Search NASA⌕ Search

SEARCH · Search NASA

Results for “performance ratio”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS2007

Water Vapor Profiling From CoSSIR Radiometric Measurements

Previous millimeter-wave radiometry for water vapor profiling, by either airborne or satellite sensors, has been limited to frequencies less than or equal to 183 GHz. The retrievals are generally limited to an altitude range of 0-10 km. The additional measurements at the frequencies of 380.2 plus or minus 0.8, 380.2 plus or minus 1.8, 380.2 plus or minus 3.3, and 380.2 plus or minus 6.2 GHz provided by the new airborne Compact Scanning Submillimeter-wave Imaging Radiometer (CoSSIR) can extend this profiling capability up to an altitude of about 15 km. Furthermore, the retrievals can be performed over both land and water surfaces in the tropics without much difficulty. These properties are demonstrated by recent CoSSIR measurements on board the NASA WB-57 aircraft during CR-AVE in January 2006. Retrievals of water vapor mixing ratio were performed at eight altitude levels of 1, 3, 5, 7, 9, 11, 13, and 15 km from CoSSIR data sets acquired at observational angles of 0 and 53.4 degrees, and the results were compared with other available measurements from the same aircraft and near-concurrent satellites. A comparison of the variations of mixing ratios retrieved from CoSSIR and those derived from the Meteorological Measurement System (MMS) in the aircraft vicinity, along the path of the transit flight on January 14, 2006, appears to show some connection, although the measurements were referring to different altitudes. A very good agreement was found between the collocated values of total precipitable water derived from the CoSSIR-retrieved water vapor profiles and those estimated from TMI (TRMM Microwave Imager)

Wang, J. R.↗
NASA NTRS2001

High Altitude Small Engine Test Techniques at the NASA Glenn Propulsion Systems Lab

A High Altitude Test was performed in the Propulsion Systems Lab (PSL) at the NASA Glenn Research Center using a Pratt and Whitney Canada PW545 jet engine. This engine was tested to develop a highaltitude database on small, high-bypass ratio, engine performance and operability. Industry is interested in the use of high-bypass engines for Uninhabited Aerial Vehicles (UAV's) to perform high altitude surveillance. The tests were a combined effort between Pratt & Whitney Canada (PWC) and NASA Glenn Research Center. A large portion of this test activity was to collect performance data with a highly instrumented low-pressure turbine. Low-pressure turbine aerodynamic performance at low Reynolds numbers was collected and compared to analytical models developed by NASA and PWC. This report describes the test techniques implemented to obtain high accuracy turbine performance data in an altitude test facility, including high accuracy airflow at high altitudes, very low mass flow, and low air temperatures. Major accomplishments from this test activity were to collect accurate and repeatable turbine performance data at high altitudes to within 1 percent. Data were collected at 19,800m, 16,750m, and 13,700m providing documentation of diminishing LPT performance with reductions in Reynolds number in an actual engine flight environment. The test provided a unique database for the development of engine analysis codes to be used for future LPT performance improvements.

Castner, Raymond↗
NASA NTRS2020

Mid Lift-to-Drag Ratio Rigid Vehicle 6-DoF Performance for Human Mars Entry, Descent, and Landing: A Fractional Polynomial Powered Descent Guidance Approach

Defining a feasible vehicle design and mission architecture capable of reliably delivering apayload of 20 metric tons (mt) or more is a great challenge for landing humans on Mars. TheMid Lift-to-Drag Rigid Vehicle (MRV), a rigid decelerator studied in NASA’s Entry, Descent,and Landing Architecture Study (EDLAS), has shown to be a viable vehicle candidate forfuture human Mars missions. As the vehicle concept matures, models of increasing fidelity areadded to the six-degree-of-freedom (6DoF) EDL simulation. This paper presents 6DoFsimulation results using model updates for vehicle mass properties, fineness ratio, andaerodynamic-propulsive interactions. Additionally, an assessment of the Fractional-Polynomial Powered Descent Guidance (FP2DG) performance is presented, and the vehicleperformance is compared with the Tunable Apollo Powered Descent Guidance (TAPDG).Finally, Monte Carlo results of the vehicle design trades are presented.

Johnson, Breanna J.↗
NASA NTRS1974

Performance of a transonic compressor rotor with an aspect ratio of 6.5

The overall and blade-element performances and the aerodynamic design parameters of a transonic rotor with an aspect ratio of 6.5, designed to investigate the effects of aspect ratio on range and performance are presented. The rotor was designed for a total-pressure ratio of 1.53, an efficiency of 0.898, and a weight flow of 67.76 pounds per second.

Reid, L.↗
NASA NTRS1989

Segmented mirror, manufacturing and alignment tolerances (SMMAT)

An attempt is made to define surface errors, and hence wavelength aberrations or optical path differences, due to fabrication and alignment errors of mirror segments. A FORTRAN routine is written to help to understand the relationship between system performance (Strehl ratio, etc.) and manufacturing and alignment errors for Precision Segmented Reflectors and Large Deployable Reflector. The power of having compensation parameters such as piston and tilt responding to errors in position or figure is demonstrated. Compensation can improve performance by two orders of magnitude.

Manhart, P. K.↗
NASA NTRS1991

Design issues for propulsion systems using metallized propellants

Metallized propellants are liquid propellants that contain metal particles. These particles are suspended in a gelled fuel or oxidizer. Aluminum is used as the metal additive. The addition of metal to conventional propellants can increase their specific impulse and their density over conventional propellants, and consequently, the payload delivered on Mars and lunar transportation vehicles, Earth-to-Orbit vehicles and upper stages for robotic planetary missions. Gelled fuels also provide increased safety during accidental propellant leakage or spills. To take full advantage of these potential performance increases, there are changes that must be made to the vehicle design. The differences are discussed between metallized propellant and traditional liquid propellants and their effect on the propulsion system design. These differences include the propellant density, mixture ratio, engine performance, and propellant rheology. Missions related to the Space Exploration Initiative are considered as design examples to illustrate these issues.

Palaszewski, Bryan↗
NASA NTRS1991

Design issues for propulsion systems using metallized propellants

Metallized propellants are liquid propellants that contain metal particles. These particles are suspended in a gelled fuel or oxidizer. Aluminum is used as the metal additive. The addition of metal to conventional propellants can increase their specific impulse and their density over conventional propellants, and consequently, the payload delivered on Mars and lunar transportation vehicles, Earth-to-Orbit vehicles and upper stages for robotic planetary missions. Gelled fuels also provide increased safety during accidental propellant leakage or spills. To take full advantage of these potential performance increases, there are changes that must be made to the vehicle design. The differences are discussed between metallized propellant and traditional liquid propellants and their effect on the propulsion system design. These differences include the propellant density, mixture ratio, engine performance, and propellant rheology. Missions related to the Space Exploration Initiative are considered as design examples to illustrate these issues.

Palaszewski, Bryan↗
NASA NTRS1976

Performance of a 1.57 pressure-ratio transonic fan stage with a screen-induced 90 deg circumferential inlet flow distortion

A transonic fan stage having a design pressure ratio of 1.57 was tested with a 90 degree circumferential distortion imposed on the inlet flow. The rotor diameter was approximately 50.8 cm, and the design pressure ratio was 1.60 at a tip speed of 425 m/sec. Overall performance at 70 and 100 percent of design speed showed a loss of stall pressure ratio and flow range at design speed and no significant loss in stall pressure ratio at 70 percent of design speed. Detailed flow measurements are presented to show the rotor-upstream flow interactions and the attenuation and amplification properties through the stage.

Sanger, N. L.↗
NASA NTRS1992

Effect of blade planform variation on the forward-flight performance of small-scale rotors

An investigation was conducted in the Glenn L. Martin Wind Tunnel to determine the effect of blade planform variation on the forward-flight performance of four small-scale rotors. The rotors were 5.417 ft in diameter and differed only in blade planform geometry. The four planforms were: (1) rectangular; (2) 3:1 linear taper starting at 94 percent radius; (3) 3:1 linear taper starting at 75 percent radius; and (4) 3:1 linear taper starting at 50 percent radius. Each planform had a thrust-weighted solidity of 0.098. The investigation included forward-flight simulation at advance ratios from 0.14 to 0.43 for a range of rotor lift and drag coefficients. Among the four rotors, the rectangular rotor required the highest torque for the entire range of rotor drag coefficients attained at advanced ratios greater than 0.14 for rotor lift coefficients C sub L from 0.004 to 0.007. Among the rotors with tapered blades and for C sub L = 0.004 to 0.007, either the 75 percent tapered rotor or the 50 percent tapered rotor required the least amount of torque for the full range of rotor drag coefficients attained at each advance ratio. The performance of the 94 percent tapered rotor was generally between that of the rectangular rotor and the 75 and 50 percent tapered rotors at each advance ratio for this range of rotor lift coefficients.

Noonan, Kevin W.↗
NASA NTRS2002

An Engine Research Program Focused on Low Pressure Turbine Aerodynamic Performance

A comprehensive test program was performed in the Propulsion Systems Laboratory at the NASA Glenn Research Center, Cleveland Ohio using a highly instrumented Pratt and Whitney Canada PW 545 turbofan engine. A key objective of this program was the development of a high-altitude database on small, high-bypass ratio engine performance and operability. In particular, the program documents the impact of altitude (Reynolds Number) on the aero-performance of the low-pressure turbine (fan turbine). A second objective was to assess the ability of a state-of-the-art CFD code to predict the effect of Reynolds number on the efficiency of the low-pressure turbine. CFD simulation performed prior and after the engine tests will be presented and discussed. Key findings are the ability of a state-of-the art CFD code to accurately predict the impact of Reynolds Number on the efficiency and flow capacity of the low-pressure turbine. In addition the CFD simulations showed the turbulent intensity exiting the low-pressure turbine to be high (9%). The level is consistent with measurements taken within an engine.

Castner, Raymond↗
NASA NTRS1974

Performance of a 1.15-pressure-ratio axial-flow fan stage with a blade tip solidity of 0.5

The overall and blade-element performance of a low-solidity, low-pressure-ratio, low-tip-speed fan stage is presented over the stable operating range at rotative speeds from 90 to 120 percent of design speed. At design speed a stage peak efficiency of 0.836 was obtained at a weight flow of 30.27 kilograms per second and a pressure ratio of 1.111. The pressure ratio was less than design pressure ratio, and the design energy input into the rotor was not achieved. A mismatch of the rotor and stator blade elements resulted due to the lower than design pressure ratio of the rotor.

Osborn, W. M.↗
NASA NTRS1994

FTAPE: A fault injection tool to measure fault tolerance

The paper introduces FTAPE (Fault Tolerance And Performance Evaluator), a tool that can be used to compare fault-tolerant computers. The tool combines system-wide fault injection with a controllable workload. A workload generator is used to create high stress conditions for the machine. Faults are injected based on this workload activity in order to ensure a high level of fault propagation. The errors/fault ratio and performance degradation are presented as measures of fault tolerance.

Tsai, Timothy K.↗
NASA NTRS1995

FTAPE: A fault injection tool to measure fault tolerance

The paper introduces FTAPE (Fault Tolerance And Performance Evaluator), a tool that can be used to compare fault-tolerant computers. The tool combines system-wide fault injection with a controllable workload. A workload generator is used to create high stress conditions for the machine. Faults are injected based on this workload activity in order to ensure a high level of fault propagation. The errors/fault ratio and performance degradation are presented as measures of fault tolerance.

Tsai, Timothy K.↗
NASA NTRS1987

Communications indices of crew coordination

Verbal exchanges occuring during task execution during full mission two-person simulator flights are used to study the effect of the interactive communication process on crew coordination and performance. The ratio of initiator to response speech is calculated and speech variations are recorded. The results of this study are compared with the findings of Ginnett's (1986) study of leaders. It is shown that low-error crews adopt a standard form of communicating, allowing for the ability to predict one another's behavior, facilitating the coordination process. The higher performance of crews that have flown together before is believed to be due to the increased amount of time for establishing a conventional means of communication.

Kanki, Barbara G.↗
NASA NTRS1996

Aerodynamic Limitations of the UH-60A Rotor

High quality airloads data have been obtained on an instrumented UH-60A in flight and these data provide insight into the aerodynamic limiting behavior of the rotor. At moderate weight coefficients and high advance ratio limiting performance is largely caused by high drag near the blade tip on the advancing side of the rotor as supercritical flow develops on the rotor with moderate to strong, shocks on both surfaces of the blade. Drag divergence data from two-dimensional airfoil tests show good agreement with the development of the supercritical flow regions. Large aerodynamic pitching moments are observed at high advance ratio, as well, and these pitching moments are the source of high torsional moments on the blade and control system loads. These loads occur on the advancing side of the disk and are not related to blade stall which does not occur for these weight coefficients. At high weight coefficients aerodynamic and structural limits are related to dynamic stall cycles that begin on the retreating side of the blade and, for the most severe conditions, carry around to the advancing side of the blade at the presumed first frequency of the blade/control system.

Coleman, Colin P.↗
NASA NTRS1975

Effect of inducer inlet and diffuser throat areas on performance of a low pressure ratio sweptback centrifugal compressor

A low-pressure-ratio centrifugal compressor was tested with nine combinations of three diffuser throat areas and three impeller inducer inlet areas which were 75, 100, and 125 percent of design values. For a given inducer inlet area, increases in diffuser area within the range investigated resulted in increased mass flow and higher peak efficiency. Changes in both diffuser and inducer areas indicated that efficiencies within one point of the maximum efficiency were obtained over a compressor specific speed range of 27 percent. The performance was analyzed of an assumed two-spool open-cycle engine using the 75 percent area inducer with a variable area diffuser.

Klassen, H. A.↗
NASA NTRS1978

Effect of flight loads on turbofan engine performance deterioration

A significant percentage of high bypass ratio, turbofan engine performance deterioration was caused by an increase in operating clearance between fan/compressor and turbine blades and their outer air seals. These increased clearances resulted from rubs induced by a combination of engine power transients and aircraft flight loads. An analytical technique for predicting the effect of quasi-steady state aircraft flight loads on engine performance deterioration was developed and is presented. Thrust, aerodynamic and inertia loads were considered. Analytical results are shown and compared to actual engine test experience.

Stakolich, E. G.↗
NASA NTRS1991

Survey of research on unsteady aerodynamic loading of delta wings

For aeronautical applications, there has been recent interest in accurately determining the aerodynamic forces and moments experienced by low-aspect-ratio wings performing transient maneuvers which go to angles of attack as high as 90 deg. Focusing on the delta planform with sharp leading edges, the paper surveys experimental and theoretical investigations dealing with the associated unsteady flow phenomena. For maximum angles above a value between 30 and 40 deg, flow details and airloads are dominated by hysteresis in the 'bursting' instability of intense vortices which emanate from the leading edge. As examples of relevant test results, force and moment histories are presented for a model series with aspect ratios 1, 1.5 and 2. Influences of key parameters are discussed, notably those which measure unsteadiness. Comparisons are given with two theories: a paneling approximation that cannot capture bursting but clarifies other unsteady influences, and a simplified estimation scheme which uses measured bursting data.

Ashley, H.↗