Search NASA⌕ Search

SEARCH · Search NASA

Results for “line loads”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1997

Arc burst pattern analysis fault detection system

A method and apparatus are provided for detecting an arcing fault on a power line carrying a load current. Parameters indicative of power flow and possible fault events on the line, such as voltage and load current, are monitored and analyzed for an arc burst pattern exhibited by arcing faults in a power system. These arcing faults are detected by identifying bursts of each half-cycle of the fundamental current. Bursts occurring at or near a voltage peak indicate arcing on that phase. Once a faulted phase line is identified, a comparison of the current and voltage reveals whether the fault is located in a downstream direction of power flow toward customers, or upstream toward a generation station. If the fault is located downstream, the line is de-energized, and if located upstream, the line may remain energized to prevent unnecessary power outages.

Russell, B. Don↗
NASA NTRS2004

Airplane Ice Detector Based on a Microwave Transmission Line

An electronic instrument that could detect the potentially dangerous buildup of ice on an airplane wing is undergoing development. The instrument is based on a microwave transmission line configured as a capacitance probe: at selected spots, the transmission-line conductors are partly exposed to allow any ice and/or liquid water present at those spots to act as predominantly capacitive electrical loads on the transmission line. These loads change the input impedance of the transmission line, as measured at a suitable excitation frequency. Thus, it should be possible to infer the presence of ice and/or liquid water from measurements of the input impedance and/or electrical parameters related to the input impedance. The sensory transmission line is of the microstrip type and thus thin enough to be placed on an airplane wing without unduly disturbing airflow in flight. The sensory spots are small areas from which the upper layer of the microstrip has been removed to allow any liquid water or ice on the surface to reach the transmission line. The sensory spots are spaced at nominal open-circuit points, which are at intervals of a half wavelength (in the transmission line, not in air) at the excitation frequency. The excitation frequency used in the experiments has been 1 GHz, for which a half wavelength in the transmission line is .4 in. (.10 cm). The figure depicts a laboratory prototype of the instrument. The impedance-related quantities chosen for use in this version of the instrument are the magnitude and phase of the scattering parameter S11 as manifested in the in-phase (I ) and quadrature (Q) outputs of the phase detector. By careful layout of the transmission line (including the half-wavelength sensor spacing), one can ensure that the amplitude and phase of the input to the phase detector keep shifting in the same direction as ice forms on one or more of the sensor areas. Although only one transmission-line sensor strip is used in the laboratory version, in a practical application, it could be desirable to install multiple strips on different areas to detect localized icing. In that case, a multiplexer should be used to connect the various strips to the phase detector for sequential measurements. Experiments have been performed with freezing and thawing of water and of water/glycol mixtures. The experiments have shown that, whether or not glycol is present, it is possible to distinguish between liquid water and ice via the I and Q outputs; in particular, the equipment can be adjusted so that when water freezes, I decreases and Q increases. With respect to the operation of this instrument, the main effect of glycol is to increase the freezing or thawing time.

Ngo, Phong↗
NASA NTRS1980

Unity power factor converter

A unity power factor converter capable of effecting either inversion (dc-to-dc) or rectification (ac-to-dc), and capable of providing bilateral power control from a DC source (or load) through an AC transmission line to a DC load (or source) for power flow in either direction, is comprised of comparators for comparing the AC current i with an AC signal i.sub.ref (or its phase inversion) derived from the AC ports to generate control signals to operate a switch control circuit for high speed switching to shape the AC current waveform to a sine waveform, and synchronize it in phase and frequency with the AC voltage at the AC ports, by selectively switching the connections to a series inductor as required to increase or decrease the current i.

Wester, Gene W.↗
NASA NTRS1989

Sustained load behavior of graphite/epoxy metal-lined pressure vessels for long-life space applications

Tests were performed on candidate graphite yarns for the overwraps to be used on the Space Station Freedom's pressure vessels. The objective was to determine the performance and ranking of these overwraps to ensure that sustained loads would not be a problem during their 30-yr life in space. Tests were conducted at high stress levels for short time periods on subscale composite bottles. The average delivered fiber stresses were determined from the measured burst pressures via SCI analysis that accounts for both geometry and the properties of the resin and yarn.

Babel, H. W.↗
NASA NTRS2012

Reducing Extra-Terrestrial Excavation Forces with Percussion

High launch costs and mission requirements drive the need for low mass excavators with mobility platforms, which in turn have little traction and excavation reaction capacity in low gravity environments. This presents the need for precursor and long term future missions with low mass robotic mining technology to perform In-Situ Resource Utilization (ISRU) tasks. This paper discusses a series of experiments that investigate the effectiveness of a percussive digging device to reduce excavation loads and thereby the mass of the excavator itself. The goal of percussive excavation is to fluidize dry regolith in front of the leading edge of the tool by mechanically separating the microscopic interlocking grains resulting in a reduced force needed to shear the soil. There are several variables involved with this technique; this experiment varied: Impact energy, frequency, and excavation speed and held constant: impact direction, depth of cut, angle of tool, and soil bulk density. The test apparatus consisted of an aluminum truss bridge with a central pivoting arm. Attached to the arm was a winch with a load cell in line that recorded the tension in the cable and therefore the excavation load. The arm could be adjusted for excavation depth which was recorded along with the arm angle relative to the bridge. A percussive mechanism and 30" wide pivoting bucket were attached at the end of the arm simulating a basic backhoe with a percussion direction tangent to the direction of . movement. Internally the mechanism used a set of die springs and barrel cam to produce the percussive blow. By changing the springs and the speed of the motor the impact energy and frequency of percussion could be varied independently. Impact energies from 11.2J to 30.5J and frequencies from 0 BPM to 700 BPM were investigated. A reduction in excavation force of as much as 51% was achieved in this experimental investigation. Smaller percussive digging implements, tested by others, have achieved a reduction of as much as 72%. This paper will examine the effects of impact energy, frequency, scaling and their effect on excavation forces in a dry granular material such as lunar regolith. The past several years have shown an increasing interest in mining space resources both for exploration and commercial enterprises. This work studied the benefits and risks of percussive excavation and prelimin~ry results indicate that this technique may become an enabling technology for extra-terrestrial excavation of regolith and ice.

Schuler, Jason↗
NASA NTRS1988

Dual-Band Microstrip Antenna With Reactive Loading

Effective but bulky coaxial stub replaced. Short-circuited microstrip transmission line serves as reactive loading element for microstrip antenna. Constructed integrally with stripline radiating element, shorted line preserves low microstrip profile and enables tuning of antenna for two-band operation.

Davidson, Shayla E.↗
NASA NTRS1975

Digital transmitter for data bus communications system

An improved digital transmitter for transmitting serial pulse code modulation (pcm) data at high bit rates over a transmission line is disclosed. When not transmitting, the transmitter features a high output impedance which prevents the transmitter from loading the transmission line. The pcm input is supplied to a logic control circuit which produces two discrete logic level signals which are supplied to an amplifier. The amplifier, which is transformer coupled to the output isolation circuitry, converts the discrete logic level signals to two high current level, ground isolated signals in the secondary windings of the coupling transformer. The latter signals are employed as inputs to the isolation circuitry which includes two series transistor pairs operating into a hybrid transformer functioning to isolate the transmitter circuitry from the transmission line.

Proch, G. E.↗
NASA NTRS2010

Orbital Winch for High-Strength, Space-Survivable Tethers

An Orbital Winch mechanism enables high-load, multi-line tethers to be deployed and retracted without rotating the spool on which the tether is wound. To minimize damage to the tether and the wound package during retraction or deployment under load, it can incorporate a Tension Management Module that reduces the infeed tension by a factor of 15 through the use of a powered capstan with guide rollers. This design eliminates the need for rotating high-voltage electrical connections in tether systems that use propellantless electro-dynamic propulsion. It can also eliminate the need for rotating optical connections in applications where the tether contains optical fibers. This winch design was developed to deploy a 15-km-long, 15-kg high-strength Hoytether structure incorporating conductive wires as part of the MXER-1 demonstration mission concept. Two slewing rings that orbit around the tether spool, combined with translation of one of the slewing rings back and forth along the spool axis to traverse the wind point, enables the winch to wind the tether. Variations of the traverse motion of the slewing ring can accomplish level winds and conical pirn winds. By removing the non-traversing slewing ring, and adding an actuated guide arm, the winch can manage rapid, low-drag deployment of a tether off the end of a pirn-wound spool, followed by controlled retraction and rewinding, in a manner very similar to a spin-casting reel. The winch requires at least two motor driver controller units to coordinate the action of two stepper motors to accomplish tether deployment or retraction.

Hoyt, Robert↗
NASA NTRS1982

Into Mesh Lubrication of Spur Gears with Arbitrary Offset Oil Jet. 2: for Jet Velocities Equal to or Greater than Great Velocity

An analysis was conducted for into mesh oil jet lubrication with an arbitrary offset and inclination angle from the pitch point for the case where the oil jet velocity is equal to or greater than gear pitch line velocity. Equations were developed for minimum and maximum oil jet impingement depth. The analysis also included the minimum oil jet velocity required to impinge on the gear or pinion and the optimum oil jet velocity required to obtain the best lubrication condition of maximum impingement depth and gear cooling. It was shown that the optimum oil jet velocity for best lubrication and cooling is when the oil jet velocity equals the gear pitch line velocity. When the oil jet velocity is slightly greater than the pitch line velocity the loaded side of the driven gear and the unloaded side of the pinion receive the best lubrication and cooling with slightly less impingement depth. As the jet velocity becomes much greater than the pitch line velocity the impingement depth is considerably reduced and may completely miss the pinion.

Akin, L. S.↗
NASA NTRS1994

Magnetocentrifugally driven flows from young stars and disks. 2: Formulation of the dynamical problem

We formulate the dynamical problem of a cool wind centrifugally driven from the magnetic interface of a young star and an adjoining Keplerian disk. We examine the situation for mildly accreting T Tauri stars that rotate slowly as well as rapidly accreting protostars that rotate near break-up. In both cases a wind can be driven from a small X-region just outside the stellar magnetopause, where the field lines assume an open geometry and are rooted to material that rotates at an angular speed equal both to the local Keplerian value and to the stellar angular speed. Assuming axial symmetry for the ideal magnetohydrodynamic flow, which requires us to postpone asking how the (lightly ionized) gas is loaded onto field lines, we can formally integrate all the governing equations analytically except for a partial equation that describes how streamlines spread in the meridional plane. Apart from the difficulty of dealing with PDEs of mixed type, finding the functional forms of the conserved quantities along streamlines - the ratio beta of magnetic field to mass flux, the specific energy H of the fluid in the rotating frame, and the total specific angular momentum J carried in the matter and the field - constitutes a standard difficulty in this kind of (Grad-Shafranov) formalism. Fortunately, because the ratio of the thermal speed of the mass-loss regions to the Keplerian speed of rotation of the interface constitutes a small parameter epsilon, we can attack the overall problem by the method of matched asymptotic expansions. This procedure leads to a natural and systematic technique for obtaining the relevant functional dependences of beta, H, and J. Moreover, we are able to solve analytically for the properties of the flow emergent from the small transsonic region driven by gas pressure without having to specify the detailed form of any of the conserved functions, beta, H, and J. This analytical solution provides inner boundary conditions for the numerical computation in a companion paper by Najita & Shu of the larger region where the main acceleration to terminal speeds occurs.

Shu, Frank H.↗
NASA NTRS1980

The distribution of S II forbidden line emission around Jupiter

Forty-six low-dispersion spectra with high temporal resolution (about 2.5 minutes) are used to investigate the distribution and intensity of the nebular S II forbidden line emission at 6716 and 6731 A around Jupiter. The emission is found to be in the form of a ring in the vicinity of the Jovian magnetic equator with radial limits between four and seven Jovian radii. It is suggested that the ring thickness is quite variable, and that the variation found in intensity with longitude is caused by preferential plasma loading of field lines associated with the Io-induced Jovian decametric bursts.

Pilcher, C. B.↗
NASA NTRS2022

Metrics for Flight Operations: Application to Europa Clipper Tour Selection

Objective measures are ubiquitous in the formulation, design and implementation of deep space missions. Tour durations, flyby altitudes, propellant budgets, power consumption, and other metrics are essential to developing and managing NASA missions. But beyond the simple metrics of cost and workforce, it has been difficult to identify objective, quantitative measures that assist in evaluating choices made during formulation or implementation phases in terms of their impact on flight operations. As part of the development of the Europa Clipper Mission system, a set of operations metrics have been defined along with the necessary design information and software tooling to calculate them. We have applied these methods and metrics to help assess the impact to the flight team on the six options for the Clipper Tour that are currently being vetted for selection in the fall of 2021. To generate these metrics, the Clipper MOS team first designed the set of essential processes by which flight operations will be conducted, using a standard approach and template to identify (among other aspects) timelines for each process, along with their time constraints (e.g., uplinks for sequence execution). Each of the resulting 50 processes is documented in a common format and concurred by stakeholders. Process timelines were converted into generic schedules and workforce-loaded using COTS scheduling software, based on the inputs of the process authors and domain experts. Custom code was generated to create an operations schedule for a specific portion of Clipper's prime mission, with instances of a given process scheduled based on specific timing rules (e.g., process X starts once per week on Thursdays) or relative to mission events (e.g., sequence generation process begins on a Monday, at least three weeks before each Europa closest approach). Over a 5-month period, and for each of six Clipper candidate tours, the result was a 20,000+ line, workforce-loaded schedule that documents all of the process-driven work effort at the level of individual roles, along with a significant portion of the level-of-effort work. Post-processing code calculated the absolute and relative number of work hours during a nominal 5 day / 40 hour work week, the work effort during 2nd and 3rd shift, as well as 1st shift on weekends. The resultant schedules and shift tables were used to generate objective measures that can be related to both human factors and to operational risk and showed that Clipper tours which utilize 6:1 resonant (21.25 day) orbits instead of 4:1 resonant (14.17 day) orbits during the first dozen or so Europa flybys are advantageous to flight operations. A similar approach can be extended to assist missions in more objective assessments of a number of mission issues and trades, including tour selection and spacecraft design for operability.

Sarrel, Marc↗
NASA NTRS2011

Advancements in the Representation of Cloud-Aerosol Microphysics in the GEOS-5 AGCM

Despite numerous challenges, the physical parameterization of cloud-aerosol interactions in atmospheric GCMs has become a top priority for advancement because of our need to simulate and understand past, current, and future indirect effects of aerosols on clouds. The challenges stem from the involvement of wide range of cloud-scale dynamics and aerosol activation physical processes. Cloud dynamics modulate cloud areal extent and condensate, while aerosol activation depends on aerosol mass load, size distribution, internal mixing state, and nucleating properties, and ultimately determines cloud optical properties via particle sizes. Both macro- and micro-scale processes are obviously important for cloud-radiation interactions. We will present the main features of cloud microphysical properties in the GEOS- 5 Atmospheric GCM (AGCM) as simulated by the McRAS-AC (Microphysics of Clouds with Relaxed Arakawa-Schubert and Aerosol-Cloud interaction) scheme. McRAS-AC uses Fountoukis and Nenes (2005) aerosol activation for liquid clouds, and has an option for either Liu and Penner (2005) or Barahona and Nenes (2008, 2009) aerosol activation for ice clouds. Aerosol loading (on-line or climatological) comes from GOCART, with an assumed log-normal size distribution. Other features of McRAS-AC are level-by-level cloud-scale thermodynamics, and Seifert-Beheng (2001)-type precipitation microphysics, particularly from moist convection. Results from Single-Column Model simulations will be shown to demonstrate how cloud radiative properties, lifetimes, and precipitation are influenced by different parameterization assumptions. Corresponding fields from year-long simulations of the full AGCM will also be presented with geographical distributions of cloud effective particle sizes compared to satellite retrievals. While the primary emphasis will be on current climate, simulation results with perturbed aerosol loadings will also be shown to expose the radiative sensitivity of the microphysical parameterization.

Lee, D.↗
NASA NTRS1971

The Effects of Parachute System Mass and Suspension-Line Elastic Properties on the LADT #3 Viking Parachute Inflation Load

Analytical calculations have considered the effects of 1) varying parachute system mass, 2) suspension-line damping, and 3) alternate suspension-line force-elongation data on the canopy force history. Results indicate the canopy force on the LADT #3 parachute did not substantially exceed the recorded vehicle force reading and that the above factors can have significant effects on the canopy force history. Analytical calculations have considered the effects of i) varying parachute system mass, 2) suspension line damping, and 3) different suspension-line force-elongation data on the canopy force history. Based on the results of this study the following conclusions are drawn: Specifically, 1. At the LADT #3 failure time of 1.70 seconds, the canopy force ranged anywhere from 15.7% below to 2.4% above the vehicle force depending upon the model and data used. Therefore, the canopy force did not substantially exceed the recorded vehicle force reading. 2. At a predicted full inflation time of 1.80 seconds the canopy force would be greater than the vehicle force by from 1.1% to 10.6%, again depending upon the model and data used. Generally, 3. At low altitudes, enclosed and apparent air mass can significantly effect the canopy force calculated and should, therefore, not be neglected. 4. The canopy force calculations are sensitive to decelerator physical properties. In this case changes in the damping and/or force-elongation characteristics produced significant changes in the canopy force histories. Accurate prediction of canopy force histories requires accurate inputs in these areas.

Talay, Theodore A.↗
NASA NTRS1979

Simple spline-function equations for fracture mechanics calculations

The paper presents simple spline-function equations for fracture mechanics calculations. A spline function is a sequence of piecewise polynomials of degree n greater than 1 whose coefficients are such that the function and its first n-1 derivatives are continuous. Second-degree spline equations are presented for the compact, three point bend, and crack-line wedge-loaded specimens. Some expressions can be used directly, so that for a cyclic crack propagation test using a compact specimen, the equation given allows the cracklength to be calculated from the slope of the load-displacement curve. For an R-curve test, equations allow the crack length and stress intensity factor to be calculated from the displacement and the displacement ratio.

Orange, T. W.↗
NASA NTRS1980

Application handbook for a Standardized Control Module (SCM) for DC-DC converters, volume 1

The standardized control module (SCM) was developed for application in the buck, boost and buck/boost DC-DC converters. The SCM used multiple feedback loops to provide improved input line and output load regulation, stable feedback control system, good dynamic transient response and adaptive compensation of the control loop for changes in open loop gain and output filter time constraints. The necessary modeling and analysis tools to aid the design engineer in the application of the SCM to DC-DC Converters were developed. The SCM functional block diagram and the different analysis techniques were examined. The average time domain analysis technique was chosen as the basic analytical tool. The power stage transfer functions were developed for the buck, boost and buck/boost converters. The analog signal and digital signal processor transfer functions were developed for the three DC-DC Converter types using the constant on time, constant off time and constant frequency control laws.

Lee, F. C.↗
NASA NTRS1981

Design of Spur Gears for Improved Efficiency

A method to calculate spur gear system loss for a wide range of gear geometries and operating conditions was used to determine design requirements for an efficient gearset. The effects of spur gear size, pitch, ratio, pitch line velocity and load on efficiency were determined. Peak efficiencies were found to be greater for large diameter and fine pitched gears and tare (no-load) losses were found to be significant.

Anderson, N. E.↗
NASA NTRS1981

Design of spur gears for improved efficiency

A method to calculate spur gear system power loss for a wide range of gear geometries and operating conditions is used to determine design requirements for an efficient gearset. The effects of spur gear size, pitch, ratio, pitch-line-velocity and load on efficiency are shown. A design example is given to illustrate how the method is to be applied. In general, peak efficiencies were found to be greater for larger diameter and fine pitched gears and tare (no-load) losses were found to be significant.

Anderson, N. E.↗