Results for “laser fusion” — Page 8

NASA NTRS2020

Additive Manufactured Ultra-Fine Lattice Structures for Propulsion Catalysts

Traditional mono-propulsion catalysts consist of coated ceramic or graphite foams that possess anisotropic mechanical and fluid properties limiting design, cost, availability, and operational use. Ultra-fine lattice structures are repeating unit cells with ligament thickness as small as 100 μm produced via Additive manufacture (AM). These lattice structures have the potential to replace coated foams used in a mono-propellant system catalysts. AM ultrafine lattice structures are designed to mimic the operational intent of coated foams but with improved design flexibility, compressive strength, and flow behavior printed from into a single part directly from the preferred platinum metal alloy. The investigation objective was to conduct feasibility studies of AM ultra-fine lattice structures capable of replacing coated foams with superior functionality. NASA MSFC identified desired lattice characteristics and created designs while EOS developed optimized laser powder bed fusion AM parameters to manufacture Ti6Al4V and tungsten specimens. Optimized designs, computational tools, AM parameters, and post-process methods were developed. Specimens underwent x-ray microfocus CT, metallographic inspection, compression testing, and flow testing. Results demonstrate that AM ultra-fine lattices improved geometric and performance repeatability with the potential for significantly increased availability while decreasing cost and lead time.

Omar R Mireles↗

NASA NTRSDate not supplied

Additive Manufacture of Ultra-Fine Lattice Structures of Green Propulsion Catalysts

Traditional mono-propulsion catalysts consist of coated ceramic or graphite foams that possess anisotropic mechanical and fluid properties limiting design, cost, availability, and operational use. Ultra-fine lattice structures are repeating unit cells with ligament thickness as small as 100 μm produced via Additive manufacture (AM). These lattice structures have the potential to replace coated foams used in a mono-propellant system catalysts. AM ultrafine lattice structures are designed to mimic the operational intent of coated foams but with improved design flexibility, compressive strength, and flow behavior printed from into a single part directly from the preferred platinum metal alloy. The investigation objective was to conduct feasibility studies of AM ultra-fine lattice structures capable of replacing coated foams with superior functionality. NASA MSFC identified desired lattice characteristics and created designs while EOS developed optimized laser powder bed fusion AM parameters to manufacture Ti6Al4V and tungsten specimens. Optimized designs, computational tools, AM parameters, and post-process methods were developed. Specimens underwent x-ray microfocus CT, metallographic inspection, compression testing, and flow testing. Results demonstrate that AM ultra-fine lattices improved geometric and performance repeatability with the potential for significantly increased availability while decreasing cost and lead time.

Omar Mireles↗

NASA NTRSDate not supplied

Impact of Powder Supply Variation on Mechanical Properties for Additive Manufacture of Alloy 718

The Additive Manufacturing Structural Integrity Initiative (AMSII) examined how a number of different Alloy 718 powder lots can create variation in microstructure and mechanical properties in parts fabricated using Laser Powder Bed Fusion. Being a common alloy, Alloy 718 powder can be found in a variety of compositions, fabrication techniques, and powder size distribution. Sixteen virgin powders, and three recycled powders were used to build samples for microstructure analysis, fatigue and tensile testing. The major impacts of the different powders manifested in variations in the microstructure, such as minor phases and grain size variation. There were corresponding variations in mechanical properties. A down-selection of powders were chosen for additional analysis, and a powder recyclability study was completed to look at the effect of reused powder.

Alloy 718↗

NASA NTRSDate not supplied

Hot-Fire Testing Results of Additively Manufactured NASA HR-1 towards Large Scale Implementation of Channel Wall Nozzles

Additive manufacturing (AM) has provided new design and manufacturing opportunities to reduce cost and schedules, consolidate parts, and optimize performance. One technique being evaluated is Laser Powder Directed Energy Deposition (LP-DED), which provides a significant increase in scale compared to Laser Powder Bed Fusion (L-PBF). NASA along with industry partners have been developing the LP-DED process to demonstrate internal channel geometry and development components for use in liquid rocket engine channel cooled nozzles. One material that has been the focus of this development is NASA HR-1, an Iron-Nickel based superalloy optimized for use in high pressure hydrogen environments. Material properties and process characterization has been completed on the high density thin-wall material in addition to advancements of the supply chain. NASA has also completed fabrication of several subscale and full scale channel wall nozzles in LP-DED NASA HR-1 and completed hot-fire testing. This includes refinement of the process to produce thin-walls and various channel geometries to meet the requirements for channel wall nozzle applications. This paper will provide an overview of the LP-DED process development, material characterization and properties, component manufacturing, and hot-fire testing. Hot-fire testing was completed for a lander-class 7K-lbf thrust chamber using Liquid Oxygen (LOX)/Methane. The design overview and results from hot-fire testing will be presented in addition to hardware development for future testing on 2K-lbf and 35k-lbf thrust chambers and large-scale manufacturing technology demonstrators.

Paul Gradl↗

NASA NTRS2021

The Effect of Composition on Microstructure and Properties for Additively Manufactured Superalloy 718

Additive manufacturing (AM) represents an exciting new approach towards producing metallic aerospace components. The ability to make complex geometries that were impossible to create using conventional manufacturing methods has sparked interest from the aerospace community, including NASA. The use of AM components for crucial and human rated space missions necessitates a full characterization of the differences between AM and more conventional wrought and cast processes. For this study, sixteen different commercially available superalloy 718 powder feedstocks were obtained, built using laser powder bed fusion(L-PBF), and microstructurally and mechanically analyzed. These measurements revealed a wide range of build qualities and microstructures despite all powder lots falling within the 718chemical specification and being processed using the same prescribed build and heat treatment parameters. Statistical analysis found a strong correlation of the amount of carbon in the powder with the final grain size and strength of the heat-treated 718 part. Ultimately, this study highlights the need of a refined superalloy 718 chemical specification for powder lots to be used in AM.

Timothy M Smith↗

NASA NTRSDate not supplied

Influence of Thermophysical Property Variability on Thermal Predictions of Ti-6Al-4V

The additive manufacturing (AM) industry has experienced rapid growth in recent decades as industrial interest in the process has grown. Because of this, there are many groups interested in simulations of the AM process. However, the influence of thermophysical property variability on the melt pool geometry during processing of various AM alloys is unclear. The goal of my work at NASA Langley Research Center (LaRC) was to characterize this influence on Ti-6Al-4V during AM processing alongside developing a tool to enable equivalent studies on other AM materials. To facilitate this process, a database tool was developed to contain and organize thermophysical data previously reported by primary sources. The specific thermophysical properties of interest for this study were density, specific heat capacity, and conductivity. Thermal diffusivity was calculated using the other three properties. This data was then fit with a Gaussian distribution and then randomly sampled from using Monte Carlo random value sampling. Using the Rosenthal equation, this sample data was used to simulate the temperature field during additive manufacturing and extract the melt pool geometry. Specifically, the melt pool’s length, width, and depth. This process was repeated an arbitrary number of times, with the default being 1000. Once this information was obtained, histograms were made showing the distributions of the sizes of the melt pool’s length, width, and depth. Representative statistical metrics of the distributions were calculated (mean, standard deviation, and coefficient of variance). This work found that at the simulated processing values, the melt pool’s width and depth had a 5.7% variation while the length had a 3.2% variation. Additionally, a tool was constructed to graph a thermal color map representation of the melt pool for specific, arbitrary values of density, specific heat, and conductivity. This tool allowed for more efficient plotting of individual queries of the thermophysical properties. The results that were observed in the research were that values reported in literature vary and this variance can have a significant impact on the simulation. Predictions of the melt pool’s dimensions show that length has a standard deviation of approximately 6 μm, width has a standard deviation of approximately 5 μm, and depth can vary by approximately 3 μm. Considering the mean sizes of length, width, and depth are 185 μm, 88 μm, and 44 μm respectively, such a deviation is significant. This shows that depth, for example, could be more than 10% larger or smaller than expected. This demonstrates that variability in the reported thermophysical properties are not negligible and should be expected to have an influence on the results of the laser powder bed fusion additive manufacturing process. When simulating this process in the future, measures should be taken to account for this discrepancy and the uncertainty involved

Justin Martin↗

NASA NTRSDate not supplied

Principles of Directed Energy Deposition for Aerospace Applications

Metal Additive Manufacturing is changing how components are being fabricated for rocket propulsion and aerospace applications. Many additive manufacturing technologies are evolving, and active research is being conducted across academia, industry, and government to advance processes, materials, design, post-processing, and applications. While much focus has been on Laser Powder Bed Fusion (L-PBF) techniques, several large-scale techniques are also rapidly evolving using directed energy deposition (DED) techniques. This lecture will provide an overview of various DED technologies, a comparison among the technologies, various materials, parameters used to deposit, and several examples of DED applications for propulsion and aerospace components.

Additive Manufacturing↗

NASA NTRSDate not supplied

Quick and Correlative TOF-SIMS Analysis of Dispersoid Content in Powder Feedstock and Printed Oxide Dispersion Strengthened Alloys

Oxide dispersion strengthening (ODS) of metal alloys, when combined with additive manufacturing (AM), can be used to solve high-temperature material application problems. The performance of ODS materials is dependent on nano-scale oxide being distributed uniformly throughout the metal matrix; a homogenous distribution is critical to the creep and yield strength. Therefore, quantifying and analyzing these oxide nanoparticles is essential for ODS alloy development. Assessing the chemistry and morphology of dispersoids in a material can be conducted using a variety of X-ray and electron-based methods. Time of Flight Secondary Ion Mass Spectrometry (TOF-SIMS), which assesses chemical concentrations from ion masses, provides the necessary spatial resolution and avoids potential spectral overlap of all elements present. In this work, preparing ODS powder feedstock and Laser Powder Bed Fusion AM was conducted with a NiCoCr alloy and yttria dispersoid, mixed with a Resodyn resonance mixer and printed on an EOS M100 3D printer at NASA Glenn. TOF-SIMS was performed on a Physical Electronics NanoTOF TRIFT V TOF-SIMS at Case Western Reserve University. The TOF-SIMS results collected on the feedstock powder samples correspond to the qualitative interpretation of the homogeneity of the oxide coating on the metal powder from SEM images. This provides quantitative support to the qualitative microscopy images collected earlier in the process design phase. The variance in the yttrium distribution on the powder feedstock samples also correlated with the variance of the yttrium distribution detected in the printed samples. This correlation supported the hypothesis that an even coating of yttria on the metal powders contributes to an even distribution of yttria in the printed material.

Laura G. Wilson↗

NASA NTRSDate not supplied

Modified Rosenthal Solution for Prediction of In Situ Alloyed GRCop-42 Melt Pool

Literature suggests that the energy needed to in-situ alloy material via additive manufacturing is higher per unit volume than their pre-alloyed counterparts, often despite the in-situ formation of thermodynamically favorable phases. This work, via experiments on in-situ alloyed GRCop-42 (Cu-4 at% Cr-2 at% Nb), will explore the energy needs of an elemental powder blend during in-situ alloying via laser powder bed fusion (LPBF). Empirically derived models will explore the influence of elemental thermophysical properties, net energy of in-situ reactions, and powder characteristics on the resulting LPBF energy demands, weld pool size and shape, and porosity evolution. Additionally, the influence of energy input during printing on the in-situ reaction to form Cr2Nb will be explored. Evolution of Cr2Nb dispersoid and copper grain shape, size, and texture can be related to the temperature reached, cooling rate, and time-as-melt during in-situ alloying via LPBF.

David Scannapieco↗

NASA NTRSDate not supplied

Having a Come-Apart: Lessons Learned from Additively Manufactured Hardware Failures

NASA has been engaged with additively manufactured (AM) process and component development since the 2000’s. AM offers various technical advantages, such as enhanced hardware design complexity, part consolidation, and processing of novel alloys in addition to programmatic advantages for reduction in processing time and cost. The focus of much of the AM development at NASA has been to mature the various processes, characterize material properties, develop standards, produce demonstrator parts, and integrate AM hardware in liquid rocket engines. These aspects have been demonstrated through process and design iterations using a methodical characterization, test-fail-fix cycles, as well as application and dissemination of lessons learned. In addition to these fundamental demonstrations of the AM process and hardware development, alloys that provide performance advantages in the high temperature and high-pressure environments have been matured for use in rocket engines. These environments are challenging for any alloy and any design, and the AM process is required to fully meet the intended design requirements. The importance of proper AM process was made evident in the failure of a Laser Powder Bed Fusion (L-PBF) copper-alloy combustion chamber during a hot-fire test due to a degraded material quality resulted from an AM process issue. The hot-fire test aimed to demonstrate high duty cycle under a risk-tolerant development project, where consequences of component failure would be minimal. However, the unintentional component failure emphasized the necessity of robust material characterization and rigorous process control procedures for the safe use of AM components in critical applications. In part, such concerns motivate the AM certification approach that NASA has recently adopted in NASA-STD-6030 “Additive Manufacturing Requirements for Spaceflight Systems”. This presentation provides an overview of the previously mentioned failure, a discussion on the evaluation of the failed chamber and supplemental chambers produced at the same time, a representative material samples that included intentional build witness lines, and a summary of the key results and recommendations from the evaluations. NASA continues to approach AM processes and designs with a level of risk and acceptance of failures that is appropriate for the project objectives, with the overall goal of safe implementation of AM technology and transferring AM technology into commercial space applications. The objective of this presentation is to provide awareness to the community working critical and non-critical AM components and the lessons learned on proper implementation of AM.

Additive Manufacturing↗

NASA NTRSDate not supplied

Design of a GRCop-42 Regeneratively Cooled Thrust Chamber Assembly and Feed System

An additively manufactured thrust chamber assembly was designed and printed using laser powder bed fusion. The NASA-developed material GRCop-42 was used for its high strength and high temperature characteristics. The combustion chamber and nozzle utilize regenerative coolant channels to achieve long duration hot fire tests. Design for additive manufacturing was used to create geometries not easily attainable with traditional machining. The thrust chamber assembly was post processed to ensure print quality and verify for testing. A feed system – encompassing all propellant lines, valves, sensors, and tanks – was designed and built to enable steady state, pressure regulated testing. Pressure transducers, thermocouples, and load cells were placed to enable measurements of the propellant properties and engine performance. Venturis and orifices were used throughout the system to control the flow rates to the thrust chamber. Aside from providing propellants, the feed system provides pressure using nitrogen, and purges the lines during shutdown. The design process for this testing platform is described. A testing campaign on the hardware will be conducted by the Akronauts Rocket Design Team at the University of Akron in Spring 2023.

Dillon M. Petty↗

NASA NTRSDate not supplied

Design of a GRCop-42 Regeneratively Cooled Thrust Chamber Assembly and Feed System

An additively manufactured thrust chamber assembly was designed and printed using laser powder bed fusion. The NASA-developed material GRCop-42 was used for its high strength and high temperature characteristics. The combustion chamber and nozzle utilize regenerative coolant channels to achieve long duration hot fire tests. Design for additive manufacturing was used to create geometries not easily attainable with traditional machining. The thrust chamber assembly was post processed to ensure print quality and verify for testing. A feed system – encompassing all propellant lines, valves, sensors, and tanks – was designed and built to enable steady state, pressure regulated testing. Pressure transducers, thermocouples, and load cells were placed to enable measurements of the propellant properties and engine performance. Venturis and orifices were used throughout the system to control the flow rates to the thrust chamber. Aside from providing propellants, the feed system provides pressure using nitrogen, and purges the lines during shutdown. The design process for this testing platform is described. A testing campaign on the hardware will be conducted by the Akronauts Rocket Design Team at the University of Akron in Spring 2023.

Dillon M. Petty↗

NASA NTRS2023

A 3D Printable Alloy Designed for Extreme Environments

Multiprincipal-element alloys are an enabling class of materials owing to their impressive mechanical and oxidation-resistant properties, especially in extreme environments. Here we develop a new oxide-dispersion-strengthened NiCoCr-based alloy using a model-driven alloy design approach and laser-based additive manufacturing. This oxide-dispersion-strengthened alloy, called GRX-810, uses laser powder bed fusion to disperse nanoscale Y 2 O 3 particles throughout the microstructure without the use of resource-intensive processing steps such as mechanical or in situ alloying. We show the successful incorporation and dispersion of nanoscale oxides throughout the GRX-810 build volume via high-resolution characterization of its microstructure. The mechanical results of GRX-810 show a twofold improvement in strength, over 1,000-fold better creep performance and twofold improvement in oxidation resistance compared with the traditional polycrystalline wrought Ni-based alloys used extensively in additive manufacturing at 1,093 °C. The success of this alloy highlights how model-driven alloy designs can provide superior compositions using far fewer resources compared with the ‘trial-and-error’ methods of the past. These results showcase how future alloy development that leverages dispersion strengthening combined with additive manufacturing processing can accelerate the discovery of revolutionary materials.

Timothy M. Smith↗

NASA NTRSDate not supplied

Metal Additive Manufacturing for Rocket Engines: Successes and Failures

NASA has been developing additive manufacturing (AM) for various technical and programmatic advantages for complex rocket engine and aerospace components. This maturation has focused on various AM processes, new alloys, characterizing material properties, developing standards, producing demonstrator parts, and integrating AM hardware in liquid rocket engines through test-fail-fix cycles, as well as application and dissemination of lessons learned of the AM lifecycle. The importance of proper AM processing was made evident in the failure of a Laser Powder Bed Fusion (L-PBF) copper-alloy combustion chamber during a hot-fire test due to a degraded material quality. The hot-fire test aimed to demonstrate high duty cycle under a risk-tolerant development project, where consequences of component failure would be minimal. However, the unintentional component failure emphasized the necessity of robust material characterization and rigorous process control procedures for the safe use of AM components in critical applications. This presentation provides an overview of the development failure, a discussion on the evaluation of the failed chamber and supplemental chambers produced at the same time, a representative material samples that included intentional build witness lines, and a summary of the key results and recommendations from the evaluations. NASA continues to approach AM processes and designs with a level of risk and acceptance of failures that is appropriate for the project objectives, with the overall goal of safe implementation of AM technology and transferring AM technology into commercial space applications. This presentation with provide critical awareness to the community lessons learned on proper implementation of AM.

L-PBF↗

NASA NTRSDate not supplied

Combining Data with Physical Knowledge for Uncertainty Quantification in Certification and Reliability Analysis

Unifying empirical data with predictive models can enable engineering cost-savings through certification by analysis and reliability-based design. Both concepts require rigorous uncertainty quantification (UQ) and robust understanding and treatment of relevant physics. Combining sampling-based UQ algorithms with high-fidelity simulations creates a computational bottleneck that is often alleviated through the use of machine learning (ML). ML can be used to create computationally efficient surrogates for simulations of complex or high-dimensional physical interactions (e.g., multi-phase interactions associated with melt pools in laser powder bed fusion or spatially-dependent material properties in functionally graded materials). However, negative side effects of ML may include a lack of interpretability and negative correlation between event rarity and simulation accuracy due to a lack of training data. As such, it is important to infuse ML algorithms with physics-based guardrails to provide confidence in their predictions. This talk will provide a brief review of recent NASA research at this intersection of physics-based simulation, ML, and UQ with a focus on certification and reliability analysis.

uncertainty quantification↗

NASA NTRSDate not supplied

Successes and Failures of Metal Additive Manufacturing for Rocket Engines

NASA has been developing additive manufacturing (AM) for various technical and programmatic advantages for complex rocket engine and aerospace components. This maturation has focused on various AM processes, new alloys, characterizing material properties, developing standards, producing demonstrator parts, and integrating AM hardware in liquid rocket engines through test-fail-fix cycles, as well as application and dissemination of lessons learned of the AM lifecycle. The importance of proper AM processing was made evident in the failure of a Laser Powder Bed Fusion (L-PBF) copper-alloy combustion chamber during a hot-fire test due to a degraded material quality. The hot-fire test aimed to demonstrate high duty cycle under a risk-tolerant development project, where consequences of component failure would be minimal. However, the unintentional component failure emphasized the necessity of robust material characterization and rigorous process control procedures for the safe use of AM components in critical applications. This presentation provides an overview of the development failure, a discussion on the evaluation of the failed chamber and supplemental chambers produced at the same time, a representative material samples that included intentional build witness lines, and a summary of the key results and recommendations from the evaluations. NASA continues to approach AM processes and designs with a level of risk and acceptance of failures that is appropriate for the project objectives, with the overall goal of safe implementation of AM technology and transferring AM technology into commercial space applications. This presentation with provide critical awareness to the community lessons learned on proper implementation of AM.

Additive Manufacturing↗

NASA NTRS2024

Electron Beam Welding of Additively Manufactured Niobium Alloy Heat Pipes

Additively manufactured refractory alloy-liquid metal heat pipes are being developed and tested for thermal management systems within nuclear propulsion and power applications. This study investigated electron beam (EB) welded joints on a laser powder bed fusion printed niobium alloy (C-103) and the impact of multiple joined heat pipe sections on working fluid flow and container leak-tightness. Results showed that EB welded joints connecting multiple heat pipe sections do not impact working fluid wicking behavior and the printed C-103 material and the EB welds joining the tubular sections created a leak-tight container. Interestingly, CT data showed an order of magnitude greater number and volume of porosity indications in the ground mating surface weld compared to the as-printed mating surface weld. The work concluded that AM is a viable manufacturing process for niobium alloy heat pipes and provided valuable insights for future AM heat pipe research and development.

Electron beam welding↗

NASA NTRSDate not supplied

Development and Optimization of Additively Manufactured NASA HR-1 for Space Applications

Metal additive manufacturing (AM) processes have been demonstrated to be effective at reducing costs and lead times associated with fabrication of complex propulsion component designs. Laser powder directed energy deposition (LP-DED) and laser powder bed fusion (L-PBF) are metal AM technologies that have effectively been used to produce a variety of parts for space applications. These technologies have enabled new designs and materials for these applications. The National Aeronautics and Space Administration (NASA) has identified the need to develop and advance new materials in unique space applications such as high-pressure hydrogen environments. One such metal alloy being developed for these applications is NASA HR-1. A high-strength Fe-Ni based superalloy, NASA HR-1 was designed to resist high pressure hydrogen environment embrittlement, oxidation, and corrosion. AM technologies have enabled the manufacturing of NASA HR-1 to be a feasible material for components in hydrogen environments. Development efforts for NASA HR-1 have completed build and heat treatment optimization, material characterization, thermophysical property testing, and mechanical testing in air and hydrogen environments to mature the understanding of the material. This presentation will summarize the development of NASA HR-1 for AM including composition and heat treatment optimization, microstructure characterization, and results of mechanical testing in air and high pressure hydrogen.

Additive Manufacturing↗