Search NASA⌕ Search

SEARCH · Search NASA

Results for “silicon solar cell”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Silicon solar cell efficiency - Practice and promise.

The maximum efficiency of silicon solar cells is calculated and yields a value near 18%. Additionally, the performance of these high efficiency cells in a synchronous orbit radiation field is calculated and indicates that these cells would be superior to present silicon cells at all times. The performance of conventional cells is analyzed and several areas in which performance gains may be achieved are discussed. These areas include improvements in diffused region profile, in reduction of excess forward currents in cells made from low resistivity material and in the theory for describing complex solar cell structures.

Brandhorst, H. W., Jr.↗
NASA NTRS1972

Silicon solar cell efficiency: Practice and promise

The maximum efficiency of silicon solar cells was calculated and yielded a value near 18%. Additionally, the performance of these high efficiency cells in a synchronous orbit radiation field was calculated and it is suggested that these cells would be superior to present silicon cells. The performance of conventional cells was analyzed and several areas in which performance gains may be achieved are discussed. These areas include improvements in diffused region profile, in reduction of excess forward currents in cells made from low resistivity material, and in the theory for describing complex solar cell structures.

Brandhorst, H. W., Jr.↗
NASA NTRS1975

Effects of high doping levels on silicon solar cell performance

Open-circuit voltages measured in silicon solar cells made from 0.01 ohm-cm material are 150 mV lower than voltages calculated from simple diffusion theory and cannot be explained by poor diffusion lengths or surface leakage currents. An analytical study was made to determine whether high doping effects, which increase the intrinsic carrier concentration, could account for the low observed voltages and to determine the limits on voltage and efficiency imposed by high doping effects. The results indicate that the observed variation of voltage with base resistivity is predicted by these effects. A maximum efficiency of 19% (AMO) and a voltage of 0.7 volts were calculated for 0.1 ohm-cm cells assuming an optimum diffused layer impurity profile.

Godlewski, M. P.↗
NASA NTRS1977

Performance limitations of silicon solar cells

This paper discusses the performance limitations of silicon solar cells which have been identified and investigated using a detailed numerical analysis of solar cell operation. Efficiency limitations are discussed as related to doping densities, minority carrier lifetimes, widths of solar cell regions, surface recombination, antireflecting layers, and ohmic contact stripes. Areas in which improvements can be expected in performance are identified and discussed.

Hauser, J. R.↗
NASA NTRS1985

Studies of the nature of interfacial barriers in high efficiency crystalline silicon solar cells

The effects of interfacial barriers in crystalline silicon solar cells were studied. The effort was directed toward the investigation and use of such techniques as Angular Resolved Parameter Spectroscopy (ARAPS) and Impedance Spectroscopy in initially characterizing n-type Si doped to levels commonly used for n+p solar cells, and eventually Si solar cells. The objectives of the research are given. Those accomplished are detailed, as are recommendations for future work.

Bates, Clayton W., Jr.↗
NASA NTRS1986

Development of flight ready fifty-micron-thick silicon solar cell array module technology

The development of ultrathin silicon solar cell array modules from initial design to flight testing is discussed. Three 80-cell modules were subjected to the thermal soak test, the LEO thermal cycle test, and the solar array flight experiment, and six 48-cell welded modules were evaluated in the geosynchronous orbit thermal cycle test. It is observed that the electrical performance of the modules was not affected by the different environmental conditions. The automatic assembly of the cell modules, in particular the welding and solar cell glassing operation, is described. The specific power capabilities of Kapton, Kapton-Kevlar-Kapton, Kapton-graphite-Kapton, and Kapton-graphite-aluminum honeycomb-graphite solar array designs are assessed.

Patterson, R. E.↗
NASA NTRS1986

High efficiency crystalline silicon solar cells

The factors which may limit current crystalline silicon solar cells to less than 20 percent efficiency at AM 1 are investigated together with the factors which may limit the ultimate efficiency achievable. It was found that base recombination at residual defect and impurity recombination centers was the likely cause of the 20-percent efficiency barrier. Suggestions for design changes that would cut the losses due to recombinations are presented.

Sah, C. T.↗
NASA NTRS1981

Silicon solar cells with nickel/solder metallization

The use of nickel plus solder is shown to be feasible for contact metallization for silicon solar cells by offering a relatively inexpensive method of making electrical contact with the cell surfaces. Nickel is plated on silicon solar cells using an electroless chemical deposition method to give contacts with good adhesion, and in some cases where adhesion is poor initially, sintering under relatively mild conditions will dramatically improve the quality of the bond without harming the p-n junction of the cell. The cells can survive terrestrial environment stresses, which is demonstrated by a 1000 hour test at 85 C and 85% relative humidity under constant forward bias of 0.45 volt.

Petersen, R. C.↗
DOE OSTI2024

Ultraviolet Laser Activation of Phosphorus-Doped Polysilicon Layers for Crystalline Silicon Solar Cells

In crystalline silicon photovoltaics (c-Si PV), a pulsed laser can be used as a substitute for a high-temperature furnace dopant diffusion/activation step. In contrast to furnace-based activation, lasers can be used to achieve highly localized doping with controlled dopant concentrations, useful in advanced architectures such as the interdigitated back contact (IBC) solar cell. In this study, a pulsed ultraviolet (UV) laser is utilized for phosphorus dopant activation within a low-pressure chemical vapor deposited (LPCVD) polycrystalline silicon (poly-Si) passivated contact layer. The highest implied open-circuit voltage iV oc values achieved using this approach reach 726 mV. However, this comes at the expense of high specific contact resistivities ρ c , which is attributed to a lower dopant concentration across the poly-Si(n + )/SiO x /c-Si interface. Regardless, the optimum iV oc , ρ c combination is measured at a laser fluence of 0.78 J cm -2 producing values of 712 mV and 89 mΩ-cm 2 , respectively. These values are still compatible with high-efficiency solar cell designs, underscoring the feasibility and effectiveness of this approach.

14 SOLAR ENERGY↗
NASA NTRS1980

Radiation tolerance of boron doped dendritic web silicon solar cells

The potential of dendritic web silicon for giving radiation hard solar cells is compared with the float zone silicon material. Solar cells with n(+)-p-P(+) structure and approximately 15% (AMl) efficiency were subjected to 1 MeV electron irradiation. Radiation tolerance of web cell efficiency was found to be at least as good as that of the float zone silicon cell. A study of the annealing behavior of radiation-induced defects via deep level transient spectroscopy revealed that E sub v + 0.31 eV defect, attributed to boron-oxygen-vacancy complex, is responsible for the reverse annealing of the irradiated cells in the temperature range of 150 to 350 C.

Rohatgi, A.↗
NASA NTRS1977

Developments in vertical-junction silicon solar cells

Non-reflective vertical junction silicon cells provide high conversion efficiency radiation-resistant solar cells. New techniques of oxidation growth and the use of photolithography enable the use of an orientation dependent etch producing grooves 5 to 10 microns wide over 100 microns deep. These silicon wafers are then processed into solar cells with all of the processes performed at temperatures compatible with producing high efficiency solar cells. Most of the photogenerated carriers are created in the walls where they are within a few microns of the collecting junction. Consequently, degradation of carrier diffusion length due to radiation has a considerably reduced effect on collection efficiency. These 2 cm x 2 cm vertical junction silicon solar cells have exceeded 13% AMO efficiency and have shown superior radiation resistance.

Lindmayer, J.↗