Search NASA⌕ Search

SEARCH · Search NASA

Results for “large-scale computing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

The correlation function for density perturbations in an expanding universe. IV - The evolution of the correlation function

The evolution of the two-point correlation function for the large-scale distribution of galaxies in an expanding universe is studied on the assumption that the perturbation densities lie in a Gaussian distribution centered on any given mass scale. The perturbations are evolved according to the Friedmann equation, and the correlation function for the resulting distribution of perturbations at the present epoch is calculated. It is found that: (1) the computed correlation function gives a satisfactory fit to the observed function in cosmological models with a density parameter (Omega) of approximately unity, provided that a certain free parameter is suitably adjusted; (2) the power-law slope in the nonlinear regime reflects the initial fluctuation spectrum, provided that the density profile of individual perturbations declines more rapidly than the -2.4 power of distance; and (3) both positive and negative contributions to the correlation function are predicted for cosmological models with Omega less than unity.

Mcclelland, J.↗

Development of a facility for large-scale testing of multistory buildings

Current experimental research pertaining to response of structures subjected to lateral loads such as strong winds or earthquake motions is limited to either tests of single structural components or small scale multistory structures. The feasibility of developing a facility where large scale multistory structures could be loaded to failure is discussed. The test facility would consist of a series of hydraulic actuators mounted on reaction frames currently in use at the Marshall Space Flight Center for structural testing of spacecraft components. The actuators would be controlled from signals computed by an on-line analysis of measured data. This method of loading could be used to simulate inertial forces resisted by a structure behaving in the non linear range of response subjected to motion at the base or to impulses along the height as would occur during a strong earthquake or wind.

Abrams, D. P.↗

Numerical investigation of turbulent channel flow

Fully developed turbulent channel flow was simulated numerically at Reynolds number 13800, based on centerline velocity and channel halt width. The large-scale flow field was obtained by directly integrating the filtered, three dimensional, time dependent, Navier-Stokes equations. The small-scale field motions were simulated through an eddy viscosity model. The calculations were carried out on the ILLIAC IV computer with up to 516,096 grid points. The computed flow field was used to study the statistical properties of the flow as well as its time dependent features. The agreement of the computed mean velocity profile, turbulence statistics, and detailed flow structures with experimental data is good. The resolvable portion of the statistical correlations appearing in the Reynolds stress equations are calculated. Particular attention is given to the examination of the flow structure in the vicinity of the wall.

Moin, P.↗

Closed coronal structures. II - Generalized hydrostatic model

Numerical computations of stationary solar coronal loop atmospheres are used to extend earlier analytical work. Two classes of loops are examined, namely symmetric loops with a temperature maximum at the top but now having a length greater than the pressure scale height and loops which have a local temperature minimum at the top. For the first class, new scaling laws are found which relate the base pressure and loop length to the base heating, the heating deposition scale height, and the pressure scale height. It is found that loops for which the length is greater than about two to three times the pressure scale height do not have stable solutions unless they have a temperature minimum at the top. Computed models with a temperature inversion at the top are permitted in a wider range of heating deposition scale height values than are loops with a temperature maximum at the top. These results are discussed in relation to observations showing a dependence of prominence formation and stability on the state of evolution of magnetic structures, and a general scenario is suggested for the understanding of loop evolution from emergence in active regions through the large-scale structure phase to opening in coronal holes.

Serio, S.↗

Cloud-particle galactic gas dynamics and star formation

Galactic gas dynamics, spiral structure, and star formation are discussed in relation to N-body computational studies based on a cloud-particle model of the interstellar medium. On the small scale, the interstellar medium is seen as cloud-dominated and supernova-perturbed. It is noted that the cloud-particle model simulates cloud-cloud collisions, the formation of stellar associations, and supernova explosions as dominant local processes. On the large scale, in response to a spiral galactic gravitational field, global density waves and galactic shocks develop having large-scale characteristics similar to those found in continuum gas dynamical studies. Both the system of gas clouds and the system of young stellar associations forming from the clouds figure in the global spiral structure. However, with the attributes of neither assuming a continuum of gas (as in continuum gas dynamical studies) or requiring a prescribed equation of state (such as the isothermal condition), the cloud-particle picture retains much of the detail lost in earlier work. By detail is meant the small-scale features and structures so important in understanding the local, turbulent state of the interstellar medium as well as the degree of raggedness often seen to be superposed on the global spiral structure.

Roberts, W. W., Jr.↗

Application of augmented-Lagrangian methods in meteorology: Comparison of different conjugate-gradient codes for large-scale minimization

A Lagrange multiplier method using techniques developed by Bertsekas (1982) was applied to solving the problem of enforcing simultaneous conservation of the nonlinear integral invariants of the shallow water equations on a limited area domain. This application of nonlinear constrained optimization is of the large dimensional type and the conjugate gradient method was found to be the only computationally viable method for the unconstrained minimization. Several conjugate-gradient codes were tested and compared for increasing accuracy requirements. Robustness and computational efficiency were the principal criteria.

Navon, I. M.↗

A numerical study of the vertical transport of momentum in a tropical rainband

The vertical transport of horizontal momentum in a convective tropical rainband is studied using a two-dimensional cloud ensemble model. Twelve simulations are made under the same large-scale conditions. The vertical transports of v momentum (parallel to the rainband) are essentially the same in all of the simulations, even though the structure of the clouds is different in each of the runs. The magnitude of the v-momentum transport by clouds is fairly large. It takes only half of a day to smooth out the tropical low-level easterly jet parallel to the rainband if no other processes are operating. The vertical transports of u momentum (perpendicular to the rainband) are quite different in all of the simulations. This difference can be explained by the dissimilarities in the distributions of horizontal momentum associated with various cloud configurations. The simulated vertical transports of horizontal momentum are compared with those computed with the Schneider and Lindzen scheme. The results suggest that their scheme is basically correct and usable if some improvements are made.

Soong, S.-T.↗

Solar Pond Fluid Dynamics and Heat Transfer

The primary objective of the solar pond research was to obtain an indepth understanding of solar pond fluid dynamics and heat transfer. The key product was the development of a validated one-dimensional computer model with the capability to accurately predict time-dependent solar pond temperature, salinities, and interface motions. Laboratory scale flow visualization experiments were conducted to better understand layer motion. Two laboratory small-scale ponds and a large-scale outdoor solar pond were designed and built to provide quantitative data. This data provided a basis for validating the model and enhancing the understanding of pond dynamic behavior.

Jones, G. F.↗

Morphologic Evolution of the Mount St. Helens Crater Area, Washington

The large rockslide-avalanche that preceded the eruption of Mount St. Helens on 18 May 1980 removed approximately 2.8 cubic km of material from the summit and north flank of the volcano, forming a horseshoe-shaped crater 2.0 km wide and 3.9 km long. A variety of erosional and depositional processes, notably mass wasting and gully development, acted to modify the topographic configuration of the crater area. To document this morphologic evolution, a series of annual large-scale topographic maps is being produced as a base for comparitive geomorphic analysis. Four topographic maps of the Mount St. Helens crater area at a scale of 1:4000 were produced by the National Mapping Division of the U. S. Geological Survey. Stereo aerial photography for the maps was obtained on 23 October 1980, 10 September 1981, 1 September 1982, and 17 August 1983. To quantify topographic changes in the study area, each topographic map is being digitized and corresponding X, Y, and Z values from successive maps are being computer-compared.

Beach, G. L.↗

Computations of ozone transport using Nimbus 7 solar backscatter ultraviolet and NOAA/National Meteorological Center data

The ozone fluxes and flux convergences within the region between 30 and 0.4 mbar for the Northern Hemisphere are investigated for the period January 1 to March 31, 1979, using Nimbus 7 solar backscatter ultraviolet ozone profiles and the meteorological data derived from NOAA satellites. The results indicate that large contributions to the ozone transport and the transport convergence are due to mean vertical advection and horizontal eddy processes. The contribution from the vertical eddies is insignificant. The transport of ozone into the polar latitudes during winter and early spring is mainly accomplished by the large-scale horizontal eddies. The results also show that more ozone is transported into the polar region by the large-scale eddies on disturbed days than on quiet days.

Wu, M.-F.↗

Temporal behavior of density perturbations in the polar wind

The time-dependent continuity and momentum equations for H(+) are solved in order to study the temporal evolution of density perturbations in the supersonic, collisionless polar wind. The results indicate that the sophisticated computer models of small-scale plasma expansions are indeed applicable to large-scale flow problems. The important prediction of the production of superthermal ions from small-scale simulations by the process of plasma expansion is borne out by the calculations in this paper. Energetic ions are produced for each type of density perturbation through the plasma expansion process. In the case of an extended density depletion, the forward-reverse shock pair forms when the depletion is very strong, but otherwise only the forward shock forms. In the case of localized density depletions, the density cavity evolves into two rarefaction waves joined by a forward-reverse shock pair. In the case of localized density enhancements, the shock pair evolves from compressive waves.

Singh, N.↗

Some physical and numerical aspects of computing the effects of viscosity on fluid flow

Some physical, analytical, and computational aspects of viscous flow are examined with reference to examples of computed flows. The discussion of the physical aspects covers the development of important scales used to reference flow phenomena in laminar and turbulent shear layers; the usefulness of the concepts of circulation and vorticity; and some relatively large-scale organized structures that have recently been identified in transitional and fully developed turbulent flows. Among the analytical aspects discussed are a compact presentation of the compressible Navier-Stokes equations, the Reynolds-averaged form of these equations, and a simplified description of some forms of turbulent models. Finally, results of a simulation of the onset of transition, direct turbulence simulations, and large-eddy simulations are given.

Lomax, H.↗

Theoretical and experimental studies in support of the geophysical fluid flow experiment

Meteorologists and astrophysicists interested in large scale planetary and solar circulations have come to recognize the importance of rotation and stratification in determining the character of these flows. In particular, the effect of latitude-dependent Coriolis force on nonlinear convection is thought to play a crucial role in such phenomena as differential rotation on the Sun, cloud band orientation on Jupiter, and the generation of magnetic fields in thermally driven dynamos. The continuous low-gravity environment of the orbiting space shuttle offers a unique opportunity to make laboratory studies of such large-scale thermally driven flows under the constraint imposed by rotation and sphericity. This is possible because polarization forces in a dielectric liquid, which are linearly dependent on fluid temperature, give rise to an effectively radial buoyancy force when a radial electrostatic field is imposed. The Geophysical Fluid Flow Cell (GFFC) is an implementation of this ideal in which fluid is contained between two rotating hemispheres that are differentially heated and stressed with a large a-c voltage. The experiment, to be flown on Spacelab III (currently set for launch April 29, 1985), will explore non-linear mode selection and high Rayleigh number turbulence in a rotating convecting spherical shell of liquid. Experiments will be carried out in a low driving parameter range where some limited numerical experimentation is currently feasible, as well as in a parameter range significantly beyond numerical computation for many years.

Hart, J.↗

An Innovative, Multidisciplinary Educational Program in Interactive Information Storage and Retrieval

There exists a large number of large-scale bibliographic Information Storage and Retrieval Systems containing large amounts of valuable data of interest in a wide variety of research applications. These systems are not used to capacity because the end users, i.e., the researchers, have not been trained in the techniques of accessing such systems. This thesis describes the development of a transportable, university-level course in methods of querying on-line interactive Information Storage and Retrieval systems as a solution to this problem. This course was designed to instruct upper division science and engineering students to enable these end users to directly access such systems. The course is designed to be taught by instructors who are not specialists in either computer science or research skills. It is independent of any particular IS and R system or computer hardware. The project is sponsored by NASA and conducted by the University of Southwestern Louisiana and Southern University.

Dominick, Wayne D.↗

The Design of PC/MISI, a PC-Based Common User Interface to Remote Information Storage and Retrieval Systems

The amount of information contained in the data bases of large-scale information storage and retrieval systems is very large and growing at a rapid rate. The methods available for assessing this information have not been successful in making the information easily available to the people who have the greatest need for it. This thesis describes the design of a personal computer based system which will provide a means for these individuals to retrieve this data through one standardized interface. The thesis identifies each of the major problems associated with providing access to casual users of IS and R systems and describes the manner in which these problems are to be solved by the utilization of the local processing power of a PC. Additional capabilities, not available with standard access methods, are also provided to improve the user's ability to make use of this information. The design of PC/MISI is intended to facilitate its use as a research vehicle. Evaluation mechanisms and possible areas of future research are described. The PC/MISI development effort is part of a larger research effort directed at improving access to remote IS and R systems. This research effort, supported in part by NASA, is also reviewed.

Dominick, Wayne D.↗

Large-Scale Boundary-Layer Control Tests on Two Wings in the NACA 20-Foot Wind Tunnel, Special Report

Tests were made in the N.A.C.A. 20-foot wind tunnel on: (1) a wing, of 6.5-foot span, 5.5-foot chord, and 30 percent maximum thickness, fitted with large end plates and (2) a 16-foot span 2.67-foot chord wing of 15 percent maximum thickness to determine the increase in lift obtainable by removing the boundary layer and the power required for the blower. The results of the tests on the stub wing appeared more favorable than previous small-scale tests and indicated that: (1) the suction method was considerably superior to the pressure method, (2) single slots were more effective than multiple slots (where the same pressure was applied to all slots), the slot efficiency increased rapidly for increasing slot widths up to 2 percent of the wing chord and remained practically constant for all larger widths tested, (3) suction pressure and power requirements were quite low (a computation for a light airplane showed that a lift coefficient of 3.0 could be obtained with a suction as low as 2.3 times the dynamic pressure and a power expenditure less than 3 percent of the rated engine power), and (4) the volume of air required to be drawn off was quite high (approximately 0.5 cubic feet per second per unit wing area for an airplane landing at 40 miles per hour with a lift coefficient of 3,0), indicating that considerable duct area must be provided in order to prevent flow losses inside the wing and insure uniform distribution of suction along the span. The results from the tests of the large-span wing were less favorable than those on the stub wing. The reasons for this were, probably: (1) the uneven distribution of suction along the span, (2) the flow losses inside the wing, (3) the small radius of curvature of the leading edge of the wing section, and (4) the low Reynolds Number of these tests, which was about one half that of the stub wing. The results showed a large increase in the maximum lift coefficient with an increase in Reynolds Number in the range of the tests. The results of drag tests showed that the profile drag of the wing was reduced and the L/D ratio was increased throughout the range of lift coefficients corresponding to take-off and climb but that the minimum drag was increased. The slot arrangement that is best for low drag is not the same, however, as that for maximum lift.

Freeman, Hugh B.↗

Photophoretic Propulsion Enabling Mesosphere Exploration NIAC Phase I Final Report

This Phase I report presents a comprehensive study on photophoretic flyers—innovative, ultralight, solar-powered vehicles that harness photophoretic forces generated via Knudsen pumping to achieve sustained flight in the mesosphere (50–80 km altitude). By integrating advanced materials such as nanocardboard— characterized by its extremely low areal density (~1 g/m²) and high bending stiffness—with ultrathin light-absorbing coatings, the project converts incident solar radiation directly into a directed thrust. Extensive experimental investigations, coupled with high-fidelity computational fluid dynamics (CFD) simulations using ANSYS Fluent, validate the concept across various three-dimensional geometries, including spherical, conical, and rocket-shaped configurations. These simulations bridge the gap between free-molecular and continuum flow regimes, demonstrating that optimized designs can generate lift forces sufficient to support kilogram-scale payloads even in low-pressure environments. At the heart of this innovation is the use of Knudsen pumping, where temperature gradients across porous surfaces induce directional gas flow, creating a modest overpressure that provides lift. The report introduces an analytical framework that interpolates between the well-known low-Reynolds number drag regime and the high-Reynolds number momentum theory. This model accurately predicts lift based on design parameters such as microchannel dimensions, porous wall geometry, areal density, and nozzle exit area. For instance, simulations indicate that 10-meter-scale structures with carefully engineered porous walls can achieve the necessary pressure differential to support scientifically significant payloads (~1 kg). The study also explores a hybrid propulsion approach that combines solar buoyancy with photophoretic lift. Initially, solar heating creates a buoyant force that elevates the flyer to mesospheric altitudes. Once in the optimal pressure range, the photophoretic mechanism—powered by Knudsen pumping—takes over as the primary source of lift, ensuring stable, long-duration flight. This dual-mode operation not only facilitates the deployment of photophoretic flyers but also broadens the potential applications for mesospheric exploration. In addition to propulsion, the report investigates the integration of photophoretic thrusters for trajectory control of existing research balloons in the upper stratosphere. By dynamically adjusting the nozzle orientation and controlling the flow-through velocity, these thrusters provide precise maneuverability, enabling the flyers to counteract atmospheric disturbances and adjust their flight paths in real time. For example, a photophoretic thruster approximately 7.5 by 7.5 meters in size could be unfolded below a payload gondola of a 60 million-cubic-foot zero-pressure balloon. Such a thruster can provide horizontal speed control of approximately 1 m/s using only sunlight and no moving parts (except those needed to track the Sun and control the jet direction). Importantly, photophoretic thrusters operate more efficiently at higher altitudes, which is complementary to known trajectory control techniques, such as propellers and tethered wings, which are more effective at lower altitudes. Finally, the report identifies three scientific research thrusts where mesospheric aircraft technology can have a profound impact: atmospheric tides, characterization of gravity waves, and investigation of mesospheric instabilities. Overall, the findings of this Phase I project represent a significant advancement in photophoretic propulsion technology. By demonstrating that large-scale, ultralight structures can be powered solely by solar radiation—via carefully engineered Knudsen pumping—this work lays a robust foundation for scalable, near-space flight architectures. Future refinements in material fabrication, structural optimization, and integrated trajectory control are expected to further enhance performance, paving the way for operational demonstrations that could revolutionize atmospheric science, remote sensing, and communication networks.

Knudsen Pump↗

ARCTRON: A Rapid Experimental Proving Ground for TPS Experiments and Arcjet Technology Development

Innovation in high-enthalpy facilities is fundamentally limited by the cost and risk of experimentation. New concepts for plasma control, diagnostics, facility components, and plasma-material interaction often require repeated iterations that are impractical to perform in production arcjets. As a result, promising ideas may remain unexplored or reach operational facilities only after significant development effort. ARCTRON is being developed as a rapid experimental proving ground where new ideas in plasma science, arcjet engineering, diagnostics, and material response can be conceived, tested, and quantitatively evaluated before transition to large-scale facilities. The platform combines radio-frequency (RF) and DC arc plasma generation, externally applied magnetic fields, configurable gas composition, reduced-pressure operation, laser heating, electrical biasing, and modular diagnostic access. These capabilities permit the plasma source, applied forcing, test article, and measurement configuration to be modified independently, allowing individual physical mechanisms to be isolated more readily than in a traditional test environment. One class of investigations addresses fundamental plasma-surface interaction physics. Conventional material tests often expose a specimen simultaneously to convective heating, reactive species, pressure, shear, radiation, and surface-current effects. The resulting material response may be measured accurately, while the contribution of each mechanism remains difficult to identify. ARCTRON is designed to vary these effects selectively. Plasma chemistry can be changed independently through configurable gas mixtures; magnetic fields and electrical biasing can modify charged-particle transport; laser heating can provide a non-plasma thermal input; and pressure, flow, and discharge mode can be varied over a broad operating space. This enables controlled tests of hypotheses involving surface catalycity, reactive-species transport, plasma-assisted oxidation, electromagnetic effects, shear, and the relative contributions of thermal and chemical loading. A second class of investigations enabled by this approach concerns the engineering of high-enthalpy facilities themselves. Arc-heated facilities are limited by electrode erosion, unstable arc attachment, localized heating, and damage to nozzles and other plasma-facing components. ARCTRON provides a lower-cost environment for testing concepts intended to mitigate these limitations. Candidate investigations include the use of applied magnetic fields to alter current paths and reduce plasma interaction with nozzle walls, ExB forcing to introduce controlled plasma rotation, magnetic or geometric approaches for distributing arc attachment, and alternative electrode or discharge configurations intended to reduce erosion and improve stability. Because the platform is reconfigurable, these concepts can be evaluated through repeated design--build--test cycles before they are considered for implementation in operational facilities. The platform also supports the development and validation of diagnostics that may be difficult to introduce initially into a large arcjet. Current and planned measurements include spatially resolved optical emission spectroscopy, electrostatic probes, fast imaging, pyrometry, calorimetry, laser-induced fluorescence, and absorption spectroscopy. These diagnostics are intended not merely to document a nominal operating condition, but to constrain the local plasma state and its relationship to component or material response. The modular facility geometry allows diagnostic concepts to be tested, calibrated, and compared under repeatable conditions before deployment in more demanding environments. ARCTRON is also supported by an integrated software suite. Automated control and data acquisition allow discharge parameters, gas composition, magnetic fields, diagnostic timing, and test configuration to be recorded as part of each experiment (STARDAC - Software for Testing, Analysis, Research Data, and Control). The Backend for Experiment Analysis, Storage, and Traceability (BEAST) is a database that provides the infrastructure needed to associate heterogeneous measurements with facility configuration, specimen identity, calibration state, geometry, and analysis provenance. This backend is particularly important for exploratory campaigns, in which many related configurations may be tested, and the value of an individual experiment depends on its connection to earlier and subsequent iterations. Complementary analysis capabilities, including computer-vision-based transient response measurements (arcjetCV), three-dimensional surface reconstruction (STARSCAN), and model-based Bayesian inference (SHIELD), and tomography data analysis (TOMATO, PuMA) can be incorporated when required by a specific hypothesis without becoming the focus of every campaign. The central objective of ARCTRON is therefore not to maximize heat flux or reproduce a complete flight environment. Its purpose is to reduce the cost and time required to ask consequential questions about plasma behavior, plasma-facing materials, diagnostics, and arcjet technology. By providing a controlled environment for rapid reconfiguration, mechanism isolation, quantitative measurement, and iterative engineering, ARCTRON can help mature concepts that would otherwise remain too speculative or too risky for evaluation in production facilities. The resulting knowledge can then guide the design of material models, focus test objectives in larger arcjets, reduce facility-development risk, and improve the physical basis of high-enthalpy ground testing. This work will present the ARCTRON architecture, operating modes, diagnostic suite, and digital experimental workflow. Initial experimental results from the first integrated operation of the facility will be presented, including flow characterization, power limitations, and deployment of the initial diagnostic suite. Ongoing development efforts aimed at catalycity characterization, magnetic plasma control, and advanced optical diagnostics will also be discussed, illustrating how the platform supports rapid iteration from concept to experiment.

experimental diagnostics↗