Search NASA⌕ Search

SEARCH · Search NASA

Results for “secondary”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS2015

Secondary Instability of Stationary Crossflow Vortices in Mach 6 Boundary Layer Over a Circular Cone

Hypersonic boundary layer flows over a circular cone at moderate incidence can support strong crossflow instability. Due to more efficient excitation of stationary crossflow vortices by surface roughness, such boundary layer flows may transition to turbulence via rapid amplification of the high-frequency secondary instabilities of finite amplitude stationary crossflow vortices. The amplification characteristics of these secondary instabilities are investigated for crossflow vortices generated by an azimuthally periodic array of roughness elements over a 7-degree half-angle circular cone in a Mach 6 free stream. Depending on the local amplitude of the stationary crossflow mode, the most unstable secondary disturbances either originate from the second (i.e., Mack) mode instabilities of the unperturbed boundary layer or correspond to genuine secondary instabilities that reduce to stable disturbances at sufficiently small amplitudes of the stationary crossflow vortex. The predicted frequencies of dominant secondary disturbances are similar to those measured during wind tunnel experiments at Purdue University and the Technical University of Braunschweig, Germany.

Boundary layer flow↗
NASA NTRS2016

Stationary Crossflow Breakdown due to Mixed Mode Spectra of Secondary Instabilities

Numerical simulations are used to study laminar breakdown characteristics associated with stationary crossflow instability in the boundary-layer flow over a subsonic swept-wing configuration. Previous work involving the linear and nonlinear development of individual, fundamental modes of secondary instability waves is extended by considering the role of more complex, yet controlled, spectra of the secondary instability modes. Direct numerical simulations target a mixed mode transition scenario involving the simultaneous presence of Y and Z modes of secondary instability. For the initial amplitudes investigated in this paper, the Y modes are found to play an insignificant role during the onset of transition, in spite of achieving rather large, O(5%), amplitudes of RMS velocity fluctuation prior to transition. Analysis of the numerical simulations shows that this rather surprising finding can be attributed to the fact that the Y modes are concentrated near the top of the crossflow vortex and exert relatively small influence on the Z modes that reside closer to the surface and can lead to transition via nonlinear spreading that does not involve interactions with the Y mode. Finally, secondary instability calculations reveal that subharmonic modes of secondary instability have substantially lower growth rates than those of the fundamental modes, and hence, are less likely to play an important role during the breakdown process involving complex initial spectra.

Li, Fei↗
NASA NTRS2023

Rapid transition from primary to secondary crust building on the Moon explained by mantle overturn

Geochronology indicates a rapid transition (tens of Myrs) from primary to secondary crust building on the Moon. The processes responsible for initiating secondary magmatism, however, remain in debate. Here we test the hypothesis that the earliest secondary crust (Mg-suite) formed as a direct consequence of density-driven mantle overturn, and advance 3D mantle convection models to quantify the resulting extent of lower mantle melting. Our modeling demonstrates that overturn of thin ilmenite-bearing cumulates ≤ 100 km triggers a rapid and short-lived episode of lower mantle melting which explains the key volume, geochronological, and spatial characteristics of early secondary crust building without contributions from other energy sources, namely KREEP (potassium, rare earth elements, phosphorus, radiogenic U, Th). Observations of globally distributed Mg-suite eliminate degree-1 overturn scenarios. We propose that gravitational instabilities in magma ocean cumulate piles are major driving forces for the onset of mantle convection and secondary crust building on differentiated bodies.

Moon↗
DOE OSTI2022

Time-resolved chemical studies via time-of-flight secondary ion mass spectrometry

A method of performing time-of-flight secondary ion mass spectrometry on a sample includes the step of directing a beam of primary ions to the sample, and stimulating the migration of ions within the sample while the beam of primary ions is directed at the sample. The stimulation of the ions is cycled between a stimulation state and a lower stimulation state. Secondary ions emitted from the sample by the beam of primary ions are collected in a time-of-flight mass spectrometer. Time-of-flight secondary ion mass spectrometry is then performed on the secondary ions. A system for performing time-of-flight secondary ion mass spectrometry on a sample is also disclosed.

Ievlev, Anton V.↗
DOE OSTI2025

New approaches to secondary metabolite discovery from anaerobic gut microbes

The animal gut microbiome is a complex system of diverse, predominantly anaerobic microbiota with secondary metabolite potential. These metabolites likely play roles in shaping microbial community membership and influencing animal host health. As such, novel secondary metabolites from gut microbes hold significant biotechnological and therapeutic interest. Despite their potential, gut microbes are largely untapped for secondary metabolites, with gut fungi and obligate anaerobes being particularly under-explored. To advance understanding of these metabolites, culture-based and (meta)genome-based approaches are essential. Culture-based approaches enable isolation, cultivation, and direct study of gut microbes, and (meta)genome-based approaches utilize in silico tools to mine biosynthetic gene clusters (BGCs) from microbes that have not yet been successfully cultured. In this mini-review, we highlight recent innovations in this area, including anaerobic biofoundries like ExFAB, the NSF BioFoundry for Extreme & Exceptional Fungi, Archaea, and Bacteria. These facilities enable high-throughput workflows to study oxygen-sensitive microbes and biosynthetic machinery. Such recent advances promise to improve our understanding of the gut microbiome and its secondary metabolism.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

Metal (Fe, Cu, and As) transformation and association within secondary minerals in neutralized acid mine drainage characterized using X-ray absorption spectroscopy

The formation and transformation of secondary minerals in areas affected by neutralized acid mine drainage (AMD) determine the behavior of toxic elements. To better understand the binding form of toxic elements in the secondary minerals, we focused on the distribution of secondary precipitates and heavy metals in neutralized AMD near a typical Cu-polymetallic deposit located in central Tibet. Compared to background values, the average heavy metal (As, Cu, Co, Cu, Mo, Pb, and Zn) content is higher in sediments close to the neutralized AMD drain. X-ray absorption spectroscopy (XAS) characterization shows the Fe in the suspended particulate matter (SPM) first aggregate as small Fe(III) octahedra clusters and then precipitate as ferrihydrite along the river. The XAS results also show the by-products of neutralization-ferrihydrite and sulfate-are the primary forms of Fe and S in the sediments, respectively. Gypsum retains Cu in the sediments via structural fixation, surface adsorption, and surface coprecipitation. The difference of Cu-O coordination number between the SPM and the sediments reveals the Cu sulfate coprecipitation on the surface of gypsum accompanied by SPM transporting along the river. XAS results confirm that ferrihydrite act as an essential sink for heavy metals, especially As. As (III) mineral in the sediment near the neutralized AMD outfall is dissolved and oxidized to arsenate downstream, which then adsorb to ferrihydrite and/or form As(V)-Fe minerals along the river. Gypsum and ferrihydrite have the potential to release heavy metals with changes in water chemistry, which may pose a threat to the safety of drinking water for downstream residents. These results deepen the understanding of the influence of secondary minerals (especially gypsum and ferrihydrite) on the migration and transformation process of heavy metal pollutants in mine drainage system.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Sensitivity of geophysical techniques for monitoring secondary CO 2 storage plumes

For geologic carbon storage, the ability to detect secondary CO 2 plumes—defined as those CO 2 plumes accumulating outside the intended storage reservoir—is fundamental to preventing unexpected CO 2 migration into groundwater resources and for risk and liability management. Understanding the sensitivity of various geophysical methods to secondary plumes is crucial for designing cost-effective monitoring schemes. We use several modeling scenarios to demonstrate the process of assessing sensitivities and detection thresholds of three primary geophysical techniques—surface seismic, borehole-to-surface electromagnetic (EM), and surface and borehole gravity—for early detection of secondary CO 2 plumes in the post-injection phase. While seismic reflection methods are often considered in monitoring strategies to track the evolution of CO 2 plumes, they are also the most expensive. Due to cost considerations, especially for long-term post-injection monitoring, other techniques complement seismic monitoring when designing an adaptive monitoring network. Borehole-to-surface EM or surface gravity surveys are feasible for time-lapse monitoring of deep secondary CO 2 plumes. Furthermore, these surveys could be carried at intervals defined by site-specific conditions. If time-lapse EM and/or gravity surveys detect any signal responses beyond the expected change, it would trigger a need for the higher resolution seismic survey.

58 GEOSCIENCES↗
DOE OSTI2022

Sequence-Controlled Secondary Structures and Stimuli Responsiveness of Bioinspired Polyampholytes

In this work, a comprehensive study focusing on the influence of the sequence charge pattern on the secondary structure preferences of annealed polyampholytes and their responsiveness to external stimuli is presented. Two sequences are designed composed entirely of ionizable amino acids (charge fraction f=1), and an equal number of positive and negative charges (f + =f - =0.5) with distinct charge-patterns consisting of lysine and glutamic acid monomers. The study reveals that the sequence charge pattern has a significant influence on the secondary structure preferences of polyampholytes at physiological pH. Furthermore, it shows that external stimuli such as pH, ionic strength and solvent dielectric constant can be used to modulate the secondary structure of the two designed sequences. The observed secondary structure transformations for the two sequences are also substantially different from those determined for uniformly charged polypeptides-homo-polypeptides under matching conditions.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2026

First-principles thermodynamic assessment of Sr-containing secondary phase formation in strontium-substituted lanthanum manganites for solid oxide cell applications

Sr-secondary phase formation is a potentially significant degradation mode with direct impact upon solid-oxide cell (SOC) commercial viability. A first-principles based thermodynamic study was performed for La 1−x Sr x MnO 3±δ (LSM) perovskites to assess their stability against formation of different Sr-secondary phases, including SrO, SrCrO 4 , SrSO 4 , SrCO 3 , and Sr(OH) 2 , for SOC applications. The Sr-secondary phase formation reaction free energies were determined via a thermodynamic model by combining ab initio lattice dynamics calculations for the solid phases and ab initio thermodynamic data for the gas phases. The current approach expands the previously reported thermodynamic modeling studies by integrating first-principles based point defect equilibria into the thermodynamic analysis. The modeling results obtained using this new approach indicate an increased tendency to form the SrO oxide upon decreasing the oxygen partial pressure. Additionally, the enhancing factors to form the Sr-related secondary phase from the associated SrO activity in LSM are further quantified by considering the equilibrium of SrO reacting with the contaminant gas species as a function of temperature and pressure.

defect thermodynamics modeling↗
DOE OSTI2020

Chapter 13: Time-of-Flight Secondary-Ion Mass Spectrometry and Atom Probe Tomography

Time-of-flight secondary-ion mass spectrometry (TOF-SIMS) and atom probe tomography (APT) have many similarities. Both detect the chemical makeup of a solid material at ppm or better sensitivity, while retaining the spatial location information from the signal. Both use a similar principle to measure a signal associated with a given charged secondary ion—the flight time it takes a secondary ion to reach the detector after it is generated. Both are destructive techniques—albeit destructive of very small volumes—because the signal measured is generated by the removal of material from the sample itself. Importantly, both techniques require ultra-high vacuum (UHV) to ensure that the secondary ions, once generated, can reach the detector without collision with other atoms in the gas phase. In the case of TOF-SIMS, the samples can vary from several mm to several inches in size, whereas for APT, the samples are cones several hundred microns in size that are prepared in a special manner (covered in detail later in the chapter). We will discuss the basic fundamentals of each technique and cover several examples of the technique applied to photovoltaic materials, which should give a good idea of the types of information one can gain from TOF-SIMS and APT and how they are complementary as they both operate at different length scales: at the hundreds of microns to hundreds of nanometer scale for TOF-SIMS and at the nanometer to a few angstroms scale for APT.

41 EE - Solar Energy Technologies Office (EE-4S)↗
DOE OSTI2022

Distributed Secondary Control of Grid-Forming Inverters and AC Microgrids: Impacts of Voltage Feedback Choices

In this paper, the operational choices in distributed secondary control are examined, and their impacts on grid-forming (GFM) inverters and grid operation are investigated. In particular, the effects of feedback voltage choices, either average voltage feedback (AVF) or terminal voltage feedback (TVF), are studied with respect to reactive power sharing, voltage regulation, and grid-forming operation during black start. The secondary control used is a subgradient-based distributed cooperative control, and it provides the voltage, angle, and frequency references to the GFM inverters and their primary tracking controls. The overall control architecture employs multi-rate sampling such that the secondary control is slower than the primary control. The operational choices and their control performance are illustrated using a four-GFM-inverter microgrid in MATLAB/SIMULINK. Furthermore, the results show the effectiveness of the secondary controller, and several conclusions are drawn on the voltage feedback signals as the design choices.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2022

Supervised Learning for Distribution Secondary Systems Modeling: Improving Solar Interconnection Processes

The current interconnection process and hosting capacity analysis for distributed energy resources (DERs), such as photovoltaics (PV) and battery energy storage systems, are based on analyzing grid network constraints (voltage and thermal) using only medium-voltage distribution network models. This is because most utilities do not have secondary low-voltage system models that connect service transformers and residential customers. This is important because in many cases the main impact of interconnecting DERs could occur on the low-voltage distribution systems. This paper proposes a supervised learning method to approximate local secondary models to improve the interconnection process. The proposed supervised learning method includes a decision tree model that predicts the secondary topology and a logistic regression model that predicts conductor types. The case studies demonstrate the benefits of including secondary low-voltage circuits in the interconnection process. We report the proposed modeling methodology is readily scalable and thus can reduce the cost and effort of PV interconnection for the industry and stakeholders.

14 SOLAR ENERGY↗
DOE OSTI2025

The three cellulose synthase isoforms for secondary cell wall make specific contributions to microfibril synthesis

Cellulose is synthesized at the plasma membrane by the cellulose synthase complex, a structure that contains three distinct isoforms of the catalytic subunit, cellulose synthase A (CESA). The division into three subunits appears early in land plant evolution and is highly conserved, particularly for the secondary cell wall. However, what if any unique roles each isoform plays in the complex remain unclear. Here, we assessed the contributions of specific isoforms to microfibril synthesis. First, we expressed CESA isoforms of the primary cell wall or the moss Physcomitrium patens in Arabidopsis thaliana backgrounds missing a secondary cell wall CESA. While the primary cell wall isoforms rescued the cesa knockout phenotype with partial isoform specificity, those from the moss rescued with fewer restrictions. Then, we recreated various CESA missense mutations in all three of the secondary cell wall isoforms; while results are consistent with isoform specificity, they are difficult to interpret further without molecular structures. Finally, we show that catalytically inactive CESA isoforms restore growth and cellulose content in the corresponding knockout in an isoform-specific manner; along with partial rescue of the growth and cellulose content of the inflorescence stem, the replacement lines have fiber cells with partially disorganized microfibrils and secondary cell wall cellulose with narrow crystal width. Generally, effects were more pronounced in lines where CESA8 was inactivated compared with inactivating CESA4 or 7, which tended to have similar phenotypes to each other. Here, we account for these results with a model for cellulose synthase structure with the isoforms assigned specific localization within the cellulose synthase complex.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Uses of Multi-Objective Flux Analysis for Optimization of Microbial Production of Secondary Metabolites

Secondary metabolites are not essential for the growth of microorganisms, but they play a critical role in how microbes interact with their surroundings. In addition to this important ecological role, secondary metabolites also have a variety of agricultural, medicinal, and industrial uses, and thus the examination of secondary metabolism of plants and microbes is a growing scientific field. While the chemical production of certain secondary metabolites is possible, industrial-scale microbial production is a green and economically attractive alternative. This is even more true, given the advances in bioengineering that allow us to alter the workings of microbes in order to increase their production of compounds of interest. This type of engineering requires detailed knowledge of the “chassis” organism’s metabolism. Since the resources and the catalytic capacity of enzymes in microbes is finite, it is important to examine the tradeoffs between various bioprocesses in an engineered system and alter its working in a manner that minimally perturbs the robustness of the system while allowing for the maximum production of a product of interest. The in silico multi-objective analysis of metabolism using genome-scale models is an ideal method for such examinations.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

ECAR-6576 Rev 0 MARVEL Secondary Support Structure Analysis

The Microreactor Applications Research Validation and Evaluation (MARVEL) microreactor generates electricity using four Stirling cycle engines. Each Stirling engine, along with its mounting system, is called a Secondary Support Structure (SSS). An individual SSS consists of a Secondary Output Structure (SOS), a Secondary Support Structure Base, an insulation block, and assorted hardware. The SOS consists of the Stirling engine, the Secondary Output Structure Ring, a vibration isolator, and hardware. The purpose of this analysis is to show that the SSS is appropriately designed to meet structural, mechanical, and maintenance requirements for specified operating conditions.

21 - SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLAN↗
DOE OSTI2022

RELAP5-3D modelling of the HTTR-GT/H 2 secondary system and turbomachinery

High Temperature Gas-cooled Reactors (HTGRs) can be used for the cogeneration of electricity and hydrogen. The JAEA-operated High-Temperature engineering Test Reactor (HTTR-GT/H 2 ) is exploring using the reactor for electricity and hydrogen production. Here, a RELAP5-3D model of the HTTR-GT/H 2 secondary system has been developed using design information. The various components and heat exchangers in the secondary system were investigated, modified, and improved where applicable. With these changes made, the model was run, and the results were compared to the design conditions. The results for the sole-power generation mode were shown to fit the design conditions very well. The largest temperature difference was on the order of 7 K, and the largest pressure difference was on the order of 0.05 MPa. The results for the hydrogen cogeneration mode did not fit the design conditions as well as the other case. The largest temperature difference was about 39 K and the largest pressure difference was about 0.27 MPa at the compressor outlet. The larger differences for the hydrogen cogeneration mode are attributed to the various complex components and the flow being split in the secondary loop. A transient reduction in heat removal capability of the secondary system was investigated. Reactor temperatures were predicted to rise as a result. The core reactivity response due to this increase in temperature is investigated and is expected to add negative reactivity to the reactor.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2024

Extensive Secondary Cratering From the InSight Sol 1034a Impact Event

Abstract Impact cratering is one of the fundamental processes throughout the history of the Solar System. The formation of new impact craters on planetary bodies has been observed with repeat images from orbiting satellites. However, the time gap between images is often large enough to preclude detailed analysis of smaller‐scale features such as secondary impact craters, which are often removed or buried over a short time period. Here we use a seismic event detected on Mars by the NASA InSight mission to investigate secondary cratering at a new impact crater. We strengthen the case that the seismic event that occurred on Sol 1034 (S1034a) is the result of a new impact cratering event. Using the exact timing of this event from InSight, we investigated the resulting new impact crater in orbital image data. The S1034a impact crater is approximately 9 m in diameter but is responsible for over 900 secondary impact events in the form of low albedo spots that are located at distances of up to almost 7 km from the primary crater. We suggest that the low albedo spots formed from relatively low energy ejecta, with individual ejecta block velocities less than 200 m s −1 . We estimate that the low albedo spots, the main evidence of secondary impact processes at this new impact event, fade within 200–300 days after formation.

Grindrod, P. M. [Natural History Museum London UK]↗
DOE OSTI2022

Predictive control of selective secondary alcohol oxidation of glycerol on NiOOH

Abstract Many biomass intermediates are polyols and selectively oxidizing only a primary or secondary alcohol group is beneficial for the valorization of these intermediates. For example, production of 1,3-dihydroxyacetone, a highly valuable oxidation product of glycerol, requires selective secondary alcohol oxidation. However, selective secondary alcohol oxidation is challenging due to its steric disadvantage. This study demonstrates that NiOOH, which oxidizes alcohols via two dehydrogenation mechanisms, hydrogen atom transfer and hydride transfer, can convert glycerol to 1,3-dihydroxyacetone with high selectivity when the conditions are controlled to promote hydrogen atom transfer, favoring secondary alcohol oxidation. This rational production of 1,3-dihydroxyacetone achieved by selectively enabling one desired dehydrogenation pathway, without requiring alteration of catalyst composition, demonstrates how comprehensive mechanistic understanding can enable predictive control over selectivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗