Study of shocks and ablation front in diamond ablator during a capsule implosion experiment at the National Ignition Facility
Explore the source record for details and available documents.
Physics↗
SEARCH · Search NASA
Results for “shock ignition”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Further shock tunnel studies of scramjet phenomena
Scramjet phenomena were studied using the shock tunnel T3 at the Australian National University. Simple two dimensional models were used with a combination of wall and central injectors. Silane as an additive to hydrogen fuel was studied over a range of temperatures and pressures to evaluate its effect as an ignition aid. The film cooling effect of surface injected hydrogen was measured over a wide range of equivalence. Heat transfer measurements without injection were repeated to confirm previous indications of heating rates lower than simple flat plate predictions for laminar boundary layers in equilibrium flow. The previous results were reproduced and the discrepancies are discussed in terms of the model geometry and departures of the flow from equilibrium. In the thrust producing mode, attempts were made to increase specific impulse with wall injection. Some preliminary tests were also performed on shock induced ignition, to investigate the possibility in flight of injecting fuel upstream of the combustion chamber, where it could mix but not burn.
Morgan, R. G.↗
Pyrotechnic hazards classification and evaluation program. Electrostatic vulnerability of the E8 and XM15/XM165 clusters, phase 1
A survey of the electrostatic vulnerability of explosive manufacturing plants and recommendations for reducing the vulnerability are discussed. During the course of the investigations, the XM15/XM165 and the E8 launcher were shown to be susceptible to electrostatic ignition. The pyrotechnic hazard of prime concern associated with electrostatics is that of the spark which can be generated. The heat, shock, and ionization produced by the spark can cause ignition of pyrotechnics. However, as a result of the initial ignition tests (XM15 fuse train), changes have been incorporated to make the fusing system relatively safe from premature electrostatic activation.
Source record↗
Chemical kinetic reaction mechanism for the combustion of propane
A detailed chemical kinetic reaction mechanism for the combustion of propane is presented and discussed. The mechanism consists of 27 chemical species and 83 elementary chemical reactions. Ignition and combustion data as determined in shock tube studies were used to evaluate the mechanism. Numerical simulation of the shock tube experiments showed that the kinetic behavior predicted by the mechanism for stoichiometric mixtures is in good agrement with the experimental results over the entire temperature range examined (1150-2600K). Sensitivity and theoretical studies carried out using the mechanism revealed that hydrocarbon reactions which are involved in the formation of the HO2 radical and the H2O2 molecule are very important in the mechanism and that the observed nonlinear behavior of ignition delay time with decreasing temperature can be interpreted in terms of the increased importance of the HO2 and H2O2 reactions at the lower temperatures.
Jachimowski, C. J.↗
Simultaneous compression and opacity data from time-series radiography with a Lagrangian marker
Time-resolved radiography can be used to obtain absolute shock Hugoniot states by simultaneously measuring at least two mechanical parameters of the shock, and this technique is particularly suitable for one-dimensional converging shocks where a single experiment probes a range of pressures as the converging shock strengthens. However, at sufficiently high pressures, the shocked material becomes hot enough that the x-ray opacity falls significantly. Additionally, if the system includes a Lagrangian marker such that the mass within the marker is known, this additional information can be used to constrain the opacity as well as the Hugoniot state. In the limit that the opacity changes only on shock heating, and not significantly on subsequent isentropic compression, the opacity of the shocked material can be determined uniquely. More generally, it is necessary to assume the form of the variation of opacity with isentropic compression or to introduce multiple marker layers. Alternatively, assuming either the equation of state or the opacity, the presence of a marker layer in such experiments enables the non-assumed property to be deduced more accurately than from the radiographic density reconstruction alone. An example analysis is shown for measurements of a converging shock wave in polystyrene at the National Ignition Facility.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Fuel molecular structure effect on autoignition of highly branched iso-alkanes at low-to-intermediate temperatures: Iso-octane versus iso-dodecane
Highly branched iso-alkanes are an important class of hydrocarbons found in conventional petroleum-derived and alternative renewable fuels used for combustion applications. Recognizing that chemical kinetics for most of these iso-alkanes, especially at low-to-intermediate temperatures, has not been well studied, an experimental and modeling investigation of two selected iso-alkanes, iso-octane (2,2,4-trimethylpentane, iC8) and iso-dodecane (2,2,4,6,6-pentamethylheptane, iC12), is conducted to understand the fuel molecular structure effect on their autoignition characteristics. Using a rapid compression machine (RCM), the ignition responses of iC8 and iC12 at varying pressures, temperatures, and equivalence ratios are characterized and compared. The newly-acquired experimental ignition delay times have been compared with the literature RCM and shock tube data, demonstrating the complementary nature of the current dataset. Further comparison of the experimental pressure traces and ignition delay times illustrates the reactivity crossover between iC8 and iC12. Namely, there exists a temperature window in the negative temperature coefficient regime within which iC12 is less reactive than iC8, but iC12 becomes more reactive outside this temperature window. Furthermore, a chemical kinetic model of iso-alkanes including both iC8 and iC12 is developed. Simulated results using this model are then compared to the experimental data obtained in this study and available in the literature, showing its ability to predict the experimental trends. Chemical kinetic analyses have also been conducted to identify the important reaction pathways controlling autoignition at varying conditions, and to elucidate the underlying mechanism leading to different reactivity trends between iC8 and iC12.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Analytical and experimental investigations of the oblique detonation wave engine concept
Wave combustors, which include the oblique detonation wave engine (ODWE), are attractive propulsion concepts for hypersonic flight. These engines utilize oblique shock or detonation waves to rapidly mix, ignite, and combust the air-fuel mixture in thin zones in the combustion chamber. Benefits of these combustion systems include shorter and lighter engines which require less cooling and can provide thrust at higher Mach numbers than conventional scramjets. The wave combustor's ability to operate at lower combustor inlet pressures may allow the vehicle to operate at lower dynamic pressures which could lessen the heating loads on the airframe. The research program at NASA-Ames includes analytical studies of the ODWE combustor using Computational Fluid Dynamics (CFD) codes which fully couple finite rate chemistry with fluid dynamics. In addition, experimental proof-of-concept studies are being performed in an arc heated hypersonic wind tunnel. Several fuel injection design were studied analytically and experimentally. In-stream strut fuel injectors were chosen to provide good mixing with minimal stagnation pressure losses. Measurements of flow field properties behind the oblique wave are compared to analytical predictions.
Menees, Gene P.↗
Analytical and experimental investigations of the oblique detonation wave engine concept
Wave combustors, which include the Oblique Detonation Wave Engine (ODWE), are attractive propulsion concepts for hypersonic flight. These engines utilize oblique shock or detonation waves to rapidly mix, ignite, and combust the air-fuel mixture in thin zones in the combustion chamber. Benefits of these combustion systems include shorter and lighter engines which will require less cooling and can provide thrust at higher Mach numbers than conventional scramjets. The wave combustor's ability to operate at lower combustor inlet pressures may allow the vehicle to operate at lower dynamic pressures which could lessen the heating loads on the airframe. The research program at NASA-Ames includes analytical studies of the ODWE combustor using CFD codes which fully couple finite rate chemistry with fluid dynamics. In addition, experimental proof-of-concept studies are being carried out in an arc heated hypersonic wind tunnel. Several fuel injection designs were studied analytically and experimentally. In-stream strut fuel injectors were chosen to provide good mixing with minimal stagnation pressure losses. Measurements of flow field properties behind the oblique wave are compared to analytical predictions.
Menees, Gene P.↗
TPSAS-NF1676L-32540-DND
The supersonic/hypersonic ground testing serves a multitude of purposes and objectives. From structural and material integrity, to force and moment models; from pressure mapping, thermal imaging, shock structure to scramjet/ramjet engine operability and ignition studies. Hypersonics has become more of a high profile area of late. Compared to flight testing, ground testing typically it is less expensive and usually is not a one single-test test program. It is more forgiving in the fact that a test program can utilize a single test article and get data from a number of tests. Ground test data is the input to the formation of research databases, as well as, validation of CFD models/tools. To understand the output, one must first understand the inputs. To achieve supersonic/hypersonic speeds the use of compressors or compressed air storage along with converging-diverging nozzles are needed. Flight temperatures also need to be achieved for the ground test to truly simulate flight conditions. At NASA Langley's 8' High Temperature Tunnel (HTT), compressed natural gas (methane) is burned to heat the air. To validate that the desired test condition is met, test instrumentation is used and data is collected from the combustor all the way through the nozzle exit plane. In this talk, NASA Langley's 8' HTT will be the basis for what kind of test capabilities hypersonic ground testing offers. It certainly does not offer every capability within ground testing, nor will the discussion cover all types. Specific test techniques used and data collection methods will be discussed and how these confirm certain flight conditions have been achieved. There will be subsequent thoughts on experimental methods that aid test articles such as thrust stands, model actuation, etc.
Aaron W Fuchs↗
A detailed chemical kinetic modeling and experimental investigation of the low- and high-temperature chemistry of n-butylcyclohexane
Chemical kinetic models of gasoline, jet, and diesel fuels and their mixtures with bioderived fuels are needed to assess fuel property effects on efficiency, emissions, and other performance metrics in internal combustion and gas turbine engines. As these real fuels have too many fuel components to be included in a chemical kinetic model, surrogate fuels containing fewer components are used to represent them. These surrogate fuels mimic the chemical classes or molecular structures contained in the real fuel. One of the important chemical classes in gasoline, jet, and diesel fuels comprises cyclohexanes. Cyclohexanes comprise about 30% or more by weight in diesel fuel. Also, Mueller et al proposed n-butylcyclohexane (nBCH) as a component in a nine-component surrogate palette to represent the ignition properties, distillation curve, density, and molecular structures of a diesel certification fuel. Herein, experimental measurements of the ignition delay times (IDTs) of nBCH in a shock tube and in a rapid compression machine are reported over a wide range of temperature, pressure, and equivalence ratio important for enabling the validation of a chemical kinetic model for nBCH for combustion in diesel engines. The range of conditions are temperatures of 630–1420 K, pressures of 10, 30, and 50 bar, and equivalence ratios of 0.3, 0.5, 1.0, and 2.0 in ‘air’. A detailed chemical model is developed for nBCH to simulate its ignition at both low and high-temperature conditions and at relevant elevated pressures. The experimentally measured IDTs are used to improve and validate the chemical kinetic model.
32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
High-Fuel Loading Ignition Delay Time Characterization of Hydrogen/Natural Gas/Ammonia at Gas Turbine-Relevant Conditions Inside a High-Pressure Shock Tube
Abstract This study explores the combustion characterization of high-fuel percentage, air-diluted mixtures of H2 mixed with natural gas (NG) as well as mixtures of H2 and NH3 at temperatures and pressures relevant to turbine operating conditions (20–30 bar, 1000–1500 K). Lower temperatures (below 1070 K) exhibit preignition characteristics due to non-homogeneity. An attempt to mitigate these occurrences at high pressures is investigated using the constrained reaction volume (CRV) stage-filling technique. Due to the need to further refine the facility CRV stage-filling uncertainty, only higher temperature data will be interpreted at this time. The test conditions in this study closely replicate the temperatures, pressures, and mixtures that would be seen in hydrogen-powered gas turbines, making it the first to explore such conditions. The experimental IDTs were compared against the current state-of-the-art chemical kinetic models for mechanism validation. The current work will advance H2-powered turbines and aims to determine the optimum molecular ratio of H2 when mixed with natural gas.
Pierro, Michael↗
The driving mode of shock-driven turbulence
Turbulence in the interstellar medium (ISM) is crucial in the process of star formation. Shocks produced by supernova explosions, jets, radiation from massive stars, or galactic spiral-arm dynamics are amongst the most common drivers of turbulence in the ISM. However, it is not fully understood how shocks drive turbulence, in particular whether shock driving is a more solenoidal (rotational, divergence-free) or a more compressive (potential, curl-free) mode of driving turbulence. The mode of turbulence driving has profound consequences for star formation, with compressive driving producing three times larger density dispersion, and an order of magnitude higher star formation rate than solenoidal driving. Here, we use hydrodynamical simulations of a shock inducing turbulent motions in a structured, multiphase medium. This is done in the context of a laser-induced shock, propagating into a foam material, in preparation for an experiment to be performed at the National Ignition Facility (NIF). Specifically, we analyse the density and velocity distributions in the shocked turbulent medium, and measure the turbulence driving parameter $b=(\sigma _{\rho /\langle \rho \rangle }^{2\Gamma }-1)^{1/2}(1-\sigma _{\rho /\langle \rho \rangle }^{-2})^{-1/2}\mathcal {M}^{-1}\Gamma ^{-1/2}$, with the density dispersion σρ/<ρ>, the turbulent Mach number $\mathcal {M}$, and the polytropic exponent Γ. Purely solenoidal and purely compressive driving correspond to b ~ 1/3 and b ~ 1, respectively. As a result, using simulations in which a shock is driven into a multiphase medium with structures of different sizes and Γ < 1, we find b ~ 1 for all cases, showing that shock-driven turbulence is consistent with strongly compressive driving.
79 ASTRONOMY AND ASTROPHYSICS↗
Fundamental Experimental Tests and Modeling of LOX/CH4 Engines at High Pressures
In recent years, the space travel industry has grown exponentially, resulting in the need for a low-cost, efficient rocket engine fuel. As such, there has been renewed interest in utilizing liquid natural gas (LNG) as it is less likely to soot than kerosene-based fuels and has widespread availability and low cost of use as compared to the traditional RP-X and even liquid methane (LCH4) fuels due to the reduced need for refinement. However, current literature does not fully cover varying blends of natural gas and the effects that impurities have on natural gas/methane fuels, with most studies being confined to low-pressure applications. Therefore, new experimental ignition delay time measurements at rocket engine relevant pressures are essential to ensure current chemical kinetic models capture the ignition behavior at these elevated conditions and to determine the optimal purity levels for a reliable, cost-efficient, aerospace-grade LCH4/LNG fuel. The current work explores various blends of natural gas/methane fuel with various impurities, including higher hydrocarbons as well as nitrogen-carriers. A shock tube study was carried out to study the ignition delay times and carbon monoxide time histories of these natural gas blends utilizing chemiluminescence and laser absorption spectroscopy at 20, 50 and 100 atm over temperatures ranging from 1400-1700K and at an equivalence ratio of 1. The experimental data was then compared to two different chemical kinetic mechanisms: the industry-standard GRI 3.0 and the in-house UCF 2022. The data is used to improve chemical kinetic mechanisms and modeling of LNG fuels for rocket engine applications.
Methane↗
VIPIR: A High-Throughput Drop-Weight Impact Instrument for Imaging the Initiation and Propagation of Reactions in Energetic Materials
Characterizing the handling safety and sensitivity of explosives has been a challenging area of study for over 60 years. Historically one of the most accessible and widely utilized experiments has been the drop-weight impact test, which involves dropping a weight on a small sample sandwiched between two anvils. Because this experiment generally only utilizes sound thresholds to determine whether or not a sample reacted, the physical and chemical properties governing sensitivity remain convolved. Better understanding of chemical and material characteristics is needed to give the chemistry and engineering communities a predictive tool to determine the handling sensitivity of explosives prior to pursuing expensive and potentially hazardous synthesis and formulation operations. Here, we are developing a high throughput drop tower instrument capable of imaging the deformation and flow of energetic materials during impact and the resulting thermal ignition and propagation events. This instrument is based on previous designs but has been modified for higher throughput and tailorable modifications in the future. Herein, we present key design features that enable high-speed visible and thermal imaging of explosive initiation by sub-shock impacts, as well as preliminary results in which ignition sites were observed in an erythritol tetranitrate sample.
47 OTHER INSTRUMENTATION↗
Shock tube investigation of high-temperature, extremely-rich oxidation of several co-optima biofuels for spark-ignition engines
To reduce the reliance on fossil fuels in the transportation sector and increase combustion efficiency, the Co-Optima initiative from US Department of Energy identified the top 10 biofuels for downsized, boosted, spark-ignition engines. Most of these biofuels have detailed reaction mechanisms available in literature developed based on studies at temperatures lower than 1700 K and an equivalence ratio of less than five. As such, the performance of these detailed mechanisms at high temperature and extremely rich conditions are unknown. It is important to validate kinetic mechanisms at these conditions because they are conducive to soot formation. Prediction of soot by chemical kinetic models relies on the prediction of underlying benchmark species like carbon monoxide and ethylene. In this work, we conduct high temperature (1700–2050 K) and high equivalence ratio(Φ=8.6) oxidation of these biofuels, namely 2,4,4-trimethyl-1-pentene (α-diisobutylene), ethanol, cyclopentanone, methyl acetate, and 2-methylfuran, blended in ethylene behind reflected shock waves at 4–4.7 atm pressure. Carbon monoxide and ethylene time histories are measured simultaneously using a continuous feedback quantum cascade laser near 4.9 µm and a tunable CO 2 gas laser at 10.532 nm, respectively. Results show that ethanol blend forms more carbon monoxide than other biofuels and consumes ethylene faster than the biofuel blends in the temperature range considered. Overall, the performance of different mechanisms in literature are evaluated against the experimental results. The novel reaction mechanism ‘the Co-Optima model’, which includes the sub mechanisms for all the biofuels in this study, was found to be the best mechanism for the experimental conditions studied.
32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
Ignition delay times of benzene and toluene with oxygen in argon mixtures
The ignition delay times of benzene and toluene with oxygen diluted in argon were investigated over a wide range of conditions. For benzene the concentration ranges were 0.42 to 1.69 percent fuel and 3.78 to 20.3 percent oxygen. The temperature range was 1212 to 1748 K and the reflected shock pressures were 1.7 to 7.89 atm. Statistical evaluation of the benzene experiments provided an overall equation which is given. For toluene the concentration ranges were 0.5 to 1.5 percent fuel and 4.48 to 13.45 percent oxygen. The temperature range was 1339 to 1797 K and the reflected shock pressures were 1.95 to 8.85 atm. The overall ignition delay equation for toluene after a statistical evaluation is also given. Detailed experimental information is provided.
Burcat, A.↗
A Computational Study of the Thermodynamic Conditions Leading to Autoignition in Nanosecond Pulsed Discharges
Nanosecond pulsed discharges have attracted the attention of engine manufacturers due to the possibility of attaining distributed ignition sites that accelerate burn rates while resulting in very little electrode erosion. Multidimensional modeling tools currently capture the electrical structure of such discharges accurately, but resolving the chemical structure remains a challenging problem owing to the disparity of time-scales in streamer propagation (nanoseconds) and ignition phenomena (microseconds). The purpose of this study is to extend multidimensional results toward resolving the chemical structure in the wake of streamers (or the afterglow) by using a batch reactor model (BRM). This can afford the use of very detailed chemical kinetic information. The full nonequilibrium nature of the electrons is taken into account, along with fast gas heating, shock wave propagation, and thermal diffusion. The results shed light on ignition phenomena brought about by such discharges.
42 ENGINEERING↗
A High-Pressure Shock Tube Study of Hydrogen and Ammonia Addition to Natural Gas for Reduced Carbon Emissions in Power Generation Gas Turbines
Ignition delay times from undiluted mixtures of natural gas (NG)/H2/Air and NG/NH3/Air were measured using a high-pressure shock tube at the University of Central Florida. The combustion temperatures were experimentally tested between 1000-1500 K near a constant pressure of 25 bar. Mixtures were kept undiluted to replicate the same chemistry pathways seen in gas turbine combustion chambers. Recorded combustion pressures exceeded 200 bar due to the large energy release, hence why these were performed at the high-pressure shock tube facility. The data is compared to the predictions of the NUIGMech 1.1 mechanism for chemical kinetic model validation and refinement. An exceptional agreement was shown for stoichiometric conditions in all cases but strayed at lean and rich equivalence ratios, especially in the lower temperature regime of H2 addition and all temperature ranges of the baseline NG mixture. Hydrogen addition also decreased ignition delay times by nearly 90%, while NH3 fuel addition made no noticeable difference in ignition delay time. NG/NH3 exhibited similar chemistry to pure NG under the same conditions, which is shown in a sensitivity analysis, demonstrating hydrogen chemistry to be dominant in NG/H2 mixtures and hydrocarbon chemistry to be dominant in NG/NH3 mixtures. The reaction CH3 + O2 = CH3O + O is identified and suggested as a possible modification target to improve model performance. Increasing the robustness of chemical kinetic models via experimental validation will directly aid in designing next-generation combustion chambers for use in gas turbines, which in turn will greatly lower global emissions and reduce greenhouse effects.
Pierro, Michael↗