SEARCH · Search NASA
Results for “oxide interfaces”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Nanoscale Analysis of LSM/YSZ Interfaces within Composite Cathodes for Commercial Solid Oxide Fuel Cells
17th International Symposium on Solid Oxide Fuel Cells (SOFC-XVII), Virtual, July 18-23, 2021
Origin of the 2D Electron Gas at the SrTiO 3 Surface
Bulk SrTiO 3 is a well-known band insulator and the most common substrate used in the field of complex oxide heterostructures. Its surface and interface with other oxides, however, have demonstrated a variety of remarkable behaviors distinct from those expected. In this work, using a suite of in situ techniques to monitor both the atomic and electronic structures of the SrTiO 3 (001) surface prior to and during growth, the disappearance and re-appearance of a 2D electron gas (2DEG) is observed after the completion of each SrO and TiO 2 monolayer, respectively. The 2DEG is identified with the TiO 2 double layer present at the initial SrTiO 3 surface, which gives rise to a surface potential and mobile electrons due to vacancies within the TiO 2-x adlayer. Much like the electronic reconstruction discovered in other systems, two atomic planes are required, here supplied by the double layer. The combined in situ scattering/spectroscopy findings resolve a number of longstanding issues associated with complex oxide interfaces, facilitating the employment of atomic-scale defect engineering in oxide electronics.
Oxide– and Silicate–Water Interfaces and Their Roles in Technology and the Environment
Interfacial reactions drive all elemental cycling on Earth and play pivotal roles in human activities such as agriculture, water purification, energy production and storage, environmental contaminant remediation, and nuclear waste repository management. The onset of the 21st century marked the beginning of a more detailed understanding of mineral aqueous interfaces enabled by advances in techniques that use tunable high-flux focused ultrafast laser and X-ray sources to provide near-atomic measurement resolution, as well as by nanofabrication approaches that enable transmission electron microscopy in a liquid cell. This leap into atomic- and nanometer-scale measurements has uncovered scale-dependent phenomena whose reaction thermodynamics, kinetics, and pathways deviate from previous observations made on larger systems. A second key advance is new experimental evidence for what scientists hypothesized but could not test previously, namely, interfacial chemical reactions are frequently driven by “anomalies” or “non-idealities” such as defects, nanoconfinement, and other nontypical chemical structures. Third, progress in computational chemistry has yielded new insights that allow a move beyond simple schematics, leading to a molecular model of these complex interfaces. In combination with surface-sensitive measurements, we have gained knowledge of the interfacial structure and dynamics, including the underlying solid surface and the immediately adjacent water and aqueous ions, enabling a better definition of what constitutes the oxide– and silicate–water interfaces. This critical review discusses how science progresses from understanding ideal solid–water interfaces to more realistic systems, focusing on accomplishments in the last 20 years and identifying challenges and future opportunities for the community to address. Further, we anticipate that the next 20 years will focus on understanding and predicting dynamic transient and reactive structures over greater spatial and temporal ranges as well as systems of greater structural and chemical complexity. Closer collaborations of theoretical and experimental experts across disciplines will continue to be critical to achieving this great aspiration.
On the Structure–Property Relationship of Semi‐Coherent FeCr 2 O 4 /Cr 2 O 3 Spinel/Corundum Interfaces
Abstract Oxide heterointerfaces are extremely common in both natural and artificial composite structures, including corroded structural materials. Often, key properties such as segregation and atomic transport are dictated by the structure of these interfaces. However, despite this critical link, very few heterointerfaces have been studied in any detail at the atomic scale. Here, one important oxide heterointerface is examined, between spinel and corundum, using the chemical system FeCr 2 O 4 /Cr 2 O 3 as a representative and technologically important case. Using atomistic simulation techniques, it is found that the structure, particularly the local chemistry, of the interface depends on the crystal chemistry at the interface. This atomic and chemical structure further impacts important properties such as defect segregation and mass transport. It is found that defects can nucleate at some regions of these interfaces and migrate back and forth across the corundum layer, suggesting high atomic mobility that may be important for the evolution of spinel/corundum composite structures in extreme conditions.
Electron Trapping and Ion Leaching at the Li-Modified Quartz–Water Interface
Electrons and ions at metal oxide-water interfaces have a critical role in many phenomena and applications, thus making their properties of considerable interest. We here investigate the behavior of a lithium impurity at the water interface with Li-doped SiO 2 using hybrid density functional based ab initio molecular dynamics simulations. We find that the excess electron donated by the lithium dopant localizes on a surface silicon atom and is partially solvated at the aqueous interface. While the position of the excess electron does not change during our ~60 ps simulation, the lithium cation diffuses from its initial position in the SiO 2 subsurface toward the interface and eventually leaches out of the oxide surface and becomes solvated by four water molecules, forming an aqueous Li+- electron complex at the interface. The degree of interaction between the localized electron and the lithium ion controls not only the energy level of the excess electron but also the extent of structural distortion and hydrogen-bonding at the interface. The results of our study can be relevant for understanding the initial stages of glass corrosion, where alkali ions are leached from the surface region by interactions with water.
Ultrathin Amorphous Silica Membrane Enhances Proton Transfer across Solid-to-Solid Interfaces of Stacked Metal Oxide Nanolayers while Blocking Oxygen
A large jump of proton transfer rates across solid-to-solid interfaces by inserting an ultrathin amorphous silica layer into stacked metal oxide nanolayers is discovered using electrochemical impedance spectroscopy and Fourier-transform infrared reflection absorption spectroscopy (FT-IRRAS). The triple stacked nanolayers of Co 3 O 4 , SiO 2 , and TiO 2 prepared by atomic layer deposition (ALD) enable a proton flux of 2400 ± 60 s -1 nm -2 (pH 4, room temperature), while a single TiO 2 (5 nm) layer exhibits a threefold lower flux of 830 s -1 nm -2 . Based on FT-IRRAS measurements, this remarkable enhancement is proposed to originate from the sandwiched silica layer forming interfacial SiOTi and SiOCo linkages to TiO 2 and Co 3 O 4 nanolayers, respectively, with the O bridges providing fast H + hopping pathways across the solid-to-solid interfaces. Finally, together with the complete O 2 impermeability of a 2 nm ALD-grown SiO 2 layer, the high flux for proton transport across multi-stack metal oxide layers opens up the integration of incompatible catalytic environments to form functional nanoscale assemblies such as artificial photosystems for CO 2 reduction by H 2 O.
Infrared spectral signatures of interfacial water at TiO 2 –electrolyte interfaces from deep potential molecular dynamics
Vibrational spectroscopy is a powerful tool for probing water at oxide–electrolyte interfaces, but its molecular interpretation can be challenging. Here, we employ deep potential long-range molecular dynamics simulations with layer-resolved spectral analysis to investigate the microscopic origins of the infrared (IR) response of water at the interface with anatase TiO 2 (101), a prototypical oxide surface. The calculated interfacial spectra exhibit characteristic modifications compared to bulk water IR spectra, including enhanced intensities, a red shifted and broadened stretching band, and a higher-frequency shoulder, in qualitative agreement with experiments. Spectral decomposition shows that these signatures originate mainly from the first interfacial water layer, dominated by surface-bound H 2 O at Ti 5C sites, with secondary contributions from the second layer. A moderate salt concentration (0.4 M NaCl) leaves both the interfacial structure and the spectra essentially unchanged, while tuning the pH strongly modulates the spectral intensity. We establish a scaling relation linking the spectral intensity to the surface water dissociation fraction and the dipole moment, both governed by interfacial electric fields. These findings provide a microscopic framework for interpreting IR spectra of oxide–electrolyte interfaces.
Emergent interface vibrational structure of oxide superlattices
As the length scales of materials decrease, the heterogeneities associated with interfaces become almost as important as the surrounding materials. This has led to extensive studies of emergent electronic and magnetic interface properties in superlattices. However, the interfacial vibrations that affect the phonon-mediated properties, such as thermal conductivity, are measured using macroscopic techniques that lack spatial resolution. Although it is accepted that intrinsic phonons change near boundaries, the physical mechanisms and length scales through which interfacial effects influence materials remain unclear. Here we demonstrate the localized vibrational response of interfaces in strontium titanate–calcium titanate superlattices by combining advanced scanning transmission electron microscopy imaging and spectroscopy, density functional theory calculations and ultrafast optical spectroscopy. Structurally diffuse interfaces that bridge the bounding materials are observed and this local structure creates phonon modes that determine the global response of the superlattice once the spacing of the interfaces approaches the phonon spatial extent. Our results provide direct visualization of the progression of the local atomic structure and interface vibrations as they come to determine the vibrational response of an entire superlattice. Direct observation of such local atomic and vibrational phenomena demonstrates that their spatial extent needs to be quantified to understand macroscopic behaviour. Tailoring interfaces, and knowing their local vibrational response, provides a means of pursuing designer solids with emergent infrared and thermal responses.
Selective atomic sieving across metal/oxide interface for super-oxidation resistance
Abstract Surface passivation, a desirable natural consequence during initial oxidation of alloys, is the foundation for functioning of corrosion and oxidation resistant alloys ranging from industrial stainless steel to kitchen utensils. This initial oxidation has been long perceived to vary with crystal facet, however, the underlying mechanism remains elusive. Here, using in situ environmental transmission electron microscopy, we gain atomic details on crystal facet dependent initial oxidation behavior in a model Ni-5Cr alloy. We find the (001) surface shows higher initial oxidation resistance as compared to the (111) surface. We reveal the crystal facet dependent oxidation is related to an interfacial atomic sieving effect, wherein the oxide/metal interface selectively promotes diffusion of certain atomic species. Density functional theory calculations rationalize the oxygen diffusion across Ni(111)/NiO(111) interface, as contrasted with Ni(001)/NiO(111), is enhanced. We unveil that crystal facet with initial fast oxidation rate could conversely switch to a slow steady state oxidation.
Handbook of Molecular Beam Epitaxy of Oxide Materials: Epitaxial Complex Oxide Growth on Semiconductors
This chapter covers the epitaxy of complex oxides on common inorganic semiconductors. The chapter opens with an introduction, motivating the subject and highlighting key general challenges (Section 6.1). We then proceed to describe the general steps of the growth procedure in Section 6.2, which concludes with an overall discussion about trade-offs and expectation management, with an emphasis on the oxide–semiconductor interface. From there, the text describes oxide growth on the common semiconductors, starting with silicon (Section 6.3), where surface reactions and oxidation are the most challenging aspects. Oxide epitaxy on germanium is described in Section 6.4, which is a less challenging oxide growth scheme on semiconductors. Section 6.5 describes oxide epitaxy on gallium arsenide, one of the more challenging schemes, where interface stability and surface preparation pose key challenges. Finally, in Section 6.6, oxide epitaxy on gallium nitride is described, where the lattice mismatch takes the stage as the key challenge. Altogether, this chapter aims to provide the reader with the practical knowledge, tactics and strategies for oxide epitaxy on semiconductors.
Continuity of reaction kinetics across the pressure and materials gaps in CO oxidation on FeO–Pt interfaces
Translating atomic-scale insights from surface science studies of model catalysts to practical powder catalysts remains a persistent challenge in heterogeneous catalysis. Here, in this study, we demonstrate mechanistic continuity across the pressure and materials gaps during CO oxidation at the FeO-Pt interface using in situ microscopy, spectroscopy and computational modelling. Under reaction conditions, coordinatively unsaturated Fe (Fe cus ) sites at the interface enable selective O 2 activation on CO-saturated surfaces, circumventing the CO-poisoning limitation of platinum-group metals. We identify parallel reaction pathways involving the *O 2 -*CO intermediate. Remarkably, activation energies remain consistent at 12-15 kJ mol −1 (0.12-0.16 eV) from ultrahigh vacuum to atmospheric pressures and from FeO/Pt(111) model catalysts to FeO/Pt powder catalysts, validating mechanistic insights derived from surface science studies. Our findings show an example of bridging the long-standing divide between model and practical catalyst systems, establishing an effective approach to capture catalytic behaviours under operational conditions and advancing mechanism-driven catalyst design.
Preventing native oxide formation in niobium thin films through platinum encapsulation
Superconducting transmon qubits are a key technology in quantum computing, with niobium (Nb) widely used due to its favorable superconducting properties and compatibility with scalable fabrication. However, the performance of Nb-based qubits is hindered by two-level systems (TLS), which arise predominantly from native oxide layers at surfaces and interfaces. These oxides and suboxides form rapidly in air and contribute significantly to decoherence by introducing dielectric losses. While various mitigation strategies, including thermal-annealing, chemical-etching, and nitrogen plasma treatment, have been explored, many are challenging to integrate into large-scale manufacturing due to complexity and instability in ambient conditions. In this study, we investigate the structural, chemical, and superconducting properties of room-temperature sputtered Nb thin films grown on sapphire substrates. We focus on a surface protection strategy using noble metal encapsulation with platinum (Pt) to suppress oxides and reduce TLS-related losses. Structural and chemical characterization were performed using X-ray diffraction, X-ray photoelectron spectroscopy, and transmission electron microscopy. Superconducting properties were measured using a physical property measurement system. Results demonstrate that Pt encapsulation effectively suppresses surface oxidation and mitigates its detrimental impact on superconducting performance. In conclusion, this approach offers a promising path toward enhancing the coherence of Nb-based qubits while remaining compatible with scalable-fabrication processes.
Oxophilicity Drives Oxygen Transfer at a Palladium–Silver Interface for Increased CO Oxidation Activity
A single-layer AgO x phase grown on Ag(111) efficiently transfers oxygen to Pd domains at room temperature, rendering the Pd-decorated surface highly reactive toward CO oxidation. Here, oxygen transfer from AgO x to Pd and the surface reactivity toward CO were investigated as a function of the Pd coverage using X-ray photoelectron spectroscopy, surface infrared spectroscopy of adsorbed CO, temperature-programmed reaction spectroscopy, and density functional theory (DFT) calculations. Our results show that all of the oxygen from the AgO x layer (~0.375 monolayer) migrates to the surface of Pd during formation of a nearly complete Pd bilayer at 300 K and that the oxygen coverages generated on Pd increase as the Pd cluster size decreases, reaching values that exceed the oxygen concentration in the AgO x layer by as much as a factor of 2. Experimental measurements and DFT calculations show that preferential binding of oxygen on the edges of the Pd clusters enhances the oxygen coverage on Pd clusters of decreasing size and produces a heterogeneous spatial distribution of oxygen. CO adsorbs in high coverages at 100 K by binding on both the terraces and O-rich edges of the Pd clusters. During subsequent heating, oxidation of the adsorbed CO consumes nearly all of the oxygen that transferred from AgO x to the Pd domains; in contrast, the pure AgO x layer exhibits limited reactivity toward CO adsorbed at 100 K. These results demonstrate that differences in oxophilicity drive facile oxygen transfer from Ag to the edges of Pd nanoclusters and thereby give rise to an efficient pathway for CO oxidation on bimetallic PdAg surfaces. The cooperation between the Pd and Ag domains results in near-interfacial chemistry that may be broadly important in catalysis by bimetallic alloys.
Iridium Surface Oxide Affects the Nafion Interface in Proton-Exchange-Membrane Water Electrolysis
Proton-exchange-membrane water electrolyzer (PEMWE) catalyst layers consist of aggregates of catalyst particles (typically iridium) and ionomer (typically Nafion). Prior work suggests that the oxide form of Ir affects the kinetics of the oxygen-evolution reaction. However, because most catalyst-benchmarking studies are conducted ex situ in liquid electrolytes, it remains unclear how the ionomer is influenced by the catalyst oxide and affects overall cell performance. Using a suite of experimental techniques, we conduct fundamental investigations into model ink (catalyst and ionomer dispersed in solution) and thin-film systems to inform cell-level overpotential analysis as a function of three forms of Ir (metallic Ir m , oxyhydroxide IrOOH, and oxide IrO 2 ). Furthermore, nafion on Ir m has a high degree of phase separation and higher swelling, likely improving the ionic conductivity. Additionally, Nafion binds most strongly to IrOOH, likely yielding reduced kinetic overpotentials. These findings highlight the intricacies of the ionomer/Ir interface and provide insight into all catalyst-layer systems.
A Closer Look at Fe(II) Passivation of Goethite
Our understanding of how Fe(II) reacts with Fe(III) oxides has evolved significantly based on evidence for electron transfer at the oxide-water interface and Fe(II)-catalyzed recrystallization. Recent experiments, as well as computational calculations, further suggest that defects at oxide surfaces can facilitate electron transfer. There is, however, some evidence that these processes cease after continued contact with Fe(II). Here, we explore the sustainability of these processes over longer time frames by measuring whether exposure to Fe(II) inhibits Fe(II)-goethite electron transfer, and whether this inhibition is reversible. To quantify the extent of electron transfer, we used selective isotope labeling with 57Fe Mössbauer spectroscopy. The results revealed that pre-reacting goethite with Fe(II) decreases the extent of electron transfer during subsequent exposures, and that less electron transfer occurs with increasing reaction time. Similarly, X-ray absorption spectroscopy and magnetic circular dichroism suggest that reaction with Fe(II) consumes surface defects and forms a passivation layer, making goethite less susceptible to electron transfer. When Fe(II) is removed by either wet chemical extraction or oxidation, electron transfer is mostly restored, suggesting that inhibition of electron transfer is reversible. Our results show that in environmental systems, which are commonly subjected to transient geochemical fluctuations, electron transfer between Fe(II) and Fe oxides, and processes linked to it, are likely to be relevant beyond just short time scales.
Nickel Interlayer for Improved Silver Complex Inks Metallization in GaAs Photovoltaic Devices
Large areas of III-V photovoltaic panels are essential to supplying operational energy for a growing demand of satellites of strategic importance to the United States military, covering a range of applications. High fabrication costs and low manufacturing throughput are key barriers to meeting the necessary supply, which can in turn jeopardize mission success. At the device level, metallization based on printing of complex metal inks has attracted significant research interest due to its potential to substantially reduce processing costs and increase throughput while achieving electrical performance comparable to those of conventional metallization schemes. For GaAs photovoltaic devices, however, reliable electrical contacting remains challenging due to the formation of an interfacial oxide layer at the metal-semiconductor interface. This oxide barrier severely limits current extraction from the PV absorber, resulting in unacceptably high contact resistance. In this study, we report the introduction of a reactive nickel (Ni) interfacial layer between the silver metal fingers and the GaAs substrate to suppress oxide formation while maintaining a low-resistance electrical interface, and show performance data from fully fabricated GaAs devices incorporating the Ni interlayer. These results demonstrate the potential of reactive Ni ink as an effective interfacial layer for improved electrical contacting in low-cost PV metallization schemes.
Effect of Ambient Organic Acids on the Water Structure at ${\rm TiO}_{2}$ Interfaces
A molecular-level understanding of the effects of ambient organic compounds on the wettability of titanium dioxide ( ${\rm TiO}_{2}$ ) surfaces is relevant to many of its energy-related and environmental applications. Herein, we focus on two common atmospheric carboxylic acids, formic and acetic acid, and characterize their adsorption/ desorption at the aqueous interfaces of anatase and rutile ${\rm TiO}_{2}$ using molecular dynamics with an ab initio deep neural network potential. Our simulations show that these acids prefer to be localized in the interfacial water layers close to the ${\rm TiO}_{2}$ surface where they are stabilized by the interaction/exchange of their acid proton with a surface oxygen, rather than chemisorb at the surface Ti sites by displacing the adsorbed water. Notably, these acids make the surface of anatase hydrophobic, whereas the larger fraction of adsorbed water dissociation can offset their effect on rutile. Furthermore, these results provide a picture where carboxylic acids control the wettability of ${\rm TiO}_{2}$ largely through acid-base chemistry at the interface rather than chemisorption on the oxide surface, a finding that can help improve the design of self-cleaning surfaces and photocatalytic devices.