Search NASA⌕ Search

SEARCH · Search NASA

Results for “silicon dioxide”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

The effect of phosphorus and sulfur treatment on the surface properties of InP

Experimental results are presented for InP surfaces treated by using red phosphorus as a source to create an excess overpressure of phosphorus during annealing and prior to silicon dioxide deposition. The surface has been probed by in situ photoluminescence, noncontacting remote gate C-V, and conventional high-frequency and quasi-static C-V methods. A study has also been made of the surface of sulfurized InP following heating in aqueous (NH4)2S(x). MISFETs fabricated using the benefits of these surface treatments show high transconductances and stabilities approaching those of thermal SiO2/Si with less than 5-percent variation in drain current over a 12-hr period.

Iyer, R.↗
NASA NTRS1989

Durable thin film coatings for reflectors used in low earth orbit

This paper discusses the properties of thin film coatings used to provide a durable reflective surface for solar concentrators used in the solar dynamic system designed for the Space Station. The material system to be used consists of an adhesion promotion layer, a silver reflective layer, and a protective layer of aluminum oxide and silicon dioxide. The performance characteristics of this system are described and compared to those of several alternative systems which use aluminum as the reflective layer.

Mcclure, Donald J.↗
NASA NTRS1990

High frequency capacitance-voltage characteristics of thermally grown SiO2 films on beta-SiC

Silicon dioxide films grown under dry and wet oxidation environment on beta-SiC films have been studied. The beta-SiC films had been heteroepitaxially grown on both on-axis and 2-deg off-axis (001) Si substrates. Capacitance-voltage and conductance-voltage characteristics of metal-oxide-semiconductor structures were measured in a frequency range of 10 kHz to 1 MHz. From these measurements, the interface trap density and the effective fixed oxide charge density were observed to be generally lower for off-axis samples.

Tang, S. M.↗
NASA NTRS1989

Photovoltaic array environmental protection program

During the photovoltaic array environmental protection program, a coating material, application technique, and design approach intended to protect flexible solar array blankets during a nominal fifteen-year operating lifetime were developed. Numerous thin-film coatings for protecting the Kapton polyimide material used in the construction of the Space Station Freedom flexible solar array blanket were evaluated. The critical solar array design features and protection measures are discussed with special emphasis on the effects of solar array fabrication and flexible printed circuit manufacturing processes on coating durability. The results of the mechanical and environmental test evaluation, including oxygen plasma, neutral oxygen beam, and UV/charged-particle combined exposure, are discussed. These results led to the selection of a silicon dioxide thin-film coating to protect the solar array blanket from the low-earth-orbit atomic oxygen environment.

Bilger, Kevin M.↗
NASA NTRS1991

Fast-Acting Rubber-To-Coated-Aluminum Adhesive

Cyanoacrylate adhesive used to join rubber to coated aluminum easier to apply and more effective. One-part material applied in single coat to aluminum treated previously with epoxy primer and top coat. Parts mated as soon as adhesive applied; no drying necessary. Sets in 5 minutes. Optionally, accelerator brushed onto aluminum to reduce setting time to 30 seconds. Clamping parts together unnecessary. Adhesive comes in four formulations, all based on ethyl cyanoacrylate with various amounts of ethylene copolymer rubber, poly(methyl methacrylate), silicon dioxide, hydroquinone, and phthalic anhydride.

Comer, Dawn A.↗
NASA NTRS1991

Stacked-Gate FET's For Analog Memory Elements

Three-terminal, double-stacked-gate field-effect transistor (FET), developed as analog memory element. Particularly suited for use as synapse with variable connection strength in electronic neural network. Provides programmable, nonvolatile resistive connection, somewhat in manner of porous-gate FET described in "Porous-Floating-Gate Field-Effect Transistor" (NPO-17532). Resembles commercial erasable programmable read-only memory (EPROM) device, except for thickness of layers of silicon dioxide electrically isolating gates. Either p-channel or n-channel device.

Thakoor, Anilkumar P.↗
NASA NTRS1990

Simulation of Martian dust accumulation on surfaces

Future NASA space missions include the possibility of manned landings and exploration of Mars. Environmental and operational constraints unique to Mars must be considered when selecting and designing the power system to be used on the Mars surface. A technique is described which was developed to simulate the deposition of dust on surfaces. Three kinds of dust materials were studied: aluminum oxide, basalt, and iron oxide. The apparatus was designed using the Stokes and Stokes-Cunningham law for particle fallout, with additional consideration given to particle size and shape. Characterization of the resulting dust films on silicon dioxide, polytetrafluoroethylene, indium tin oxide, diamondlike carbon, and other surfaces are discussed based on optical transmittance measurements. The results of these experiments will guide future studies which will consider processes to remove the dust from surfaces under Martian environmental conditions.

Perez-Davis, Marla E.↗
NASA NTRS1991

The effect of atomic oxygen on polysiloxane-polyimide for spacecraft applications in low Earth orbit

Polysiloxane-polyimide films are of interest as a replacement for polyimide Kapton in the Space Station Freedom solar array blanket. The blanket provides the structural support for the solar cells as well as providing transport of heat away from the back of the cells. Polyimide Kapton would be an ideal material to use; however, its high rate of degradation due to attack by atomic oxygen in low Earth orbit, at the altitudes Space Station Freedom will fly, is of such magnitude that if left unprotected, the blanket will undergo structural failure in much less than the desired 15 year operating life. Polysiloxane-polyimide is of interest as a replacement material because it should from its own protective silicon dioxide coating upon exposure to atomic oxygen. Mass, optical, and photomicrographic data obtained in the evaluation of the durability of polysiloxane-polyimide to an atomic oxygen environment are presented.

Rutledge, Sharon K.↗
NASA NTRS1991

Migration and generation of contaminants from launch through recovery: LDEF case history

The migration of contaminants to and between Long Duration Exposure Facility (LDEF) surfaces reveals new information relevant to all future space missions. The surface of the LDEF satellite closely paralleled over seven meters of the shuttle during one launch and one reentry. Transfer of contaminants from the shuttle bay to the payload were documented and partially quantified for both the launch and recovery separately. LDEF carried a load of volatile silicones and hydrocarbons into orbit which were then polymerized by UV radiation into tough, dark brown stains on exposed surfaces. The distribution of these stains is providing new information on deposition mechanisms that should be studied on future missions. Electrostatic effects, diffusional flow, and effects due to small surface temperature differences at the time of UV exposure are suggested. The types of functional groups present in the LDEF deposit it nearly identical to stains recovered from other spacecraft. These stains were remarkably stable in low Earth orbit even with atomic oxygen exposure if the amount of silicones present was sufficient to create a sealing layer of silicon dioxide over the dark brown stain beneath.

Crutcher, E. Russ↗
NASA NTRS1990

Materials degradation in low earth orbit (LEO); Proceedings of the Symposium, 119th Annual Meeting of the Minerals, Metals, and Materials Society, Anaheim, CA, Feb. 17-22, 1990

The current understanding of the effect of space environment on materials and the development of protective coatings is examined in reviews and reports. Consideration is given to hyperthermal atomic oxygen reactions, the effect of atomic oxygen on altered and coated Kapton surfaces for spacecraft applications in LEO, silicon dioxide space coatings studied ellipsometrically, atomic oxygen effects on spacecraft materials, atomic oxygen beam source for erosion simulation, and atomic oxygen effects on refractory materials. Particular attention is given to ellipsometric analysis of materials degradation in space, studies of the interaction of 8 km/s oxygen atoms with selected materials, characterization and calibration of the EOIM-III flight mass spectrometer in a high velocity oxygen atom beam, the reaction efficiency of thermal energy oxygen atoms with polymeric materials, and effects of simulated space environments on the properties of selected materials.

Srinivasan, V.↗
NASA NTRS1992

Fabrication of Thin Film Heat Flux Sensors

Prototype thin film heat flux sensors have been constructed and tested. The sensors can be applied to propulsion system materials and components. The sensors can provide steady state and fast transient heat flux information. Fabrication of the sensor does not require any matching of the mounting surface. Heat flux is proportional to the temperature difference across the upper and lower surfaces of an insulation material. The sensor consists of an array of thermocouples on the upper and lower surfaces of a thin insulating layer. The thermocouples for the sensor are connected in a thermopile arrangement. A 100 thermocouple pair heat flux sensor has been fabricated on silicon wafers. The sensor produced an output voltage of 200-400 microvolts when exposed to a hot air heat gun. A 20 element thermocouple pair heat flux sensor has been fabricated on aluminum oxide sheet. Thermocouples are Pt-Pt/Rh with silicon dioxide as the insulating material. This sensor produced an output of 28 microvolts when exposed to the radiation of a furnace operating at 1000 C. Work is also underway to put this type of heat flux sensor on metal surfaces.

Will, Herbert A.↗
NASA NTRS1992

The use of plasma ashers and Monte Carlo modeling for the projection of atomic oxygen durability of protected polymers in low Earth orbit

The results of ground laboratory and in-space exposure of polymeric materials to atomic oxygen has enabled the development of a Monte Carlo computational model which simulates the oxidation processes of both environments. The cost effective projection of long-term low-Earth-orbital durability of protected polymeric materials such as SiO(x)-coated polyimide Kapton photovoltaic array blankets will require ground-based testing to assure power system reliability. Although silicon dioxide thin film protective coatings can greatly extend the useful life of polymeric materials in ground-based testing, the projection of in-space durability based on these results can be made more reliable through the use of modeling which simulates the mechanistic properties of atomic oxygen interaction, and replicates test results in both environments. Techniques to project long-term performance of protected materials, such as the Space Station Freedom solar array blankets, are developed based on ground laboratory experiments, in-space experiments, and computational modeling.

Banks, Bruce A.↗
NASA NTRS1991

TRAC based sensing for autonomous rendezvous

The Targeting Reflective Alignment Concept (TRAC) sensor is to be used in an effort to support an Autonomous Rendezvous and Docking (AR&D) flight experiment. The TRAC sensor uses a fixed-focus, fixed-iris CCD camera and a target that is a combination of active and passive components. The system experiment is anticipated to fly in 1994 using two Commercial Experiment Transporters (COMET's). The requirements for the sensor are: bearing error less than or equal to 0.075 deg; bearing error rate less than 0.3 deg/sec; attitude error less than 0.5 deg.; and attitude rate error less than 2.0 deg/sec. The range requirement depends on the range and the range rate of the vehicle. The active component of the target is several 'kilo-bright' LED's that can emit 2500 millicandela with 40 milliwatts of input power. Flashing the lights in a known pattern eliminates background illumination. The system should be able to rendezvous from 300 meters all the way to capture. A question that arose during the presentation: What is the life time of the LED's and their sensitivity to radiation? The LED's should be manufactured to Military Specifications, coated with silicon dioxide, and all other space qualified precautions should be taken. The LED's will not be on all the time so they should easily last the two-year mission.

Everett, Louis J.↗
NASA NTRS1994

Cryogenic Gellant and Fuel Formulation for Metallized Gelled Propellants: Hydrocarbons and Hydrogen with Aluminum

An experimental program to determine the viability of nanoparticulate gellant materials for gelled hydrocarbons and gelled liquid hydrogen was conducted. The gellants included alkoxides (BTMSE and BTMSH) and silica-based materials. Hexane, ethane, propane and hydrogen were gelled with the newly-formulated materials and their rheological properties were determined: shear stress versus shear rate and their attendant viscosities. Metallized hexane with aluminum particles was also rheologically characterized. The propellant and gellant formulations were selected for the very high surface area and relatively-high energy content of the gellants. These new gellants can therefore improve rocket engine specific impulse over that obtained with traditional cryogenic-fuel gellant materials silicon dioxide, frozen methane, or frozen ethane particles. Significant reductions in the total mass of the gellant were enabled in the fuels. In gelled liquid hydrogen, the total mass of gellant was reduced from 10-40 wt percent of frozen hydrocarbon particles to less that 8 wt percent with the alkoxide.

Wong, Wing↗
NASA NTRS1996

Containerless Liquid-Phase Processing of Ceramic Materials

The present project builds on the results of research supported under a previous NASA grant to investigate containerless liquid-phase processing of molten ceramic materials. The research used an aero-acoustic levitator in combination with cw CO2 laser beam heating to achieve containerless melting, superheating, undercooling, and solidification of poorly-conducting solids and liquids. Experiments were performed on aluminum oxide, binary aluminum oxide-silicon dioxide materials, and oxide superconductors.

Weber, J. K. Richard↗
NASA NTRS1997

Metallized Gelled Propellants: Oxygen/RP-1/Aluminum Rocket Engine Calorimeter Heat Transfer Measurements and Analysis

A set of analyses was conducted to determine the heat transfer characteristics of metallized gelled liquid propellants in a rocket engine. The analyses used the data from experiments conducted with a small 30- to 40-lbf thrust engine composed of a modular injector, igniter, chamber and nozzle. The fuels used were traditional liquid RP-1 and gelled RP-1 with 0-wt %, 5-wt%, and 55-wt% loadings of aluminum with silicon dioxide gellant, and gaseous oxygen as the oxidizer. Heat transfer was computed based on measurements using calorimeter rocket chamber and nozzle hardware with a total of 31 cooling channels. A gelled fuel coating formed in the 0-, 5- and 55-wt% engines, and the coating was composed of unburned gelled fuel and partially combusted RP-1. The coating caused a large decrease in calorimeter engine heat flux in the last half of the chamber for the 0- and 5-wt% RP-1/Al. This heat flux reduction effect was analyzed by comparing engine runs and the changes in the heat flux during a run as well as from run to run. Heat transfer and time-dependent heat flux analyses and interpretations are provided. The 5- and 55-wt% RP-1/Al fueled engines had the highest chamber heat fluxes, with the 5-wt% fuel having the highest throat flux. This result is counter to the predicted result, where the 55 wt% fuel has the highest combustion and throat temperature, and therefore implies that it would deliver the highest throat heat flux. The 5-wt% RP-1/Al produced the most influence on the engine heat transfer and the heat flux reduction was caused by the formation of a gelled propellant layer in the chamber and nozzle.

Palaszewski, Bryan↗
NASA NTRS1994

Simulations of Terrestrial in-situ Cosmogenic-Nuclide Production

Targets of silicon and silicon dioxide were irradiated with spallation neutrons to simulate the production of long-lived radionuclides in the surface of the Earth. Gamma-ray spectroscopy was used to measure Be-7 and Na-22, and accelerator mass spectrometry was used to measure Be-10, C-14, and Al-26. The measured ratios of these nuclides are compared with calculated ratios and with ratios from other simulations and agree well with ratios inferred from terrestrial samples.

Reedy, R. C.↗