SEARCH · Search NASA

Results for “metal impurities”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

All sources NASA NTRS DOE OSTI

DOE OSTI2023

Melt-grown semi-insulating Mn:β-Ga 2 O 3 single crystals exhibiting unique visible absorptions and luminescence

In this study, several acceptor dopants have been explored in β-Ga 2 O 3 to produce semi-insulating substrates and epitaxial films. Fe and Mg make up the majority of research thus far; however, other transition metals provide potential alternatives for optimized performance. β-Ga 2 O 3 bulk single crystals were grown by the Czochralski and vertical gradient freeze methods with a nominal dopant concentration of 0.25 at. % Mn. Ultraviolet-visible-near infrared spectroscopy and photoluminescence revealed polarization- and orientation-dependent optical absorptions (pleochroism) coupled with an orange luminescence. All samples were electrically insulating, on the order of 10 9 –10 11 ohm cm at room temperature, indicative of acceptor doping. Actual dopant concentrations of the intentionally doped transition metal and background impurities were determined via glow discharge mass spectrometry, indicating the macroscale segregation behavior. High-temperature resistivity measurements indicated an experimental acceptor level of 1.7 ± 0.2 eV. Hydrogenation of samples resulted in an increase in the orange luminescence and O–H stretching modes observable in the infrared spectrum. Density functional theory calculations were performed to determine the likely site-occupancy and acceptor level of Mn in the bandgap.

36 MATERIALS SCIENCE↗

NASA NTRS1993

Heat of segregation of single substitutional impurities

The method of Bozzolo, Ferrante and Smith (BFS) is applied for the calculation of the heat of segregation of single substitutional impurities in fcc metals. A simple equation for predicting the heat of segregation is derived for the rigid case (no atomic relaxations). The results of including atomic relaxation using a Monte Carlo method are also presented and the results compared with a number of experimental and theoretical results.

Bozzolo, Guillermo↗

NASA NTRS1996

Kinetics of Static Strain Aging in Polycrystalline NiAl-based Alloys

The kinetics of yield point return have been studied in two NiAl-based alloys as a function of aging time at temperatures between 300 and 700 K. The results indicate that the upper yield stress increment, Delta sigma(sub u) (i.e., stress difference between the upper yield point and the final flow stress achieved during prestraining), in conventional purity (CP-NiAl) and in high purity carbon-doped (NiAl-C) material first increased with a t(exp 2/3) relationship before reaching a plateau. This behavior suggests that a Cottrell locking mechanism is the cause for yield points in NiAl. In addition, positive y-axis intercepts were observed in plots of Delta sigma(sub u) versus t(exp 2/3) suggesting the operation of a Snoek mechanism. Analysis according to the Cottrell Bilby model of atmosphere formation around dislocations yields an activation energy for yield point return in the range 70 to 76 kJ/mol which is comparable to the activation energy for diffusion of interstitial impurities in bcc metals. It is, thus, concluded that the kinetics of static strain aging in NiAl are controlled by the locking of dislocations by Cottrell atmospheres of carbon atoms around dislocations.

Weaver, M. L.↗

DOE OSTI2023

Purification of Lithium-Ion Battery Black Mass through Tailored Alkaline Corrosion

Obtaining high-purity material outputs is crucial to the viability of novel process aimed at direct recycling of lithium-ion batteries. Metallic impurities in recycled cathodes have been shown to inhibit performance, thereby threatening mainstream acceptance of recycled battery products. Thus, shredded black mass (BM) must be purified to remove metallic contaminants, and specifically Al and Cu originating from the electrode current collectors. We herein explore a process to ionize solid copper and aluminum to ionic form based on tailored alkaline chemistry, without incurring damage to the target cathode material (Li(NixMnyCo1-x-y)O2; NMC). Al and Cu corrosion may be enhanced through the addition of chloride salt, elevated temperatures, and the use of ultrasonication - all of which disrupt the formation of passivating films on the metallic surface, and thereby increase corrosion rate. We demonstrate optimized parameters for Al and Cu corrosion both from a kinetic and overall process cost perspective. Further, we analyze the impact of these conditions on the structural (XRD, SEM), chemical (EDS, ICP), and electrochemical (impedance, cycling, dQ/dV) properties of NMC, and suggest that the present purification method does not significantly disrupt NMC performance. Finally, we present preliminary results from a promising bench-scale demonstration of this purification process applied to a simulated black mass.

ADVANCED PROPULSION SYSTEMS,ENERGY STORAGE↗

DOE OSTI2020

Development of metallic nuclear material purification process via simultaneous chlorination and volatilization

Here, a purification process involving simultaneous chlorination and volatilization is reported using aluminum, iron, gallium, and uranium separation from cerium metal as the demonstration system. Anhydrous Cl 2 gas was reacted with the metal after it had been converted to small particles of hydride at temperatures ranging from 523 to 973 K. Each of the impurities should form chlorides with relatively high saturated vapor pressures. The objective of the process was to volatilize these chlorides after first achieving near-complete conversion of the metals to hydride and then chlorides. Complete conversion of hydrides to chlorides could not be achieved using relatively low-grade (99.5%) Cl 2 . High decontamination factors for all of the metal impurities required near complete conversion to chloride. It was concluded that oxygen contamination of the feed gas stream likely limits the conversion to chlorides by forming oxides instead, which then limits the volatilization of contaminants. Uranium was particularly challenging to remove in experiments suspected of having high oxygen contamination in the feed gas stream. After switching to ultra-high purity (99.999%) Cl 2 , complete conversion to chlorides within the measurement error was possible for the entire temperature range studied. Decontamination factors for aluminum, iron, gallium, and uranium were found to have average values of 1.9, 9.8, 14, and 5, respectively, at 973 K. While the process was most extensively studied using a once-through gas flow, recycling unreacted Cl 2 gas succeeded at minimizing waste while still maintaining complete conversion and similar decontamination factors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

HyBlend Collaborative Research Partnership (CRADA Final Report)

This agreement assembles a multi-lab, multi-industry team to address high-priority research topics related to the blending of hydrogen (H2) into the U.S. natural gas (NG) pipeline network. There are four main research objectives: 1. Compatibility of metals (SNL) – Develop general principles for operation of HyBlend™ delivery systems in the context of structural integrity and assess the role of gas impurities on degradation of metal pipelines. 2. Compatibility of polymers (PNNL) – Assess gas impurities in HyBlend for polymer pipeline degradation and lifetime predictions. 3. Life cycle analysis (LCA) (ANL) – Analyze the life cycle of technology pathways for hydrogen and NG blends, as well as alternative pathways. 4.Techno-economic analysis (TEA) (NREL) – Quantify the costs and opportunities for hydrogen production and blending with the NG network, as well as alternative pathways.

08 HYDROGEN↗

DOE OSTI2023

Suppressing Carbon Incorporation in Metal–Organic Chemical Vapor Deposition GaN Using High‐Offcut‐Angled Substrates

Carbon (C) is a common impurity that acts as a compensator within GaN grown via metal–organic chemical vapor deposition (MOCVD). Reducing C in GaN will help reduce the compensation level and provide a route to achieve GaN with reliably low effective doping for high-power device applications. GaN grown with fast growth rates on bulk GaN with various offcut angles via conventional-MOCVD (C-MOCVD) and laser-assisted MOCVD (LA-MOCVD) is compared and analyzed. C-incorporation effects are compared through quantitative secondary-ion mass spectroscopy analysis in GaN grown on GaN substrate with offcut angles of 4° and 0.3° toward m-plane over a wide range of growth rates by C-MOCVD and LA-MOCVD. For both growth techniques investigated, a significant reduction in C-incorporation is observed when a high-offcut-angle (4°) substrate is used as compared to a lower-offcut-angle (0.3°) substrate. Furthermore, with C-MOCVD, at the fastest growth condition investigated (17.26 μm h −1 at 0.3°-offcut, 15.25 μm h −1 at 4°-offcut), a reduction in [C] by 21.2X is observed with an increase in the offcut angle from 0.3° to 4°. A 82.6X reduction in [C] is observed with the similar fast growth condition via LA-MOCVD on GaN with 4° offcut angle (9.78 μm h −1 ) as compared to C-MOCVD at 0.3° offcut angle (17.26 μm h −1 ).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Impurity screening and Friedel oscillations in Floquet-driven two-dimensional metals

We develop a theory for the non-equilibrium screening of a charged impurity in a two-dimensional electron system under a strong time-periodic drive. Our analysis of the time-averaged polarization function and dielectric function reveals that Floquet driving modifies the screened impurity potential in two main regimes. In the weak drive regime, the time-averaged screened potential exhibits unconventional Friedel oscillations with multiple spatial periods contributed by a principal period modulated by higher-order periods, which are due to the emergence of additional Kohn anomalies in the polarization function. In the strong drive regime, the time-averaged impurity potential becomes almost unscreened and does not exhibit Friedel oscillations. Furthermore, this tunable Friedel oscillations is a result of the dynamic gating effect of the time-dependent driving field on the two-dimensional electron system.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2023

Effect of metal fluorides on the corrosion of structural materials in molten LiF-NaF-KF

The corrosion of structural materials in molten fluoride salts is predominantly caused by the presence of impurities in the salt. Here, this study focuses on understanding the corrosion behavior of selected alloys in molten FLiNaK salt with addition of similar quantities of metal fluoride impurities such as CrF 2 , CrF 3 , FeF 2 , FeF 3 , and NiF 2 . The results show that the presence of selected metal fluoride impurities increases the extent of corrosion of the selected alloys in molten FLiNaK salt, with the exact effect depending on the thermodynamic stability of the fluoride impurity added as well as the composition of the structural alloy studied.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Purification of Degraded Aqueous Piperazine by Ion Exchange and Carbon Treating

Amine purification by ion exchange and carbon treating has been performed for decades to maintain low solvent impurity levels in amines used in natural gas sweetening. The use of these purification methods to remove dissolved metal catalysts and other impurities from amines used in post-combustion carbon capture is less well known. This report presents batch experiments testing the equilibrium adsorption of impurities from degraded piperazine (PZ) onto activated carbon and various ion exchange resins. Compared to cationic exchange, anionic exchange was found to better remove catalytic Fe and UV active species, making it a better candidate for large-scale PZ purification. Carbon treating greatly outperforms anion exchange in the removal of UV active species, but the adsorbents’ difference is less pronounced for the removal of other impurities. Equilibrium adsorption was determined by the UV absorption of the PZ solution at 320 nm, and the results will show this may not be an accurate way to determine equilibrium. Further bench-scale experiments comparing ion exchange and carbon treating are necessary before advancing to larger-scale testing.

amine purification↗

DOE OSTI2022

Electrochemical Mitigation of Corrosion in Molten Chloride Salts During CSP Plant Operation

We are designing an electrochemical flow-cell for removal of corrosive impurities from molten chloride salt Gen3 Concentrating Solar Power (CSP) plants during plant operation. Corrosive impurities will inevitably form in molten chloride salts upon exposure to air and moisture. We previously showed that even small amounts of these impurities, especially MgOHCl, will be detrimental in Gen3 CSP plants, necessitating prohibitively expensive containment alloys and frequent replacement of corroded components. Pre-purification of salt with Mg metal at temperatures above 650 degrees C is the current method for removing corrosive impurities from chloride salts before they are introduced to CSP systems. However, this is not a suitable method for impurity removal during plant operation. First, this method will produce MgO particulates which will damage plant components. Second, Mg metal is solid at the low temperature point (500 degrees C), so the purification will not proceed at a fast rate. At the high temperature point, Mg is soluble. In this case, fast purification may proceed, but dissolved metal is likely to precipitate out in cold-temperature point components, causing damage. In contrast, our electrochemically driven method allows fast Mg-based purification to proceed at the low temperature point, without formation of harmful particulates and without the risk of Mg metal precipitation. This novel approach is inspired by electrorefining techniques that are widely employed in industrial metallurgy for removal of impurities from metals. Impurities in the incoming molten salt will be reduced to inert MgO at the cathode, which can be removed by periodically washing the cell with acid. Simultaneously, Mg dissolution at the anode will ensure salt composition is maintained, with no net removal of Mg2+. We have validated this electrochemical approach at lab scale under static conditions with batch rectors. Furthermore, we have performed analytical modeling and technoeconomic analysis to produce a preliminary engineering design for the purification flow cell.

CSP↗

DOE OSTI2026

Simultaneous Determination of Halogens and Metals in Waste Plastic Pyrolysis Oil by Inductively Coupled Plasma Mass Spectrometry

A major barrier to integrating pyrolysis-derived oil into conventional refinery technology is the presence of impurities, particularly halogens and metals, that can deactivate catalysts. This study presents a novel, cost-effective approach for the simultaneous analysis of a subset of halogens, metals, nonmetals, and metalloids in complex, industrially relevant distilled pyrolysis oil samples, this was previously achievable only through multiple techniques. Excellent results were obtained using a widely accessible inductively coupled plasma mass spectrometry (ICP-MS) method with helium gas mode and standard laboratory consumables, enabling high-throughput analysis and efficient evaluation of adsorbent performance. Sample preparation is straightforward, requiring only dilution in a compatible matrix, and provides accurate and precise quantification, with 75%–137% spike recovery for Be, Ti, V, Cr, Fe, Ni, Co, Cu, As, Se, Mo, Cd, Sb, Tl, and Pb, and 62%–65% spike recovery for Cl and 109%–133% spike recovery for Br. Additionally, an enhanced version of the method using ICP-MS/MS and hydrogen gas is described, which has higher accuracy with 69%–112% spike recovery for Be, B, Ti, V, Fe, Co, Ni, Cu, As, Se, Mo, Cd, Sb, Tl, and Pb, with 85%–102% spike recovery for Cl and 63%–93% spike recovery for Br. Helium mode detection limits for industrially relevant elements (V, Fe, Ni, Cu, As, and Pb) are less than 1.7 µg/kg, and less than 0.2 mg/kg for Br and Cl. Furthermore, this methodology facilitates rapid systematic evaluation of adsorption capacities of materials under time-on-stream conditions and supports robust comparisons across diverse operating environments.

Lazarcik, James [University of Wisconsin-Madison, ↗

DOE OSTI2020

Probing unintentional Fe impurity incorporation in MOCVD homoepitaxy GaN: Toward GaN vertical power devices

Unintentional impurity incorporation in GaN drift layers represents a challenging issue that can limit their potential performance in vertical power devices. In this paper, we focus on studying the origins of Fe impurity incorporation in metal-organic chemical vapor deposition (MOCVD) grown GaN materials. Acting as a compensator in n-type GaN drift layers, Fe impurities can reduce the electron mobility in GaN and limit the lowest controllable doping level. Two sources, the sample cleaning process and growth susceptor, were identified as the main mechanisms of Fe incorporation in the MOCVD GaN growth process. It was found that solvent cleaning of the wafer can introduce significant Fe contamination at the growth interface, which would slowly be incorporated into the GaN epilayer, thus causing background Fe impurity as high as 10 17 cm -3 level. Moreover, the Fe impurity in the coating material on the susceptor can introduce additional Fe impurity during the growth process. Our studies revealed that the Fe impurity level could be significantly suppressed by more than two orders when an alternative cleaning process was used and the susceptor surface was fully covered by substrates. Characterization of the Fe impurity concentrations was performed via secondary ion mass spectrometry. The trap level (E C - 0.57) eV from deep-level transient spectroscopy that had previously been attributed to Fe confirmed the carrier compensation effect from Fe. Room temperature Hall mobility as high as 1007 cm 2 /V s was achieved on the MOCVD grown low-Fe GaN. Results from this work will provide guidance for achieving high purity GaN toward high performance GaN vertical power devices.

42 ENGINEERING↗

DOE OSTI2020

Quantitative defect analysis in MOCVD GaN-on-GaN using cathodoluminescence

Cathodoluminescence (CL) is used as a quantitative characterization technique to probe impurities at the metal-organic chemical vapor deposition (MOCVD) grown GaN-on-GaN homoepitaxial interfaces. CL intensity contrast shows a strong correlation with the interfacial impurity concentrations. Based on the analysis of recombination mechanisms of electron beam induced non-equilibrium carriers, an analytical model is proposed to quantitatively determine the impurity concentrations from CL intensity. The extracted interfacial impurity concentrations from the analytical model show a good agreement with the compensation levels obtained from capacitance-voltage measurement, signifying the potential of CL for probing the quantitative impurity levels in GaN-on-GaN structures. This approach can also be extended to be applied in other material systems.

Chen, Zhaoying↗

DOE OSTI2021

Effect of Li metal addition on corrosion control of Hastelloy N and stainless steel 316H in molten LiF-NaF-KF

Molten fluoride salts are used in various energy harvesting applications such as solar collectors and molten salt nuclear reactors (MSRs). Thermodynamically driven selective dissolution of alloying elements due to impurities present within the fluoride salts have been identified to be the main corrosion mechanism for structural alloys in molten fluoride salts. Impurities in these salts, during salt preparation as well as during operation, can be difficult to control. One way to prevent the selective dissolution of active alloying elements is to make the molten salt reducing by either purifying it to remove impurities or to add some reactive metal that will react with the impurities and make the salt reducing. Here this study is focused on the corrosion behaviour of Hastelloy N and 316H stainless steel in molten LiF-NaF-KF eutectic mixture (FLiNaK) at 700°C and how this behaviour changes with the addition of Li metal as a reducing impurity. Our results indicate that the active metal addition like Li can be very effective in controlling the redox behaviour of salt, which in-turn can mitigate corrosion. Even the addition of small quantities of Li metal can mitigate the selective dissolution of active alloying elements for the tested structural materials in FLiNaK. Our results also suggest that the presence of excess amounts of Li, above the minimum concentration required to react with the impurities in FLiNaK, does not have any detrimental effect in terms of formation of new intermetallic phases at the surface of the selected alloys under tested conditions.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Predictive Models and Novel Accelerated Tests for the Reliability of Cell Metallization in Photovoltaic Modules (Final Report)

Studies of metallization corrosion m photovoltaics have mainly been limited to comparisons of modules placed in accelerated chambers to fielded modules [1]. Damp Heat accelerated tests and phenomenological equations [2] are used to assess metallization corrosion without understanding the effect of UV light and temperature and humidity cycles on encapsulant adhesion degradation. The roles of encapsulant in-and out-diffusions of moisture and encapsulant impurities are important. Furthermore, few photovoltaic metallization corrosion studies included the role of bias and leakage currents, which are crucial in the electrochemical reaction of metallization. Leakage currents can highly accelerate the corrosion mechanism and are important to include in the studies of corrosion. In our research plan, we will address the following gaps in the PV community's understanding of metallization corrosion: (1) metallization corrosion with bias, humidity, and impurities in the encapsulant or metallization; (2) humidity diffusion through fresh and degraded encapsulants; and (3) comparison of model predictions with outdoor field modules and SunPower's extensive data for its back-contact and front-contact fleets [2] along with NREL's store of >20 year old modules. Our goal is to build models and accelerated tests to predict long term degradation of metallization corrosion of photovoltaic modules in the field. Our studies will include metals used in c-Si solar cells (Cu, Ag, and Al) and commonly used encapsulants (EV A (ethylene vinyl acetate), TPO (thermoplastic olefin), and silicone).

14 SOLAR ENERGY↗

DOE OSTI2021

Modeling Induction Stirring and Particle Tracking in Molten Uranium

Two independent numerical models have been developed to simulate the behavior of carbon impurities in molten uranium metal. Informed by experimental parameters, one model was created using the commercial software Star-CCM+ and compared with another developed using open-source codes, including OpenFOAM, Finite Element Method Magnetics (FEMM) and a First Passage Kinetic Monte Carlo (FPKMC) approach. The target experimental system features a 404g uranium metal charge containing an average carbon concentration of 139 ppm which was melted in a vacuum induction furnace at 1400° C then resolidified. The microstructures of the uranium and its impurities before and after melting have been characterized and reported separately. Prior to simulating the uranium-carbon system described, the numerical models were validated using a previously published nonradioactive experimental system to ensure agreement with expected output values. Focus has been placed on modeling velocity fields under induction stirring and impurity particle trajectories.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

Turbulence-Driven Edge-Localized-Mode-Free High-Confinement Mode with Divertor Detachment in a Metal-Wall Tokamak

We report the first demonstration of a minute-scale, edge-localized-mode-free high-confinement plasma regime compatible with divertor partial detachment and enhanced pedestal performance in a metal-wall tokamak, the Experimental Advanced Superconducting Tokamak. This regime is enabled by a newly identified mechanism: during divertor partial detachment, reduced ionization and enhanced pumping in a closed divertor lead to less cooling of the pedestal by recycling neutrals and seeding impurities, resulting in an increased pedestal temperature gradient, which excites high-frequency broadband turbulence. Gyrokinetic simulations identify the high-frequency broadband turbulence as a temperature-gradient-driven trapped electron mode (𝜂 𝑒 -TEM), which drives outward transport of particles and heat, thereby maintaining the edge-localized-mode-free state. This pedestal regime is particularly promising for the International Thermonuclear Experimental Reactor, where the anticipated lower density gradient, reduced E×B shear, and lower collisionality in the pedestal will further facilitate 𝜂 𝑒 -TEM excitation. The achieved integrated scenario with a detached divertor and turbulence-dominated pedestal thus offers a compelling solution for managing heat loads and metal impurity sources for long-pulse high-performance operation in future fusion reactors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗