Search NASA⌕ Search

SEARCH · Search NASA

Results for “shuttling effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Performance, static stability, and control effectiveness of a parametric space shuttle launch vehicle

This test was run as a continuation of a prior investigation of aerodynamic performance and static stability tests for a parametric space shuttle launch vehicle. The purposes of this test were: (1) to obtain a more complete set of data in the transonic flight region, (2) to investigate new H-0 tank noseshapes and tank diameters, (3) to obtain control effectiveness data for the orbiter at 0 degree incidence and with a smaller diameter H-0 tank, and (4) to determine the effects of varying solid rocket motor-to-H0 tank gap size. Experimental data were obtained for angles of attack from -10 to +10 degrees and for angles of sideslip from +10 to -10 degrees at Mach numbers ranging from .6 to 4.96.

Buchholz, R. E.↗
NASA NTRS1983

Evaluation of mounting bolt loads for Space Shuttle Get Away Special (GAS) adapter beam

During the prototype vibration tests of the GAS adapter beam, significant impacting of the beam at its support points was observed. The cause of the impacting was traced to gaps under the mounting bolt heads. Because of the nonlinear nature of the response, it was difficult to evaluate the effects which Shuttle launch dynamics might have on the mounting bolt loads. A series of tests were conducted on an electrodynamic exciter in which the transient acceleration time histories, which had been measured during the Space Transportation System-1 (STS-1; Space Shuttle mission 1) launch, were simulated. The actual flight data had to be filtered and compensated so that it could be reproduced on the shaker without exceeding displacement and velocity limitations. Mounting bolt loads were measured directly by strain gages applied to the bolts. Various gap thicknesses and bolt torques were investigated. Although increased gap thickness resulted in greater accelerations due to impacting, the bolt loads were not significantly affected. This is attributed to the fact that impacting excited mostly higher frequency modes which do not have significant modal mass.

Talapatra, D. C.↗
NASA NTRS1982

Experimental investigation of gamma effects on heat transfer to a 0.006 scale Shuttle Orbiter at Mach 6

Real-gas effects on heating to the windward centerline of the Shuttle Orbiter and shock shape were simulated by testing a 0.006-scale Orbiter model in Mach 6 air and CF4 flows. The range of free-stream Reynolds number, based on model length, was 0.4 x 10 to the 6th to 5.3 x 10 to the 6th for air, resulting in laminar and turbulent heating. The Reynolds number for CF4 was 0.3 x 10 to the 6th and gamma was equal to 1.13, corresponding to a normal shock density ratio of 12 as compared to 5.25 in air. Angle of attack was varied from 15 deg to 45 deg in 5 deg increments. Centerline heating distributions were compared for the two gases, and to Mach 8 wind-tunnel data, predictions, and flight (STS-1 and STS-2) data. The present results revealed a significant increase in heating with increasing density ratio and decreasing Reynolds number at the lower angles of attack; the effects of density ratio and Reynolds number diminished with increasing angle of attack and were relatively small at the angles of attack for the hypersonic portion of Space Shuttle Orbiter flights STS-1 and STS-2. Wind-tunnel and flight heating distributions were in relatively good agreement, and the present heating rates in air were accurately predicted by a local infinite swept cylinder analysis.

Miller, C. G.↗
NASA NTRS1974

Data correlation and analysis of arc tunnel and wind tunnel tests of RSI joints and gaps. Volume 2: Data base

Wind tunnel tests were conducted to determine the aerodynamic heating created by gaps in the reusable surface insulation (RSI) thermal protection system (TPS) for the space shuttle. The effects of various parameters of the RSI on convective heating characteristics are described. The wind tunnel tests provided a data base for accurate assessment of gap heating. Analysis and correlation of the data provide methods for predicting heating in the RSI gaps on the space shuttle.

Christensen, H. E.↗
NASA NTRS1983

Airborne measurements of Space Shuttle exhaust constituents

Airborne measurements of hydrogen chloride (HCl) and particulates made during penetrations into and flights under Space Shuttle exhaust clouds from launches STS-1, -2, and -5 are presented to permit comparison with dispersion model predictions for Space Shuttle exhaust clouds, and with previous measurements made in Titan III exhaust clouds. Analytical techniques employed for the Shuttle measurements were developed and refined during earlier Titan III exhaust cloud measurements and include the measurements of particulate concentrations, size distributions, and the partitioning of HCl between the gaseous and aerosol phases. The results are useful in understanding the dynamics of ground cloud development, atmospheric dispersion, and potential environmental effects of Shuttle effluents.

Cofer, W. R., III↗
NASA NTRS2004

Simulation of Foam Impact Effects on Components of the Space Shuttle Thermal Protection System

A series of three dimensional simulations has been performed to investigate analytically the effect of insulating foam impacts on ceramic tile and reinforced carbon-carbon components of the Space Shuttle thermal protection system. The simulations employed a hybrid particle-finite element method and a parallel code developed for use in spacecraft design applications. The conclusions suggested by the numerical study are in general consistent with experiment. The results emphasize the need for additional material testing work on the dynamic mechanical response of thermal protection system materials, and additional impact experiments for use in validating computational models of impact effects.

Fahrenthold, Eric P.↗
NASA NTRS1978

Effects of data asymmetry on Shuttle Ku-band communications link performance

This paper systematically analyzes the signal-to-noise ratio degradations which can potentially occur due to data asymmetry in digital transmission systems. Suitable asymmetry models are developed and error probability performance for various types of data detectors (integrate-and-dump filter, filter-sample detector, and gated-integrate-and-dump filter) is derived. Although this work was done to resolve problems being encountered in the Shuttle Ku-band return link design, specifically for the 50 Mbit/s convolutionally encoded channel (NRZ format), generalizations are made which provide results for other cases of interest (other Ku-band return link channels, or other systems entirely). This paper therefore considers Manchester data formats (in addition to NRZ) and uncoded transmission (in addition to convolutionally coded transmission). The effects of bandlimiting are also considered.

Simon, M. K.↗
NASA NTRS1980

Study of power management technology for orbital multi-100KWe applications. Volume 2: Study results

The preliminary requirements and technology advances required for cost effective space power management systems for multi-100 kilowatt requirements were identified. System requirements were defined by establishing a baseline space platform in the 250 KE KWe range and examining typical user loads and interfaces. The most critical design parameters identified for detailed analysis include: increased distribution voltages and space plasma losses, the choice between ac and dc distribution systems, shuttle servicing effects on reliability, life cycle costs, and frequency impacts to power management system and payload systems for AC transmission. The first choice for a power management system for this kind of application and size range is a hybrid ac/dc combination with the following major features: modular design and construction-sized minimum weight/life cycle cost; high voltage transmission (100 Vac RMS); medium voltage array or = 440 Vdc); resonant inversion; transformer rotary joint; high frequency power transmission line or = 20 KHz); energy storage on array side or rotary joint; fully redundant; and 10 year life with minimal replacement and repair.

Mildice, J. W.↗
NASA NTRS1985

Space Shuttle booster thrust imbalance analysis

An analysis of the Shuttle SRM thrust imbalance during the steady-state and tailoff portions of the boost phase of flight are presented. Results from flights STS-1 through STS-13 are included. A statistical analysis of the observed thrust imbalance data is presented. A 3 sigma thrust imbalance history versus time was generated from the observed data and is compared to the vehicle design requirements. The effect on Shuttle thrust imbalance from the use of replacement SRM segments is predicted. Comparisons of observed thrust imbalances with respect to predicted imbalances are presented for the two space shuttle flights which used replacement aft segments (STS-9 and STS-13).

Bailey, W. R.↗
NASA NTRS1975

Cost effective dynamic design and test requirements for Shuttle payloads

The results of a study examining current spacecraft dynamic design and test requirements for the cost effective design and development of Shuttle payloads are presented. Dynamic environments, payload configurations, design/test requirements, test levels, assembly level of testing, simulation methods, prototype role, load limiting, test facilities, and flight measurements are discussed as they relate to the development of a cost effective design and test philosophy for Shuttle Spacelab payloads. It is concluded that changes to current design/test practices will minimize long range payload costs. However, changes to current practices need be quantitatively evaluated before an orderly progression to more cost effective methods can be achieved without undue risk of mission failures. Of major importance is optimization of test levels and plans for payloads and payload subsystems which will result in minimum project costs.

Stahle, C. V.↗
NASA NTRS1999

Effects of Promethazine on Performance During Simulated Shuttle Landings

Promethazine (PMZ) is the antimotion sickness drug of choice in the U.S. Space Shuttle program; however, virtually nothing is known about the bioavailability and performance effects of this drug in the microgravity environment. PMZ has detrimental side effects on human performance on Earth that could affect Shuttle operations. In a recent ground-based study we examined: 1) the effects of promethazine (PMZ) on Shuttle landing performance using the portable inflight landing operations trainer (PILOT), and 2) saliva and urine samples to determine the pharmacokinetics of PMZ. The PILOT performance data is presented here.

Harm, D. L.↗
NASA NTRS1981

Numerical simulation of reentry flow around the Shuttle Orbiter including real gas effects

The flight environment of a reentry vehicle is predicted from the numerical solution of fluid dynamics equations for the region between the blunt nose and the swept wings. The inviscid portion of the shock layer is modeled by the Euler equations, but the laminar viscous flow adjacent to the wall is modeled by the approximate parabolic Navier-Stokes equations. The approximations made to the axial gradients of pressure and diffusive fluxes enable the coupled inviscid and viscous equations to be solved efficiently along the body axis. The equilibrium air aftbody code contains significant improvements over its predecessor which only considers a perfect gas model and noncircular configurations. The inclusion of numerical damping either explicitly or implicitly has extended its capabilities for predicting flow field around a winged configuration at higher Machs and greater angles of attack. The results are obtained on the cylindrical coordinates and satisfactory for the Shuttle Orbiter at a free-stream Mach number of 22 and an angle of attack of 40 deg. Also discussed are the inviscid formulation and its application for wind-tunnel conditions.

Li, C. P.↗
NASA NTRS1972

Space shuttle: Static aerodynamic characteristics and control effectiveness of two delta wing orbiter configurations (M equals 0.6 to 4.96)

Two 0.00325-scale models of a space shuttle orbiter were tested in trisonic wind tunnel to obtain force, static stability, and control effectiveness data by six component internal strain gauge balance. Two separate configurations were tested; however, the fuselage and basic wing were of one-piece construction. The configurations were varied by replacing the straight wing tip extensions with upswept wing tips. Directional stability was provided for one configuration by a centerline vertical tail. Due to the one-piece body/wing construction, no body-alone data were obtained. The effect of tip fins and vertical tail size were, however, investigated. Both configurations were tested over a Mach range of 0.6 to 4.96 with data taken at angles of attack from minus 4 deg to 60 deg and at angles of sideslip from minus 4 deg to 10 deg.

Ellis, R. R.↗
NASA NTRS1986

Plasma diagnostics package measurements of ionospheric ions and Shuttle-induced perturbations

The plasma diagnostics package (PDP) on the Space Shuttle STS-3 mission in March 1982 carried among its instrument complement a retarding potential analyzer. This instrument measured both the ambient ion plasma density and temperature, and perturbations to the plasma produced by Shuttle Orbiter effects. Whenever the plasma flow streamline at the instrument was more than a distance of the order of thermal ion gyroradii away from any Orbiter surface, the measurements were characteristic of the ambient ionosphere. In several situations, the PDP was positioned so as to scan the wake in the plasma flow produced by Orbiter surfaces. The density profile of the major species O(+) was consistent with a classic Mach cone. However, strong perturbations extended for several meters outside the Mach cone, which resulted in failure of flowing Maxwellian distributions to represent the data. Configurations where the plasma-flow-impacted Orbiter surfaced downstream of the PDP resulted in generation of a suprathermal ion component. The observations are discussed in terms of a recent model of the mechanism for generation of Shuttle glow.

Reasoner, David L.↗
NASA NTRS1996

Calbindins decreased after space flight

Exposure of the body to microgravity during space flight causes a series of well-documented changes in Ca2+ metabolism, yet the cellular and molecular mechanisms leading to these changes are poorly understood. Calbindins, vitamin D-dependent Ca2+ binding proteins, are believed to have a significant role in maintaining cellular Ca2+ homeostasis. In this study, we used biochemical and immunocytochemical approaches to analyze the expression of calbindin-D28k and calbindin-D9k in kidneys, small intestine, and pancreas of rats flown for 9 d aboard the space shuttle. The effects of microgravity on calbindins in rats from space were compared with synchronous Animal Enclosure Module controls, modeled weightlessness animals (tail suspension), and their controls. Exposure to microgravity resulted in a significant and sustained decrease in calbindin-D28k content in the kidney and calbindin-D9k in the small intestine of flight animals, as measured by enzyme-linked immunosorbent assay (ELISA). Modeled weightlessness animals exhibited a similar decrease in calbindins by ELISA. Immunocytochemistry (ICC) in combination with quantitative computer image analysis was used to measure in situ the expression of calbindins in the kidney and the small intestine, and the expression of insulin in pancreas. There was a large decrease of immunoreactivity in renal distal tubular cell-associated calbindin-D28k and in intestinal absorptive cell-associated calbindin-D9k of space flight and modeled weightlessness animals compared with matched controls. No consistent difference in pancreatic insulin immunoreactivity between space flight, modeled weightlessness, and controls was observed. Regression analysis of results obtained by quantitative ICC and ELISA for space flight, modeled weightlessness animals, and their controls demonstrated a significant correlation. These findings after a short-term exposure to microgravity or modeled weightlessness suggest that a decreased expression of calbindins may contribute to the disorders of Ca2+ metabolism induced by space flight.

Non-NASA Center↗
NASA NTRS1979

An experimental investigation to determine the effect of window cooling by mass injection for the Shuttle Infrared Leeside Temperature Sensing (SILTS) experiment

The effect of mass injection on the shuttle infrared leeside temperature sensing (SILTS) pod window surfaces in reducing window heating and minimizing window lens radiation during the reentry data taking period is investigated. Heat transfer coefficients on and around the simulated windows and window cavities are determined. Heat transfer rates and window coolant flow rates are reported for the SILTS configuration. A comparison of two windows' geometries and their effects on the heat transfer rate is discussed and oil flow photographs are presented to indicate how mass injection affects the flow field near the SILTS window.

Bradley, P. F.↗
NASA NTRS1972

Effects of cruise engine location and power on interference

Data are presented, in plotted form, of tests for determining the interference effects of space shuttle booster cruise engine location for power-on and power-off conditions. The tests were conducted in a 7 x 10 foot transonic wind tunnel; the model was a 0.015-scale space shuttle booster specially equipped for propulsion effects testing. Data were obtained over a Mach number range of 0.4 to 1.13 at angles of attack from -4 deg to 20 deg at zero degrees sideslip and at angles of sideslip from -6 deg to +6 deg at constant angles of attack of 0 deg, 6 deg, 15 deg, and in some cases 10 deg. Additional parameters investigated were: elevon deflection, canard deflection, aileron deflection, rudder deflection, canard position, and mass flow rate.

Bradley, D.↗