Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure meshing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

138 records · Page 8

In situ imaging during compression of plastic bonded explosives for damage modeling

Here, the microstructure of plastic bonded explosives (PBXs) is known to influence behavior during mechanical deformation, but characterizing the microstructure can be challenging. For example, the explosive crystals and binder in formulations such as PBX 9501 do not have sufficient X-ray contrast to obtain three-dimensional data by in situ, absorption contrast imaging. To address this difficulty, we have formulated a series of PBXs using octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX) crystals and low-density binder systems. The binders were hydroxyl-terminated polybutadiene (HTPB) or glycidyl azide polymer (GAP) cured with a commercial blend of acrylic monomers/oligomers. The binder density is approximately half of the HMX, allowing for excellent contrast using in situ X-ray computed tomography (CT) imaging. The samples were imaged during unaxial compression using micro-scale CT in an interrupted in situ modality. The rigidity of the binder was observed to significantly influence fracture, crystal-binder delamination, and flow. Additionally, 2D slices from the segmented 3D images were meshed for finite element simulation of the mesoscale response. At low stiffness, the binder and crystal do not delaminate and the crystals move with the material flow; at high stiffness, marked delamination is noted between the crystals and the binder, leading to very different mechanical properties. Initial model results exhibit qualitatively similar delamination.

36 MATERIALS SCIENCE↗

Characterizing Biomass Feedstock Transport Properties Using State of the Art Imaging and Computational Techniques

The microstructure of lignocellulosic biomass determines heat and mass transfer during conversion processes. We present a novel method for characterizing the transport properties of biomass using advanced imaging and computational techniques. The microstructure of two woody feedstocks, red oak and Douglas fir, before and after pyrolysis, is revealed using X-ray computed tomography (XCT). Transport properties are calculated from the XCT images, and principal permeability tensors are calculated using an immersed boundary-based finite volume solver to model gas flow through the geometries. We observe that the permeabilities of native biomass are distinctly anisotropic, however, this anisotropy is greatly reduced after pyrolysis.

adaptive mesh refinement↗

Low-Cost Proton Conducting Membranes for PEM Fuel Cells

Proton exchange membrane (PEM) is the key component in PEM fuel cells that critically determines the system performance and its economic viability. Presently, the state-of-the-art PEMs, such as Nafion membranes, are based on perfluorosulfonic acid (PFSA) ionomers. But these ionomer materials are expensive, particularly at the low volumes that will be needed for initial commercialization. Besides, they are not suitable for fuel cells operated beyond 100°C, because of the limitations connected to the humidification requirement of such membrane materials, limiting the maximum operating temperature to about 90°C. Fuel cells for transportation applications are required to operate in a wide temperature range from –20°C to 120°C. Low-cost PEMs with capabilities in a range of temperature and humidity conditions are urgently needed to meet the DOE fuel cell targets for transportation applications. Amsen Technologies LLC chooses to address the DOE call with a novel reinforced PEM approach based on new, non-PFSA proton conducting ionomers developed from our previous DOE SBIR projects. Along with this approach is the use of very cheap, ultra thin and highly porous microporous polymer meshes as the support for the membrane. The new PEM is expected to have significant cost advantages over traditional PEMs. The microporous polyolefin support costs $2-3/m 2 ; and the new ionomers that Amsen has developed are estimated at ~$\$$250/kg at the higher end including material costs and labor costs (which may go down in the future as the processing is optimized and production scaled up). These have led to an estimate of total material cost for the membrane at $\$$11 to $\$$12/m 2 , offering high potential of meeting the DOE cost targets (≤$\$$20/m 2 ) after adding processing cost and profit margin. The Phase I results have successfully demonstrated that it is very promising to develop the intended low-cost, high-performance PEM membrane. Suitable material system has been identified, and suitable process for forming the new PEM has been developed. Uniform membranes have been reproducibly fabricated. These membranes have been extensively characterized and evaluated in terms of microstructural features, and relevant physical and chemical properties including proton conductivity and area specific proton resistance in a range of temperature and humidity conditions, resistance to electronic conduction, water uptake/swelling, dimensional stability, chemical stability, and mechanical durability. Membrane electrode assemblies (MEA) with the new membrane have been successfully prepared and tested for fuel cell operation. The new PEM showed higher proton conductivity than Nafion membranes for all measurement conditions used in Phase I. With high proton conductivity and ultra-thin thickness (~20 /m), the new membrane showed high promise to met DOE targets for the low ASR. The ASR targets have been met for relatively high RH but not yet for RH ≤ 70%. Further optimization in ionomer chemistry and membrane processing is needed in order to meet the ASR targets for a wide range of temperature and humidity conditions. The new membrane showed fairly high electronic resistance at 1373 ohm cm 2 , meeting the DOE target for electronic resistance (> 1000 ohm cm 2 ). The new membrane also has demonstrated promisingly high chemical stability, high mechanical durability, and high dimensional stability. Fuel cell operation using MEAs with the new membrane have shown the same level of fuel cell performance as MEAs with Nafion membranes. Overall, the new membrane has been demonstrated to have high potential of meeting all DOE performance targets for fuel cell applications as well as the cost targets. The manufacturers of PEM fuel cells, PEM electrolyzers, redox flow batteries, and MEA are the end-users and customers of PEMs. For commercialization purpose and potential partnering relations, we have been talking with many such manufacturers. They have responded with extremely high interest in the new PEM being developed in the present technology. Accomplishments so far have laid down a strong base for Amsen to further the development efforts on this new PEM and to pursue commercialization. The near-term future work will be mainly focused on further development and systematical optimization of the material system, processing, and performance of the new membrane; systematical evaluation of the new membrane in terms of all relevant properties including long-term mechanical, chemical, and combined chemical/mechanical durabilities using DOE specified testing protocols; development of production scale-up scheme; and preparation for commercialization.

08 HYDROGEN↗

Development and Validation of MALAMUTE model for Electric Field Assisted Sintering of Structural Materials

Fusion power plant designs feature extreme material performance requirements for structural material candidates. In addition to conventional alloys, more advanced composites and oxide dispersion strengthened (ODS) alloys are being explored, however, achieving the desired microstructures to maximize performance using traditional manufacturing methods can be challenging. The advanced manufacturing (AM) electric field-assisted sintering (EFAS) technique offers improved control over the final microstructure through higher heating and cooling rates and moderate pressures. Modeling and simulation tools show promise in elucidating the process-structure-property-performance (PSPP) correlation for AM-produced parts, including the EFAS process. An inherently multiscale process, the EFAS technique aligns well with the multiscale modeling capability of the open-source Multiphysics Object-Oriented Simulation Environment (MOOSE)[cite]. We present here an electro-thermo-mechanical approach to modeling the EFAS process using the MOOSE Application Library for Advanced Manufacturing UTilitiEs (MALAMUTE) code. Prediction of the field and gradient distributions across the EFAS tooling is required to accurately describe the conditions for the lower-scale microstructural evolution models. In this work we present the MALAMUTE model developed to predict the electrical potential, temperature, and mechanical stress distribution across the EFAS graphite tooling and part at the larger engineering-scale. Validation of the MALAMUTE engineering-scale model is completed using data from experimental densification and pre-densified runs of iron powder via EFAS at 1000oC. These runs were conducted using a Thermal Technology DCS-5 EFAS system. Data collected during the experiment runs include the direct current (DC) supplied to the graphite tooling, the temperature of the graphite tooling as measured with a pyrometer, and the force applied to the top of the graphite tooling stack, and the data were recorded every 10 seconds. Our validation approach used the current and force data from the EFAS run as boundary condition inputs to the MAMALUTE simulation; the temperature data were used to evaluate the MALAMUTE EFAS model prediction. Results of the MALAMUTE simulations are employed to connect the external pyrometer temperature measurement to the temperature profile across the part undergoing consolidation. We investigate the impact of material property variation and mesh deformation on the temperature profile as predicted by MALAMUTE. We conclude by highlighting projects where the MALAMUTE EFAS modeling and simulation capabilities will be used to assist experimental design.

36 - MATERIALS SCIENCE↗

Three-Dimensional Imaging and Numerical Reconstruction of Graphite/Epoxy Composite Microstructure Based on Ultra-High Resolution X-Ray Computed Tomography

A combined experimental and computational study aimed at high-resolution 3D imaging, visualization, and numerical reconstruction of fiber-reinforced polymer microstructures at the fiber length scale is presented. To this end, a sample of graphite/epoxy composite was imaged at sub-micron resolution using a 3D X-ray computed tomography microscope. Next, a novel segmentation algorithm was developed, based on concepts adopted from computer vision and multi-target tracking, to detect and estimate, with high accuracy, the position of individual fibers in a volume of the imaged composite. In the current implementation, the segmentation algorithm was based on Global Nearest Neighbor data-association architecture, a Kalman filter estimator, and several novel algorithms for virtualfiber stitching, smoothing, and overlap removal. The segmentation algorithm was used on a sub-volume of the imaged composite, detecting 508 individual fibers. The segmentation data were qualitatively compared to the tomographic data, demonstrating high accuracy of the numerical reconstruction. Moreover, the data were used to quantify a) the relative distribution of individual-fiber cross sections within the imaged sub-volume, and b) the local fiber misorientation relative to the global fiber axis. Finally, the segmentation data were converted using commercially available finite element (FE) software to generate a detailed FE mesh of the composite volume. The methodology described herein demonstrates the feasibility of realizing an FE-based, virtual-testing framework for graphite/fiber composites at the constituent level.

Czabaj, M. W.↗

Evaluation of the Effect of Burnup Acceleration on UO 2 Microstructure Evolution

Accelerated fuel qualification (AFQ) is a methodology by which new nuclear fuels are developed in an accelerated time frame compared with historical fuel qualification approaches. AFQ generally relies on high-fidelity physics-based modeling and simulation tools to adequately describe fuel performance as well as on revolutionary methods to accelerate burnup accumulation and collect relevant data more quickly. This report summarizes the use of advanced fuel modeling and simulation tools to evaluate microstructures from commercially irradiated fuel and microstructures from proposed MiniFuel irradiations, in which burnup accumulation is accelerated while prototypic temperature conditions are maintained. In this milestone, we used the mesoscale fuel performance code MARMOT to model the evolution of irradiated UO 2 microstructures and their potential restructuring at high burnup. The simulation conditions were informed by BISON models of both commercially irradiated fuel and MiniFuel. A first set of simulations investigated the recrystallization behavior of fully dense microstructures and showed full recrystallization at burnups as low as 52 MWd/kgU at 950°C. However, these simulations did not account for the presence of fission gas bubbles (predicted by BISON). Therefore, a second set of simulations including fission gas bubbles was performed and indicated that at the lowest temperature considered (650°C), the porous UO 2 microstructures have the highest total Gibbs free energies and are likely to recrystallize earlier than higher temperature cases (800 and 950°C), which agrees with high-burnup fuel characterization data. The results also showed that at lower temperature (650°C), the total free energies of the PWR fuel and MiniFuel microstructures are not significantly different. However, at the highest temperature (950°C), MiniFuel microstructures have a lower free energy than that of the PWR fuel microstructure. The competing effects between the temperature-dependent grain nucleation rate and the reduction of the free energy of the microstructure at higher temperature as a result of diffusion indicated that restructuring may occur at even higher temperatures than those considered in this study. In addition to the microstructure evolution modeling efforts, the burnup gradient across a single fuel specimen was also considered. This evaluation was for the VXF-15 position of the High Flux Isotope Reactor (HFIR) using the code suite HFIRCON, which was developed to automate the workflow for evaluating targets and fuel as they are irradiated in HFIR. The burnup gradient evaluation showed a dependence on both the axial and radial locations within the specimen, with a maximum difference of 1.7 between the inner and outermost radial layers. This relationship was further supported by considering the fission product speciation with respect to location within the specimen, which showed a higher concentration of 239 Pu, 240 Pu, and 241 Pu on the outer radial locations of the specimen than the center. The findings of the burnup and speciation evaluation show that some amount of self-shielding is occurring in the specimen when irradiated in the high-flux environment of HFIR; however, this impact is more pronounced for natural uranium when compared to 6% enrichment due to the higher ratio of 238 U in the specimen. Further analyses are required to understand the sensitivity of this gradient to spatial mesh and enrichment of the specimen.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Response and representation of ductile damage under varying shock loading conditions in tantalum

The response of polycrystalline metals, which possess adequate mechanisms for plastic deformation under extreme loading conditions, is often accompanied by the formation of pores within the structure of the material. This large deformation process is broadly identified as progressive with nucleation, growth, coalescence, and failure the physical path taken over very short periods of time. These are well known to be complex processes strongly influenced by microstructure, loading path, and the loading profile, which remains a significant challenge to represent and predict numerically. In the current study, the influence of loading path on the damage evolution in high-purity tantalum is presented. Tantalum samples were shock loaded to three different peak shock stresses using both symmetric impact, and two different composite flyer plate configurations such that upon unloading the three samples displayed nearly identical “pull-back” signals as measured via rear-surface velocimetry. While the “pull-back” signals observed were found to be similar in magnitude, the sample loaded to the highest peak stress nucleated a connected field of ductile fracture which resulted in complete separation, while the two lower peak stresses resulted in incipient damage. The damage evolution in the “soft” recovered tantalum samples was quantified using optical metallography, electron-back-scatter diffraction, and tomography. These experiments are examined numerically through the use of a model for shock-induced porosity evolution during damage. The model is shown to describe the response of the tantalum reasonably well under strongly loaded conditions but less well in the nucleation dominated regime. As a result, numerical results are also presented as a function of computational mesh density and discussed in the context of improved representation of the influence of material structure upon macro-scale models of ductile damage.

36 MATERIALS SCIENCE↗

An Overview of Material Models in the BISON Fuel Performance Code

BISON is a modern finite element-based nuclear fuel performance code that has been under development at Idaho National Laboratory (INL) since 2009. The code is applicable to both steady and transient fuel behavior and supports the use of one-, two-, and three-dimensional meshes. BISON is designed to be a multi-fuels code. Although primarily applied to Light Water Reactor (LWR) fuel to date, the code has been used to analyze TRISO-coated particle fuel and metal fuel in rod and plate form, design and interpret fuel irradiation experiments and investigate novel fuel concepts. Nuclear fuel operates in an extreme environment that induces complex multiphysics phenomena occurring over distances ranging from inter-atomic spacing to meters, and times scales ranging from microseconds to years. To simulate this behavior requires a wide variety of material models which are often complex and nonlinear. Nearly all of the material models currently available in BISON are empirical, using correlations from existing fuel performance codes or material property libraries. Although these models perform adequately under many conditions, they have well-understood limitations. One obvious weakness is that the models are only valid in the domain of the associated experimental data, and extrapolating beyond this domain can result in substantial errors. A further weakness is that these models are often correlated in terms of imprecise quantities, such as burnup. Materials can, for example, reach a given burnup under very different circumstances, leading to very different material behavior. To overcome these weaknesses, efforts are underway with BISON to develop models based on a multi-scale approach, where material behavior is described with a series of interdependent microstructure based models. This paper provides an overview of the material models available in BISON. To keep the scope manageable, only LWR fuel will be considered. The first section focuses on UO{sub 2} fuel, identifying the models generally required and briefly describing those that have been implemented in the code. The second section repeats this approach for Zircaloy cladding. A final section provides examples of areas where multi-scale material modeling has been applied to BISON. BISON is a modern 2D and 3D nuclear fuel performance code that is applicable to multiple fuel forms. A wide variety of complex and nonlinear material models are required to simulate fuel behavior. Focusing on UO{sub 2} fuel and Zircaloy cladding (LWR fuel), the set of empirical models currently implemented in BISON have been reviewed. To overcome some of the deficiencies associated with empirical models, multi-scale material models are being developed. Two multi-scale models that have been used in BISON were reviewed. (authors)

36 MATERIALS SCIENCE↗

Computation of Effective Mechanical Properties and Mechanical Erosion Modeling of TPS Materials

The goal of this presentation is to provide a general overview of the multi-scale modeling formulation to determine if there is additional surface recession in Thermal Protection Systems (TPS) materials as a result of mechanical erosion due to high shear conditions during atmospheric entry. This modeling process is performed at different scales by leveraging two computational frameworks developed at NASA: the Porous Microstructure Analysis (PuMA) software, and the Porous material Analysis Toolbox based on OpenFOAM (PATO). PuMA specializes in computing effective macro-scale material properties by performing material response simulations on 3D digital micro-scale representations of porous micro-structures. The modeling of TPS materials at the micro-scale is essential to understand how they behave as part of a heat shield assembly. The first part of the presentation will detail the implementation of PuMA’s cell-centered finite volume elasticity solver, which allows the computation of macro-scale effective mechanical properties of heterogeneous and anisotropic materials such as fibrous and woven TPS composites. These homogenized mechanical properties are used by PATO’s mechanical erosion model to predict the TPS material’s recession at a larger scale. This work will also provide some examples of multi-scale analysis from the fiber level up to the unit cell. The second part of the presentation will focus on the macro-scale approach to determine if erosion at the heat shield’s surface occurs due to mechanical and thermal loads experienced during atmospheric entry. To accomplish this, a solid mechanics module was integrated within PATO enabling it to model the potential mechanical erosion in three steps: first, after obtaining the effective mechanical properties with PuMA, the implemented stress analysis solver computes the stress and the displacement fields for the TPS material using the wall shear stress tensor, computed using a CFD solver, as boundary conditions; then, regions on the surface where the stress meets the failure criteria are identified; finally, the failed material is removed and the mesh is redistributed accordingly. The outcome is a model capable of predicting the total recession in the material due to surface chemistry and mechanical erosion.

Mechanical Properties↗

Measurement of Transport Properties of Woody Biomass Feedstock Particles Before and After Pyrolysis by Numerical Analysis of X-Ray Tomographic Reconstructions

Lignocellulosic biomass has a complex, species-specific microstructure that governs heat and mass transport during conversion processes. A quantitative understanding of the evolution of pore size and structure is critical to optimize conversion processes for biofuel and bio-based chemical production. Further, improving our understanding of the microstructure of biochar coproduct will accelerate development of its myriad applications. This work quantitatively compares the microstructural features and the anisotropic permeabilities of two woody feedstocks, red oak and Douglas fir, using X-ray computed tomography (XCT) before and after the feedstocks are subjected to pyrolysis. Quantitative analysis of the three-dimensional (3D) reconstructions allows for direct calculations of void fractions, pore size distributions and tortuosity factors. Next, 3D images are imported into an immersed boundary based finite volume solver to simulate gas flow through the porous structure and to directly calculate the principal permeabilities along longitudinal, radial, and tangential directions. The permeabilities of native biomass are seen to differ by three to four orders of magnitude in the different principal directions, but we find that this anisotropy is substantially reduced in the biochar formed during pyrolysis. The quantitative transport properties reported here enhance the ability of pyrolysis simulations to account for feedstock-specific effects and thereby provide a useful touchstone for the biorefining community.

09 BIOMASS FUELS↗

Shock state distributions in porous tantalum and characterization with multipoint velocimetry

Heterogenous materials under shock compression can be expected to reach different shock states throughout the material according to local differences in microstructure and the history of wave propagation. Here, in this work, a compact, multiple-beam focusing optic assembly is used with high-speed velocimetry to interrogate the shock response of porous tantalum films prepared through thermal-spray deposition. The distribution of particle velocities across a shocked interface is compared to results obtained using a set of defocused interferometric beams that sampled the shock response over larger areas. The two methods produced velocity distributions along the shock plateau with the same mean, while a larger variance was measured with narrower beams. The finding was replicated using three-dimensional, mesoscopically resolved hydrodynamics simulations of solid tantalum with a pore structure mimicking statistical attributes of the material and accounting for radial divergence of the beams, with agreement across several impact velocities. Accounting for pore morphology in the simulations was found to be necessary for replicating the rise time of the shock plateau. The validated simulations were then used to show that while the average velocity along the shock plateau could be determined accurately with only a few interferometric beams, accurately determining the width of the velocity distribution, which here was approximately Gaussian, required a beam dimension much smaller than the spatial correlation lengthscale of the velocity field, here by a factor of ∼30×, with implications for the study of other porous materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NEAMS Update: Quarterly Report for October - December 2011

The Advanced Modeling and Simulation Office within the DOE Office of Nuclear Energy (NE) has been charged with revolutionizing the design tools used to build nuclear power plants during the next 10 years. To accomplish this, the DOE has brought together the national laboratories, U.S. universities, and the nuclear energy industry to establish the Nuclear Energy Advanced Modeling and Simulation (NEAMS) Program. The mission of NEAMS is to modernize computer modeling of nuclear energy systems and improve the fidelity and validity of modeling results using contemporary software environments and high-performance computers. NEAMS will create a set of engineering-level codes aimed at designing and analyzing the performance and safety of nuclear power plants and reactor fuels. The truly predictive nature of these codes will be achieved by modeling the governing phenomena at the spatial and temporal scales that dominate the behavior. These codes will be executed within a simulation environment that orchestrates code integration with respect to spatial meshing, computational resources, and execution to give the user a common 'look and feel' for setting up problems and displaying results. NEAMS is building upon a suite of existing simulation tools, including those developed by the federal Scientific Discovery through Advanced Computing and Advanced Simulation and Computing programs. NEAMS also draws upon existing simulation tools for materials and nuclear systems, although many of these are limited in terms of scale, applicability, and portability (their ability to be integrated into contemporary software and hardware architectures). NEAMS investments have directly and indirectly supported additional NE research and development programs, including those devoted to waste repositories, safeguarded separations systems, and long-term storage of used nuclear fuel. NEAMS is organized into two broad efforts, each comprising four elements. The quarterly highlights October-December 2011 are: (1) Version 1.0 of AMP, the fuel assembly performance code, was tested on the JAGUAR supercomputer and released on November 1, 2011, a detailed discussion of this new simulation tool is given; (2) A coolant sub-channel model and a preliminary UO{sub 2} smeared-cracking model were implemented in BISON, the single-pin fuel code, more information on how these models were developed and benchmarked is given; (3) The Object Kinetic Monte Carlo model was implemented to account for nucleation events in meso-scale simulations and a discussion of the significance of this advance is given; (4) The SHARP neutronics module, PROTEUS, was expanded to be applicable to all types of reactors, and a discussion of the importance of PROTEUS is given; (5) A plan has been finalized for integrating the high-fidelity, three-dimensional reactor code SHARP with both the systems-level code RELAP7 and the fuel assembly code AMP. This is a new initiative; (6) Work began to evaluate the applicability of AMP to the problem of dry storage of used fuel and to define a relevant problem to test the applicability; (7) A code to obtain phonon spectra from the force-constant matrix for a crystalline lattice has been completed. This important bridge between subcontinuum and continuum phenomena is discussed; (8) Benchmarking was begun on the meso-scale, finite-element fuels code MARMOT to validate its new variable splitting algorithm; (9) A very computationally demanding simulation of diffusion-driven nucleation of new microstructural features has been completed. An explanation of the difficulty of this simulation is given; (10) Experiments were conducted with deformed steel to validate a crystal plasticity finite-element code for bodycentered cubic iron; (11) The Capability Transfer Roadmap was completed and published as an internal laboratory technical report; (12) The AMP fuel assembly code input generator was integrated into the NEAMS Integrated Computational Environment (NiCE). More details on the planned NEAMS computing environment is given; and (13) The NEAMS program website (neams.energy.gov) is nearly ready to launch.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗