Search NASA⌕ Search

SEARCH · Search NASA

Results for “process intensification”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Advanced CO 2 Capture Solvent Systems for Dynamic Power Generation

RTI International, in collaboration with Pacific Northwest National Laboratory (PNNL), Carbon Capture Simulation for Industry Impact (CCSI 2 ), Electricity Power Research Institute (EPRI), and West Virginia University (WVU), successfully completed a joint research effort in developing a cost-effective, resilient, load-following advanced CO 2 capture technology for natural gas power plants. The project’s objective was to develop a CO 2 capture process that maximizes the net present value (NPV) of the electricity sale by minimizing the levelized cost of electricity (LCOE) under dynamic plant loads and high renewable penetration environments. The two key innovations developed in this project were the use of (i) advanced water-lean solvents (WLSs) and (ii) process intensification equipment, such as a rotating packed bed (RPB) absorber and dual-stage flash regeneration. The process’s low CO 2 capture cost is realized through WLSs’ low energy required for solvent regeneration, which lowers the operating cost while RPBs intensify the absorption process and reduces the power plant capital cost. A suite of advanced computational and simulation packages was implemented to guide the process design, validate the dynamic response of the capture plant, evaluate system-wide performance, and maximize the power plant’s profit. The project also engaged with power producers and other stakeholders to ensure its technical relevance and techno-economic viability. The development of this highly disruptive CO 2 capture technology could accelerate the industry adoption and thereby lower the greenhouse gas emissions of the U.S. power sector. Deployment of this technology can increase the reliability and decrease the cost of electricity generation in the U.S. by enabling the use of low-carbon fossil fuels to balance fluctuations of renewable energy availability.

03 NATURAL GAS↗

Maximizing long-term biohydrogen production with Clostridium thermocellum for high solids conversion of lignocellulosic biomass

Biological hydrogen production from lignocellulosic biomass sustainably couples organic waste reduction with renewable energy generation. Efficient conversion is challenged by the structural complexity of lignocellulose and resulting recalcitrance to enzymatic degradation. Clostridium thermocellum natively breaks down biomass with highly effective hemi-/cellulases systems (i.e., cellulosomes) and generates hydrogen in anaerobic cultivation, creating a compelling platform for lignocellulosic biohydrogen production. Achieving commercially viable production rates requires balancing high biomass loading and throughput against uniform mixing conditions required for enzyme dispersion, pH and temperature control, and efficient hydrogen and metabolite removal in continuous operation. To address these barriers to process intensification, we implemented novel reactor and process designs for high-solids lignocellulosic biomass fermentations using the C. thermocellum KJC19-9 strain, genetically engineered for co-utilization of cellulose and hemicellulose sugars (i.e., xylose). Via computational fluid dynamics (CFD) modeling and experimental validation, we achieved a >50% improvement in biohydrogen production with an improved anchor-type impeller morphology, coupled to a threefold reduction in agitation rate. To further reduce rheological constraints and accumulation of toxic metabolites, we then transitioned the process to sequencing fed-batch operation. The resulting process generated 24.87 L H 2 L −1 from 160 g L −1 of deacetylated and mechanically refined (DMR)-pretreated corn stover biomass over 16 days while solubilizing >95% of influent cellulose and hemicellulose, setting a new performance benchmark for continuous production of biohydrogen from lignocellulose.

08 HYDROGEN↗

3D printed structures for optimized carbon capture technology in packed bed columns

The use of 3D printed structured packing for the optimization of aqueous-amine based carbon capture in packed absorption columns is examined in this paper. An experimental testing system has been set up, and initial comparisons were made between metal, plastic, and 3D printed 16-inch packing elements and between three 8-inch 3D printed elements of different densities. Pressure drop measurements were obtained at various air flowrates under dry conditions. Measurements were also taken for a wet system by adding water at six different liquid flowrates. In each case, theoretical calculations for pressure drop were performed based on a model presented in the literature. It was found that, for the 16-inch dry column, the model slightly overpredicts the pressure drop. The model provides an accurate prediction for the dry 8-inch experimental data, especially for the two least dense packing elements. For the wet system, the model overpredicts the pressure drop, likely due to modeling deficiencies when the column reaches its loading limit. Furthermore, these results provide sufficient confidence to move forward with testing and process intensification of the CO 2 capture process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Hands-on Course on Intensified Membrane Processes for Sustainable Water Purification

The lack in process intensification (PI) training may be limiting processes to achieve sustainability goals. Furthermore, this project developed a hands-on course on intensified membrane processes to address knowledge gaps in PI. Bench-scale activities introduced concepts of membrane separation, operating engineering-scale modules provided a near-industrial experience, and simulation software allowed modeling and optimization of a process. Student evaluations showed that the combination of modeling, experimental, and peer-instruction work helped them understand the application of theoretical concepts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Biochemical Refining of Lignocellulose for Biofuels: Status and Prospects (Presentation)

Presentation describes progress to develop and demonstrate cost-competitive biochemical refining technologies, including recent progress at NREL to reduce the cost of converting cellulosic biomass to ethanol and new initiatives to convert biomass derived sugars to other advanced biofuels. The potential for process intensification to reduce capital equipment and process operating costs isillustrated. Remaining technical barriers and as-yet unrealized opportunities to stimulate biorefinery commercialization are discussed.

09 BIOMASS FUELS↗

Optimization of Graded Bed Reactors for Syngas to Olefin (STO) Processes

Reactor designs with mixed catalysts play an important role to transform a multiple reactor system to single-shot reactors. In addition to savings in capital and ease of implementation, single-shot reactors are useful to break equilibrium limitations, therefore increasing the yield and selectivity of desired product. However, the nonlinear, highly exothermic and poorly conditioned nature of mixed-catalyst systems makes it difficult for commercial process simulation and optimization tools to optimize these systems. Here, this study describes the zone and partial moving finite element approaches and their applications to o-xylene oxidation and syngas to olefin (STO) processes. 35% and 5% increases are achieved in the product yield for o-xylene oxidation and STO problems, respectively. Shown with these two examples, this tool is very promising in process intensification for other reactive systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

PERFORMANCE ANALYSIS OF AN ENGINEERING SCALE HYDROTHERMAL LIQUEFACTION SYSTEM

This work evaluates the Modular Hydrothermal Liquefaction System (MHTLS), an engineering-scale, integrated continuous HTL plant operated at the Pacific Northwest National Laboratory (PNNL), for converting realistic wet wastes into energy-dense biocrudes. The production campaigns discussed here processed algae, sewage sludges, lignocellulosic blends, Industrial food waste, and engineered food-waste slurries at 350?°C and around 200?bar, with nominal feed rates of ~12?L?h?¹. We report biocrude yields and composition, establish mass and elemental (C, N) balances, and quantify energy performance via heater duties, heat-exchanger behavior, and system-level efficiencies. Biocrudes contained 76–80?wt?% C (dry, ash-free) with HHVs of 38-41?MJ?kg?¹, substantially higher than feed materials HHVs of 16.6–26.1?MJ?kg?¹ and approaching petroleum fuels. Dry, ash-free biocrude yields of 32–53?wt?% corresponded to 43–71?wt?% carbon yields, with 18–40?wt?% of feed carbon routed to the aqueous phase. Thermal efficiencies were 50-65%, and total energy efficiencies, including reactor heat input, were 35-55%. A counter-current tube-in-tube heat exchanger delivered U values of 200–450?W?m?²?K?¹, with fouling-induced declines impacting heat recovery and heater duty. The analysis highlights three priorities for the process intensification of HTL: robust, fouling-resistant heat recovery, hydrodynamically suitable reactor and heat-exchanger designs, simplified and predictable solids management, and biocrude-water separation.

Biocrude production↗

Modular Plasma Microreactor for Intensified Hydrogen Peroxide Production

Sustainable and decentralized manufacturing of hydrogen peroxide (H 2 O 2 ) has been extensively sought to replace the energy- and waste-intensive anthraquinone process. We introduce a helical biphasic microreactor in a coaxial dielectric barrier discharge (DBD) configuration as a modular, adaptable, and scalable intensified unit for H 2 O 2 production. Geometric and operating parameters such as electrode length, applied voltage, and gas and liquid flow rates can be tuned to regulate the residence time, delivered power, and gas–liquid interfacial area. In turn, these affect the key output parameters, i.e., H 2 O 2 concentration, production rate, and energy yield. We found a direct correlation between the H 2 O 2 production rate and the product of the interfacial area and residence time in the plasma region. We investigated the H 2 O 2 formation pathways using DMSO as an ·OH radical scavenger and found that H 2 O 2 forms by the dissolution of gaseous H 2 O 2 at low interfacial areas and is enhanced probably due to the interfacial recombination of ·OH radicals at a large gas–liquid interfacial area. The reactor temperature can also be externally controlled to intensify the production rate and energy yield of H 2 O 2 . Concentrations of up to 33 mM can be attained with a small footprint reactor that features a maximum energy yield of 4 g kWh –1 . Here, the plasma microreactor could epitomize a powerful process intensification tool for sustainable and distributed chemical manufacturing.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Optimizing Selection Pressures and Pest Management to Maximize Cultivation Yield (OSPREY) (Final Technical Report)

This project was proposed in response to AOI 1, Cultivation Intensification Processes for Algae, within the FY19 Bioenergy Technologies Office Multi-Topic Funding Opportunity Announcement (FOA Number: DE-FOA-0002029). The work was designed to address a critical industry need to improve annualized productivity, stability, and quality of algal production strains for biofuels and bioproducts. The overall project goals were to generate process innovations rooted in established outdoor systems for strain selection, improvement, maintenance, and cultivation as well as pest detection and tracking. Planned advances included a 50% improvement in harvest yield based on AFDW (g m 2 d -1 ), 50% improvement in robustness based on stability metrics (e.g., high-productivity cultivation days, pond uptime), and 20% improvement in conversion yield. Individually, each of our planned process improvements (e.g., pest tracking) had the potential to increase productivity. However, to realize increases in yield at the system level, improvements to one unit’s process must be balanced against potential effects on other processes. For example, changes to strains, cultivation, and pest management developed in isolation may hurt other unit operations. Therefore, a critical success factor of the project was the integration of the pipeline components, achieved through iterative field-to- (short term) lab testing. In addition, through sustainability models, we evaluated how improvements would alter industry scenarios.

09 BIOMASS FUELS↗

Continuous enzymatic hydrolysis of lignocellulosic biomass in a membrane-reactor system: Continuous enzymatic hydrolysis of lignocellulosic biomass in a membrane-reactor system

Converting abundant lignocellulosic biomass to sugars as fungible precursors to fuels and chemicals has the potential to diversify the supply chain for those products, but further process improvements are needed to achieve economic viability. In the current work, process intensification of the key enzymatic hydrolysis unit operation is demonstrated by means of a membrane reactor system that was operated continuously. Lignocellulosic biomass (pretreated corn stover) and buffered enzyme solution were fed to a continuously stirred-tank reactor, and clarified sugar solution was withdrawn via a commercial tubular ultrafiltration membrane. The membrane permeance decline and membrane cleaning efficacy were studied and did not vary significantly when increasing fraction insoluble solids (FIS) from 2.5% to 5%. Continuous enzymatic hydrolysis was successfully operated for more than 80 h. A model for the reactor system was able to predict dynamic behavior that was in reasonable agreement with experimental results. The modeled technical performance of anticipated commercial batch and continuous enzymatic hydrolysis processes were compared and showed that continuous operation would provide at least twice the volumetric productivity for the conditions studied. Further improvements are anticipated by better membrane selection and by increasing FIS.

09 BIOMASS FUELS↗

Intensified Co-electrolysis Process for Syngas Production from Captured CO 2

CO 2 reduction to syngas provides a way of ameliorating carbon footprint and storing energy in high-energy-density and versatile feedstock. This current work explores the isothermal integration of CO2 capture with an intensified unit operation for the reduction of CO2 and capture media regeneration. Intensified captured CO2 co-electrolysis (ICC) to syngas (H2:CO ratio of 2) with low CO2 content (<10%) was demonstrated with over 70% CO2 conversion at a current density up to 0.20 A/cm2 for 14 hours of operation. Integration of the co-electrolysis unit with CO2 capture was performed feeding pure and diluted CO2, for which CO2 conversions >65% were observed. Performance of the capture unit becomes critical to maintain syngas ratios (SR). Technology feasibility was assessed through comparative techno-economic and life cycle analysis showing that process intensification enables competitive performance, even at the higher energy consumption featured at the current state of the technology. This because several unit operations can be avoided. LCA also showed that based on the current US electricity mix the reduction of life cycle CO2 emissions is possible at scenarios observed with 0.15 A/cm2 to accomplish a carbon-negative technology.

08 HYDROGEN↗

Conventional and autothermal pyrolysis of corn stover: Overcoming the processing challenges of high-ash agricultural residues

The high ash content of agricultural residues and other kinds of herbaceous biomass makes it a challenging feedstock for fast pyrolysis to bio-oil. Using corn stover as a representative feedstock, this study investigates fast pyrolysis of high ash, herbaceous biomass in a pilot-scale fluidized bed reactor using both conventional, nitrogen-blown and autothermal, air-blown operation. Initial efforts to pyrolyze corn stover were challenged by bed fouling, which prevented steady reactor operation. Substitution of coarser bed material allowed operation at higher superficial velocities, which promoted attrition and elutriation of recalcitrant biochar particles from the reactor. This resulted in dramatic improvement in stable reactor operation for both conventional and autothermal pyrolysis with bio-oil yields among the highest reported for pyrolysis of corn stover. The oxygen-to-biomass equivalence ratio required for autothermal operation was 6.8%. Autothermal operation also resulted in significant process intensification, increasing corn stover throughput from 7.8 kg hr –1 to 21.9 kg hr –1 for this 8.9 cm diameter reactor. Air-blown, autothermal operation did not significantly reduce bio-oil yield despite the presence of partial oxidation reactions. In conclusion, carbon balances indicate carbon yields of biochar and aqueous, bio-oil light ends decreased by 18.5% and 4.7%, respectively, during autothermal pyrolysis compared to conventional pyrolysis while the more valuable, organic-rich heavy ends of the bio-oil were essentially preserved.

09 BIOMASS FUELS↗

ROTA-CAP™: An Intensified Carbon Capture System Using Rotating Packed Beds (Final Scientific/Technical Report)

GTI Energy and Carbon Clean Solutions Limited successfully designed, constructed, and operated an integrated ROTA-CAP carbon capture skid. ROTA-CAP™ is a process intensification technology, applied for post-combustion carbon capture, which utilizes the centrifugal forces generated from rotation of rotating packed beds as well as advanced solvents to achieve increased mass transfer rates 1-2 orders of magnitude higher than conventional columns while substantially decreasing footprint. The test skid, which consisted of a dual stage RPB absorber with external interstage cooling and a single stage RPB regenerator, was operated at capacities up to 0.5 tonne/day of CO 2 capture with flue gas concentrations ranging from 4% to 22% CO 2 by vol. CO 2 removal rates greater than 95% were achieved, with CO 2 product purity also exceeding 95% by vol. Over 1,600 hours of operation were accumulated throughout the project, including over 1,000 hours of operation of the with real flue gas containing at least 9.8% CO 2 by vol. The skid was operated continuously for 24 hours per day and 7 days per week over the course of 7 long-term test campaigns, with the campaigns ranging from approximately 2-4 weeks per campaign. A techno-economic analysis was performed, and a cost of capture of $\$$41.18/tonne CO 2 was calculated for the ROTA-CAP process, compared to $\$$45.75/tonne for a Cansolv-based process. These results show a cost reduction of approximately 10% compared to the Cansolv-based process. Although this still exceeds the target cost of capture of $\$$30/tonne specified for this project, GTI expects that the cost of capture can be further reduced through further optimization of the design and technology. GTI also performed an engineering design review to determine the scale-up potential of the technology, with the results of the preliminary assessment indicating that it appears to be feasible to scale up the RPB technology to 4,000 TPD. It was also determined that both horizontal and vertical rotor orientations are feasible, though there are mechanical advantages to the vertical orientation.

20 FOSSIL-FUELED POWER PLANTS↗

Additively manufactured cryogenic microchannel distillation device for air separation

Abstract The efficiency of air separation is tested using three different small‐scale cryogenic distillation columns. The performance of a random packed column is compared to the performance of two microchannel distillation (MCD) columns that use thin wicking structures and gas flow channels to achieve process intensification. The MCD columns tested include a plate‐type layered column and an additively manufactured porous honeycomb (AMPH) column. For columns with 25.4 cm of active height and run under similar conditions, the packed, plate‐type layering, and AMPH columns achieved approximate height equivalent of a theoretical plate (HETP) values of 5.5, 3.7, and 3.2 cm for nitrogen, and 5.9, 4.9, and 3.3 cm for argon. The AMPH column can produce up to 0.4 SLM of more than 90% purity oxygen with 12 W of cooling lift. These results demonstrate the feasibility of using additive manufacturing to construct MCD devices and pave a way for constructing novel MCD designs.

36 MATERIALS SCIENCE↗

Influence of design and operating parameters for additively manufactured intensified packing devices on CO 2 -Absorption column cooling and capture efficiency

Solvent-based CO 2 absorption is technologically a matured CO 2 capture pathway but suffers from: high regeneration energy demand, and solvent temperature rise and decreased capture efficiency caused by the heat of reaction. While research has focused on developing non-aqueous and low-aqueous solvents for decreasing the regeneration energy, the temperature bulge due to exothermic absorption is typically dealt with by cooling the solvent with an external inter-stage heat-exchanger. This approach may increase the overall process footprint, as well as capital and operating costs. Here, the current study explores a process intensification approach by incorporating inside the column an additively manufactured intensified packing device that consists of corrugated plates and internal coolant channels. The corrugated plates provide surface area for mass transfer between gas and liquid, while cooling fluid inside the internal channels removes heat from the exothermic reactive system. Two different intensified devices with specific surface areas of 266 m 2 /m 3 and 359 m 2 /m 3 were designed, manufactured, and tested inside a 2.06-m long and 0.203-m diameter column packed with commercial Mellapak 250Y packing. The device with a lower surface area showed up to 27 % reduction in cooling performance. A steady-state heat transfer model provides good agreement with the experimental column temperature and intra-stage heat removal data. Although a decrease in heat transfer performance was observed for the device with lower surface area, CO 2 capture experiments performed with simulated flue gas and low-aqueous solvent demonstrated that both intensified devices lead to a similar improvement of 12 % in capture efficiency. This study provides an understanding on simplifying the intensified packing device geometry and decreasing the device fabrication cost by 25 % without compromising with the CO 2 absorption performance of the packed column.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Modular Adaptive Packing for Integrally Cooled Absorbers

Process intensification is one cornerstone in ION Clean Energy’s (ION) efforts to lowering CO2 capture cost. ION has modeled, designed, and fabricated an innovative gas-liquid contactor known as Modular Adaptive Packing (MAP). During two successful SBIR Phase I and II projects entitled: “Rapid Design and Testing of Novel Gas-Liquid Contacting Devices for Post-Combustion CO2 Capture via 3D-printing”, ION developed and proved this new technology at bench scale. MAP, a 3D-printed lattice-structured packing, combines the absorber gas/liquid contactor with an innovative in-situ heat-exchanger. Thanks to the capabilities of 3D-printing, the lattice structure of MAP contains hollow channels through which coolant water can be pumped to remove the heat of reaction from CO2 absorption. ION refers to this novel method of heat exchange as intracooling. After 25.4 cm (10 in) diameter MAP modules were fabricated, ION built and tested a packing characterization rig at its pilot facility in Boulder, Colorado, U.S.A. To provide baseline results for the characterization rig, ION tested Sulzer’s Mellapak™ 250Y (MP250Y) as a standard structured packing. ION’s MAP was then compared directly to the baseline MP250Y packing to evaluate key indicators including pressure drop, liquid hold-up, and effective area. MAP has a higher pressure drop than MP250Y at the same gas velocities in addition to greater liquid holdup. However, ION found that MAP displays a higher wetting coverage of 93% compared to 65% for MP250Y and reduces shearing forces that result in undesirable droplet formation. Using Optimized Gas Treating’s (OGT) rate-based simulation software ProTreat®, a conceptual evaluation of MAP was modeled for a CO2 absorber using 30 wt% MEA solvent over a range of lean loadings at 90% CO2 capture from a coal-fired power plant. ION modeled a 25-meter column absorber for both the standard MP250Y packing and a hybrid column. The hybrid absorber contained 10 m of MP250Y packing at the top and bottom with the middle 5 meters comprised of MAP. Compared to a traditional intercooled absorber, MAP can remove 22% more heat and increase overall MEA carrying capacity by 4% without increasing overall pressure drop.

20 FOSSIL-FUELED POWER PLANTS↗

Manufacturing Supply Chain Development for Modular Solar-Thermochemical Conversion Platform - CRADA 387 (Final Report)

Modular chemical process intensification (MCPI) is an emerging field where chemical processing is performed using small-scale modular equipment instead of conventional large centralized chemical plants. Conventional chemical plants benefit from economies of scale that encourage scale-up to ever larger plants. A goal of MCPI is to develop technology that intensifies processing so that equipment can be dramatically smaller and integrated into modular systems. Scale-up occurs by adding more modules in parallel rather than making the equipment larger. A key concept is that equipment and modules can ultimately be cheaper by leveraging economies of mass production, analogous to the automotive industry, in manufacturing the equipment. This project made significant progress toward this outcome by meeting the RAPID institute metric to reduce equipment cost by 20% for each doubling in manufacturing volume. The MCPI application was thermochemical technology that is being commercialized by STARS Technology Corporation, one of the CRADA partners. The technology converts solar and renewable power to chemical energy to produce renewable hydrogen, fuels, and chemicals. The benefit to the public is reduction in greenhouse gases that are contributing to climate change. The project transitioned the steam methane reforming (SMR) reactor from conventional fabrication methods to additive manufacturing (AM) direct metal laser sintering (DMLS) process. This is projected to reduce the cost of making a reactor by 58% when producing 100 reactors per year. Innovations in the DMLS process produced a patented design that reduces reactor weight by 60%. Reductions in material costs and processing time extend the DMLS advantage to higher production volumes. The new design promises to be 38% cheaper than the conventional processes at 1000 units per year. The resulting 87% reduction in the steam methane reforming (SMR) module cost in scaling from current costs meets the RAPID metric. The project was successful in producing and testing the first ever additively manufactured SMR reactors. A reactor achieved over 82% efficiency in converting electric power to chemical energy, which is a world record for an inductively heated SMR. The project has contributed to the design and assembly of a first demonstration plant that is headed to a hydrogen bus filling station in Thousand Palms, CA.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Ultrafast flow chemistry for the acid-catalyzed conversion of fructose

Biomass conversion to chemicals and fuels has been epitomized by batch processing and long reaction times that limit the economic viability of future biorefineries and prevent modular manufacturing near the source-production site that is necessary due to the biomass’ large water content. Herein we introduce a continuous flow microreactor to enable process intensification and one thousand-fold device miniaturization for remote chemical processing. We demonstrate the approach in HCl-catalyzed fructose dehydration in water. We characterize and quantify the mixing using laser induced fluorescence (LIF) of fluorescent dyes and particle image velocimetry (PIV) of fluorescent microspheres. The estimated mixing times ranged from 0.03 to 4.8 s for residence times from 1 to 120 s, respectively. Moreover, a curved channel geometry induces secondary (Dean) vortices that produce a three-fold increase in mixing by diffusion through advection along the cross-sectional direction of the channel, creating dissipative chaotic mixing under laminar flow. We then obtain for the first time isothermal kinetics of fructose dehydration at short contact times and high temperatures and compare to a previously published, hybrid ab initio and data-driven kinetic model. Rigorous model optimization is carried out and an optimal HMF yield of 54% is attained in a single aqueous phase. High temperatures and low pH improve the reactor throughput by increasing the HMF space-time yield. We demonstrate the highest ever productivity (HMF yield per unit time). Importantly, this can be achieved at ~100% fructose conversion, eliminating the need for recycling to improve economics. Furthermore, optimization of the reactor dimensions and the specific energy dissipation rate results in ~60% pressure-drop related energy savings. We describe a methodology to scale-up microreactors to millimeter size and increase productivity 16-fold under optimal conditions. The energy efficiency and cost analysis for HMF production from corn stover of a typical corn farm indicate an optimal strategy for numbering-up millimeter size reactors and, importantly, they underscore the potential feasibility of producing bioproducts in a distributed manner.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗