Search NASA⌕ Search

SEARCH · Search NASA

Results for “scanning electron microscopy (SEM)”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Assessment of Dynamic Fracture in Ultra-High Performance Concrete Using Synchrotron X-ray Source

Ultra-high-performance concretes (UHPCs) retain higher ultimate (compressive) strengths and greater durability relative to traditional concrete materials. As a result, they are enabling construction materials for blast resistant structures, where a higher capacity for energy absorption is required. In past investigations, the strength of UHPCs was shown to retain a dependency on strain rate. Still, the failure mechanisms which govern this rate dependency have yet to be completely elucidated. In the current study, the dynamic fracture behavior of Cor-tuf UHPC was assessed, in-situ, using a Synchrotron X-ray source in phase contrast imaging (PCI) mode. Prior to testing, the material’s morphology was characterized using X-ray computed tomography (CT) and scanning electron microscopy (SEM). A polychromatic pulsed X-ray source, high-speed camera and Kolsky bar apparatus were used in tandem, to observe the transient failure modes. A pin was placed at the end of the incident bar to control the location of damage initiation, and tests were performed at a constant velocity of ~6 m/s. These test conditions were observed to yield cracks with median and/or cone like geometries. Despite the variation in the crack paths, a significant difference in peak load was not observed. The failure mode was also observed to depend on the microstructure of the concrete samples.

Kolsky bar↗
DOE OSTI2020

Computational Methods to Accelerate Development of Corrosion Resistant Coatings for Industrial Gas Turbines

Oxidation resistant overlay coatings protect the underlying superalloy component in industrial gas turbines from oxidation attack. Rate of depletion of the Al-rich β-phase in the bond coat governs the lifetime of these coatings. The applicability of a computational method in accelerating the development of corrosion resistant coatings and significantly reducing the extensive experimental effort to predict coating lifetimes and microstructural changes in three-coated Ni-based superalloys for real operational durations (20–40 kh) was undertaken in the present study. Scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), and electron microprobe analysis (EPMA) were employed to characterize MCrAlY-coated superalloy substrates (1483, 247 and X4) after exposure at 900 °C in air + 10% H 2 O for up to 20,000 h. The model predicted the longest coating lifetime for the coating on X4 substrate. Precipitation of γ' in the coatings was correctly predicted for all three coating systems. Additionally, the model was able to predict the formation of topologically close packed (TCP)-phases in the investigated coating systems.

Pillai, Rishi R.↗
DOE OSTI2024

Nanocomposite Materials for Radionuclide Sequestration from Groundwater Environments

The half-lives of radionuclides range from fractions of a second to billions of years. Since no practical method of altering radioactive decay exists, and since exposure to either the energy emitted from radioactive decay or chemical properties of radionuclides poses dire health risks, radioactive materials must be segregated and controlled. The capture, treatment, and disposition of radioactive materials remain an extraordinary challenge. In here, we focus our attention on the synthesis and characterization of a unique class of nanocomposite materials that have potential for removal of radionuclide contamination. Specifically, we report a simple approach to decorate the surface of iron-based (Fe/FexOy) material with various nano-catalysts. Specifically, copper (Cu), tin (Sn), and silver (Ag) nanoparticles were prepared through two different reduction approaches, namely, citrate and cetyltrimethylammonium bromide (CTAB) methods, on the iron-based material surface. All samples were characterized by a variety of analytical tools, which included scanning electron microscopy (SEM), electron-dispersive X-ray microanalysis (EDS), and EDS mapping to elucidate materials’ morphology as well as nano-catalysts’ loading and location on the iron-based structures.

Hunyadi Murph, Simona E.↗
DOE OSTI2024

Smart manufacturing approach to manufacture bulk nanocrystalline aluminum for lightweight applications

In this research, a smart manufacturing approach was used to enhance the mechanical properties of aluminum (Al) for lightweight applications. The smart manufacturing involved cryomilling of Al powders with and without 5 wt.% magnesium (Mg) powders for varying durations followed by a high-pressure cold spray (HPCS) additive manufacturing process to prepare bulk components. The morphological changes, crystallite size, and composition of the cryomilled powders and cold sprayed (CS’ed) components were examined using scanning electron microscopy (SEM), x-ray diffraction (XRD), and transmission electron microscopy (TEM) techniques. The results showed that the crystallite size reduces with an increase in cryomilling time and the addition of Mg dopant. To test the mechanical properties of the bulk CS’ed components, microhardness tests were performed using a Vickers microhardness tester. Uniaxial tensile tests were also carried out to ascertain the material’s tensile properties. The mechanical testing results showed great improvement in the hardness and tensile strength of CS’ed Al–Mg samples as compared to pure Al samples. Subsequently, fractography analysis of the tensile failed samples was carried out to determine the nature of the failure. Here, the research article also discusses the inherent mechanisms for the improvement in mechanical properties of smart manufactured components as a result of Mg doping and cryomilling.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Microstructural evolution in a precipitate-hardened (Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 ) 94 Ti 2 Al 4 multi-principal element alloy during high-pressure torsion

Multi-principal element alloys demonstrate high strength, thermal stability, and irradiation resistance, making them excellent candidate materials for applications in nuclear reactors and other harsh environments. Some studies have examined the use of high-pressure torsion to strengthen MPEAs through grain size reduction and strain hardening. However, no studies have investigated the effect of HPT on secondary phases (precipitates) within an MPEA. Two alloys, (Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 ) 94 Ti 2 Al 4 containing Ni(Ti, Al) B2 phase, and CrFe σ phase, and single-phase Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 , were fabricated by casting and heat treatment. Both alloys were then processed with HPT to study microstructural evolution. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to characterize the alloys before and after HPT processing. HPT processing produced a nanocrystalline structure in both alloys, but (Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 ) 94 Ti 2 Al 4 exhibited a significantly smaller grain size and higher dislocation density than Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 , with corresponding higher hardness. Before HPT, the (Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 ) 94 Ti 2 Al 4 alloy consisted of large grain (~ 400 μm) and precipitates, including B2 of ~ 38 μm average size, B2 of ~ 0.7 μm average size, and small amounts of σ of ~ 1.5 μm average size. After HPT, the larger B2 precipitates were decreased in size and volume fraction, while the smaller B2 precipitates were completely dissolved; the σ precipitates appeared unaffected by HPT, likely due to their much higher hardness. Finally, observation of the B2 precipitate distribution along radial distance indicates that the strain caused the precipitates to fracture at intermediate strain (γ = 125) and dissolve at high strain (γ = 280).

36 MATERIALS SCIENCE↗
DOE OSTI2025

Multiscale Characterization of Additive Manufacturing Components with Computed Tomography, 3D X-ray Microscopy, and Deep Learning

Additive manufacturing (AM) facilitates the creation of complex-geometry parts, driving advancements in lightweight aerospace components, high-efficiency engine cooling channels, and customized medical implants. However, ensuring the quality and reliability of AM parts remains challenging due to internal defects, surface irregularities, porosity, and residual trapped powder, which are often inaccessible to traditional inspection methods. Recent developments in X-ray computed tomography (XCT) and 3D X-ray microscopy (XRM), particularly systems equipped with resolution-at-a-distance (RaaD™) capabilities, enable high-resolution, non-destructive evaluation of AM components across multiple scales, from sub-micrometer to macroscopic levels. This paper explores modern XCT and XRM techniques for multiscale characterization of AM parts, focusing on their ability to detect and analyze defects such as porosity, cracks, inclusions, and surface roughness, while offering insights into defect formation mechanisms, material properties, and process-induced variations. The integration of deep learning (DL) frameworks, including Simurgh, DeepRecon, and DeepScout, enhances XCT/XRM workflows by reducing scan times, improving resolution recovery, and enabling accurate defect detection even with limited projection data. These DL-based methods overcome limitations of traditional reconstruction techniques, enabling faster, more reliable characterization of dense materials like Inconel 718 and novel alloys such as AlCe. Applications include process parameter optimization, high-throughput quality control, and multistage AM process evaluation, with DL-enhanced workflows accelerating analysis times from weeks to days. Correlative imaging approaches further validate XCT and XRM data against scanning electron microscopy (SEM) images of physically sectioned samples, confirming the accuracy of DL-based reconstructions and enabling comprehensive defect analysis. While challenges remain in generalizing DL models to diverse materials and imaging conditions, improvements in resolution, noise reduction, and defect detection highlight the transformative potential of these methods. This multiscale and correlative approach enables precise identification and correlation of microstructural features with the overall performance of AM components. By integrating advanced XCT, XRM, and DL techniques, this paper demonstrates a significant leap forward in AM characterization, offering valuable insights into the relationships between processing parameters, microstructure, and part performance, and driving innovations that enhance the quality and reliability of AM products for demanding industrial applications.

Additive manufacturing↗
DOE OSTI2022

Chemical and structural characterization of particulate fallout isolated from air-filters

We report particulate nuclear fallout is the radioactive byproduct of a nuclear event formed by the mixture of proximate environmental materials with vaporized bomb debris. The fallout debris can be transported into the atmosphere during cloud rise, raining out locally and dispersing globally constituting a radiation hazard and contributing to the distribution of anthropogenic radionuclides in the environment. Questions remain on how entrainment of environmental material in the fireball affects fallout formation processes and radionuclide incorporation and distribution during cooling. To inform the characterization of fallout including the development of fallout size distributions and how radionuclides are incorporated into fallout debris where entrainment plays a role, we analyzed an archived historic US air-filter collected by aircraft in the aftermath of ground interacting nuclear tests. Particulate fallout collected on the filter was isolated and analyzed using scanning electron microscopy (SEM), transmission electron microscopy (TEM) and NanoSIMS (Secondary Ion Mass Spectrometry) to determine chemistry, structure, morphology, and size of the particles. Results demonstrate that the particles isolated from the filter have spherical shape, display complex internal structures, and are mainly composed of Fe and Si oxides. In these spherical particles, Pu is preferentially associated with Fe-rich composition. The characterization of fallout particulate samples can provide information on nucleation and particle growth from the vapor phase to improve modeling and simulation of fallout hazards.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2026

Metal alloy microparticle tagging of UO 2 fuel pellets for nuclear forensics

A tagging strategy for UO 2 fuel pellets will be discussed which involves the creation of alloyed metal microparticles that can be tuned to create a unique identification (“barcode”) indicating provenance of the pellets. These specialized markers would contain high temperature resistant materials, such as Ti, Mo, and Cr, in small quantities such that they do not interfere with the performance of the pellets but are recoverable by standard analytical techniques. The Amazemet rePowder ultrasonic atomization system was used to manufacture the microparticles, and sample pellets were fabricated and sintered containing these dopants. Various techniques, such as Scanning Electron Microscopy (SEM) and Electron Probe Microanalysis (EPMA), were used to evaluate these sample pellets to determine if particles (and their alloy compositions) were recoverable. Details on how the particles were manufactured and characterized will be detailed, as well as results from their incorporation into test pellets. Next steps will involve the scale of this technique using more conventional mass production methods, as well as the implementation of other alloys.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Microstructural Analysis of Cadmium Whiskers on Long-Term-Used Hardware

A survey of cadmium plated field return hardware showed ubiquitous cadmium whisker growth. The most worn and debris-covered hardware showed the densest whisker growth. Whiskers were often found growing in agglomerates of nodules and whiskers. The hardware was rinsed with alcohol to transfer whiskers and debris from the hardware to a flat stub. Fifty whiskers were studied individually by scanning electron microscopy (SEM), including energy dispersive spectroscopy (EDS) and electron backscatter diffraction (EBSD). Most of the whiskers were single crystal, though three were found to contain grain boundaries at kinks. The whiskers ranged from 5 to 600 μm in length and 80 pct showed a $<\bar{1} 2 \bar{1} 0>$ type growth direction. This growth direction facilitates the development of low energy side faces of the whisker, (0001) and {1010}.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Minor Elements and Solidification Cracking During Laser Powder-Bed Fusion of a High $\gamma ^{\prime }$ CoNi-Base Superalloy

Here, the cracking behavior of a high γ' volume fraction CoNi-base superalloy fabricated via laser powder bed fusion (LPBF) is studied in relation to the content of carbon and boron. Severe cracking occurred with the increase in boron content from 0.08 to 0.16 at. pct (0.015 to 0.029 wt pct), while compositions with 0.1 to 0.36 at. pct C (0.02 to 0.076 wt pct) and 0.08 at. pct B exhibited minimal cracking. Assessment of cracks in the high-boron composition shows a variation in crack density with printing parameters, and alignment of the cracks with the build direction. Scanning electron microscopy (SEM) of the crack surfaces shows evidence of a solidification cracking mode. Differential thermal analysis (DTA) reveals a decreased incipient melting temperature for the high-boron composition, and atom probe tomography (APT) is used to measure the enrichment at grain boundaries, revealing distinct boron segregation. Scheil-Gulliver solidification simulations for the different C and B levels are consistent with the incipient melting behavior observed with DTA. Evaluation of the solidification cracking susceptibility from the simulations allow for comparison of the CoNi alloy behavior to Ni-base superalloys studied for LPBF fabrication and displays how such metrics may aid in the design of new precipitation-strengthened superalloys for additive manufacturing (AM).

36 MATERIALS SCIENCE↗
DOE OSTI2024

Characterization and Rationalization of Microstructural Evolution in GRCop-84 Processed by Laser-Powder Bed Fusion (L-PBF)

In this study, prismatic geometries of GRCop-84 [Cu-8Cr-4Nb (at. pct)] were built with laser-powder bed fusion (L-PBF) process. The samples were sectioned parallel or perpendicular to the build direction and characterized in the as-built and after post-processing with a hot-isostatically pressing (HIP) treatment. The microstructure and phase evolutions were evaluated with optical microscopy, scanning electron microscopy (SEM), electron backscattered diffraction (EBSD), and high-temperature X-ray diffraction (HTXRD) up to 1223 K. The samples in the as-built conditions exhibited predominantly columnar epitaxial and misoriented Cu-FCC grains. The microstructure evolutions are discussed based on locations within the overall build geometry, the dynamics of small melt pool shape and sectioning effects. The above grain structure did not change significantly during post-process HIP treatment. The stability of this FCC grain structure is attributed to the formation of primary stable Cr 2 Nb (Laves phase) during L-PBF, even before the emergence of FCC grains from liquid. The stability of Cr 2 Nb in both as-built and HIPed samples were evaluated using high-temperature X-ray diffraction measurements and compared with that of gas-atomized powder. The significance of these results is discussed with reference to aerospace applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Solid State Reduction Driven Synthesis of Mn Containing Multi-principal Component Alloys

In recent years, high entropy alloys (HEAs), also known as multi-principal component alloys (MPCAs) have emerged as a new and exciting class of materials. This paper reports on the solid state reduction synthesis of a series of CoFeNiMn-based MPCA compositions, starting from a mixture of the corresponding oxides. One of the aims of the study was to test whether the degree of reduction of MnO, a highly stable oxide, could be enhanced by tailoring the alloy composition. Specifically, the influence of Ni content was studied because Ni exhibits a significant negative enthalpy of mixing with Mn. High purity precursor powders of Co(OH) 2 , Fe 2 O 3 , MnO 2 , and NiO were milled and mixed using standard ceramic processing methods. Here, the nominal sample compositions (assuming complete oxide reduction) were (CoFeMn) x Ni (1-x) , for x = 0, 0.083, 0.166, and 0.25. The oxide samples were subjected to a series of isothermal reduction anneals in flowing 3 pct H 2 –Ar at 1100 °C. The resulting microstructures were characterized using scanning electron microscopy (SEM), X-ray energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD). The composition of the resulting MPCAs was determined quantitatively using wavelength dispersive spectroscopy (WDS) in the electron microprobe. The study revealed that for each of the initial oxide compositions studied, it was possible to achieve an MPCA with ~ 25 at. pct Mn. These results were found to be consistent with the predictions of a thermodynamic model whereby a negative enthalpy of mixing (ΔH mix ), combined with a contribution from configurational entropy, can offset a positive free energy of reduction (ΔG red ). The incorporation of vibrational entropy into first principles calculations was found to have a significant effect on the predicted crystal structure of the MPCAs.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Mechanical Performance and Mesostructure Analysis of Proton-Irradiated Fused Filament Fabrication Acrylonitrile Butadiene Styrene Material

The use of fused filament fabrication (FFF) acrylonitrile butadiene styrene (ABS) and other thermoplastics in radiation environments is beginning to be studied as possible replacements for traditionally manufactured parts and tools. Interlayer adhesion within the mesostructure has been shown in published literature to be an integral component in the strength of FFF ABS. Research of irradiated 3D printed polymers has primarily focused on the influence of gamma irradiation on the mechanical properties of FFF ABS samples, without evaluating its impact on the mesostructure of the samples. The purpose of this paper is to understand the mechanical damage caused by proton radiation on FFF ABS samples through the evaluation of the mesostructure of the ABS samples. To achieve this objective, proton radiation at 40 MeV was applied to FFF ABS samples at radiation doses up to 1.0 MGy at a dose rate of 1 MGy/hr. Following the irradiation, tensile testing was performed on the samples. Here, the fractured surfaces of the tested samples were subsequently observed using a scanning electron microscope. The mechanical test results show an increase in the ultimate tensile strength (UTS) and a decrease in the ductility of the irradiated samples. Statistical analysis on the results shows that there is a statistically significant difference in the UTS and the ductility of unirradiated and 1.0 MGy irradiated samples and between irradiated samples and 1.0 MGy samples. In addition, the percentage elongation at break has statistically significant differences in the means between irradiated samples and 1.0 MGy samples. The UTS has statistically significant differences in the means between 0.1 MGy and 1.0 MGy. The difference in the means between the unirradiated and the 1.0 MGy samples is the most significant for both the UTS and elongation at break. The scanning electron microscopy (SEM) results indicated that interlayer adhesion improved as a function of radiation dose corresponding to the increase in tensile strength. The SEM results also showed that crazing and plastic deformation were reduced; aligning with the loss in ductility observed in the tensile tests results. The proton radiation is causing these mechanical and physical changes through two mechanisms: (1) dose rate effects on ionizing radiation-induced oxidative degradation; and (2) radiation heating effects of high energy (>1 MeV) charged particles.

electron microscopy↗
DOE OSTI2023

Enhancement in Mechanical Properties of Bulk Nanocrystalline Aluminum by Grain Boundary Strengthening Mechanism

In the present work, commercially pure aluminum (Al) powders were milled at cryogenic temperatures (a) without magnesium (Mg) and (b) with 5 wt.% Mg powders for different durations. The cryomilled powders were analyzed using scanning electron microscopy (SEM), transmission electron microscopy (TEM), and x-ray diffraction (XRD) to determine the changes in particle morphology, elemental composition, and crystallite size. The results showed a reduction in crystallite size with the increase in cryomilling duration. Thereafter, the spark plasma sintering (SPS) process was carried out to manufacture bulk samples. The mechanical properties of the bulk SPS samples were assessed by conducting microhardness, tensile, and fatigue tests. The Vickers microhardness tests showed improved hardness for the Al-Mg bulk samples as compared to pure Al. The Al-Mg samples also showed an increase in tensile strength with increasing cryomilling time. Fatigue test results showed an improvement in Al-Mg components' high-cycle fatigue response. Furthermore, the mechanism for the enhancement in mechanical properties as a result of crystallite size reduction and grain boundary strengthening by the addition of Mg dopant is also discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Investigation of Mechanical Properties of Parts Fabricated with Gas- and Water-Atomized 304L Stainless Steel Powder in the Laser Powder Bed Fusion Process

In this report the use of gas-atomized powder as the feedstock material for the Laser Powder Bed Fusion (L-PBF) process is common in the Additive Manufacturing (AM) community. Although gas-atomization produces powder with high sphericity, its relatively expensive production cost is a downside for application in AM processes. Water atomization of powder may overcome this limitation due to its low cost relative to the gas-atomization process. In this work, gas- and water-atomized 304L stainless steel powders were morphologically characterized through Scanning Electron Microscopy (SEM). The water-atomized powder had a wider particle size distribution and exhibited less sphericity. Measuring powder flowability using the Revolution Powder Analyzer (RPA) indicated that the water-atomized powder had less flowablility than the gas-atomized powder. Through examining the mechanical properties of L-PBF fabricated parts using tensile tests, the gas-atomized powder had significantly higher yield tensile strength and elongation than the water-atomized powder, however, their ultimate tensile strengths were not significantly different.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Quantifying the Relationship Between Microstructure and Performance in Gadolinium-Doped Ceria Infiltrated Ni/YSZ Symmetric Cells

Infiltration of mixed ionic/electronic conducting (MIEC) nanocatalysts into the anodes of solid oxide fuel cells (SOFCs) allow the hydrogen oxidation reaction (HOR) to occur at double-phase boundaries (DPBs), rather than being confined only to the triple phase boundaries (TPBs). In this research, we use a combination of cross-sectional scanning electron microscopy (SEM), three-dimensional (3-D) reconstruction, and electrochemical methods to characterize both baseline and gadolinium-doped ceria (GDC)-infiltrated symmetric cells, with the goal of establishing a comparison between the density of electrochemically active sites in uninfiltrated and GDC-infiltrated cells. Here, electrochemical impedance spectroscopy (EIS) and distribution of relaxation times (DRT) analysis showed GDC infiltration decreased the overall polarization of the anode by a factor of 8.78 X, and decreased the resistance associated with the reactions at the TPBs/DPBs by a factor of over 21 X. By quantifying expected GDC deposition morphology in the Ni/YSZ anode it is estimated that reactions occur in the baseline cell up to 84 nm from the active TPB lines.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Nitrogen-doped char as a catalyst for wet oxidation of phenol-contaminated water

Catalytic wet oxidation (CWO) of aqueous effluents rich in organic compounds is a very promising technology for the treatment of liquid wastes from biomass conversion processes. CWO reactions occur through the formation of free radical species, produced in the presence of an oxidant, which act on organic contaminates in the effluent. Although the reaction is well known, there exists a lack of affordable catalysts to conduct this process at the lower temperatures and pressures in novel bioenergy processes. Here, this study assessed the catalytic effect of nitrogen-doped chars as such an option. Phenol in aqueous solution was used as a model waste effluent. Treatment was conducted at moderate temperatures (190 to 260 °C), oxygen partial pressure of 1 MPa, and reaction times of 15, 30, and 45 min in stainless steel and glass-lined tube reactors. High pressure liquid chromatography (HPLC) analyses of the products quantified phenol and by-product concentrations used in the calculation of reaction activation energy. The char catalyst was studied by X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), and scanning electron microscopy (SEM) in order to gain insight into its structure and surface composition. The results indicate that nitrogen-doped char catalysts accelerate the oxidation of phenol by decreasing its reaction activation energy from 82.2 kJ/mol (non-catalyzed) to 40.4 kJ/mol (catalyzed). An analysis from first principles using density functional theory (DFT) was conducted to ascertain which N functional group has the most significant impact on free radical formation in the presence of oxygen. Among all the N functional groups studied, the dipyridinic functional groups showed the most promising characteristics to facilitate the formation of hydroxyl free radicals.

Advanced Oxidation Processes for Organic Pollutant↗
DOE OSTI2024

Location-Specific Microstructure Characterization Within AM Bench 2022 Nickel Alloy 718 3D Builds

Abstract The Additive Manufacturing Benchmark Test Series (AM Bench) is a broad effort to produce rigorous measurement datasets for validating AM computer simulations across the range of processing, structure, and properties, for many additive manufacturing (AM) build methods and material classes. Here, the microstructures of nickel alloy 718 AM Bench 2022 test artifacts produced using laser-based powder bed fusion (PBF-LB), in both as-built and fully heat-treated conditions, are examined. Cross sections are primarily characterized using large area scanning electron microscopy (SEM) electron backscatter diffraction (EBSD) and example analyses of the crystallographic textures are described. These data are part of a large set of in situ and ex situ measurements from both three-dimensional builds and laser tracks on bare plates. All the measurement data are available online with download links at www.nist.gov/ambench .

Levine, L. E. (ORCID:0000000334484229)↗