Search NASA⌕ Search

SEARCH · Search NASA

Results for “model comparison”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Achilles and GENIE Model Comparisons Between Quasi-Elastic Proton Exclusive Events in DUNE PRISM ND-LAr

In this study, we analyze simulated CCQE proton exclusive events in DUNE s ND-LAr using Achilles and GENIE Monte Carlo event generators. We generate events using muon neutrino exclusive flux files of DUNE s on-axis and 20m off-axis PRISM positions and compare various kinematics of proton exclusive events between the event generators. Events are further analyzed in categories according to the number of final-state protons. This study was motivated by QE s dominance in statistics for off-axis events over other channels in which off-axis events are very useful for characterizing DUNE s flux. Furthermore, our motivation for comparing results between generators is driven by off-axis QE neutrino spectra peaking below 1 GeV. In this region, many low-energy proton events are produced in which models have been shown to have disagreements.

43 PARTICLE ACCELERATORS↗

Deriving the Infrared Complex Refractive Indices of Organic Powders for Optical Modeling: Comparison of Methods

Identification of solids via infrared reflection spectroscopy requires a spectral library of all solids likely to be encountered. A confounding factor in populating such a spectral library is that the reflectance spectra of solids vary with their form, including particle size, film thickness, and substrate. To reduce the efforts of experimentally constructing such a library, an alternate strategy is to use the wavelength-dependent optical constants, n and k, of a solid to calculate a series of reflectance spectra corresponding to each scenario or morphology. Because most n/k measurements are best performed on mm-sized crystals, however, the challenge of determining the optical constants increases when a solid is only readily available as a powder, as is often the case. Some organic solids, such as caffeine, are both unavailable in large crystals and difficult to press into pellets. In this study, the infrared optical constants, or complex refractive indices, of caffeine were determined using three different methods: single-angle reflectance, infrared spectroscopic ellipsometry, and quantitative absorbance measurements of KBr pellets. The n and k values derived through each method were used to model the hyperspectral imaging reflectance spectrum of a caffeine film on a steel planchet. Over 1,110 – 870 cm-1, the single-angle reflectance-derived n and k had the best correlation with the experimental spectrum. These results suggest different organic solids may require different methods to determine the most accurate infrared complex refractive indices for synthetic spectral libraries.

FTIR, hyperspectral imaging, infrared, infrared (I↗

Measurement–model comparison of stabilized Criegee intermediate and highly oxygenated molecule production in the CLOUD chamber

Abstract. Atmospheric oxidation is an important phenomenon which produces large quantities of low-volatility compounds such as sulfuric acid and oxidized organic compounds. Such species may be involved in the nucleation of particles and enhance their subsequent growth to reach the size of cloud condensation nuclei (CCN). In this study, we investigate α -pinene, the most abundant monoterpene globally, and its oxidation products formed through ozonolysis in the Cosmic Leaving Outdoor Droplets (CLOUD) chamber at CERN(the European Organization for Nuclear Research). By scavenging hydroxyl radicals (OH) with hydrogen (H 2 ), we were able to investigate the formation of highly oxygenated molecules (HOMs) purely driven by ozonolysis and study the oxidation of sulfur dioxide (SO 2 ) driven by stabilized Criegee intermediates (sCIs). We measured the concentrations of HOM and sulfuric acid with a chemical ionization atmospheric-pressure interface time-of-flight (CI-APi-TOF) mass spectrometer and compared the measured concentrations with simulated concentrations calculated with a kinetic model.We found molar yields in the range of 3.5–6.5 % for HOM formation and 22–32 % for the formation of stabilized Criegee intermediates by fitting our model to the measured sulfuric acid concentrations. The simulated time evolution of the ozonolysis products was in good agreement with measured concentrations except that in some of the experiments sulfuric acid formation was faster than simulated. In those experiments the simulated and measured concentrations met when the concentration reached a plateau but the plateau was reached 20–50 min later in the simulations. The results shown here are consistent with the recently published yields for HOM formation from different laboratory experiments. Together with the sCI yields, these results help us to understand atmospheric oxidation processes better and make there action parameters more comprehensive for broader use.

54 ENVIRONMENTAL SCIENCES↗

X-33 Telemetry Best Source Selection, Processing, Display, and Simulation Model Comparison

The X-33 program requires the use of multiple telemetry ground stations to cover the launch, ascent, transition, descent, and approach phases for the flights from Edwards AFB to landings at Dugway Proving Grounds, UT and Malmstrom AFB, MT. This paper will discuss the X-33 telemetry requirements and design, including information on fixed and mobile telemetry systems, best source selection, and support for Range Safety Officers. A best source selection system will be utilized to automatically determine the best source based on the frame synchronization status of the incoming telemetry streams. These systems will be used to select the best source at the landing sites and at NASA Dryden Flight Research Center to determine the overall best source between the launch site, intermediate sites, and landing site sources. The best source at the landing sites will be decommutated to display critical flight safety parameters for the Range Safety Officers. The overall best source will be sent to the Lockheed Martin's Operational Control Center at Edwards AFB for performance monitoring by X-33 program personnel and for monitoring of critical flight safety parameters by the primary Range Safety Officer. The real-time telemetry data (received signal strength, etc.) from each of the primary ground stations will also be compared during each nu'ssion with simulation data generated using the Dynamic Ground Station Analysis software program. An overall assessment of the accuracy of the model will occur after each mission. Acknowledgment: The work described in this paper was NASA supported through cooperative agreement NCC8-115 with Lockheed Martin Skunk Works.

Burkes, Darryl A.↗

3He and BF3 Neutron Detector Pressure Effect and Model Comparison

Paper for SORMA conference Radiation detection systems for homeland security applications must possess the capability of detecting both gamma rays and neutrons. The radiation portal monitor (RPM) systems that are currently deployed use a plastic scintillator for detecting gamma rays and 3He gas-filled proportional counters for detecting neutrons. Proportional counters filled with 3He are the preferred neutron detectors for use in RPMs because 3He has a large neutron cross section, is relatively insensitive to gamma-rays, is neither toxic nor corrosive, can withstand extreme environments, and can be operated at a lower voltage than some of the alternative proportional counters. The amount of 3He required for homeland security and science applications has depleted the world supply and there is no longer enough available to fill the demand. Thus, alternative neutron detectors are being explored. Two possible temporary solutions that could be utilized while a more permanent solution is being identified are reducing the 3He pressure in the proportional counters and using boron trifluoride (BF3) gas-filled proportional counters. Reducing the amount of 3He required in each of the proportional counters would decrease the rate at which 3He is being used, not enough to solve the shortage but perhaps enough to increase the amount of time available to find a working replacement. BF3 is not appropriate for all situations as these detectors are less sensitive than 3He, BF3 gas is corrosive, and a much higher voltage is required than what is used with 3He detectors. Measurements of the neutron detection efficiency of 3He and BF3 as a function of tube pressure were made. The experimental results were also used to validate models of the RPMs.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Bridging Theory with Practice: An Exploratory Study of Visualization Use and Design for Climate Model Comparison

Evaluation methodologies in visualization have mostly focused on how well the tools and techniques cater to the analytical needs of the user. While this is important in determining the effectiveness of the tools and advancing the state-of-the-art in visualization research, a key area that has mostly been overlooked is how well established visualization theories and principles are instantiated in practice. This is especially relevant when domain experts, and not visualization researchers, design visualizations for analysis of their data or for broader dissemination of scientific knowledge. There is very little research on exploring the synergistic capabilities of cross-domain collaboration between domain experts and visualization researchers. To fill this gap, in this paper we describe the results of an exploratory study of climate data visualizations conducted in tight collaboration with a pool of climate scientists. The study analyzes a large set of static climate data visualizations for identifying their shortcomings in terms of visualization design. The outcome of the study is a classification scheme that categorizes the design problems in the form of a descriptive taxonomy. The taxonomy is a first attempt for systematically categorizing the types, causes, and consequences of design problems in visualizations created by domain experts. We demonstrate the use of the taxonomy for a number of purposes, such as, improving the existing climate data visualizations, reflecting on the impact of the problems for enabling domain experts in designing better visualizations, and also learning about the gaps and opportunities for future visualization research. We demonstrate the applicability of our taxonomy through a number of examples and discuss the lessons learnt and implications of our findings.

54 ENVIRONMENTAL SCIENCES↗

Thermodynamics and Kinetics of Refractory Multi-principal Element Alloys: An Experimental and Modeling Comparison

Here, the search for structural alloys capable of ultrahigh temperature performance has led to the exploration of refractory multi-principal element alloys (RMPEAs). In this work, experimental results for solidification segregation and homogenization of two RMPEAs, NbTaTiW and MoNbTaTi, are compared to simulations using the Scheil and DICTRA modules in Thermo-Calc®. Scheil calculations accurately predict the observed solidification segregation, while DICTRA predicts general trends and can provide a minimum time to achieve homogenization at a given temperature.

36 MATERIALS SCIENCE↗

A detailed experimental and modeling comparison of molecular radiative heat loss in a spark-ignition engine

Radiative heat transfer has been chiefly considered negligible in internal combustion engines, except for Diesel engines where soot radiation was recognized as a significant radiative transfer source. Only more recently, detailed simulations have shown that molecular radiation can be substantial as well. In extension to this, molecular radiative heat transfer can reach detectable levels of about 5–10% of the total heat transfer in spark-ignited engines. The broadband radiative nature of the significant emitting molecules, carbon dioxide and water, makes it necessary to address whether radiative trapping plays a substantial role in either total heat loss or energy redistribution within the cylinder. An experimental setup that allows measurements of the infrared emissions at a 2-crank-angle-degree resolution was developed to determine the importance of radiative trapping by carbon dioxide and water. Measurements were conducted in the well-characterized and documented TCC-III engine at the University of Michigan. The engine operated on a stoichiometric propane/air mixture at a speed of 1,300 RPM. Large Eddy Simulations with added line-by-line photon Monte-Carlo simulations of the molecular radiation were an integral part of this study to plan and devise the measurements. Post-processing of the simulation data included an accurate representation of the experimental volume from where infrared signals are collected. Additionally, the experimental data were used for validation of the photon Monte-Carlo simulations. Joint analysis of experimental and simulated spectra allowed quantifying the significance of radiative trapping. Results show the significant role of radiative trapping when predicting radiative heat transfer in the TCC-III engine.

42 ENGINEERING↗

Polycapillary lenses for soft x-ray transmission in ITER: Model, comparison with experiments, and potential application

Measuring Soft X-Ray (SXR) radiation [0.1 keV; 15 keV] in tokamaks is a standard way of extracting valuable information on the particle transport and magnetohydrodynamic activity. Generally, the analysis is performed with detectors positioned close to the plasma for a direct line of sight. A burning plasma, like the ITER deuterium-tritium phase, is too harsh an environment to permit the use of such detectors in close vicinity of the machine. We have thus investigated in this article the possibility of using polycapillary lenses in ITER to transport the SXR information several meters away from the plasma in the complex port-plug geometry.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗