Search NASA⌕ Search

SEARCH · Search NASA

Results for “prediction correction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

Turbulence Model Predictions of Strongly Curved Flow in a U-Duct

The ability of three types of turbulence models to accurately predict the effects of curvature on the flow in a U-duct is studied. An explicit algebraic stress model performs slightly better than one- or two-equation linear eddy viscosity models, although it is necessary to fully account for the variation of the production-to-dissipation-rate ratio in the algebraic stress model formulation. In their original formulations, none of these turbulence models fully captures the suppressed turbulence near the convex wall, whereas a full Reynolds stress model does. Some of the underlying assumptions used in the development of algebraic stress models are investigated and compared with the computed flowfield from the full Reynolds stress model. Through this analysis, the assumption of Reynolds stress anisotropy equilibrium used in the algebraic stress model formulation is found to be incorrect in regions of strong curvature. By the accounting for the local variation of the principal axes of the strain rate tensor, the explicit algebraic stress model correctly predicts the suppressed turbulence in the outer part of the boundary layer near the convex wall.

Rumsey, Christopher L.↗
NASA NTRS1995

Experimental and Computational Analysis of Shuttle Orbiter Hypersonic Trim Anomaly

During the high-Mach-number, high-altitude portion of the first entry of the Shuttle Orbiter, the vehicle exhibited a nose-up pitching moment relative to preflight prediction of approximately Delta Cm = 0.03. This trim anomaly has been postulated to be due to compressibility, viscous, and/or real-gas (lowered specific heat ratio gamma) effects on basic body pitching moment, body-flap effectiveness, or both. In order to assess the relative contribution of each of these effects, an experimental study was undertaken to examine the effects of Mach number, Reynolds number, and ratio of specific heats. Complementary computational solutions were obtained for wind-tunnel and flight conditions. The primary cause of the anomaly was determined to be lower pressures on the aft windward surface of the Orbiter than deduced from hypersonic wind-tunnel tests with ideal- or near-ideal-gas test flow. The lower pressure levels are a result of the lowering of the flowfield gamma due to high-temperature effects. This phenomenon was accurately simulated in a hypersonic wind tunnel using a heavy gas, which provided a lower, gamma, and was correctly predicted by Navier-Stokes computations using nonequilibrium chemistry.

Brauckmann, Gregory J.↗
NASA NTRS2017

Validation of Test Methods for Air Leak Rate Verification of Spaceflight Hardware

As deep space exploration continues to be the goal of NASAs human spaceflight program, verification of the performance of spaceflight hardware becomes increasingly critical. Suitable test methods for verifying the leak rate of sealing systems are identified in program qualification testing requirements. One acceptable method for verifying the air leak rate of gas pressure seals is the tracer gas leak detector method. In this method, a tracer gas (commonly helium) leaks past the test seal and is transported to the leak detector where the leak rate is quantified. To predict the air leak rate, a conversion factor of helium-to-air is applied depending on the magnitude of the helium flow rate. The conversion factor is based on either the molecular mass ratio or the ratio of the dynamic viscosities. The current work was aimed at validating this approach for permeation-level leak rates using a series of tests with a silicone elastomer O-ring. An established pressure decay method with constant differential pressure was used to evaluate both the air and helium leak rates of the O-ring under similar temperature and pressure conditions. The results from the pressure decay tests showed, for the elastomer O-ring, that neither the molecular flow nor the viscous flow helium-to-air conversion factors were applicable. Leak rate tests were also performed using nitrogen and argon as the test gas. Molecular mass and viscosity based helium-to-test gas conversion factors were applied, but did not correctly predict the measured leak rates of either gas. To further this study, the effect of pressure boundary conditions was investigated. Often, pressure decay leak rate tests are performed at a differential pressure of 101.3 kPa with atmospheric pressure on the downstream side of the test seal. In space applications, the differential pressure is similar, but with vacuum as the downstream pressure. The same O-ring was tested at four unique differential pressures ranging from 34.5 to 137.9 kPa. Up to six combinations of upstream and downstream pressures for each differential pressure were compared. For a given differential pressure, the various combinations of upstream and downstream dry air pressures did not significantly affect the leak rate. As expected, the leak rate of the O-ring increased with increasing differential pressure. The results suggested that the current leak test pressure conditions, used to verify spacecraft sealing systems with elastomer seals, produce accurate values even though the boundary conditions do not model the space application.

helium leak detector↗
NASA NTRS2006

Computational Analysis of a Chevron Nozzle Uniquely Tailored for Propulsion Airframe Aeroacoustics

A computational flow field and predicted jet noise source analysis is presented for asymmetrical fan chevrons on a modern separate flow nozzle at take off conditions. The propulsion airframe aeroacoustic asymmetric fan nozzle is designed with an azimuthally varying chevron pattern with longer chevrons close to the pylon. A baseline round nozzle without chevrons and a reference nozzle with azimuthally uniform chevrons are also studied. The intent of the asymmetric fan chevron nozzle was to improve the noise reduction potential by creating a favorable propulsion airframe aeroacoustic interaction effect between the pylon and chevron nozzle. This favorable interaction and improved noise reduction was observed in model scale tests and flight test data and has been reported in other studies. The goal of this study was to identify the fundamental flow and noise source mechanisms. The flow simulation uses the asymptotically steady, compressible Reynolds averaged Navier-Stokes equations on a structured grid. Flow computations are performed using the parallel, multi-block, structured grid code PAB3D. Local noise sources were mapped and integrated computationally using the Jet3D code based upon the Lighthill Acoustic Analogy with anisotropic Reynolds stress modeling. In this study, trends of noise reduction were correctly predicted. Jet3D was also utilized to produce noise source maps that were then correlated to local flow features. The flow studies show that asymmetry of the longer fan chevrons near the pylon work to reduce the strength of the secondary flow induced by the pylon itself, such that the asymmetric merging of the fan and core shear layers is significantly delayed. The effect is to reduce the peak turbulence kinetic energy and shift it downstream, reducing overall noise production. This combined flow and noise prediction approach has yielded considerable understanding of the physics of a fan chevron nozzle designed to include propulsion airframe aeroacoustic interaction effects.

Massey, Steven J.↗
NASA NTRS2023

Numerical Investigation of C L,max Prediction on the NASA High-Lift Common Research Model

An assessment of a Hybrid RANS/LES (HRLES) approach for C L,max prediction is presented for the NASA High-Lift Common Research Model (CRM-HL). Both free air and wind tunnel configurations of the CRM-HL are investigated and the results are compared to the QinetiQ wind tunnel experiments and two other numerical approaches: Reynolds Averaged Navier-Stokes (RANS) and Wall-Modeled Large Eddy Simulations (WMLES). For the free-air configuration, HRLES is shown to address some of the known shortcomings with RANS and prevent inboard and outboard flow separation particularly in the region of C L,max and post-stall. To achieve these improvements over RANS, LES-appropriate grids and numerical discretizations are required. It was also found that when applying HRLES to a RANS best practice grid and numerics that the HRLES method significantly underperformed RANS. For the in-tunnel configuration, HRLES showed good agreement with the loads, surface pressure and oil-flow photographs obtained in the experiment. HRLES was able to improve upon the RANS simulations, which showed a sharp loss of lift at the two highest angles-of-attack due to large scale inboard and outboard separation on the wing, by correctly predicting the corner flow separation and showing remarkably close agreement in the flow topologies with the experiment.

TTT↗
NASA NTRS2009

Forecasting Lightning Threat using Cloud-resolving Model Simulations

As numerical forecasts capable of resolving individual convective clouds become more common, it is of interest to see if quantitative forecasts of lightning flash rate density are possible, based on fields computed by the numerical model. Previous observational research has shown robust relationships between observed lightning flash rates and inferred updraft and large precipitation ice fields in the mixed phase regions of storms, and that these relationships might allow simulated fields to serve as proxies for lightning flash rate density. It is shown in this paper that two simple proxy fields do indeed provide reasonable and cost-effective bases for creating time-evolving maps of predicted lightning flash rate density, judging from a series of diverse simulation case study events in North Alabama for which Lightning Mapping Array data provide ground truth. One method is based on the product of upward velocity and the mixing ratio of precipitating ice hydrometeors, modeled as graupel only, in the mixed phase region of storms at the -15\dgc\ level, while the second method is based on the vertically integrated amounts of ice hydrometeors in each model grid column. Each method can be calibrated by comparing domainwide statistics of the peak values of simulated flash rate proxy fields against domainwide peak total lightning flash rate density data from observations. Tests show that the first method is able to capture much of the temporal variability of the lightning threat, while the second method does a better job of depicting the areal coverage of the threat. A blended solution is designed to retain most of the temporal sensitivity of the first method, while adding the improved spatial coverage of the second. Weather Research and Forecast Model simulations of selected North Alabama cases show that this model can distinguish the general character and intensity of most convective events, and that the proposed methods show promise as a means of generating quantitatively realistic fields of lightning threat. However, because models tend to have more difficulty in correctly predicting the instantaneous placement of storms, forecasts of the detailed location of the lightning threat based on single simulations can be in error. Although these model shortcomings presently limit the precision of lightning threat forecasts from individual runs of current generation models, the techniques proposed herein should continue to be applicable as newer and more accurate physically-based model versions, physical parameterizations, initialization techniques and ensembles of cloud-allowing forecasts become available.

McCaul, E. W., Jr.↗
DOE OSTI2025

Effects of Atmosphere and Ocean Horizontal Model Resolution on Tropical Cyclone and Upper-Ocean Response Forecasts in Four Major Hurricanes

A coupled atmosphere–ocean model is necessary for tropical cyclone (TC) prediction to accurately characterize ocean feedback on atmospheric processes within the TC environment. Here, the ECMWF coupled global model is run at horizontal resolutions from 9 to 1.4 km in the atmosphere, as well as 25 and 8 km in the ocean, to identify how resolution impacts forecast accuracy of four observed major TCs in the Atlantic: Irma, Florence, Teddy, and Ida. Most of the resolutions used here are unprecedented for global models. GOES-16 and synthetic aperture radar (SAR) satellite images and best track data are used for atmospheric validation. Salinity and temperature observations from Air-Launched Autonomous Micro-Observer (ALAMO) floats are used to validate modeled upper-ocean response, including mixed layer deepening, sea surface cooling, and near-inertial waves in the wakes of TCs. Increasing atmospheric resolution leads to more realistic TC structure and stronger winds, significantly improving TC intensity forecasts and modestly improving track errors. Ocean resolution impacts the upper-ocean response but does not influence atmospheric forecasts for the fast-moving TCs considered here. Stronger mixing, sea surface cooling, and near-inertial oscillations are found for both higher atmosphere and ocean resolutions, provided the initial upper-ocean state is the same for the two ocean resolutions. Whether this agrees better with the ALAMO observations also depends on the realism of the initial upper-ocean state in the model, emphasizing the importance of ocean initialization for the accurate upper-ocean response. Overall, the model at all resolutions correctly predicts stronger mixing, surface cooling, and near-inertial oscillation amplitudes to the right of a TC center, as observed by ALAMO floats.

Atmosphere-ocean interaction↗
NASA NTRSDate not supplied

Decision Aid for Conjunction Risk Mitigation by Differential Drag

In the previous five years, the rate of conjunctions that the NASA Conjunction Assessment Risk Analysis (CARA) team processed and analyzed has more than tripled. (NASA CARA, 2024) New missions in the early development phases are now required to plan for dealing with conjunctions under the present space environment, and also projecting forward into a future likely with even further increased utilization of the space environment. Some missions are investigating the possibility of using differential drag to remediate conjunctions without expending limited fuel or for missions without propulsive capabilities. The NASA CARA team studied the historical record of conjunctions to evaluate the circumstances under which differential drag may be successfully applied and have developed a series of tables to use as a decision aid for missions considering differential drag. Currently, if a CARA-protected mission with maneuvering capabilities is predicted to have a conjunction with probability of collision (Pc) greater than 7E-5 (the default value of the ‘yellow threshold’, which may have some other value agreed by CARA and the mission during the Orbital Collison Avoidance Planning (OCAP) process), CARA will use its Maneuver Trade Space (MTS) tool to evaluate and recommend options for the timing and magnitude of a risk mitigation maneuver (RMM), based on the mission’s capabilities. If the conjunction’s Pc is greater than 1E-4, the ‘red threshold’, then an RMM must be executed per NASA Procedural Requirements (NPR) 8079.1 (NASA, 2023), although missions may execute an RMM even if the Pc is lower. The magnitude of the maneuver is typically a few cm/s, and CARA estimates how many will be required for the mission’s nominal lifetime – typically a few per year – during the OCAP process, to inform the mission’s delta-V requirement. For traditional satellites, this is usually smaller than other requirements for orbit insertion, maintenance, and disposal, but for CubeSats or other small satellite missions, a propulsion system may not provide much more than a few cm/s of delta-V or may not fit at all within the available budget of money, time, size, weight, and/or power (SWaP). Conversely, CubeSats often have deployable solar panels, which offer the capacity to have much higher areas facing some directions than others. Such a mission can instead use ‘differential drag’ to remediate a conjunction -- in other words, change its drag area (usually increasing) to deviate from the predicted collision course. This is how Planet’s Dove spacecraft maintain their formations and remediate conjunction risks without having on-board propulsion (Foster, et al., 2017) (Griffith, et al., 2021). CARA has been developing improvements to MTS to support differential-drag for NASA's missions -- where it is effective. CARA records all conjunctions of their protected payloads, with historical records starting in 2005 (with significant conjunction events starting to occur on or after 2013). From this record, approximately 7,300 had a Pc greater than 1E-4 at 3 days prior to the time of closest approach, the time analyzed for differential drag efficacy. Of those, approximately 4,300 had fully-defined covariance matrices stored for both the primary and secondary objects; this set of conjunctions is the basis for the analysis of this work. CARA’s MTS tool was used to propagate the primary satellite forward from that decision point with varying degrees of increase to ballistic coefficient (BC). Because these conjunctions came from multiple missions, the nondimensional ‘delta-BC’ factor was used to quantify and normalize the increase in ballistic coefficient, defined as follows: Delta-BC = BC_new / BC_old - 1 Positive delta-BC factors represent an increase in drag compared to the nominal attitude, while negative delta-BC factors (to a minimum of -1) represent a decrease in drag. At the conclusion of the differential-drag ‘maneuver’, the Pc was recalculated to evaluate whether or not the conjunction was mitigated (Pc < 3E-6). These results were then binned and sorted along several axes, including altitude, amount of delta-BC, and (pre-maneuver) rate of energy dissipation (EDR), to identify underlying patterns. The altitude plot is shown in Figure 1. To validate this analysis, we consulted the record of a NASA mission which uses differential drag to maintain its orbit and remediate conjunction risk. CARA’s empirical record of the mission’s orbit history suggests it achieves a delta-BC of 2.2. Of the twenty-one RMM plans that were submitted by this mission, eighteen were matched with conjunctions in the historical record; of those, twelve were successfully remediated (final measured Pc < 3E-6), and six were not. This is consistent with the expected efficacy for missions orbiting at that altitude. We are presently simulating this mission’s RMMs with MTS; this work is ongoing, but so far, the MTS results are qualitatively in agreement with the empirical results -- correctly predicting that a maneuver would or would not remediate a conjunction, if not exactly matching the final post-remediation Pc value. We found that differential drag was most successful for satellites with perigees below 560 km, and which could adopt an average delta-BC of 2 or greater (that is, increasing their ballistic coefficient by a factor of 3). However, this is a difficult threshold for a mission to clear; very few spacecraft are capable of adopting a high-drag configuration for 72 hours continuously. Planet’s Dove spacecraft use differential drag to remediate conjunctions (Griffith, et al., 2021), and they have a maximum delta-BC factor of 9, but in practice (with mission and charging constraints) they achieve a time-averaged delta-BC that is closer to 2 (Foster, et al., 2017). A mission’s differential drag utility strongly depends on the operational constraints that has the capacity to limit the time-averaged delta-BC. A mission with a high maximum delta-BC of 5 or more can have an effective delta-BC of less than 1 due to operational constraints such as instrument and solar panel pointing, especially if this constraint results in holding an intermediate drag value for most of its orbit. CARA has developed tables that can be used as decision aids to advise missions-in-development about the best way to utilize their differential drag capabilities. For missions below 560 km with the operational flexibility to devote multiple days to holding a high-drag configuration (or a sufficiently high drag ratio to compensate for limitations on that time), they are -- more likely than not -- able to successfully remediate high-risk conjunctions. Conversely, missions that do not meet these exacting criteria -- most missions -- can instead be advised to use on-board propulsion systems to perform RMMs, or to turn their minimum-area face towards the approach vector, thereby reducing Pc at the moment of conjunction due to the decreased Hard-Body Radius (HBR), that is a strongly correlated variable in the Pc calculations. (NASA, 2023)

conjunction assessment↗
DOE OSTI2024

A coarse-grained model of clay colloidal aggregation and consolidation with explicit representation of the electrical double layer

The aggregation of clay minerals in liquid water exemplifies colloidal self-assembly in nature. These negatively charged aluminosilicate platelets interact through multiple mechanisms with different sensitivities to particle shape, surface charge, aqueous chemistry, and interparticle distance and exhibit complex aggregation structures. Experiments have difficulty resolving the associated colloidal assemblages at the scale of individual particles. Conversely, all-atom molecular dynamics (MD) simulations provide detailed insight on clay colloidal interaction mechanisms, but they are limited to systems containing a few particles. We develop a new coarse-grained (CG) model capable of representing assemblages of hundreds of clay particles with accuracy approaching that of MD simulations, at a fraction of the computational cost. Our CG model is parameterized based on MD simulations of a pair of smectite clay particles in liquid water. A distinctive feature of our model is that it explicitly represents the electrical double layer (EDL), i.e., the cloud of charge-compensating cations that surrounds the clay particles. Our model captures the simultaneous importance of long-range colloidal interactions (i.e., interactions consistent with simplified analytical models, already included in extant clay CG models) and short-range interactions such as ion correlation and surface and ion hydration effects. The resulting simulations correctly predict, at low solid-water ratios, the existence of ordered arrangements of parallel particles separated by water films with a thickness up to ~10 nm and, at high solid-water ratios, the coexistence of crystalline and osmotic swelling states, in agreement with experimental observations.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

William A. Bardeen: A life in physics and the legacy of the chiral anomaly

William Allan Bardeen (September 15, 1941 − November 18, 2025) was an American theoretical physicist who worked at the Fermi National Accelerator Laboratory. He is renowned for his foundational work on the chiral anomaly, the Adler-Bardeen theorem, the non-Abelian anomaly and gravitational anomalies. He was instrumental in the development of quantum chromodynamics and its applications, such as semileptonic decays and the Λ $\overline{MS}$ scheme frequently used in perturbative analysis of high energy processes involving strong interactions. Bardeen also played a major role in developing a theory of dynamical breaking of electroweak symmetry via top quark condensates, leading to one of the first composite Brout-Englert-Higgs boson models. His work on the chiral symmetry dynamics of heavy-light quark bound states correctly predicted abnormally long-lived resonances which are chiral symmetry partners of the ground state.

Hill, Christopher T. [Fermi National Accelerator L↗
DOE OSTI2025

Modeling High Current Pulsed Discharge in AA Battery Cathodes: The Effect of Localized Charging during Rest

During high current operation, substantial heterogeneity develops within battery cathodes, particularly when their thickness is large. Heterogeneity relaxation during subsequent rest is important for understanding battery performance under pulsed conditions. Localized charge balancing phenomena within batteries at zero net current are not well understood and merit investigation. In this work, the heterogeneity within cathodes of commercial alkaline Zn–MnO 2 batteries is measured during discharge and monitored during rest using energy dispersive X-ray diffraction (EDXRD). Significant gradients in protonation form during discharge and partially relax under rest. It is demonstrated that the proton gradient relaxation is through local redox activity at zero net current, where local (de)protonation works to redistribute charge across the cathode thickness. To support this redox-based relaxation, a fundamental kinetic study on prismatic MnO 2 cathodes is conducted to determine an appropriate model to describe both discharge and charge kinetics of MnO 2 . These kinetics are incorporated into a computational model to simulate the proton gradient formation and partial relaxation under identical discharge conditions as the operando EDXRD experiments. Model and experimental data are found to be in excellent agreement, correctly predicting localized charge balancing at rest.

Batteries↗
DOE OSTI2025

Libration of hydroxyl groups in layered aluminum (oxy)hydroxides and other material analogs: insights from inelastic neutron scattering and theory

We analyzed the hydroxyl librational signatures of five structurally related aluminum (oxy)hydroxides, using inelastic neutron scattering (INS) and plane-wave lattice dynamics simulations. A clear trend across these aluminum-containing phases illustrates the relationship between hydrogen bonding, local atomic structure, and the spectral location and profile of the librational bands. The INS spectra have been compared to previous optical spectroscopy and computational studies, highlighting the complementary nature of the INS technique. Taking into account other structurally or chemically related material analogs, we have identified a correlation between a blueshift (to higher energy) of the upper librational band edge and the geometry of the hydrogen bond interactions, mirroring (with opposite correlation) the well-known redshift in the intramolecular O–H stretching energy with increasing hydrogen bond strength. For hydroxyl groups that do not participate in hydrogen bonding effectively, the bending librations occur at lower energies and hybridize with metal–oxygen lattice modes. Standard density functional theory approximations, including dispersion corrections, struggle to correctly predict vibrational frequencies of motions dominated by H but perform well for metal–oxygen modes, allowing us to make detailed mode assignments in several cases, including a demonstration of how layer-to-layer disorder in boehmite hydrogen bond orientations is reflected in the sharp but minor low energy peaks (at ∼70–80 meV) of the INS spectrum.

Wang, Hsiu-Wen [Oak Ridge National Laboratory (ORN↗
DOE OSTI2024

Synthesis and investigation into explosive sensitivity for a series of new picramide explosives

Tailoring the molecular properties that govern energetic material sensitivity is essential to improve safety and help develop new energetic materials. Despite this need, understanding the complex chemistry and physics of explosive initiation and propagation is still a challenge. Recent work by our group has reinforced the view that explosive sensitivity under sub-shock conditions is connected to the strength of the weakest covalent bond in the molecule, that is, its “trigger linkage.” These correlations have been observed with different classes of energetic molecules and indicate that “trigger linkage” bond breaking, and heat of explosion are good indicators for the sensitivity trends. Herein we report the synthesis of aliphatic energetic materials with ethane, propane and neopentane backbones. Experimental and computational studies show that the trigger linkage model, based on results from quantum molecular dynamics simulations, correctly predicts trends observed in the impact sensitivity of the molecules. However, while the model predicts the impact sensitivities of the ethane series, the neopentane series has higher impact sensitivities than predicted, which is presumably influenced by crystal packing effects.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Plasma confinement state classification via FPP relevant microwave diagnostics

We present a parsimonious and robust machine learning approach for identifying plasma confinement states in fusion power plants (FPPs) where reliable identification of the low-confinement and high-confinement regimes is critical for safe and efficient operation. Unlike research-oriented devices, FPPs must operate with a severely constrained set of diagnostics. To address this challenge, we demonstrate that a minimalist model, using only electron cyclotron emission (ECE) signals, can achieve accurate and reliable state classification. ECE provides electron temperature profiles without the engineering or survivability issues of in-vessel probes, making it a primary candidate for FPP-relevant diagnostics. Our framework employs ECE as input, extracts features using radial basis functions, and applies a gradient boosting classifier, achieving a test accuracy of 96% (correct predictions). Robustness analysis and feature importance analyzes confirm the approach’s reliability. These results demonstrate that state-of-the-art performance is attainable from a restricted diagnostic set, paving the way for minimalist yet resilient plasma control architectures for FPPs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Nonlinear gyrokinetic modelling of high confinement negative triangularity plasmas

Abstract Nonlinear gyrokinetic simulations correctly predict particle as well as ion and electron energy fluxes of high confinement plasmas with a negative triangularity cross sectional shape, showing that core transport in these plasmas is well described by standard gyrokinetic models. Experimentally inferred power balance fluxes are mostly reproduced within one standard deviation across a wide portion of the minor radius. Experimental conditions are reproduced by ion scale simulations, without the need to include density and temperature profile curvature effects. The experimental case is used as baseline to predict that the non-dimensional confinement scaling in negative triangularity plasmas increases strongly with plasma current while slightly degrading at increasing normalized pressure and decreasing collisionality. Recent experiments showed that low toroidal rotation negatively impacts confinement; consistent with the experiment, simulations predict that low rotational shear significantly affects confinement unless the plasma effective charge is maintained above a minimum level. Core confinement is predicted to significantly degrade in low aspect ratio devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Compressing Hamiltonians with ab initio downfolding for simulating strongly-correlated materials on quantum computers

The accurate first-principles description of strongly correlated materials is an important and challenging problem in condensed matter physics. Ab initio downfolding has emerged as a way of deriving compressed many-body Hamiltonians that maintain the essential physics of strongly correlated materials. The solution of these material-specific models is still exponentially difficult to generate on classical computers, but quantum algorithms allow for a significant speed-up in obtaining the ground states of these compressed Hamiltonians. Here, we demonstrate that using quantum algorithms to obtain the properties of downfolded Hamiltonians can indeed yield high-fidelity solutions. By combining ab initio downfolding and variational quantum eigensolvers, we correctly predict the antiferromagnetic state of one-dimensional cuprate Ca 2 Cu O 3 , the excitonic ground state of monolayer W Te 2 , and the charge-ordered state of correlated metal Sr VO 3 . Numerical simulations using a classical tensor network implementation of variational quantum eigensolvers allow us to simulate large models with up to 54 qubits and encompassing up to four bands in the correlated subspace, which is indicative of the complexity that our framework can address. Through these methods we demonstrate the potential of classical preoptimization and downfolding techniques for enabling efficient materials simulation using quantum algorithms.

Alvertis, Antonios M. [NASA, Ames; LBNL, Berkeley]↗
DOE OSTI2025

Energy dependence of polarized 𝛾⁢𝛾 → 𝑒 + ⁢ 𝑒− in peripheral Au+Au collisions at $\sqrt{s_{NN}}$ = 54.4 and 200 GeV with the STAR experiment at RHIC

We report the differential yields at mid-rapidity of the Breit-Wheeler process (𝛾⁢𝛾 → 𝑒 + ⁢𝑒 − ) in peripheral Au+Aucollisions at $\sqrt{s_{NN}}$ = 54.4 and 200 GeV with the STAR experiment at the Relativistic Heavy Ion Collider (RHIC), as a function of energy $\sqrt{s_{NN}}$, 𝑒 + ⁢𝑒 − transverse momentum 𝑝 T , 𝑝$^{2}_{T}$, invariant mass 𝑀 𝑒⁢𝑒 , and azimuthal angle. In the invariant mass range of 0.4 < 𝑀 𝑒⁢𝑒 < 2.6GeV/𝑐 2 at low transverse momentum (𝑝 T < 0.15GeV/𝑐), the yields increase while the pair √⟨𝑝$^{2}_{T}$⟩ decreases with increasing $\sqrt{s_{NN}}$, a feature that is correctly predicted by the QED calculation. Here, the energy dependencies of the measured quantities are sensitive to the nuclear form factor, infrared divergence and photon polarization. The data are compiled and used to extract the charge radius of the Au nucleus.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2025

Macro-micro multiscale modeling to assist the design of HPDC Al castings microstructure and alloys for EV super-large body structures (Phase 1)

Implementation of High Pressure Die Casting (HPDC) Aluminum (Al) body structures for high volume electrified vehicles (EV) to improve electric efficiency remains a key strategy within many original equipment manufacturer (OEM)s. In addition to high strength for safety requirements, superior Self-Piercing Riveting (SPR) performance is demanded for HPDC Al alloys to be compatible with high volume SPR joining. In this work, it is proposed to extend and validate an existing Contractor finite element multiscale macro-micro modeling approach to quantify the influence of the microstructure of HPDC alloys on the fracture strain/displacement under 3-point bend and clinch testing. The success of this work will allow to replace solution treatment stage with low energy consumption heat treatment (HT) processes, or to design new non heat treatable (NHT) HPDC Al alloys to eliminate HT requirements. Ultimately, this project will facilitate the application of HPDC Al alloys for super-large vehicle structures to significantly reduce vehicle weight, and thus improving energy efficiency. The purpose of this project is to extend and validate an existing finite element code, which is based on the Contractor developed macro-micro multi-scale modeling approach, to numerically simulate the three-point bending and clinch test and study the influences of material microstructural characteristics and phase properties on the rivetability. The macro-micro modeling approach begins with a sample scale model and identify the location, which is mostly prone to failure, the deformation history of the boundaries of that location calculated will be used to drive a microstructure-based sub-models where the material microstructure and microscale properties are considered. Using this approach, the wrap-bending failure for two Al alloys are correctly predicted for the first time. This will start with phase I effort of building a framework of macro-micro three point bending test and clinch test of Al10SiMgMn HPDC alloy in the as-cast and T7 heat treated conditions. Those results will then be validated with experimental test results. The phase II effort will involve the utilization of the knowledge learned in phase I to establish the quantitative correlation between the microstructure characteristics and the riveting performance, which will be further used to guide the optimization of HPDC Al alloy microstructure using heat treatment process to achieve sufficient rivetability to join large thin-wall HPDC alloys.

36 MATERIALS SCIENCE↗