intensity are closely linked to deep convective clouds (DCC), with stronger TCs typically exhibiting higher cloud top heights (CTH) compared to weaker TCs. The CTH can help determine if a tropical depression is at the onset of rapid intensification based on case studies. Therefore, accurate determination of TC CTH will be greatly helpful for monitoring TC development and studying TC dynamics. One traditional and most common method to derive CHT from satellite observations is using the thermal brightness temperature in atmospheric channels to match the sounding temperature profile. However, it was found that thermally derived CTH has a lower bias of approximately 1 km, and this bias tends to worsen for the tallest clouds. A new method using the hyperspectral infrared sounder will be presented. From the measurements of Cross-track Infrared Sounder (CrIS) on S-NPP and J-1, along with radiative transfer simulations, we identified the inverted-V spectral feature in the ozone (O3) band (near 9.6 μm) corresponding to high clouds. The depth of the inverted-V can be used to estimate the CTH. Since the depth is computed using the peak absorption O3 channel and the nearby most transparent O3 channel in this O3 band, the uncertainties associated with cloud emissivity and scattering by cloud particles in the traditional method can be ignored. From several hurricane case studies, we found that the CHT derived using this method can accurately capture the structure of the cloud tops in the eyewall, spiral rainbands, and surrounding regions. For example, Hurricane Dorian on September 2, 2019, showed a nicely outward-sloping and circular shape eye cloud in the early morning, but the circular shape of the eyewall cloud became distorted in the afternoon. For various hurricanes we examined, the distribution of CHT for the eyewall clouds differed significantly. To better study the thermodynamic structure of hurricane clouds, this research will analyze the vertical temperature profiles from a new single Field of View (SFOV) Sounder Atmospheric Products (SiFSAP), derived using CrIS and the Advanced Technology Microwave Sounder (ATMS) onboard SNPP and JPSS-1. SiFSAP has a spatial resolution of 15 km at nadir, which surpasses most global weather and climate models and other current operational sounding products. The combined use of ATMS and CrIS allows for retrievals near hurricane eyewalls and spiral rainbands. Wind fields from NASA’s Modern-Era Retrospective Analysis for Research and Applications Version-2 (MERRA-2) and ERA5 will be used to characterize transport, and comparisons between the model temperature and water vapor profiles with the corresponding SiFSAP products will also be provided.

SiFSAP↗