Search NASA⌕ Search

SEARCH · Search NASA

Results for “lattice engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Nonlinear viscoelastic response of silicone additively manufactured direct ink write (DIW) foams under repetitive compression

To investigate dynamic fatigue behavior of foam in military protective applications, such as helmets, additively manufactured (AM) foams were compressively strained into the plateau region using a reduced design of experiments. A simple power law was found to govern the decline in dynamic stiffness (complex modulus) as the foams underwent the purchase order requirement of 10,000 cycles of small deformation in the plateau region. This rate of decline was newly found to correlate with the degree of nonlinearity in the material’s deformation, quantified using total harmonic distortion. Materials with low nonlinearity exhibited relatively stable stiffness across cycles, while those with high nonlinearity experienced greater losses. The observed nonlinearity depended on both applied stress and strain rate. A strong linear correlation (R 2 = 0.78) was identified between second-order nonlinearity and the time-dependent stiffness response. Two lattice structures were examined: face-centered tetragonal (FCT) and simple cubic (SC). The SC material exhibited higher total harmonic distortion (5%) and lower stiffness retention than the FCT (2%). In conclusion, these results suggest that for cyclic compression applications in a wide variety of industries such as packaging, personal protective equipment, or aerospace, selecting materials with lower stress and greater structural uniformity can enhance the stability of dynamic performance.

42 ENGINEERING↗
DOE OSTI2023

Deep learning-enhanced design for functionally graded auxetic lattices

Auxetic materials with counterintuitive negative Poisson’s ratio have been of significant interest due to potential applications across diverse engineering fields. Functionally grading such auxetics further enables customization of the structural response and harnesses the potential for multi-functional applications. However, a critical challenge in designing functionally graded lattices is to efficiently determine the spatial variation of the functional gradient and the corresponding geometric designs to achieve the desired response. In this paper, a highly efficient deep learning-based inverse design framework for functionally graded tetra-petal auxetics with spatially tailored properties is presented. This framework significantly improves the efficiency of tailoring functionally graded auxetics where many unit cells need to be tailor-designed. The graded tetra-petal auxetics obtained from the inverse design framework are additively manufactured and subjected to impact tests. The results show superior impact performance compared with uniform designs, demonstrating the effectiveness of the proposed inverse design framework, which can be inspirable to promote advanced structures/materials with enhanced impact resistance.

42 ENGINEERING↗
DOE OSTI2021

Long-Range Dipole–Dipole Interactions in a Plasmonic Lattice

Spontaneous emission of quantum emitters can be enhanced by increasing the local density of optical states, whereas engineering dipole-dipole interactions requires modifying the two-point spectral density function. Here, we experimentally demonstrate long-range dipole-dipole interactions (DDIs) mediated by surface lattice resonances in a plasmonic nanoparticle lattice. Using angle-resolved spectral measurements and fluorescence lifetime studies, we show that unique nanophotonic modes mediate long-range DDI between donor and acceptor molecules. We observe significant and persistent DDI strengths for a range of densities that map to similar to 800 nm mean nearest-neighbor separation distance between donor and acceptor dipoles, a factor of similar to 100 larger than free space. Here, our results pave the way to engineer and control long-range DDIs between an ensemble of emitters at room temperature.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2023

Dipole ladders with large Hubbard interaction in a moiré exciton lattice

Two-dimensional semiconductor moiré superlattices have emerged as a powerful platform for engineering correlated electronic phenomena. On the other hand, optical excitation creates charge neutral interlayer excitons with an out-of-plane electric dipole. Strong onsite dipole–dipole interaction promises the formation of correlated bosonic states, akin to the Mott states of electrons, but has not yet been demonstrated. Here we report a large interaction between excitons occupying the same moiré lattice site—characterized by the Hubbard U parameter—and consequent dipole ladders with spin- and electron-filling dependence in WSe 2 /WS 2 moiré superlattices. Photoluminescence measurements show successive peaks emerging with an energy separation of around 34 meV above the ground state as the exciton density is increased. This corresponds to the sequential injection of excitons into a single site with an energy cost to overcome the large exciton Hubbard U, forming a dipole ladder. Based on findings of local magnetic moments at two holes per moiré cell, we show that excitons can also fill a second moiré orbital, establishing the two-orbital nature of the moiré potential landscape. Our results show that the Bose–Hubbard model with possible exciton crystal phases can be investigated in interacting opto-moiré quantum matter.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Single-Particle Insights Into the Electronic Structure and Enhanced Stability of CsPbBr 3 /FAPbBr 3 Core/Crown Nanoplatelets at the Nanometer Scale

Colloidal perovskite nanoplatelets (NPLs), despite their exceptional optoelectronic properties, face significant challenges due to their intrinsic instability and trap-assisted non-radiative recombination. Although many studies employing surface engineering, such as selecting ligands or coating to passivate defects, have demonstrated improved optoelectronic properties, these enhancements are typically inferred from bulk-ensemble measurements; the effects at the single-particle level remain elusive. Here, we conduct single-particle-level studies using scanning tunneling spectroscopy (STS) on a unique core–crown system, CsPbBr 3 @FAPbBr 3 NPLs, where the lateral surfaces of the CsPbBr 3 core are coated with an FAPbBr 3 crown. Experimental density-of-states (DOS) analysis reveals a 47% reduction in deep-trap states in core-crown NPLs compared to core-only NPLs, consistent with nearly two-fold enhancements in photoluminescence quantum yields. Progressive I–V sweep measurements demonstrate superior electrical stability in core-crown NPLs, preserving band structure with minimal degradation, while core-only NPLs exhibit rapid bandgap shrinkage and trap formation. Density functional theory (DFT) calculations indicate that FA incorporation distorts Pb octahedral lattice, widening the bandgap. This study elucidates how surface engineering modulates charge localization, passivates defects, and enhances stability at the single-particle level. Moreover, by uncovering bias-induced trap states in single unpassivated NPLs, this study establishes a precise, robust approach for characterizing emerging perovskite nanocrystals.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2024

Systems and methods for thermal barrier coatings to modify engine component thermal characteristics

An engine component comprises one or more thermal barrier coatings applied to one or more areas of the engine component. The thermal barrier coatings reduce the temperature rate of change of the areas to which the thermal barrier coating is applied. Reducing the temperature rate of change can help reduce lattice structure damage caused by different temperatures in different areas of the engine component. The thermal barrier coating can be applied as a monolithic layer on a surface of the engine component or can be applied in different areas using patterns. The patterns allow for the tuning of the performance characteristics (temperature rate of change) of the areas of the engine component and can help reduce defect propagation, such as cracks, in the thermal barrier coating from one area of the thermal barrier coating to other areas of the thermal barrier coating.

Koci, Chad Palmer↗
DOE OSTI2026

Machine learning inversion of interatomic force constants from single-crystal inelastic neutron scattering

Atomic vibrations govern many macroscopic properties of materials, but experiments to comprehensively probe them remain challenging. Inelastic neutron scattering (INS) is a powerful technique to map phonon dispersions in crystals, especially when leveraging modern time-of-flight (ToF) spectrometers with large detectors. However, efficiently and robustly extracting interatomic force constants (FCs) parameterizing phonon dynamics from experimental spectra remains a bottleneck due to the complexity and high dimensionality of ToF INS datasets. Here, we present a machine learning approach for the direct inversion of FCs from single-crystal INS measurements. The framework leverages synthetic training data generated using universal machine-learned force fields and an efficient physics-based forward model. We benchmark two neural architectures–one emphasizing structured latent representation learning and the other direct, supervised spectral regression–across simulated datasets for two materials under idealized and noisy conditions. The latent-representation model is subsequently applied to experimental single-crystal INS data on germanium. The model is shown to reproduce FCs derived from both first-principles simulations and from iterative optimization, and furthermore achieves reliable inference even from sparse, single-orientation measurements representing short data acquisitions. Analysis of the learned latent space reveals semantically continuous and physically interpretable encodings that support strong cross-domain generalization. By bridging theoretical and experimental domains, we establish a path toward rapid inversion of experimental spectra and data-driven interpretation of temperature-dependent lattice dynamics.

42 ENGINEERING↗
DOE OSTI2021

Designed and biologically active protein lattices

Versatile methods to organize proteins in space are required to enable complex biomaterials, engineered biomolecular scaffolds, cell-free biology, and hybrid nanoscale systems. Here, we demonstrate how the tailored encapsulation of proteins in DNA-based voxels can be combined with programmable assembly that directs these voxels into biologically functional protein arrays with prescribed and ordered two-dimensional (2D) and three-dimensional (3D) organizations. We apply the presented concept to ferritin, an iron storage protein, and its iron-free analog, apoferritin, in order to form single-layers, double-layers, as well as several types of 3D protein lattices. Our study demonstrates that internal voxel design and inter-voxel encoding can be effectively employed to create protein lattices with designed organization, as confirmed by in situ X-ray scattering and cryo-electron microscopy 3D imaging. The assembled protein arrays maintain structural stability and biological activity in environments relevant for protein functionality. The framework design of the arrays then allows small molecules to access the ferritins and their iron cores and convert them into apoferritin arrays through the release of iron ions. The presented study introduces a platform approach for creating bio-active protein-containing ordered nanomaterials with desired 2D and 3D organizations.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2022

Slip velocity boundary conditions for the lattice Boltzmann modeling of microchannel flows

Abstract Slip flows in ducts are important in numerous engineering applications, most notably in microchannel flows. Compared to the standard no‐slip Dirichlet condition, the case of slip formulates as a Robin‐type condition for the fluid tangential velocity. Such an increase in mathematical complexity is accompanied by a more challenging numerical transcription. The present work concerns with this topic, addressing the modeling of the slip velocity boundary condition in the lattice Boltzmann method (LBM) applied to steady slow viscous flows inside ducts of nontrivial shapes. As novelty, we extend the newly revised local second‐order boundary (LSOB) Dirichlet fluid flow method [ Philos. Trans. R. Soc. A 378, 20190404 (2020)] to implement the slip velocity condition within the two‐relaxation‐time (TRT) framework. The LSOB follows an in‐node philosophy where its operation principle seeks to explicitly reconstruct the unknown boundary populations in the form of a third‐order accurate Chapman–Enskog expansion, where the wall slip condition is built‐in as a normal Taylor‐type condition. The key point of this approach is that the required first‐ and second‐order momentum derivatives, rather than computed through nonlocal finite difference approximations, are locally determined through a simple local linear algebra procedure, whose formulation is particularly aided by the TRT symmetry argument. To express the obtained derivatives, two approaches are considered, called and , which operate with node and wall variables, respectively. These two formulations are developed to prescribe the physical slip condition over plane and curved walls, including the corners. Their consistency and accuracy characteristics are examined against alternative linkwise strategies to impose the wall slip velocity, such as the kinetic‐based diffusive bounce‐back scheme, the central linear interpolation slip scheme, and the multireflection slip scheme. The several slip schemes are tested over different 3D microchannel configurations, with walls not conforming with the LBM uniform mesh. Numerical tests confirm the advanced accuracy characteristics of the proposed LSOB slip boundary scheme, revealing the added challenge of the wall slip modeling, and that parabolic accuracy is a necessary requirement to reach second‐order accuracy within this problem class.

Silva, Goncalo↗
DOE OSTI2026

Astigmatism-free 3D optical tweezer control for rapid atom rearrangement

Reconfigurable neutral-atom arrays are a promising platform for quantum computing, quantum simulation, and quantum metrology, but atom transport using frequency-chirped acousto-optic deflectors (AODs) is limited by chirp-induced acoustic lensing and trajectory distortion. We address these limitations using a three-dimensional acousto-optic deflector lens (3D-AODL), a design predicted to reduce long-range transport times by more than a factor of two. We further introduce fading-Shepard waveforms that circumvent finite AOD bandwidth, enabling sustained axial displacement. We demonstrate unrestricted three-dimensional optical-tweezer motion over a 200 μm × 200 μm × 136 μm volume with velocities exceeding 4.2 m/s. Arbitrary three-dimensional control of optical-tweezer trajectories enables rapid atom rearrangement and dynamical engineering of optical potentials in tweezer arrays and optical lattices. This capability advances quantum control and atom manipulation in neutral-atom quantum processors by enabling faster rearrangement, higher clock rates, and scalable sorting in complex geometries.

Lu, Yue-Hui [University of California, Berkeley, C↗
DOE OSTI2022

Alphavirus Particles Can Assemble with an Alternate Triangulation Number

Alphaviruses are spherical, enveloped RNA viruses primarily transmitted by mosquitoes, and cause significant arthritogenic and neurotropic disease in humans and livestock. Previous reports have shown that—in contrast to prototypical icosahedral viruses—alphaviruses incorporate frequent defects, and these may serve important functions in the viral life cycle. We confirm the genus-wide pleomorphism in live viral particles and extend our understanding of alphavirus assembly through the discovery of an alternate architecture of Eastern equine encephalitis virus (EEEV) particles. The alternate T = 3 icosahedral architecture differs in triangulation number from the classic T = 4 icosahedral organization that typifies alphaviruses, but the alternate architecture maintains the quasi-equivalence relationship of asymmetric units. The fusion spike glycoproteins are more loosely apposed in the T = 3 form with corresponding changes in the underlying capsid protein lattice. This alternate architecture could potentially be exploited in engineering alphavirus-based particles for delivery of alphaviral or other RNA.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

System, method, and computer program for creating an internal conforming structure

A system for creating an internal formation of a tubular structure having an inner surface via additive manufacturing. The system broadly includes a computer modeling system and an additive manufacturing system. The computer modeling system may include a processor for generating a lattice cellular component via computer-aided design software according to inputs received from a user. The processor may also generate an internal formation lattice structure based on the lattice cellular component and modify the lattice structure to follow and/or conform to the curvature of the inner surface of the outer wall of the tubular structure. The additive manufacturing system may be configured to produce the lattice structure and the tubular structure via additive manufacturing material deposited layer by layer according to the lattice structure.

42 ENGINEERING↗
DOE OSTI2023

High Efficiency Multijunction Devices: Solar Cells, Thermophotovoltaics, LEDs

High-efficiency III-V multijunction solar cells require multiple alloys with optimal bandgaps and excellent material quality. However, many useful alloys are lattice-mismatched to available substrates, and require strain-engineering tricks to enable efficient use. To this extent, we have developed low-dislocation density metamorphic material and optically-thick stress-balanced superlattices, enabling access to a wide variety of III-V alloys. Combined with transparent tunnel junctions, these components allow optimizing multijunction devices for a variety of applications. We have designed multijunction cells for the G173G-terrestrial and AM0-space spectra with record 39.5% and 34.2% efficiency, respectively, and also thermophotovoltaic cells for blackbody spectra that reach over 40% TPV-efficiency. Finally, using these PV components, we demonstrate a multijunction LED with high quantum efficiency.

high-efficiency↗
DOE OSTI2026

Parametric reduced order models for graded lattice structures

Graded lattice structures, characterized by smoothly varying mechanical properties, hold significant promise for optimizing material distribution in advanced engineering applications. However, accurately modeling these structures poses substantial computational challenges due to the continuous geometric variations within their unit cells. Here, to address these challenges, this paper introduces a novel Efficient Reduced Order Model (EROM) that integrates the Matrix Discrete Empirical Interpolation Method (MDEIM) and Discrete Empirical Interpolation Method (DEIM) with polynomial regression to efficiently manage geometric parametrization in lattice structures. Unlike traditional reduced order models (ROMs) that require extensive precomputed libraries for each geometric configuration, our approach enables continuous geometric variations through a flexible algebraic formulation, significantly reducing computational costs while preserving high accuracy. The method constructs projection matrices for individual unit cells that can be efficiently assembled into global systems, leveraging the repetitive nature of lattice structures. Numerical studies demonstrate that our EROM achieves displacement errors below 1% and von Mises stress prediction errors below 4%, coupled with computational speedups exceeding two orders of magnitude compared to full-order simulations. The proposed method's modularity and scalability make it particularly suitable for design optimization and real-time simulation of functionally graded lattice structures, with applications spanning aerospace to biomedical engineering.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Deep level defects and cation sublattice disorder in ZnGeN 2

The III-nitrides have revolutionized lighting technology and power electronics. Expanding the nitride semiconductor family to include the heterovalent ternary nitrides opens up new and exciting opportunities for device design that may help overcome some of the limitations of the binary nitrides as well as new applications. However, the more complex cation sublattice also gives rise to new complexities with both native and extrinsic defects, such as disorder on the cation sublattice. Here, depth-resolved cathodoluminescence spectroscopy and surface photovoltage spectroscopy measurements of defect energy levels in ZnGeN 2 combined with transmission microscopy and crystal lattice diffraction reveal optical signatures of mid-gap states that can be associated with cation sublattice disorder. The energies of these characteristic optical signatures in ZnGeN 2 thin films grown by metal-organic chemical vapor deposition are in good agreement with energy levels predicted by density functional theory for specific thermodynamically stable native point defects. To test the dependence of these defect signatures on crystal atomic composition, we correlated spatially-resolved optical and atomic composition measurements using spatially resolved x-ray photoelectron spectroscopy with systematically varied growth conditions on the same ZnGeN 2 films. The resultant elemental maps versus defect spectral energies and intensities suggest that cation antisite complexes (Zn Ge -Ge Zn ) versus isolated native point defects form preferentially and introduce mid-gap states that dominate electron-hole pair recombination. Complexing of Zn Ge and Ge Zn antisites manifests as disorder in the cation sub-lattice and leads to the formation of wurtzitic ZnGeN 2 as indicated by transmission electron microscopy diffraction patterns and x-ray diffraction (XRD) reciprocal space maps. Furthermore, these findings emphasize the importance of growth conditions to control cation place exchange.

42 ENGINEERING↗
DOE OSTI2022

Strain Engineering: A Pathway for Tunable Functionalities of Perovskite Metal Oxide Films

Perovskite offers a framework that boasts various functionalities and physical properties of interest such as ferroelectricity, magnetic orderings, multiferroicity, superconductivity, semiconductor, and optoelectronic properties owing to their rich compositional diversity. These properties are also uniquely tied to their crystal distortion which is directly affected by lattice strain. Therefore, many important properties of perovskite can be further tuned through strain engineering which can be accomplished by chemical doping or simply element substitution, interface engineering in epitaxial thin films, and special architectures such as nanocomposites. In this review, we focus on and highlight the structure–property relationships of perovskite metal oxide films and elucidate the principles to manipulate the functionalities through different modalities of strain engineering approaches.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Propagation Pattern for Moment Representation of the Lattice Boltzmann Method

A propagation pattern for the moment representation of the regularized lattice Boltzmann method (LBM) in three dimensions is presented. Using effectively lossless compression, the simulation state is stored as a set of moments of the lattice Boltzmann distribution function, instead of the distribution function itself. An efficient cache-aware propagation pattern for this moment representation has the effect of substantially reducing both the storage and memory bandwidth required for LBM simulations. This article extends recent work with the moment representation by expanding the performance analysis on central processing unit (CPU) architectures, considering how boundary conditions are implemented, and demonstrating the effectiveness of the moment representation on a graphics processing unit (GPU) architecture.

42 ENGINEERING↗
DOE OSTI2023

Visualizing Fault Induced Traveling Waves In Medium Voltage Systems

Traveling waves are induced in power systems during most transient events in the grid. These waves travel close to the speed of light in overhead lines and 50% to 60% the speed of light in underground cables. Even though traveling wave-based protection schemes for transmission systems are available commercially, traveling waves in medium voltage distribution networks are still in research space. Compared to transmission system, medium voltage distribution systems contain more reflections and refractions. Thus, visualization is challenging and is critical in locating faults in distribution network. To address this visualization challenge, this paper presents an open-source tool to visualize the traveling waves using Bewley lattice approach. The developed visualization tool will be useful for the protection engineers to detect and triangulate fault locations in the medium voltage systems and isolate the faults.

Bewley Lattice↗