Results for “power takeoffs” — Page 8

NASA NTRS1992

Overview of NASA HSR high-lift program

The viewgraphs and discussion of the NASA High-Speed Research (HSR) Program being conducted to develop the technologies essential for the successful U.S. development of a commercial supersonic air transport in the 2005 timeframe are provided. The HSR program is being conducted in two phases, with the first phase stressing technology to ensure environmental acceptability and the second phase stressing technology to make the vehicle economically viable (in contrast to the current Concorde design). During Phase 1 of the program, a key element of the environmental emphases is minimization of community noise through effective engine nozzle noise suppression technology and through improving the performance of high-lift systems. An overview of the current Phase 1 High-Lift Program, directed at technology for community noise reduction, is presented. The total target for takeoff engine noise reduction to meet expected regulations is believed to be about 20 EPNdB. The high-lift research is stressing the exploration of innovative high-lift concepts and advanced flight operations procedures to achieve a substantial (approximately 6 EPNdB) reduction in community noise to supplement the reductions expected from engine nozzle noise suppression concepts; primary concern is focused on the takeoff and climbout operations where very high engine power settings are used. Significant reductions in aerodynamic drag in this regime will allow substantial reductions in the required engine thrust levels and therefore reductions in the noise generated.

Gilbert, William P.↗

NASA NTRS2008

Intelligent Engine Systems: Adaptive Control

We have studied the application of the baseline Model Predictive Control (MPC) algorithm to the control of main fuel flow rate (WF36), variable bleed valve (AE24) and variable stator vane (STP25) control of a simulated high-bypass turbofan engine. Using reference trajectories for thrust and turbine inlet temperature (T41) generated by a simulated new engine, we have examined MPC for tracking these two reference outputs while controlling a deteriorated engine. We have examined the results of MPC control for six different transients: two idle-to-takeoff transients at sea level static (SLS) conditions, one takeoff-to-idle transient at SLS, a Bode power command and reverse Bode power command at 20,000 ft/Mach 0.5, and a reverse Bode transient at 35,000 ft/Mach 0.84. For all cases, our primary focus was on the computational effort required by MPC for varying MPC update rates, control horizons, and prediction horizons. We have also considered the effects of these MPC parameters on the performance of the control, with special emphasis on the thrust tracking error, the peak T41, and the sizes of violations of the constraints on the problem, primarily the booster stall margin limit, which for most cases is the lone constraint that is violated with any frequency.

Gibson, Nathan↗

NASA NTRSDate not supplied

Operational Analysis of Vertiport Surface Topology

Urban Air Mobility (UAM) concepts and technologies are being developed to safely enable operations of small, electric-powered or hybrid, pilot-optional, vertical-takeoff-and-landing (VTOL) passenger and cargo aircraft at vertiport facilities in urban and suburban environments. It is likely that many of the highest demand locations for vertiports will be in space constrained urban environments, requiring vertiport designs to maximize throughput within a compact surface footprint. This paper presents several generic vertiport topology design approaches and evaluates their relative surface area utilization and operational efficiency under different wind constrained configurations while meeting safety driven spacing constraints derived from heliport design standards and subject matter expert interviews.

Urban air mobility↗

NASA NTRS1992

Mission and sizing analysis for the Beta II two-stage-to-orbit vehicle

NASA Lewis Research Center studied a horizontal takeoff and landing, fully reusable, two-stage-to-orbit (TSTO) vehicle capable of launching and returning a 10,000 pound payload to low earth orbit using low-risk technology. The vehicle, called Beta 2, was derived from the USAF/Boeing Beta vehicle, a TSTO study vehicle capable of launching a 50,000 pound payload to low earth orbit. Development of the Beta 2 from the USAF/Boeing Beta vehicle occurred in a series of iterations during which the size of the vehicle was decreased to accommodate the smaller payload, the staging Mach number was decreased from 8.0 to 6.5, and the rocket propulsion system was removed from the booster. The final Beta 2 vehicle consisted of a rocket powered orbiter and an all airbreathing booster. The gross takeoff weight of the Beta 2 vehicle was approximately 1.1 million pounds. In addition to its baseline mission, the Beta 2 was capable of delivering approximately 17,500 pounds to the Space Station with the same takeoff gross weight. The mission and sizing analysis performed to arrive at the Beta 2 vehicle is discussed.

Nadell, Shari-Beth↗

NASA NTRS1992

Mission and sizing analysis for the Beta 2 two-stage-to-orbit vehicle

NASA Lewis Research Center studied a horizontal takeoff and landing, fully reusable, two-stage-to-orbit (TSTO) vehicle capable of launching and returning a 10,000 pound payload to low Earth polar orbit using low-risk technology. The vehicle, called Beta 2, was derived from the USAF/Boeing Beta vehicle, a TSTO study vehicle capable of launching a 50,000 pound payload to low Earth polar orbit. Development of the Beta 2 from the USAF/Boeing Beta vehicle occurred in a series of iterations during which the size of the vehicle was decreased to accommodate the smaller payload, the staging Mach number was decreased from 8.0 to 6.5, and the rocket propulsion system was removed from the booster. The final Beta 2 vehicle consisted of a rocket powered orbiter and an all airbreathing booster. The gross takeoff weight of the Beta 2 vehicle was approximately 1.1 million pounds. In addition to its baseline mission, the Beta 2 was capable of delivering approximately 17,500 pounds to the Space Station with the same takeoff gross weight. The mission and sizing analysis performed to arrived at the Beta 2 vehicle is discussed.

Nadell, Shari-Beth↗

NASA NTRS1988

Application of empirical and linear methods to VSTOL powered-lift aerodynamics

Available prediction methods applied to problems of aero/propulsion interactions for short takeoff and vertical landing (STOVL) aircraft are critically reviewed and an assessment of their strengths and weaknesses provided. The first two problems deal with aerodynamic performance effects during hover: (1) out-of-ground effect, and (2) in-ground effect. The first can be evaluated for some multijet cases; however, the second problem is very difficult to evaluate for multijets. The ground-environment effects due to wall jets and fountain flows directly affect hover performance. In a related problem: (3) hot-gas ingestion affects the engine operation. Both of these problems as well as jet noise affect the ability of people to work near the aircraft and the ability of the aircraft to operate near the ground. Additional problems are: (4) the power-augmented lift due to jet-flap effects (both in- and out-of-ground effects), and (5) the direct jet-lift effects during short takeoff and landing (STOL) operations. The final problem: (6) is the aerodynamic/propulsion interactions in transition between hover and wing-borne flight. Areas where modern CFD methods can provide improvements to current computational capabilities are identified.

Margason, Richard↗

NASA NTRS1988

Application of empirical and linear methods to VSTOL powered-lift aerodynamics

Available prediction methods applied to problems of aero/propulsion interactions for short takeoff and vertical landing (STOVL) aircraft are critically reviewed and an assessment of their strengths and weaknesses provided. The first two problems deal with aerodynamic performance effects during hover: (1) out-of-ground effect, and (2) in-ground effect. The first can be evaluated for some multijet cases; however, the second problem is very difficult to evaluate for multijets. The ground-environment effects due to wall jets and fountain flows directly affect hover performance. In a related problem: (3) hot-gas ingestion affects the engine operation. Both of these problems as well as jet noise affect the ability of people to work near the aircraft and the ability of the aircraft to operate near the ground. Additional problems are: (4) the power-augmented lift due to jet-flap effects (both in- and out-of-ground effects), and (5) the direct jet-lift effects during short takeoff and landing (STOL) operations. The final problem: (6) is the aerodynamic/propulsion interactions in transition between hover and wing-borne flight. Areas where modern CFD methods can provide improvements to current computational capabilities are identified.

Margason, Richard↗

NASA NTRSDate not supplied

Tail Sizing Considerations for Wingtip Propulsor Driven Aircraft Applied to the Parallel Electric-Gas Architecture with Synergistic Utilization Scheme (PEGASUS) Concept

This research focuses on the vertical tail sizing implications of a single propulsion system fault when using wingtip propulsors as applied to the PEGASUS concept. PEGASUS is a conceptual regional aircraft featuring wingtip propulsors, an aft boundary layer ingestion propulsor, and inboard propulsors. Using four propulsors on the wing, rather than the typical two, enables a reduction in the vertical tail size needed in the event of a single fault in the propulsion system. Achieving a reduction in vertical tail size, and its associated reduction in drag, is dependent on splitting the takeoff thrust appropriately between the inboard and wingtip propulsors. At takeoff, the wingtip propulsors can only provide a small portion of the takeoff thrust. Compared with a conventional baseline vehicle employing only inboard propulsors, the increased wetted area from the wingtip nacelles outweighs the cruise drag benefits obtained from the reduced tail size and the reduction in wingtip vortices due to the wingtip propellers. The research highlights the need for aggressive cruise drag reductions on PEGASUS, possibly through increased use of the boundary layer ingestion propulsor. By lowering the wingtip propulsor power at cruise, the propulsors would be better sized for takeoff and have smaller nacelles with lower drag.

Nathaniel J Blaesser↗

NASA NTRS1973

Engine-over-the-wing noise research

Acoustic measurements for large model eingine-over-the-wing (EOW) research configurations having both conventional and powered lift applications were taken for flap positions typical of takeoff and approach and at locations simulating flyover and sideline. The results indicate that the noise is shielded by the wing and redirected above it, making the EOW concept a prime contender for quiet aircraft. The large-scale noise data are in agreement with earlier small-model results. Below the wing, the EOW configuration is about 10 PNdb quieter than the engine-under-the-wing externally-blown-flap for powered lift, and up to 10 db quieter than the nozzle alone at high frequencies for conventional lift applications.

Reshotko, M.↗

NASA NTRS1973

Engine-over-the-wing noise research.

Acoustic measurements for large model engine-over-the-wing (EOW) research configurations having both conventional and powered lift applications were taken for flap positions typical of takeoff and approach and at locations simulating flyover and sideline. The results indicate that the noise is shielded by the wing and redirected above it, making the EOW concept a prime contender for quiet aircraft. The large-scale noise data are in agreement with earlier small-model results. Below the wing, the EOW configuration is about 10 PNdB quieter than the engine-under-the-wing externally-blown-flap for powered lift, and up to 10 dB quieter than the nozzle alone at high frequencies for conventional lift applications.

Reshotko, M.↗

NASA NTRS1974

A shuttle development flight test vehicle study

A study is presented that identifies the potential performance capability of the production shuttle orbiter for powered flight tests using several propulsion systems following vertical takeoff and using J-2 rocket engines following air launch. Of the approaches considered, the air-launched orbiter equipped with J-2 rocket engines appeared to have the highest potential for early shuttle development flights. With this approach, mach 4 appeared attainable using 45.5K kg (100K lb) of internal propellant. Several issues were identified that require resolution to prove feasibility.

Rainey, R. W.↗

NASA NTRS1987

The supersonic through-flow turbofan for high Mach propulsion

A study was done to evaluate the potential improvements in aircraft turbine engine performance by incorporating unique supersonic through-flow fans. Engine performance, weight, and mission studies were carried out for conventional turbofan engines using supersonic through-flow fans. A Mach 3 commercial transport mission was considered. The advantages of the supersonic fan engines were evaluated in terms of mission range comparisons between the supersonic fan engines and conventional engines. The installed specific fuel consumption of the supersonic fan engines was 12 percent better than the conventional engines and the installed weight was projected to be 25 percent lighter. For a takeoff gross weight of 550,000 lbs, the aircraft powered by supersonic fan engines had a range capability of 6600 nm compared to 5300 nm (a 25% improvement) for conventional engines.

Franciscus, Leo C.↗

NASA NTRS1987

The supersonic through-flow turbofan for high Mach propulsion

A study was done to evaluate the potential improvements in aircraft turbine engine performance by incorporating unique supersonic through-flow fans. Engine performance, weight, and mission studies were carried out for conventional turbofan engines using supersonic through-flow fans. A Mach 3 commercial transport mission was considered. The advantages of the supersonic fan engines were evaluated in terms of mission range comparisons between the supersonic fan engines and conventional engines. The installed specific fuel consumption of the supersonic fan engines was 12 percent better than the conventional engines and the installed weight was projected to be 25 percent lighter. For a takeoff gross weight of 550,000 lbs, the aircraft powered by supersonic fan engines had a range capability of 6600 nm compared to 5300 nm (a 25 percent improvement) for conventional engines.

Franciscus, Leo C.↗

NASA NTRS1992

Internal reversing flow in a tailpipe offtake configuration for SSTOVL aircraft

A generic one-third scale model of a tailpipe offtake system for a supersonic short takeoff vertical landing (SSTOVL) aircraft was tested at LeRC Powered Lift Facility. The model consisted of a tailpipe with twin elbows, offtake ducts, and flow control nozzles, plus a small ventral nozzle and a blind flange to simulate a blocked cruise nozzle. The offtake flow turned through a total angle of 177 degrees relative to the tailpipe inlet axis. The flow split was 45 percent to each offtake and 10 percent to the ventral nozzle. The main test objective was to collect data for comparison to the performance of the same configuration predicted by a computational fluid dynamics (CFD) analysis. Only the experimental results are given - the analytical results are published in a separate paper. Performance tests were made with unheated air at tailpipe-to-ambient pressure ratios up to 5. The total pressure loss through the offtakes was as high as 15.5 percent. All test results are shown as graphs, contour plots, and wall pressure distributions. The complex flow patterns in the tailpipe and elbows at the offtake openings are described with traversing flow angle probe and paint streak flow visualization data.

Mcardle, Jack G.↗

NASA NTRS1992

Internal reversing flow in a tailpipe offtake configuration for SSTOVL aircraft

A generic one-third scale model of a tailpipe offtake system for a supersonic short takeoff vertical landing (SSTOVL) aircraft was tested at LeRC Powered Lift Facility. The model consisted of a tailpipe with twin elbows, offtake ducts, and flow control nozzles, plus a small ventral nozzle and a blind flange to simulate a blocked cruise nozzle. The offtake flow turned through a total angle of 177 degrees relative to the tailpipe inlet axis. The flow split was 45 percent to each offtake and 10 percent to the ventral nozzle. The main test objective was to collect data for comparison to the performance of the same configuration predicted by a computational fluid dynamics (CFD) analysis. Only the experimental results are given - the analytical results are published in a separate paper. Performance tests were made with unheated air at tailpipe-to-ambient pressure ratios up to 5. The total pressure loss through the offtakes was as high as 15.5 percent. All test results are shown as graphs, contour plots, and wall pressure distributions. The complex flow patterns in the tailpipe and elbows at the offtake openings are described with traversing flow angle probe and paint streak flow visualization data.

Mcardle, Jack G.↗

NASA NTRS1993

A Large Hemi-Anechoic Enclosure for Community-Compatible Aeroacoustic Testing of Aircraft Propulsion Systems

A large hemi-anechoic (absorptive walls and acoustically hard floor) noise control enclosure has been erected around a complex of test stands at the NASA Lewis Research Center in Cleveland, Ohio. This new state-of-the-art Aeroacoustic Propulsion Laboratory (APL) provides an all-weather, semisecure test environment while limiting noise to acceptable levels in surrounding residential neighborhoods. The 39.6 m (130 ft) diameter geodesic dome structure houses the new Nozzle Aeroacoustic Test Rig (NATR), an ejector-powered M = 0.3 free jet facility for acoustic testing of supersonic aircraft exhaust nozzles and turbomachinery. A multi-axis, force-measuring Powered Lift Facility (PLF) stand for testing of Short Takeoff Vertical Landing (STOVL) vehicles is also located within the dome. The design of the Aeroacoustic Propulsion Laboratory efficiently accomodates the research functions of two separate test rigs, one of which (NATR) requires a specialized environment for taking acoustic measurements. Absorptive fiberglass wedge treatment on the interior surface of the dome provides a hemi-anechoic interior environment for obtaining the accurate acoustic measurements required to meet research program goals. The APL is the first known geodesic dome structure to incorporate transmission-loss properties as well as interior absorption into a free-standing, community-compatible, hemi-anechoic test facility.

Cooper, Beth A.↗

NASA NTRSDate not supplied

Considering Turbofan Operability in Hybrid Electric Aircraft Propulsion System Design

This paper explores the design of a hybrid electric aircraft propulsion system that uses a turbofan to power an electric system. In such a system, the gas turbine will experience a loss of power generation as altitude increases, however the electric system will not. This difference results in designs that may over size the electric system at high altitude or under size at low altitude. Two studies are performed within this paper. The first looks at extracting power from the engine for use with electric aircraft propulsion at cruise and the second reviews a design of an engine that uses thrust assist for takeoff. Both studies look at the effects of changing altitude on the amount of power extraction or insertion that can be taken from the turbofan as dictated by operability limits. Results of the paper show that low-pressure compressor surge margin and high-pressure compressor speed can be pushed to unaccepted limits with large scale power extraction or insertion, however these issues can be mitigated by adding power extraction or insertion at off design operating points to compensate. Additionally, the benefits of thrust assist are quantified for this configuration demonstrating a reduction in thrust specific fuel consumption at cruise of over 5%.

Gas Turbine↗

NASA NTRS2023

Considering Turbofan Operability in Hybrid Electric Aircraft Propulsion System Design

This paper explores the design of a hybrid electric aircraft propulsion system that uses a turbofan to power an electric system. In such a system, the gas turbine will experience a loss of power generation as altitude increases, however the electric system will not. This difference results in designs that may over size the electric system at high altitude or under size at low altitude. Two studies are performed within this paper. The first looks at extracting power from the engine for use with electric aircraft propulsion at cruise and the second reviews a design of an engine that uses thrust assist for takeoff. Both studies look at the effects of changing altitude on the amount of power extraction or insertion that can be taken from the turbofan as dictated by operability limits. Results of the paper show that low-pressure compressor surge margin and high-pressure compressor speed can be pushed to unaccepted limits with large scale power extraction or insertion, however these issues can be mitigated by adding power extraction or insertion at off design operating points to compensate. Additionally, the benefits of thrust assist are quantified for this configuration demonstrating a reduction in thrust specific fuel consumption at cruise of over 5%.

Gas turbine↗