Search NASA⌕ Search

SEARCH · Search NASA

Results for “limit loads”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

DC-10 composite vertical stabilizer ground test program

A review of the structural configuration and ground test program is presented. Particular emphasis is placed on the testing of a full-scale stub box test subcomponent and full span ground test unit. The stub box subcomponent was tested in an environmental chamber under ambient, cold/wet, and hot/wet conditions. The test program included design limit static loads, fatigue spectrum loading to approximately two service lifetimes (with and without damage), design limit damage tolerance tests, and a final residual strength test to a structural failure. The first full-scale ground test unit was tested under ambient conditions. The test unit was to have undergone static, fatigue, and damage tolerance tests but a premature structural failure occurred at design limit load during the third limit load test. A failure theory was developed which explains the similarity in types of failure and the large load discrepancy at failure between the two test articles. The theory attributes both failures to high stress concentrations at the edge of the lower rear spar access opening. A second full-scale ground test unit has been modified to incorporate the various changes resulting from the premature failure. The article has been assembled and is active in the test program.

Palmer, J. M., Jr.↗
NASA NTRS2010

Simplification of Fatigue Test Requirements for Damage Tolerance of Composite Interstage Launch Vehicle Hardware

The issue of fatigue loading of structures composed of composite materials is considered in a requirements document that is currently in place for manned launch vehicles. By taking into account the short life of these parts, coupled with design considerations, it is demonstrated that the necessary coupon level fatigue data collapse to a static case. Data from a literature review of past studies that examined compressive fatigue loading after impact and data generated from this experimental study are presented to support this finding. Damage growth, in the form of infrared thermography, was difficult to detect due to rapid degradation of compressive properties once damage growth initiated. Unrealistically high fatigue amplitudes were needed to fail 5 of 15 specimens before 10,000 cycles were reached. Since a typical vehicle structure, such as the Ares I interstage, only experiences a few cycles near limit load, it is concluded that static compression after impact (CAI) strength data will suffice for most launch vehicle structures.

Nettles, A. T.↗
NASA NTRS2002

Structural Efficiency of Stitched Composite Panels with Stiffener Crippling

The structural efficiency of blade-stiffened stitched specimens is compared to determine their weight saving potential if blades were allowed to buckle at less than or equal to design ultimate load. Analytical and experimental results from four configurations of crippling specimens are presented. Specimen skin and blades were held together with through-the-thickness stitches prior to curing. No mechanical fasteners were used for the assembly. Tests were conducted with and without low-speed impact damage. Failure modes are discussed. Finite element and experimental results agree for the response of the structures. For some specimen configurations, improved structural efficiency can be obtained by allowing stiffeners to buckle at design limit load rather than requiring that buckling not occur prior to design ultimate load. A parametric study is presented herein which describes the possible weight savings with this approach.

Jegley, Dawn C.↗
NASA NTRS2011

Linear Quadratic Tracking Design for a Generic Transport Aircraft with Structural Load Constraints

When designing control laws for systems with constraints added to the tracking performance, control allocation methods can be utilized. Control allocations methods are used when there are more command inputs than controlled variables. Constraints that require allocators are such task as; surface saturation limits, structural load limits, drag reduction constraints or actuator failures. Most transport aircraft have many actuated surfaces compared to the three controlled variables (such as angle of attack, roll rate & angle of side slip). To distribute the control effort among the redundant set of actuators a fixed mixer approach can be utilized or online control allocation techniques. The benefit of an online allocator is that constraints can be considered in the design whereas the fixed mixer cannot. However, an online control allocator mixer has a disadvantage of not guaranteeing a surface schedule, which can then produce ill defined loads on the aircraft. The load uncertainty and complexity has prevented some controller designs from using advanced allocation techniques. This paper considers actuator redundancy management for a class of over actuated systems with real-time structural load limits using linear quadratic tracking applied to the generic transport model. A roll maneuver example of an artificial load limit constraint is shown and compared to the same no load limitation maneuver.

Burken, John J.↗
NASA NTRS2019

CHANGO: A Software Tool for Boost Stage Guidance of the Space Launch System Exploration Mission 1

The Day of Launch Initiation Load Update (DOLILU) System is the means by which the Space Launch System (SLS) Vehicle trajectory is designed, verified, and uploaded on the Day of Launch (DOL) in order to ensure a safe flight. Launch vehicles are designed to fly down a narrow angle of attack and sideslip angle corridor in order to keep them within structural load limits. The angle of attack and sideslip angle response to the launch vehicle experiences can vary significantly based upon the winds experienced on the DOL. SLS Boost Stage flight employs an open-loop guidance scheme through Solid Rocket Booster (SRB) separation. In the SLS open-loop scheme, the vehicle will fly a prescribed set of attitudes as a function of the change in altitude since launch. This set of reference attitude values and corresponding altitude reference independent values are designed with ground software using winds measured on the DOL with the goal of minimizing angle of attack and sideslip angle, thereby minimizing related ascent integrated vehicle structural loads. The table of Boost Stage attitude commands as a function of altitude gained since launch is called the chi table. A software tool called CHANGO (Chi Angle Optimizer) designs the Boost Stage chi table which is uploaded to the vehicle’s flight computer and used during ascent by the flight software (FSW). The wind and atmospheric conditions are measured prior to launch and pre-processed to become input to the CHANGO software along with a set of parameters developed in advance of the DOL. CHANGO’s target set consists of the heading and altitude rate at SRB separation determined well before launch by the Program to Optimize Simulated Trajectories (POST). CHANGO consists of a simplified three degree-of-freedom (3-DOF) simulation representing the SLS launch configuration. In general, the launch azimuth is strongly correlated with the heading at SRB separation, and the initial pitchover rate is strongly correlated with the altitude rate at SRB separation. CHANGO uses an adaptation of Powell’s method to vary the initial pitchover rate and launch azimuth to solve a 2-dimentional minimization problem. CHANGO’s trajectory simulation is phase-based, with flight events separating the phases. Each flight phase has different attitude alignment logic. CHANGO’s 3-DOF simulation starts when the vehicle’s thrust-to-weight ratio equals one, and ends at a pre-calculated SRB separation time.

Ahmad, Naeem↗
NASA NTRS2021

Center of Gravity Quasi-Static Load Estimate Using Random Vibration Responses

The quasi-static load (QSL) is often levied on flight hardware structural designers as a requirement. This requirement is verified either by test or analysis with engineers using different approaches to meet this requirement. A commonly used approach is to consider the rms acceleration Center of Gravity (CG) responses of test articles undergoing random vibration tests. The differences between structural engineers and/or test conductors within the space industry exist on how the data obtained from flight hardware random vibration tests are used to estimate QSLs. In this paper, a method to accurately estimate the CG grms from the acceleration power spectral densities with an appropriate sigma value to estimate peak CG accelerations is discussed. Recommendations are made to ensure that the community follows consistent QSL estimation from random vibration test data. The method of estimating the CG acceleration responses may also be used to response limit if the flight hardware responses exceed flight limit loads with margins.

Kolaini, Ali↗
NASA NTRS1998

Design Optimization and Analysis of a Composite Honeycomb Intertank

Intertanks, the structure between tanks of launch vehicles, are prime candidates for weight reduction of rockets. This paper discusses the optimization and detailed analysis of a 96 in (2.44 m) diameter, 77 in (1.85 m) tall intertank. The structure has composite face sheets and an aluminum honeycomb core. The ends taper to a thick built up laminate for a double lap bolted shear joint. It is made in 8 full length panels joined with bonded double lap joints. The nominal load is 4000 lb/in (7 x 10(exp 5) N/m). Optimization is by Genetic Algorithm and minimizes weight by varying C, core thickness, number and orientation of acreage and buildup plies, and the size, number and spacing of bolts. A variety of cases were run with populations up to 2000 and chromosomes as long as 150 bits. Constraints were buckling, face stresses (normal, shear, wrinkling and dimpling, bolt stress, and bolt hole stresses (bearing, net tension, wedge splitting, shear out and tension/shear out). Analysis is by a combination of theoretical solutions and empirical data. After optimization, a series of coupon tests were performed in conjunction with a rigorous analysis involving a variety of finite element models. The analysis and test resulted in several small changes to the optimized design. The intertank has undergone a 250,000 lb (1.1 x 10(exp 6) N) limit load test and been mated with a composite liquid hydrogen tank. The tank/intertank unit is being installed in a test stand where it will see 200 thermal/load cycles. Afterwards the intertank will be demated and loaded in compression to failure.

Finckenor, Jeffrey↗
NASA NTRS2019

Common Probe Design Study and Follow-On Activities

The Common Probe Study was funded by the NASA's Planetary Science Division in the Science Mission Directorate in 2018 to investigate the feasibility of a common aeroshell design for atmospheric probe missions at Venus, Jupiter, Saturn, Uranus, and Neptune. The study involved 4 NASA Centers: Ames Research Center, Goddard Space Flight Center, Langley Research Center, and the Jet Propulsion Laboratory. The common aeroshell design that was studied was a 400 kg, 1.5 m diameter, 45-degree sphere cone shape with a high density heatshield material (Heatshield for Extreme Entry Environments Technology, or HEEET) and a parachute system to extract the descent vehicle. This size of aeroshell could accommodate a descent vehicle of 0.75 m diameter, which could encompass both Tier 1 and Tier 2 science instruments at each of the 5 destinations. Study methodology: First, a notional payload of instruments for each destination was defined based on the top priority measurements indicated by the Planetary Science Decadal Survey. Steep and shallow entry flight path angles (EFPA) were defined for each planet based on qualification and operational g-load limits for current, state-of-the-art instruments. Interplanetary trajectories were then identified that bounded the EFPA range.Next, 3-DoF simulations for entry trajectories were run using the entry state vectors from the interplanetary trajectories. Conical ribbon parachutes were sized based on heatshield separation dynamics. Aero-heating correlations were used to generate stagnation point convective and radiative heat flux profiles. High fidelity thermal response models for various TPS materials were used to size stagnation point thicknesses, with margins based on previous studies. Backshell TPS masses were assumed based on scaled heat fluxes from the heatshield and also from previous mission concepts.Based on these analyses, we have found that the common design is applicable for atmospheric probe missions for 4 out of the 5 destinations. Because of the unique gravity well for Jupiter, the entry environments are more severe resulting in heat loads an order of magnitude higher than for the other destinations.The next step is to determine what follow-on activities NASA should engage in. A questionnaire for the atmospheric probe community has been developed, with a focus on what size of aeroshell should be further analyzed (smaller or same diameter), and what incentives would make using such an aeroshell, if assembled and available, desirable to mission proposers.Preliminary results from this questionnaire will be presented.

Hwang, Helen H.↗
NASA NTRS1999

Design Optimization and Analysis of a Composite Honeycomb Intertank

Intertanks, the structure between tanks of launch vehicles, are prime candidates for weight reduction of rockets. This paper discusses the optimization and detailed follow up analysis and testing of a 96 in. diameter, 77 in. tall intertank. The structure has composite face sheets with an aluminum honeycomb core. The ends taper to a thick built up laminate for a double lap bolted splice joint interface. It is made in 8 full length panels joined with bonded double lap joints. The nominal load is 4000 lb/in. Optimization is by Genetic Algorithm and minimizes weight by varying core thickness, number and orientation of acreage and buildup plies, and the size, number and spacing of bolts. A variety of design cases were run with populations up to 2000 and chromosomes as long as 150 bits. Constraints were buckling; face stresses (normal, shear, wrinkling and dimpling); bolt stress; and bolt hole stresses (bearing, net tension, wedge splitting, shear out and tension/shear out). Analysis is by a combination of elasticity solutions and empirical data. After optimization, a series of coupon tests were performed in conjunction with a rigorous analysis involving a variety of finite element models. This analysis and testing resulted in several small changes to the optimized design. The equation used for hole bearing strength was found to be inadequate, resulting in thicker ends. The core thickness increased 0.05", and potting compound was added in the taper to strengthen the facesheet bond. The intertank has undergone a 250,000 lb limit load test and been mated with a composite liquid hydrogen tank. The tank/intertank unit is being installed in a test stand where it will see 200 thermal/load cycles. Afterwards the intertank will be demated and loaded in compression to failure.

Finckenor, Jeff↗
DOE OSTI2025

Organic Acid-Assisted Thermal Dehalogenation of Halide Salt Nuclear Wastes: From Waste Salts to Borosilicate Glass

Only a handful of high-halide salt waste forms have been demonstrated for vitrification-based immobilization strategies for halide-salt nuclear waste streams (e.g., pyroprocessing wastes, molten salt reactor wastes) and they all have low waste loading potential and most have low chemical durabilities for high-alkali streams. An alternative approach to direct salt immobilization is salt partitioning prior to waste form fabrication and one option for partitioning is halide removal (called dehalogenation). Removing the halogen fraction through dehalogenation can significantly reduce the waste volume required for disposal in the primary waste form. Furthermore, when dehalogenation is performed using organic acids, the dehalogenation reagent can decompose during high-temperature vitrification, reducing waste loading limitations in the waste form. In the current work, different organic acids (i.e., oxalic, formic, acetic, oxamic, and citric) were evaluated for dehalogenation efficiency of a simple chloride salt simulant (7.19% LaCl 3 , 53.77% LiCl, and 39.04% KCl, by mole) and a more complex chloride salt simulant called ERV3 (electrorefiner version 3) at 150 °C–300 °C and using H + /Cl – molar ratios of 1:1, 2:1, and 3:1. Additionally, a borosilicate glass waste form called TARS (or the average of refined specifications) was formulated, produced, and characterized for dehalogenated ERV3.

Amorphous materials↗
DOE OSTI2026

Structural Origins of High MoO 3 Solubility in Peraluminous Borosilicate Glasses

Molybdenum (Mo) imposes strict loading limits in conventional borosilicate nuclear waste glasses due to the tendency of tetrahedral molybdate [MoO 4 ] 2− species to phase-separate and crystallize as alkali molybdates. Here, we demonstrate an unprecedented 13.96 wt % (7.51 mol %) MoO 3 solubility in peraluminous sodium aluminoborosilicate glasses a ∼15× increase over their peralkaline counterparts. Using Raman spectroscopy, multinuclear and dipolarcorrelation magic angle spinning nuclear magnetic resonance (MAS NMR), electron paramagnetic resonance (EPR), and scanning transmission electron microscopy (STEM)-energy dispersive spectroscopy (EDS), we reveal that Nadeficient, low optical basicity conditions stabilize octahedral MoO 6 units, which polymerize into molybdite-like Mo−O clusters dispersed within the glass matrix. These Mo-rich clusters suppress the formation of depolymerized [MoO 4 ] 2− environments typically responsible for Na 2 MoO 4 precipitation and instead promote the formation of Na 2 Mo 2 O 7 as the saturation phase. Concurrently, Mo solubility drives the conversion of AlO 4 − to higher-coordination AlO 5 species, liberating Na + that is subsequently sequestered in molybdate-rich domains. The combined evolution of Mo coordination, modifier redistribution, and network depolymerization provides a mechanistic basis for the markedly enhanced Mo solubility in peraluminous compositions. These findings establish new structural guidelines for designing aluminoborosilicate waste forms with substantially greater capacity to incorporate Mo-rich nuclear waste streams.

Amorphous materials↗
DOE OSTI2026

Concerted Proton–Electron Transfer Minimizes Substituent Effects on Adsorbed Phthalocyanine Electrocatalysis

Molecularly modified electrodes (MMEs) are potent electrocatalysts, but few principles exist for their rational design. Electrocatalysis by soluble molecules depends strongly on substituents that tune the catalyst redox potential (E 1/2 ), but it is unclear if this parameter similarly impacts MME catalysis. Herein, we employ the hydrogen evolution reaction (HER) as a test case for comparing carbon-adsorbed cobalt phthalocyanine (CoPc/C) and cobalt hexadecafluoro-phthalocyanine (CoFPc/C). By correlating HER activity and voltammetric data to total Co surface concentration across a wide range of catalyst loadings, we find that only 5–25% of adsorbed Co sites contribute to the Co(II/I) redox wave and that this subpopulation poorly correlates with catalytic activity. Instead, in the low-loading limit, catalytic activity correlates linearly with the majority Co(II/I)-silent Co population, revealing per-site turnover frequency (TOF) values for HER. Despite a 230 mV difference in Co(II/I) redox potentials, CoPc/C and CoFPc/C display TOF values differing by less than a factor of 3 when compared over a wide potential range. Mechanistic studies point to an inner-sphere concerted proton–electron transfer step as rate-determining, suggesting that the Co–H bond dissociation free energy (BDFE) rather than the Co(II/I) E 1/2 is thermodynamically relevant. Computational studies indicate that the fluoro-substituents lead to compensatory changes in Co(II/I) E 1/2 and Co(I) basicity, leaving the Co–H BDFE largely unchanged between CoPc and CoFPc and thereby manifesting in similar catalytic rates. Furthermore, these results highlight the limited effect of E 1/2 -tuning on MME catalytic activity and motivate the development of methods to directly alter active site–substrate BDFE.

Catalysts↗
DOE OSTI2026

Use of Digital Real-Time Simulation and Optimization to Identify Maximum Real Power Injection on Banshee Distribution Network

This study investigates the hosting capacity of the Banshee Distribution Network by optimizing the real power injection at carefully selected Distributed Energy Resource (DER) locations. The analysis is conducted within the framework of power system operational constraints, including bus voltage ranges, thermal line ratings, and transformer loading limits. A Python-based Genetic Algorithm (GA), implemented using the PyGAD library, is employed to iteratively identify the optimal power injection configuration that maximizes network utilization while preserving system reliability. The methodology integrates a real-time simulation environment using the Real-Time Digital Simulator (RTDS), allowing high-fidelity evaluation of power flow and voltage behavior under each proposed injection scenario. By coupling the optimization algorithm with real-time simulation feedback, this approach ensures that both static and dynamic constraints are enforced during the evaluation process. The GA leverages evolutionary operators such as selection, crossover, and mutation to navigate the nonlinear search space efficiently. The results of the study delineate the feasible hosting capacity at three targeted buses, reflecting maximum real power levels that can be injected without causing voltage violations, transformer overloading, or line congestion. These findings provide a decision- support tool for distribution planners and utilities aiming to integrate higher penetrations of DERs in existing infrastructure. Additionally, the work lays the foundation for extending such optimization techniques to multi-objective formulations, including economic dispatch and reactive power coordination, in future studies.

24 POWER TRANSMISSION AND DISTRIBUTION↗
NASA NTRS1972

Improved lip seal for rotating shafts

Sealing efficiency, service life, and seal loading limits of lip seal for rotating shafts are analyzed. Construction of seal and areas of application are described. Specific advantages of improved lip seal over conventional seals are listed.

Endicott, D. L.↗
NASA NTRS1974

Viking Mars lander 1975 dynamic test model/orbiter developmental test model forced vibration test

The Viking Mars Lander 1975 dynamic test model and orbiter developmental test model were subjected to forced vibration sine tests. Flight acceptance (FA) and type approval (TA) test levels were applied to the spacecraft structure in a longitudinal test configuration using a 133,440-N (30,000-lb) force shaker. Testing in the two lateral axes (X, Y) was performed at lower levels using four 667-N (150-lb) force shakers. Forced vibration qualification (TA) test levels were successfully imposed on the spacecraft at frequencies down to 10 Hz. Measured responses showed the same character as analytical predictions, and correlation was reasonably good. Because of control system test tolerances, orbiter primary structure generally did not reach the design load limits attained in earlier static testing. A post-test examination of critical orbiter structure disclosed no apparent damage to the structure as a result of the test environment.

Fortenberry, J.↗
NASA NTRS1975

Design, fabrication, and test of a Graphite/Epoxy Metering Shell (GEMS)

A program to design, fabricate and test a dimensionally stable metering structure in support of the large space telescope (LST) program is discussed. Graphite/epoxy was the material selected as the only viable candidate material which can meet the stringent thermal expansion criteria of the LST. A metering shell was designed and fabricated, with emphasis on dimensional stability in conjunction with low cost. Thermal expansion test coupons extracted from the layups of the skin panels indicated the attainment of a coefficient of thermal expansion of 0.0666 micrometers/m K. Subsequent thermal vacuum chamber tests on the complete metering shell demonstrated an expansion of the 2.95-meter overall length of 0.27 micrometers/K. Static and dynamics tests, which demonstrated adequacy with respect to limit loads and stiffness, were also accomplished.

Source record↗