SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A chemical fraction enriched in cyclic ketones, was isolated from ex situ catalytic fast pyrolysis (CFP) bio-oil and valorized to hydroxy and dicarboxylic acids by an engineered Pseudomonas putida strain.
Methane catalytic pyrolysis, which is the reaction to produce hydrogen and carbon without emitting CO 2 , represents an approach for decarbonization using natural gas as an energy resource. In this work, the endothermic pyrolysis reaction was carried out under two heating scenarios: convective thermal heating and microwave-driven irradiative heating. The pyrolysis reaction was conducted at 550-600 °C over carbon nanotube-supported Ni-Pd and Ni-Cu catalysts. On both catalysts, an enhanced methane conversion rate was observed under microwave irradiation. The enhanced catalytic activity was hypothetically caused by the presence of free electrons in the carbon atoms within CNT that enabled the CNT support to absorb microwave energy effectively and to be heated efficiently by microwave. The microwave catalytic pyrolysis has shown improvement in kinetics, where the apparent activation energy dropped from 45.5 kJ/mol under conventional convective heating to 24.8 kJ/mol under microwave irradiation. When the methane conversion rate is increased by 37 %, the microwave power consumption only changed by 10.8 %. The research demonstrated the potential of transforming natural gas to clean hydrogen and value-added carbon in a more energy-efficient way. Process simulation and techno-economic analysis showed that potentially hydrogen minimum selling price of about $1 /kg H 2 could be achieved.
Pyrolysis of lignocellulosic biomass can serve as a powerful pathway for the generation of renewable fuels and industrial products. However, procurement of some biomass may be costly, especially when there is competition for alternative uses. Forestry and agricultural byproducts may serve as valuable pyrolysis feedstocks due to their high availability and low cost. Although waste products may fill demand for affordable pyrolysis feedstocks, they are often high in ash and extractives which contribute to unfavorable changes in pyrolysis vapor composition, as well as end products. The work presented here investigates the correlations between various pine anatomical fractions to understand their effect on pyrolysis oil composition for forest residues. Analytical pyrolysis coupled to direct analysis by molecular beam mass spectrometry (MBMS) provides real-time monitoring of pyrolysis vapor composition, even for compounds that are not amenable to gas chromatography. Statistical analysis of MBMS data from the fast pyrolysis (FP) of clean pine, cambium, twigs and branches, needles, bark, and a forest residue samples revealed that bark and needles made the greatest differences in the vapor composition of forest residues during pyrolysis and were enriched in resin acids, furfural derivatives, and ions that have been previously observed from catalysis corresponding to ash content. These results were also compared to catalytic fast pyrolysis (CFP) using a platinum on titania catalyst, and correlations between FP and CFP products were observed for the anatomical fractions. The forest residues and corresponding anatomical fractions from a stand of 23-year-old pine will be converted by fast pyrolysis in a bench-scale 2-inch fluidized-bed reactor, and statistical correlations between the bench-scale products and analytical-scale pyrolysis vapors will be shown. This work highlights the power of advanced analytical methodologies in determining the contributions of vapor components to catalytic pyrolysis outcomes for mixed feedstocks and demonstrates the use of analytical methodologies to better screen feedstocks prior to pyrolysis.
Efficient utilization of biomass is challenging due to the complexity of the feedstock at molecular, particle, and reactor scales. Direct coupling of particle scale model and reactor scale simulation is computationally infeasible. In this work, the results from a particle resolved simulation were used to calibrate the heat transfer and reaction kinetics of particles. A hybrid drag model was used to consider the different fluidization properties of sands and biomass particles. The computation cost was reduced using a coarse-grained Discrete Element Method (DEM). The simulated conversion rate, char yield, tar yield, and pyrolysis gas yield compare well with experiment. The residence time and axial distributions of biomass were also analyzed. This novel multi-scale method provides an efficient and accurate tool for the modeling of biomass pyrolysis reactors.
A model for the fast pyrolysis of anisotropic biomass particles is presented which considers bubbling dynamics within the liquid intermediate phase (metaplast) and aerosol ejection from this phase. The model employs the population balance equation and the method of moments to estimate the production rate and resultant size distribution of aerosol ejections, incorporating a detailed CRECK reaction mechanism, and considers the effect of anisotropic biomass microstructure on the intraparticle transport of mass and energy. Here, this study investigates the impact of particle size, heating rate (heat transfer coefficient), and lignocellulosic composition on aerosol ejection. The model predicts that, at high heating rates (convective heat transfer coefficient of 359 W/m 2 .K), aerosols can contribute over 20% to the heavy fraction yield in bio-oil for small particles (1 mm diameter, 4 mm length). The model can predict aerosol size distribution and surface area, indicating an average size of 20 μm for bubbles and 5 μm for aerosols during increased bubble production and aerosol ejection rates. These findings are consistent with prior experimental results and provide essential information for future modeling of extra-particle reactions of the aerosols as they progress through the reactor.
A detailed biomass pyrolysis kinetic scheme was assessed in the multiscale simulations of a single-particle pyrolyzer with slow pyrolysis and a pilot-scale entrained flow pyrolyzer with fast pyrolysis. The detailed kinetic scheme of biomass pyrolysis developed by the CRECK group consists of 32 reactions and 58 species. A multiscale simulation model was developed, where the CRECK kinetics was employed to simulate biomass pyrolysis reactions, a one-dimensional particle model was utilized to simulate the intraparticle transport phenomena, and the particle-in-cell (PIC) model was employed to simulate the hydrodynamics. The multiscale model was first applied to simulate a single-particle pyrolysis experiment. The simulation with nonisothermal particles matched the experimental data better than the simulation with isothermal particles. Then the multiscale model was applied to simulate the pilot-scale entrained flow pyrolyzer. In this case, the simulation with isothermal particles matched the experimental data better than the simulation with nonisothermal particles. The reason for this difference might be that the kinetics itself already partially included the intraparticle transport effect as it was fitted using both TGA data (slow pyrolysis of small size biomass) and fluidized bed data (fast pyrolysis of relatively large size biomass). This study provides some insights into biomass pyrolysis kinetics development and pyrolyzer multiscale simulation for a future study.
Carboxylic acids are important combustion intermediates, especially regarding the combustion of oxygenates such as ethyl esters. The purpose of this study is to discern the unimolecular decomposition pathways of one such carboxylic acid, propionic acid, using microreactor flow experiments with line-tunable photoionization mass spectrometry and infrared spectroscopy, along with high-level electronic structure calculations (CCSD(T)/cc-pV∞Z//M06-2X/cc-pVTZ level of theory) and master equation theory. Here, microreactor experiments were performed at 300–1500 K, pressures decreasing from roughly 300 Torr to vacuum pressure, and around 100 μs residence times. Primary products are methyl ketene, ketene, ethylene, and methyl radical. Theory suggests the two lowest energy bond fissions are active at these conditions and responsible for the production of ketene, methyl radical, and some ethylene. Importantly, theory revealed the significance of the isomerization of propionic acid to propene-1,1-diol, and the subsequent dehydrogenation reaction of the diol as an alternative explanation for the unimolecular formation of methyl ketene. This is predicted to be the dominant thermal decomposition pathway at lower temperatures (up to ~850 K). Line-tunable VUV photons allowed for isomer resolution of the products and showed no evidence of the diol of propionic acid surviving until detection, suggesting propene-1,1-diol decomposes either to methyl ketene and water rapidly, fragments upon ionization to a distonic ion inseparable from methyl ketene through our detection methods, or never stabilizes as propionic acid well-skips directly to methyl ketene. Infrared spectroscopy showed no evidence of the decarboxylation of propionic acid at these conditions. Updated rate constants and branching ratios for propionic acid decomposition are calculated and provided for future modeling studies.
This study demonstrates that coupling of a material thermal response code and a flow solver using non-equilibrium gas/surface interaction model provides time-accurate solutions for the multidimensional ablation of carbon based charring ablators. The material thermal response code used in this study is the Two-dimensional Implicit Thermal-response and AblatioN Program (TITAN), which predicts charring material thermal response and shape change on hypersonic space vehicles. Its governing equations include total energy balance, pyrolysis gas mass conservation, and a three-component decomposition model. The flow code solves the reacting Navier-Stokes equations using Data Parallel Line Relaxation (DPLR) method. Loose coupling between the material response and flow codes is performed by solving the surface mass balance in DPLR and the surface energy balance in TITAN. Thus, the material surface recession is predicted by finite-rate gas/surface interaction boundary conditions implemented in DPLR, and the surface temperature and pyrolysis gas injection rate are computed in TITAN. Two sets of nonequilibrium gas/surface interaction chemistry between air and the carbon surface developed by Park and Zhluktov, respectively, are studied. Coupled fluid-material response analyses of stagnation tests conducted in NASA Ames Research Center arc-jet facilities are considered. The ablating material used in these arc-jet tests was Phenolic Impregnated Carbon Ablator (PICA). Computational predictions of in-depth material thermal response and surface recession are compared with the experimental measurements for stagnation cold wall heat flux ranging from 107 to 1100 Watts per square centimeter.
Plastic waste is an emerging environmental issue for our society. Critical action to tackle this problem is to upcycle plastic waste as valuable feedstock. Thermochemical conversion of plastic waste has received growing attention. Although thermochemical conversion is promising for handling mixed plastic waste, it typically occurs at high temperatures (300–800 °C). Catalysts can play a critical role in improving the energy efficiency of thermochemical conversion, promoting targeted reactions, and improving product selectivity. Here this Review aims to summarize the state-of-the-art of catalytic thermochemical conversions of various types of plastic waste. First, general trends and recent development of catalytic thermochemical conversions including pyrolysis, gasification, hydrothermal processes, and chemolysis of plastic waste into fuels, chemicals, and value-added materials were reviewed. Second, the status quo for the commercial implementation of thermochemical conversion of plastic waste was summarized. Finally, the current challenges and future perspectives of catalytic thermochemical conversion of plastic waste including the design of sustainable and robust catalysts were discussed.
The Mars Science Laboratory (MSL) Curiosity Rover carries a suite of instruments, one of which is the Sample Analysis at Mars (SAM) experiment. SAM is devoted to the in situ molecular analysis of gases evolving from solid samples collected by Curiosity on Mars surface/sub-surface. Among its three analytical devices, SAM has a gaschromatograph coupled to a quadrupole mass spectrometer (GC-QMS). The GC-QMS is devoted to the separation and identification of organic and inorganic material. Before proceeding to the GC-QMS analysis, the solid sample collected by Curiosity is subjected to a thermal treatment thanks to the pyrolysis oven to release the volatiles into the gas processing system. Depending on the sample, a derivatization method by wet chemistry: MTBSTFA of TMAH can also be applied to analyze the most refractory compounds. The GC is able to separate the organic molecules which are then detected and identified by the QMS (Figure 1). For the second time after the Viking landers in 1976, SAM detected chlorinated organic compounds with the pyrolysis GC-QMS experiment. The detection of perchlorates salts (ClO4-) in soil at the Phoenix Landing site suggests that the chlorohydrocarbons detected could come from the reaction of organics with oxychlorines. Indeed, laboratory pyrolysis experiments have demonstrated that oxychlorines decomposed into molecular oxygen and volatile chlorine (HCl and/or Cl2) when heated which then react with the organic matter in the solid samples by oxidation and/or chlorination processes.
The hydrolysis of cellulose to high-yield glucose in water remains challenging owing to the limited acidity and substrate contact of sulfonated carbons. In this study, we report a unique sulfonated mesoporous carbon fiber with optimized acidity prepared by the pyrolysis of FeCl 3 -impregnated wipe fibers followed by acid treatment. The Bronsted acidity (especially for SO 3 H) was produced by sulfonation of the magnetic carbon fiber intermediate, while Lewis acidity originated from small Fe 3 O 4 nanoparticles and the remaining defects. The balanced Bronsted and Lewis acidity combined with hydrophilic functionalities was simultaneously tailored by varying the Fe/wipe fiber (WF) feed ratio and pyrolysis temperature to change the porous structure of the final catalysts. The elaborately fabricated MCF-SO 3 H-20-500 (20% Fe/WF feed ratio and pyrolysis at 500 degrees C) delivered 66.0% glucose yield as cellulose was completely converted. This is the highest glucose yield achieved by the hydrolysis of untreated cellulose in water over a sulfonated carbon catalyst. The optimized Bronsted and Lewis acidity was mainly responsible for the controlled conversion of cellulose to glucose, while the rich hydrophilic functionalities and superior mesoporous structure of the catalyst facilitated contact to cellulose and mass transfer. This investigation will open new avenues to design high-performance carbon sulfoacid catalysts toward cellulose hydrolysis.
Luna 16 and Luna 20 samples were analyzed for volatilizable species using vacuum pyrolysis to 1400 C. The major gaseous products evolved (ranging from 10-650 micrograms/g) were H2O, CO, CO2, N2 and CH4. Minor components (all less than 10 micrograms/g) included NH3, HCN, NO, SO2, H2S, C2H2, C2H4, C2H6, C3H6 and higher hydrocarbons, benzene, toluene, and the polymeric contaminants Teflon and silicone oil. The total carbon and nitrogen contents (micrograms/g) for these sieved samples were: Luna 16 - C 418, N 134 and Luna 20 - C 380, N 80.
Preceramic polymers (PCPs) offer advantages in producing ceramics due to their processability and ability to tailor the final chemistry of the produced material. However, challenges such as volumetric shrinkage and mass loss during pyrolysis often result in polymer-derived ceramics containing pores and cracks. PCP-grafted ceramic nanoparticles (PCPGNPs) have been proposed and studied as a route to mitigate the shrinkage issues associated with neat PCPs. Prior studies on PCPGNPs have principally focused on the synthesis and characterization of neat materials. Dispersing PCPGNPs in commercial preceramic polymer is another attractive, but underexplored, route to control the rheological and char yield properties of PCP systems. In this work, a systematic rheological study of commercial PCP (SMP-877) and PCPGNP (silica with poly(1,1-dimethylpropylsilane) corona) mixtures was executed to develop design rules for the processing of such systems. A rheological study demonstrated the effect of increasing particle concentration on network formation with percolation occurring between 50 and 60 wt %. Samples above the percolation threshold exhibited higher viscosities and rapid shear thinning thus demonstrating their direct-write printability. X-ray photon correlation spectroscopy (XPCS) corroborated the rheology and showed two diffusive modes when the material was above percolation. Mixtures of PCPGNPs and SMP-877 had synergistically higher char yields upon thermal treatment and pyrolysis. XPCS and rheological measurements during thermal treatment identified thermal jamming of the polymer grafts as a key factor in improving the char yield. In conclusion, with the insights gained here, we expect these mixed systems to provide attractive feedstocks for polymer-derived ceramics, with proof-of-principal application as feedstocks for direct ink write (DIW) additive manufacturing.
In this paper, we study the kinetics of polyvinyl chloride (PVC) decomposition using a combination of experimental and computational approaches. Here, we develop a simplified kinetic model that contains only two steps: dehydrochlorination of PVC and further decomposition of the PVC residue. The model is consistent with density functional theory (DFT) calculations and experimental data. Dehydrochlorination is an autocatalytic reaction that starts with a tertiary chloride (Cl) and generates hydrogen chloride (HCl) and benzene as the main products. Benzene and HCl formation rates showed similar trends, indicating that HCl likely catalyzes a homolytic carbon-carbon (C-C) bond cleavage, which gives rise to benzene and an aliphatic fragment. We characterized the structure of dehydrochlorinated PVC (PVC residue) by using thermal gravimetric analysis (TGA), Fourier-transform infrared spectroscopy (FTIR), and nuclear magnetic resonance spectroscopy (NMR). FTIR and NMR results indicate that the PVC residue contains 20% quaternary carbon content, indicating a high concentration of cross-linked molecules. We predict that the most probable structure in the cross-linked centers of the PVC residue is cyclohexadiene, which is supported by DFT calculations, FTIR, and NMR.
Abstract: Non- equilibrium plasma assisted kinetics of ethanol at 0.5 atm over a temperature range of 523-1203 K were studied at stoichiometric conditions by using a plasma flow reactor (PFR). The effects of plasma chemistry on fuel and its influence on neutral chemistry is decoupled with both experimental and modelling efforts. Enhanced reactivity was observed experimentally in both plasma-assisted oxidation and pyrolysis cases with fuel consumption beginning at temperatures as low as 523 K. Absolute fuel consumption was observed at temperatures nearly 200 K earlier than pure thermal reactions highlighting the effectiveness of non-equilibrium plasma to promote reactivity. Modelling results illustrated the effect of electron impact reactions towards accelerating fuel consumption and promoting low temperature chemistry by generating excited state N2 and reactive O and OH radicals.
Pyrolysis is a promising technology for converting plastic waste into valuable raw materials while offering a potential solution to the global plastic pollution crisis. In this study, the thermal pyrolysis of high-density polyethylene (HDPE) is investigated in a drop tube reactor under nearly isothermal conditions. The impact of reaction temperature and gas/volatile residence time on carbon conversion and product distribution is examined across a range of 500–900°C and 3.6–32.2s, respectively. Non-condensable gas products detected by online mass spectrometry are H 2 , CH 4 , C 2 H 4 , C 2 H 6 , C 3 H 6 , and C 3 H 8 . At elevated temperatures and prolonged residence time, H 2 yield reaches as high as 8.6 wt% of the initial HDPE mass due to intensified cracking reactions of C 2 –C 3 hydrocarbons and long-chain aliphatic compounds. Consequently, pyrolysis tars consist mainly of polycyclic aromatic hydrocarbons (PAHs) with 5–7 rings, accompanied by visible coke deposition within the reactor. HDPE decomposition to volatiles is an endothermic process and it is complete at a temperature between 492°C and 525°C, depending on the heating rate employed, from non-isothermal thermogravimetric analysis and differential scanning calorimetry (TGA-DSC) measurements. The thermal degradation of HDPE pellets follows the two-dimensional nucleation growth model for conversion levels up to 0.8 with an apparent activation energy of 259–270 kJ/mol and a pre-exponential factor of 4.83 × 10 17 –1.37 × 10 19 min -1 , determined from various isoconversional methods such as Flynn-Wall-Ozawa (FWO), Kissinger-Akahira-Sunose (KAS), and Starink, along with Criado's master plots. Further, these findings provide valuable insights into optimizing process parameters and refining reactor design for pyrolysis, which can be integrated with gasification and reforming processes to enhance hydrogen production on a larger scale.
The Sampl;e Analysis at Mars (sam) instrument suite on the Mars Science Laboratory (MSL) Curiosity Rover detected both reduced and oxidized nitrogen bearing compounds during the pyrolysis of surface materials from the three sites at Gale Crater. Preliminary detections of nitrogen species include No, HCN, ClCN, and TFMA ((trifluoro-N-methyl-acetamide), Confirmation of indigenous Martian nitrogen-bearing compounds requires quantifying N contribution from the terrestrial derivatization reagents carried for SAM's wet chemistry experiment that contribute to the SAM background. Nitrogen species detected in the SAM solid sample analyses can also be produced during laboratory pyrolysis experiments where these reagents are heated in the presence of perchlorate a compound that has also been identified by SAM in Mars solid samples.
We endeavor to develop and implement methods in our laboratory to convert and extract insoluble organic materials (IOM) from low car-bon bearing meteorites (such as ordinary chondrites) and Precambrian terrestrial rocks for the purpose of determining IOM structure and prebiotic chemistries preserved in these types of samples. The general scheme of converting and extracting IOM in samples is summarized in Figure 1. First, powdered samples are solvent extracted in a micro-Soxhlet apparatus multiple times using solvents ranging from non-polar to polar (hexane - non-polar, dichloromethane - non-polar to polar, methanol - polar protic, and acetonitrile - polar aprotic). Second, solid residue from solvent extractions is processed using strong acids, hydrochloric and hydrofluoric, to dissolve minerals and isolate IOM. Third, the isolated IOM is subjected to both thermal (pyrolysis) and chemical (oxidation) degradation to release compounds from the macromolecular material. Finally, products from oxidation and pyrolysis are analyzed by gas chromatography - mass spectrometry (GCMS). We are working toward an integrated method and analysis scheme that will allow us to determine prebiotic chemistries in ordinary chondrites and Precambrian terrestrial rocks. Powerful techniques that we are including are stepwise, flash, and gradual pyrolysis and ruthenium tetroxide oxidation. More details of the integrated scheme will be presented.