Search NASA⌕ Search

SEARCH · Search NASA

Results for “laser sintering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS2006

Pulsed Laser Deposition of BaCe(sub 0.85)Y(sub 0.15)0(sub 3) FILMS

Pulsed laser deposition has been used to grow nanostructured BaCe(sub 0.85)Y(sub 0.15)0(sub 3) films. The objective is to enhance protonic conduction by reduction of membrane thickness. Sintered samples and laser targets were prepared by sintering BaCe(sub 0.85)Y(sub 0.15)O(sub 3) powders derived by solid state synthesis. Films 2 to 6 m thick were deposited by KrF excimer laser on Si and porous Al2O3 substrates. Nanocrystalline films were fabricated at deposition temperatures of 600-800 C deg at O2 pressure of 30 mTorr and laser fluence of 1.2 J/cm square. Films were characterized by x-ray diffraction, scanning electron microscopy and electrical impedance spectroscopy. Dense single phase BaCe(sub 0.85)Y((sub 0.15) 0(sub 3) films with a columnar growth morphology is observed, preferred crystal growth was found to be dependent upon deposition temperature and substrate type. Electrical conductivity of bulk samples produced by solid state sintering and thin film samples were measured over a temperature range of 100 C deg to 900 C deg in moist argon. Electrical conduction of the fabricated films was 1 to 4 orders of magnitude lower than the sintered bulk samples. With respect to the film growth direction, activation energy for electrical conduction is 3 times higher in the perpendicular direction than the parallel direction.

Dynys, F. W.↗
NASA NTRS1989

Study of deposition of YBa2Cu3O7-x on cubic zirconia

Films of YBa2Cu3O7-x were grown on (100) cubic zirconia with 8 percent yttria by laser ablation from sintered targets of YBa2Cu3O7-x. The temperature of the zirconia substrate during growth was varied between 700 and 780 C. The atmosphere during growth was 170 mtorr of O2. The films were subsequently slowly cooled in-situ in 1 atm of O2. The best films were c-axis aligned and had a transition temperature of 87.7 K. The superconducting transition temperature and the X-ray diffraction analysis is reported as a function of the substrate temperature and of the angle between the laser beam and the target's normal.

Warner, Joseph D.↗
DOE OSTI2025

Enhancing low-temperature sintering in the MgO-LiF system: Mechanistic insights

In the present article, we provide compelling evidence that minor (1 wt%) additions of micron and nanometre-sized LiF particles in MgO decompose leading to free Li diffusing into MgO surfaces enhancing vacancy production during direct current sintering. The addition of nanometre-sized LiF particles leads to a > 500 °C reduction in the sintering temperature and over 99 % theoretical density of final consolidated compacts. Correlating differential scanning calorimetry with in-situ x-ray diffraction, together with Schottky calculations, post sintering electron microscopy and laser induced breakdown spectroscopy, we uncover critical insights into this impressive reduction in sintering temperature. Our quantitative analysis reveals that MgO and LiF interact at low temperatures with the diffusion of Li into the surface of MgO particles due to the intrinsic structural disorder of the LiF and MgO crystallites. Nanometre-sized LiF particles were found to react the most at low temperatures due to their increased structural disorder. Our multimodal characterization points to a Li-promoted densification and sintering mechanism. This impressive reduction in sintering temperature can be harnessed to promote low-temperature fabrication of MgO-based composites for technological applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Sinter formation during directed energy deposition of titanium alloy powders

During directed energy deposition (DED) additive manufacturing, powder agglomeration and sintering can occur outside of the melt pool when using titanium alloy powders. Using in situ synchrotron radiography we investigate the mechanisms by which sintering of Ti6242 powder occurs around the pool, performing a parametric study to determine the influence of laser power and stage traverse speed on sinter build-up. The results reveal that detrimental sinter can be reduced using a high laser power or increased stage traverse speed, although the latter also reduces deposition layer thickness. The mechanism of sinter formation during DED was determined to be in-flight heating of the powder particles in the laser beam. Calculations of particle heating under the processing conditions explored in this study confirm that powder particles can reasonably exceed 700 °C, the threshold for Ti surface oxide dissolution, and thus the powder is prone to sintering if not incorporated into the melt pool. The build-up of sinter powder layer on deposit surfaces led to lack of fusion pores. To mitigate sinter formation and its detrimental effects on DED component quality, it is essential that the powder delivery spot area is smaller than the melt pool, ensuring most powder lands in the melt pool.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Modeling and Simulation of Advanced Manufacturing Techniques using MOOSE and MALAMUTE

Advanced manufacturing techniques offer increased geometry complexity, energy and material usage efficiency improvements, and an expanded palette of materials as compared to conventional manufacturing approaches. Advanced-manufacturing-produced parts can experience wide variations in the final microstructure, and these microstructure variations significantly impact the parts’ performance. In this chapter, we present recent code developments within Multiphysics Object-Oriented Simulation Environment (MOOSE) and in the MOOSE Application Library for Advanced Manufacturing UTilitiEs (MALAMUTE). Here we demonstrate applying these modeling and simulation codes to two advanced manufacturing process types: advanced sintering techniques and laser-based additive manufacturing techniques. The multiphysics and multiscale capabilities of these codes enable prediction of the microstructure evolution resulting from variations in the Advanced manufacturing process parameters.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Aerosol jet printed 3 omega sensors for thermal conductivity measurement

The 3 omega (3ω) method is a trusted technique for measuring thermal conductivity—a fundamental material property of critical importance in a broad range of applications. However, traditional 3ω sensor processing requires some form of physical vapor deposition, such as metal evaporation or sputtering. These 3ω sensor deposition techniques limit the materials and sample sizes applicable to the 3ω method. This work demonstrates an aerosol jet printing method to directly print silver 3ω sensors that yield accurate temperature-dependent measurement up to 300 °C on materials with thermal conductivity ranging from 1 to 150 W/m K. The interrelationship between printed sensor geometry, sensor thermal stability, and applicability to the 3ω method is examined. Thermal conductivity measurement with 3ω sensors conventionally sintered at 300 °C agrees to independent laser flash measurement within 4% from room temperature to 150 °C. An unconventional rapid high-temperature sintering method is shown to produce sensors that agree within 3% of the laser flash measurements from room temperature to 300 °C. The rapid sintering profiles also reduced the sensor–substrate thermal boundary resistance of the printed sensors by as much as 88%. The direct printing of 3ω sensors creates opportunities for measurement of thermal transport properties in applications previously inapplicable to the 3ω method.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Compensating for Sintering Distortion in Additively Manufactured Shaped Charge Liners using Physics-Informed Machine Learning

Copper is a challenging material to process using laser-based additive manufacturing due to its high reflectivity and high thermal conductivity. Sintering-based processes can produce solid copper parts without the processing challenges and defects associated with laser melting; however, sintering can also cause distortion in copper parts, especially those with thin walls. In this study, we use physics-informed Gaussian process regression to predict and compensate for sintering distortion in thin-walled copper parts produced using a Markforged Metal X bound powder extrusion (BPE) additive manufacturing system. Through experimental characterization and computational simulation of copper’s viscoelastic sintering behavior, we can predict sintering deformation. We can then manufacture, simulate, and test parts with various compensation scaling factors to inform Gaussian process regression and predict a compensated as-printed (pre-sintered) part geometry that produces the desired final (post-sintered) part.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Enhancing thermal conductivity of UO 2 with the addition of UB 2 via conventional sintering techniques

We report that uranium dioxide has been the primary fuel type used in light water reactors for more than 40 years and proven to be reliable and robust. However, the Fukushima-Daiichi nuclear accident has motivated new work evaluating fuels with characteristics promoting accident tolerance, including enhanced thermal conductivity. Recently, additives have been investigated to increase thermal conductivity, but research has been largely focused on non-fissile additions. This study investigated the use of fissile additives to not only increase the thermal conductivity but also increase the uranium loading. Uranium diboride was chosen as the additive for this study due to its promising corrosion behavior as well as its significantly higher thermal conductivity at 573 K (25 Wm -1 K -1 ) when compared to UO 2 (7 Wm -1 K -1 ). Uranium diboride powder was fabricated via the arc melting technique and a ball milling process prior to mixing with UO 2 in a 90/10 wt% UO 2 /UB 2 ratio. Green bodies were made using a uniaxial die and subjected to a traditional pressureless sintering technique at 2073 K in argon. Sintered samples were analyzed via laser flash analysis for thermal diffusivity and differential scanning calorimetry for specific heat capacity in order to calculate thermal conductivity. The samples displayed an increase of 36-55% in thermal conductivity between 323 K and 1273 K when compared to the benchmark samples (pure UO 2 ) as reported in open literature.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS2003

Thermal Conductivity and Stability of HfO2-Y2O3 and La2Zr2O7 Evaluated for 1650 Deg C Thermal/Environmental Barrier Coating Applications

HfO2-Y2O3 and La2Zr2O7 are candidate thermal and environmental barrier coating (T/EBC) materials for gas turbine ceramic matrix composite (CMC) combustor applications because of their relatively low thermal conductivity and high temperature capability. In this paper, thermal conductivity and high temperature stability of hot-pressed and plasma sprayed specimens with representative partially-stabilized and fully-cubic HfO2-Y2O3 compositions and La2Zr2O7 were evaluated at temperatures up to 1700 C using a steady-state laser heat-flux technique. Sintering behavior of the plasmasprayed coatings was determined by monitoring the thermal conductivity increases during a 20-hour test period at various temperatures. Durability and failure mechanisms of the HfO2-Y2O3 and La2Zr2O7 coatings on mullite/SiC hexoloy or SiC/SiC CMC substrates were investigated at 1650 C under thermal gradient cyclic conditions. Coating design and testing issues for the 1650 C thermal/environmental barrier coating applications are also discussed.

Zhu, Dong-Ming↗
NASA NTRS2004

Thermal Conductivity and Water Vapor Stability of Ceramic HfO2-Based Coating Materials

HfO2-Y2O3 and La2Zr2O7 are candidate thermal/environmental barrier coating materials for gas turbine ceramic matrix composite (CMC) combustor liner applications because of their relatively low thermal conductivity and high temperature capability. In this paper, thermal conductivity and high temperature phase stability of plasma-sprayed coatings and/or hot-pressed HfO2-5mol%Y2O3, HfO2-15mol%Y2O3 and La2Zr2O7 were evaluated at temperatures up to 1700 C using a steady-state laser heat-flux technique. Sintering behavior of the plasma-sprayed coatings was determined by monitoring the thermal conductivity increases during a 20-hour test period at various temperatures. Durability and failure mechanisms of the HfO2-Y2O3 and La2Zr2O7 coatings on mullite/SiC Hexoloy or CMC substrates were investigated at 1650 C under thermal gradient cyclic conditions. Coating design and testing issues for the 1650 C thermal/environmental barrier coating applications will also be discussed.

Zhu, Dong-Ming↗
DOE OSTI2020

Spark plasma sintering (SPS) densified U 3 Si 2 pellets: Microstructure control and enhanced mechanical and oxidation properties

Dense U 3 Si 2 pellets with controlled grain structure and enhanced thermal-mechanical and oxidation properties are synthesized with spark plasma sintering (SPS). Microstructure and phase composition of the SPS densified pellets are characterized systematically using SEM, EDS, and XRD. Thermal-mechanical properties and oxidation behavior of the sintered silicide fuel pellets are analyzed by laser flash, indentation, and dynamic thermogravimetric analysis. Dense U 3 Si 2 pellets are consolidated by combining high energy ball milling and rapid sintering by SPS, and the microstructure structures are controlled from micron-sized (~5.7 μm grain size) for conventional silicide to a nanocrystalline matrix with an average grain size of ~280 nm. A dominant phase of distorted U 3 Si 2 was identified with lattice expansion due to residual thermal stress upon SPS consolidation and rapid cooling processes. Both micron-sized and nano-sized pellets show exceptional thermal transport properties, consistent with monolithic silicides reported in literature. The SPS-densified pellets possess simultaneously high hardness and fracture toughness. The SPS-densified silicide pellets also demonstrate exceptional oxidation performance with extended onset oxidation temperature above 500 °C and reduced oxidation kinetics, particularly for nano-sized pellets. A strong strain effect was proposed in which compressive stress in nano-sized pellets enhances the oxidation resistance of silicide fuels, as evidenced by the degradation of oxidation performance upon strain relaxation by isothermal annealing. The correlation among the sintering process – microstructure control – physical properties and fuel behavior is established. A new concept of strain engineering is proposed further properties optimization, enabling the development of potential oxidation and corrosion-resistant silicides with extended performance, the key technological challenge of U 3 Si 2 as the leading concept of accident tolerant fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1981

Laser processing of silicon solar cells

Results of a study to utilize an Nd:glass laser for production line annealing of ion implantation induced damage in solar cells are reported. Czochralski-grown and sawn Si wafers 7.6 cm in diam, 0.35 mm thick, were implanted with phosphorus junctions and boron BSFs. Annealing with electron beam, laser, and firing of an Al paste to form the BSFs in different cells was compared. The laser was employed at 1.06 and 0.53 micron and in combination of both, with a 20-50 nsec pulsewidth, and energy densities of 1.2, 1.5, 1.9, and 2.1 J/sq cm. Best optical coupling was observed with the combined wavelengths and a 20 nsec pulse, using energy densities less than 1.5 J/sq cm. Although the Al sintered cells displayed the best characteristics, laser annealing is concluded to offer electrically active, defect-free, shallow junction Si substrates for high efficiency cells.

Katzeff, J. S.↗
DOE OSTI2020

Information integrated glass module fabricated by integrated additive and subtractive manufacturing

In this Letter, we report a novel integrated additive and subtractive manufacturing (IASM) method to fabricate an information integrated glass module. After a certain number of glass layers are 3D printed and sintered by direct C O 2 laser irradiation, a microchannel will be fabricated on top of the printed glass by integrated picosecond laser, for intrinsic Fabry–Perot interferometer (IFPI) optical fiber sensor embedment. Then, the glass 3D printing process continues for the realization of bonding between optical fiber and printed glass. Temperature sensing up to 1000°C was demonstrated using the fabricated information integrated module. In addition, the long-term stability of the glass module at 1000°C was conducted. Enhanced sensor structure robustness and harsh temperature sensing capability make this glass module attractive for harsh environment structural health monitoring.

Zhang, Qi (ORCID:0000000268655981)↗
DOE OSTI2021

Application of Refractory High-Entropy Alloys for Higher-Reliability and Higher-Efficiency Brayton Cycles and Advanced Nuclear Reactors

An exceptional set of newly-discovered advanced superalloys known as refractory high-entropy alloys (RHEAs) can provide near-term solutions for wear, erosion, corrosion, high-temperature strength, creep, and radiation issues associated with supercritical carbon dioxide (sCO2) Brayton Cycles and advanced nuclear reactors. In particular, these superalloys can significantly extend their durability, reliability, and thermal efficiency, thereby making them more cost-competitive, safer, and reliable. For this project, it was endeavored to manufacture and test certain RHEAs, to solve technical issues impacting the Brayton Cycle and advanced nuclear reactors. This was achieved by leveraging Sandia’s patents, technical advances, and previous experience working with RHEAs. Herein, three RHEA manufacturing methods were applied: laser engineered net shaping, spark plasma sintering, and spray coating. Two promising RHEAs were selected, HfNbTaZr and MoNbTaVW. To demonstrate their performance, erosion, structural, radiation, and hightemperature experiments were conducted on the RHEAs, stainless steel (SS) 316 L, SS 1020, and Inconel 718 test coupons, as well as bench-top components. The experimental data is presented, analyzed, and confirms the superior performance of the HfNbTaZr and MoNbTaVW RHEAs vs. SS 316 L, SS 1020, and Inconel 718. In addition, to gain more insights for larger-scale RHEA applications, the erosion and structural capabilities for the two RHEAs were simulated and compared with the experimental data. The experimental data confirm the superior performance of the HfNbTaZr and MoNbTaVW RHEAs vs. SS and Inconel. Most importantly, the erosion and the coating material experimental data show that erosion in sCO2 Brayton Cycles can be eliminated completely if RHEAs are used. The experimental suite and validations confirm that HfNbTaZr is suitable for harsh environments that do not include nuclear radiation, while MoNbTaVW is suitable for harsh environments that include radiation.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Fabrication and thermophysical properties of UO 2 -UB 2 and UO 2 -UB 4 composites sintered via spark plasma sintering

Uranium dioxide (UO 2 ) composites with uranium diboride (UB 2 ) and uranium tetraboride (UB 4 ) have been proposed as advanced fuel candidates due to their high thermal conductivity, high melting point, high fissile density and their ability to incorporate a built-in burnable poison by tailoring the targeted 10 B/ 11 B ratio. As such, it is important to assess the fabrication, and thermal and micromechanical properties of such composites. In this work, UO 2 -UB 2 and UO 2 -UB 4 samples with boride phase fractions of 5, 15 and 30 wt% were fabricated to high densities (above 95 % theoretical density) via spark plasma sintering (SPS). This enabled sintering at relatively low temperatures and short timescales. SPS also aided in maintaining the target phase fractions of the samples as reactions between the constituent phases were suppressed due to the short timescales and reducing environment during sintering. Here, thermal diffusivity measurements from 299 to 1273 K were conducted through laser flash analysis (LFA). The diffusivity increased as a function of boride weight fraction, and UB 2 additions increased the thermal diffusivity of the composites more than UB 4 additions. Assessment of the LFA results indicated in-situ reactions between the UO 2 and boride phases that suppress the thermal diffusivity occur above 800 K for all samples. Oxidation of the boride phase was proposed as the underlying reaction. This was supported by thermodynamic assessments from the literature, as well as microstructural, crystallographic, and nanoindentation characterization performed on these samples.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Heat Exchanger Intensification Through Powder Processing and Enhanced Design (HIPPED)

High intensity, supercritical CO 2 heat exchangers capable of operating at temperatures between 800 and 1100 ˚C and pressures greater than 80 bar are considered a critical component for high efficiency power generation and a range of next-generation industrial processes. A novel heat exchanger concept was proposed in this project. The proposed concept involved a plate-type architecture with three-dimensional fins, called twisted s-shaped fins, that capitalize on additive manufacturing. Four manufacturing processes were studied to realize the complex envisioned design: press and sinter of metallic powders, directed energy deposition, laser powder bed fusion, and a novel powder bed process involving a photoreactive polymer called SEAM (scalable expeditious additive manufacturing), that later was developed at MSU. The team was able to manufacture subscale heat exchangers using laser powder bed fusion (LPBF) and SEAM. The team settled on using SEAM as a final manufacturing approach due to its very low cost. The SEAM-manufactured heat exchanger, however, when tested under pressure, exhibited leaks and the process still requires further development beyond the timeline of the project. To support the heat exchanger design and testing, the team developed a new high temperature flow loop allowing testing under high temperature and pressure. Computational modeling of the heat exchanger was also performed for the twisted s-shaped fins and the computations were validated with experimental data. The new twisted fins resulted in enhanced heat transfer and reduced pressure drop. To further minimize pressure drop in the plate heat exchanger, the team also developed a simplified model for flow maldistribution in the manifolds, providing a new tool for designers that eliminates the need for complex CFD calculations. A technoeconomic analysis was also developed to contrast SEAM with LPBF, this tool indicated that SEAM is several times less costly and offer significant promises as a rapid low cost additive manufacturing process for metallic systems.

30 DIRECT ENERGY CONVERSION↗
NASA NTRS2002

Thermal Conductivity and Sintering Behavior of Advanced Thermal Barrier Coatings

Advanced thermal barrier coatings, having significantly reduced long-term thermal conductivities, are being developed using an approach that emphasizes real-time monitoring of thermal conductivity under conditions that are engine-like in terms of temperatures and heat fluxes. This is in contrast to the traditional approach where coatings are initially optimized in terms of furnace and burner rig durability with subsequent measurement in the as-processed or furnace-sintered condition. The present work establishes a laser high-heat-flux test as the basis for evaluating advanced plasma-sprayed and physical vapor-deposited thermal barrier coatings under the NASA Ultra Efficient Engine Technology (UEET) Program. The candidate coating materials for this program are novel thermal barrier coatings that are found to have significantly reduced thermal conductivities due to an oxide-defect-cluster design. Critical issues for designing advanced low conductivity coatings with improved coating durability are also discussed.

Zhu, Dongming↗