Search NASA⌕ Search

SEARCH · Search NASA

Results for “resistance surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Evaluating the Effects of Nitrogen Doping and Oxygen Doping on SRF Cavity Performance

Superconducting radiofrequency (SRF) cavities are resonators with extremely low surface resistance that enable accelerating cavities to have extremely high quality factors (Q₀). High Q₀ decreases the capital required to keep the accelerators cold by reducing power loss. The performance of SRF cavities is largely governed by the surface composition of the first §I{100}{nm} of the cavity surface. Impurities such as oxygen and nitrogen have been observed to yield high Q₀, but their precise roles are still being studied. Here, we compare the performance of cavities doped with nitrogen and oxygen in terms of surface composition and heating behavior with field. A simulation of the diffusion of oxygen into the bulk of the cavity was built using COMSOL Multiphysics software. Simulated results were compared to the actual surface composition of the cavities as determined from secondary ion mass spectrometry analysis. Understanding how these impurities affects performance allows us to have further insight into the underlying mechanisms that enable these surface treatments to yield high Q₀.

43 PARTICLE ACCELERATORS↗
NASA NTRS1973

Effects of atmospheric moisture on rock resistivity.

This study examines the changes in resistivity of rock samples as induced by atmospheric moisture. Experiments were performed on samples of hematitic sandstone, pyrite, and galena. The sandstone underwent a change in resistivity of four orders of magnitude when it was measured in a vacuum of 500 ntorr and in air of 37% relative humidity. Pyrite and galena showed no variations in resistivity when they were measured under the same conditions. These results, plus others obtained elsewhere, indicate that rocks of the resistive type are affected in their electrical properties by atmospheric moisture, whereas rocks of the conductive type are not. The experimental evidence obtained is difficult to reconcile with a model of aqueous electrolytic conduction on the sample surface. It is instead suggested that adsorbed water molecules alter the surface resistivity in a manner similar to that observed in semiconductors and insulators.

Alvarez, R.↗
DOE OSTI2022

Characterization of Nb films with varying RRR values at low temperatures [Poster]

Superconducting properties of Nb in microwave fields vary significantly with lattice defects and impurity content, where sub-at.% impurity level can reduce or increase microwave surface resistance by an order of magnitude. In this study, we studied the microwave properties of Nb films, deposited by different PVD techniques, at low microwave fields correlating microwave properties at dilution fridge temperatures with material properties characterized with surface science techniques. We are studying the microwave properties of Nb films, deposited by different PVD techniques, at low microwave fields and low temperatures. The first Nb film, deposited onto an elliptical niobium cavity by HiPIMS technique at CERN, was tested at low temperatures. The first results show that film performance was similar to that of the bulk niobium cavities.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS2011

Nanoscale Metal Oxide Semiconductors for Gas Sensing

A report describes the fabrication and testing of nanoscale metal oxide semiconductors (MOSs) for gas and chemical sensing. This document examines the relationship between processing approaches and resulting sensor behavior. This is a core question related to a range of applications of nanotechnology and a number of different synthesis methods are discussed: thermal evaporation- condensation (TEC), controlled oxidation, and electrospinning. Advantages and limitations of each technique are listed, providing a processing overview to developers of nanotechnology- based systems. The results of a significant amount of testing and comparison are also described. A comparison is made between SnO2, ZnO, and TiO2 single-crystal nanowires and SnO2 polycrystalline nanofibers for gas sensing. The TECsynthesized single-crystal nanowires offer uniform crystal surfaces, resistance to sintering, and their synthesis may be done apart from the substrate. The TECproduced nanowire response is very low, even at the operating temperature of 200 C. In contrast, the electrospun polycrystalline nanofiber response is high, suggesting that junction potentials are superior to a continuous surface depletion layer as a transduction mechanism for chemisorption. Using a catalyst deposited upon the surface in the form of nanoparticles yields dramatic gains in sensitivity for both nanostructured, one-dimensional forms. For the nanowire materials, the response magnitude and response rate uniformly increase with increasing operating temperature. Such changes are interpreted in terms of accelerated surface diffusional processes, yielding greater access to chemisorbed oxygen species and faster dissociative chemisorption, respectively. Regardless of operating temperature, sensitivity of the nanofibers is a factor of 10 to 100 greater than that of nanowires with the same catalyst for the same test condition. In summary, nanostructure appears critical to governing the reactivity, as measured by electrical resistance of these SnO2 nanomaterials towards reducing gases. With regard to the sensitivity of the different nascent nanostructures, the electrospun nanofibers appear preferable

Hunter, Gary W.↗
DOE OSTI2022

Effects of processing temperature on the corrosion and tribocorrosion resistance of perhydropolysilazane-derived coatings on AISI 304 steel

Ensuring a highly corrosion and erosion resistant surface is critical to the reliability and structural integrity of steel canisters for long-term nuclear waste storage in corrosive environments. In this work, perhydropolysilazane (PHPS)-derived coating has been successfully applied to enhance the pitting and tribocorrosion resistance of 304 stainless steels in 0.6 M NaCl solution. Two types of coatings were synthesized on the stainless steel substrate by crosslinking PHPS at room temperature or 600 °C, resulting in different mechanical and corrosion performance. Further, Raman spectra revealed that Si-O bonds were generated in the coating crosslinked at room temperature after corrosion, while absent in that pyrolyzed at 600 °C. In tribocorrosion tests, both coatings were protective to the steel substrate, with the protective effect being more pronounced in the 600 °C pyrolyzed coating. Overall, the PHPS-derived coating synthesized at 600 °C exhibited better protection for steel in wear and corrosion coexisting environments than those synthesized at room temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2021

System and method for treating the surface of solid electrolytes

Disclosed are electrochemical devices, such as lithium battery electrodes, lithium ion conducting solid state electrolytes, and solid-state lithium metal batteries including these electrodes and solid state electrolytes. In one embodiment, a method for forming an electrochemical device is disclosed in which a precursor electrolyte is heated to remove at least a portion of a resistive surface region of the precursor electrolyte.

Sakamoto, Junki↗
DOE OSTI2020

Nb 3 Sn multicell cavity coating system at Jefferson Lab

Superconducting radio frequency niobium cavities are the building blocks of modern accelerators for scientific applications. Lower surface resistance, higher fields, and high operating temperatures advance the reach of the future accelerators for scientific discovery as well as potentially enabling cost-effective industrial solutions. We describe the design and performance of an Nb 3 Sn coating system that converts the inner surface of niobium cavities to an Nb 3 Sn film. The niobium surface, heated by radiation from the niobium retort, is exposed to Sn and SnCl 2 vapor during the heat cycle, which results in about 2 μm Nb 3 Sn film on the niobium surface. Film composition and structure as well as radio frequency properties with 1-cell R&D cavities and 5-cell practical accelerator cavities are presented.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Role of Surface Termination in the Metal–Insulator Transition of V 2 O 3 (0001) Ultrathin Films

Surface termination is known to play an important role in determining the physical properties of materials. It is crucial to know how surface termination affects the metal–insulator transition (MIT) of V 2 O 3 films for both fundamental understanding and its applications. By changing growth parameters, we achieved a variety of surface terminations in V 2 O 3 films that are characterized by low-energy electron diffraction (LEED) and photoemission spectroscopy techniques. Depending upon the terminations, our results show that MIT can be partially or fully suppressed near the surface region due to the different fillings of the electrons at the surface and subsurface layers and the change of screening length compared to the bulk. Across MIT, a strong redistribution of spectral weight and its transfer from a high-to-low-binding energy regime is observed in a wide energy scale. Our results show that the total spectral weight in the low-energy regime is not conserved across MIT, indicating a breakdown of the “sum rules of spectral weight”, signature of a strongly correlated system. Such a change in spectral weight is possibly linked to the change in hybridization, lattice volume (i.e., effective carrier density), and the spin degree of freedom in the system that occurs across MIT. We find that MIT in this system is strongly correlation-driven, where the electron–electron interactions play a pivotal role. Furthermore, our results provide better insight into the understanding of the electronic structure of strongly correlated systems and highlight the importance of accounting for surface effects during interpretation of the physical property data mainly using surface-sensitive probes, such as surface resistivity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Enable High-Energy LiNi0.5Co0.2Mn0.3O2 by Ultra-Thin Coating through Wet Impregnation

A high cut-off voltage is required for nickel-rich layered oxide LiNixCoyMnzO2 (NCM) to meet the high energy density requirement of lithium-ion batteries in electric vehicles. However, such a high voltage application leads to an unstable interface between NCM and liquid electrolytes. To stabilize the interface, the facile wet impregnation method has been developed to apply an ultra-thin Al2O3 coating layer on the NCM particles. This coating layer was found to have a strong interaction with the NCM and resulted in Al-doped NCM at the surface structure of NCM. The change of surface structure can not only reduce the surface resistance of lithium diffusion of LiNi0.5Co0.2Mn0.3O2 (NCM523), but also stabilize the solid electrolyte interface between NCM523 and the electrolyte with the cut-off voltage of 4.5 V vs. Li/Li+. Compared to other coating methods, wet impregnation coating can provide an ultra-thin and uniform coating with surface doping on NCM particles. Furthermore, this scalable coating method can be applied to various electrode materials without adding much additional cost.

25 ENERGY STORAGE↗
NASA NTRS1999

Copper-Based OHMIC Contracts for the Si/SiGe Heterojunction Bipolar Transistor Structure

Silicon based heterojunction bipolar transistors (HBT) with SiGe base are potentially important devices for high-speed and high-frequency microelectronics. These devices are particularly attractive as they can be fabricated using standard Si processing technology. However, in order to realize the full potential of devices fabricated in this material system, it is essential to be able to form low resistance ohmic contacts using low thermal budget process steps and have full compatibility with VLSI/ULSI processing. Therefore, a study was conducted in order to better understand the contact formation and to develop optimized low resistance contacts to layers with doping densities corresponding to the p-type SiGe base and n-type Si emitter regions of the HBTS. These as-grown doped layers were implanted with BF(sub 2) up to 1 X 10(exp 16)/CM(exp 2) and As up to 5 x 10(exp 15)/CM2, both at 30 keV for the p-type SiGe base and n-type Si emitter layers, respectively, in order to produce a low sheet resistance surface layer. Standard transfer length method (TLM) contact pads on both p and n type layers were deposited using an e-beam evaporated trilayer structure of Ti/CufTi/Al (25)A/1500A/250A/1000A). The TLM pads were delineated by a photoresist lift-off procedure. These contacts in the as-deposited state were ohmic, with specific contact resistances for the highest implant doses of the order of 10(exp -7) ohm-CM2 and lower.

Das, Kalyan↗
NASA NTRS2000

Reflective Silvered Polyimide Films Via In Situ Thermal Reduction Silver (I) Complexes

Self-metallizing. flexible polyimide films with highly reflective surfaces are prepared by an in situ self-metallization procedure involving thermally initiated reduction of polymer-soluble silver(I) complexes. Polyamic acid solutions are doped with silver(I) acetate and solubilizing agents. Thermally curing the silver(I) doped resins leads to flexible. metallized films which have reflectivities as high as 100%. abrasion-resistant surfaces. thermal stability and, in some cases, electrical conductivity, rendering them useful for space applications.

Southward, Robin E.↗
NASA NTRS1995

Development of LaRC (TM): IA thermoplastic polyimide coated aerospace wiring

NASA Langley has invented LaRC(exp TM) IA and IAX which are thermoplastic polyimides with good melting, thermal and chemical resistance properties. It was the objective of this contract to prepare and extrude LaRC (exp TM) polyimide onto aircraft wire and evaluate the polymers performance in this critical application. Based on rheology and chemical resistance studies at Imitec, LaRC (exp TM) IAX melts readily in an extruder, facilitating the manufacture of thin wall coatings. The polyimide does not corode the extruder, develop gel particles nor advance in viscosity. The insulated wire was tested according to MiL-W-22759E test specifications. The resulting wire coated with LaRC (exp TM) IAX displayed exceptional properties: surface resistance, non blocking, non burning, hot fluid resistance, impulse dielectric, insulation resistance, low temperature flexibility, thermal aging, wire weight, dimensions, negligible high temperature shrinkage and stripability. The light weight and other properties merit its application in satellites, missiles and aircraft applications. The extruded IAX results in a polyimide aircraft insulation without seams, outstanding moisture resistance, continuous lengths and abrasion resistance.

Keating, Jack↗
DOE OSTI2021

Properties of Nb3Sn films fabricated by magnetron sputtering from a single target

Superconducting Nb3Sn films were fabricated on sapphire and fine grain Nb substrates by magnetron sputtering from a single stoichiometric Nb3Sn target. The structural, morphological and superconducting properties of the films annealed for 24 h at temperatures of 800-1000 {\deg}C were investigated. The effect of the annealing time at 1000 {\deg}C was examined for 1, 12, and 24 h. The film properties were characterized by X-ray diffraction, scanning electron microscopy, atomic force microscopy, energy dispersive X-ray spectroscopy, and Raman spectroscopy. The DC superconducting properties of the films were characterized by a four-point probe measurement down to cryogenic temperatures. The RF surface resistance of films was measured over a temperature range of 6-23 K using a 7.4 GHz sapphire-loaded Nb cavity. As-deposited Nb3Sn films on sapphire had a superconducting critical temperature of 17.21 K, which improved to 17.83 K when the film was annealed at 800 {\deg}C for 24 h. For the films annealed at 1000 {\deg}C, the surface Sn content was reduced to ~11.3 % for an annealing time of 12 h and to ~4.1 % for an annealing time of 24 h. The Raman spectra of the films confirmed the microstructural evolution after annealing. The RF superconducting critical temperature of the as-deposited Nb3Sn films on Nb was 16.02 K, which increased to 17.44 K when the film was annealed at 800 {\deg}C for 24 h.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Topographic Evolution of Heat-Treated Nb Upon Electropolishing for SRF Applications

Surface finish plays an essential role in the performance of superconducting radio frequency cavities. Several surface treatments have been developed to reduce surface resistance at a moderate accelerating gradient. We investigated the effects of sequential electropolishing on samples vacuum heat-treated at 300 and 600 °C and N-doped Nb samples using atomic force microscopy. The N-doping process precipitates niobium nitrides within grains and, most notably, continuously and deeply along some grain boundaries. Upon electropolishing, the nitrides are preferentially removed leaving behind a topographically imperfect surface marked by relatively deep holes and grooves with low radius of curvature edges. The progression of magnetic field enhancement and superheating field suppression factors upon electropolishing were investigated using atomic force micrographs. While minor changes in magnetic field enhancement and superheating field suppression factors are observed for the 300 and 600 °C heat-treated Nb, substantial improvements are observed for N-doped Nb. In this system, the most severe topographic defects are the grain boundary grooves which substantially suppress the superheating field. We find that the severity of topographic defects is related to the N-doping process.

Lechner, Eric↗
DOE OSTI2022

Electrical edge effect induced photocurrent overestimation in low-light organic photovoltaics

In many literatures, the short-circuit current (J SC ) of indoor organic photovoltaics is overestimated, leading to severely wrong device performance evaluation and analysis. In this work, based on the equivalent circuit model, we demonstrate that electrical edge effect is sensitive to both transverse surface resistance and light intensity. At low light intensity, the electrical edge effect could lead to J SC being significantly overestimated, i.e., by 100% and even more. We show that for a PM6:Y6 device capped with a MoOX layer, when measured under 0.01 sun, the usually overlooked interface doping mechanism would lead to J SC and PCE overestimation by 51% and 15%, respectively. Besides, we show that the magnitude of J SC overestimation drastically increases with high photoactive-layer surface roughness. This work emphasized the significant electrical edge effect on J SC evaluations for low-light solar cells and is conducive to understanding the intrinsic mechanism of edge effect, promoting a healthier development of organic photovoltaics.

14 SOLAR ENERGY↗
NASA NTRS1990

Airborne flux measurements and budget estimates of trace species over the Amazon Basin during the GTE/ABLE 2B expedition

In situ airborne measurements of turbulent heat, moisture, momentum, ozone, and carbon monoxide fluxes in a convective boundary layer were obtained over a tropical rain forest between 1100 and 1630 LT on May 4, 1987. The aircraft flight path was chosen so as to fly over the tower site at the Ducke Forest Reserve near Manaus, Amazonas, Brazil. Both turbulence statistics and mean quantities were used to study the budgets of heat, water vapor, ozone, and carbon monoxide. The ozone budget study shows an accumulation rate in the boundary layer of 0.3 + or - 0.2 ppbv/h. The surface resistance to ozone during this flight was determined to be 0.06 + or - 0.03 s/cm, while the aerodynamic resistance was 0.14-0.17 s/cm. Results from the CO budget analysis show a midday accumulation rate of 0.6 + or - 0.3 ppbv/h in the Amazonian boundary layer. The evidence suggests production of CO in the PBL. A source of CO may exist below the lowest flight level (about 150 m), although it was not possible to determine what part of the flux at flight level was due to chemical production and what part may be due to surface emission.

Ritter, John A.↗
DOE OSTI2025

First elliptical cavity fabricated with metallographic polishing

The development of an easy and inexpensive Nb sheet preparation process, based on metallographic polishing, has been presented earlier [1, 2]. The aim is to remove the damage layer caused by the rolling process on the sheet in order to reduce the length of surface treatment on completed cavities. The process has been applied on a QPR sample and tested in RF, without any surface chemistry. Its surface resistance is about 4 times lower than the EP baseline at 414 MHz, 2 K [3]. The first elliptical cavity based on this principle has been produced at KEK, starting with large polished sheets developed in collaboration between IJCLAB, and the company LAMPLAN. We present its 1st RF test at KEK, with a HF rinsing and a recrystallization treatment at 600C for 10h, without any chemical etching at first. References: *1: C. Antoine and R. Crooks, “Reducing Electropolishing Time with Chemical-Mechanical Polishing”, SRF2009. *2: O. Hryhorenko, et al., "An innovative approach of surface polishing for SRF cavity applications". Journal of Manufacturing and Materials Processing, 2023. 7(2): p. 62. *3: O. Hryhorenko, et al., "Recent advances in metallographic polishing for SRF application", SRF2023.

Dohmae, Takeshi [High Energy Accelerator Research ↗
NASA NTRS2017

Active Electrostatic flight for airless bodies

The environment near the surface of asteroids, comets, and the Moon is electrically charged due to the Sun’s photoelectric bombardment and lofting dust, which follows the Sun illumination as the body spins. Charged dust is ever present, in the form of dusty plasma, even at high altitudes, following the solar illumination. If a body with high surface resistivity is exposed to the solar wind and solar radiation, sunexposed areas and shadowed areas become differentially charged. The E-Glider (Electrostatic Glider) is an enabling capability for operation at airless bodies, a solution applicable to many types of in-situ missions, which leverages the natural environment. This platform directly addresses the "All Access Mobility" Challenge, one of the NASA’s Space Technology Grand Challenges. Exploration of comets, asteroids, moons and planetary bodies is limited by mobility on those bodies. The lack of an atmosphere, the low gravity levels, and the unknown surface soil properties pose a very difficult challenge for all forms of know locomotion at airless bodies. This EGlider levitates by extending thin, charged, appendages, which are also articulated to direct the levitation force in the most convenient direction for propulsion and maneuvering. The charging is maintained through continuous charge emission. It lands, wherever it is most convenient, by retracting the appendages or by firing a cold-gas thruster, or by deploying an anchor. Preliminary calculations indicate that a 1 kg mass can be electrostatically levitated in a microgravity field with a 2 m diameter electrostatically inflated ribbon structure at 19kV, hence the need for a “balloon-like” system. The wings could be made of very thin Au-coated Mylar film, which are electrostatically inflated, and would provide the lift due to electrostatic repulsion with the naturally charged asteroid surface. Since the E-glider would follow the Sun’s illumination, the solar panels on the vehicle would constantly charge a battery. Further articulation at the root of the lateral strands or inflated membrane wings, would generate a component of lift depending on the articulation angle, hence a selective maneuvering capability which, to all effects, would lead to electrostatic (rather than aerodynamic) flight.

Schaub, Hanspeter↗