Search NASA⌕ Search

SEARCH · Search NASA

Results for “sintering temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS2007

A Symmetrical, Planar SOFC Design for NASA's High Specific Power Density Requirements

Solid oxide fuel cell (SOFC) systems for aircraft applications require an order of magnitude increase in specific power density (1.0 kW/kg) and long life. While significant research is underway to develop anode supported cells which operate at temperatures in the range of 650-800 C, concerns about Cr-contamination from the metal interconnect may drive the operating temperature down further, to 750 C and lower. Higher temperatures, 900-1000 C, are more favorable for SOFC stacks to achieve specific power densities of 1.0 kW/kg. Since metal interconnects are not practical at these high temperatures and can account for up to 75% of the weight of the stack, NASA is pursuing a design that uses a thin, LaCrO3-based ceramic interconnect that incorporates gas channels into the electrodes. The bi-electrode supported cell (BSC) uses porous YSZ scaffolds, on either side of a 10-20 microns electrolyte. The porous support regions are fabricated with graded porosity using the freeze-tape casting process which can be tailored for fuel and air flow. Removing gas channels from the interconnect simplifies the stack design and allows the ceramic interconnect to be kept thin, on the order of 50 -100 microns. The YSZ electrode scaffolds are infiltrated with active electrode materials following the high temperature sintering step. The NASA-BSC is symmetrical and CTE matched, providing balanced stresses and favorable mechanical properties for vibration and thermal cycling.

Cable, Thomas L.↗
NASA NTRS2016

Atmospheric Pressure Plasma Jet as a Dry Alternative to Inkjet Printing in Flexible Electronics

We have developed an atmospheric pressure plasma jet printing system that works at room temperature to 50 deg C unlike conventional aerosol assisted techniques which require a high temperature sintering step to obtain desired thin films. Multiple jets can be configured to increase throughput or to deposit multiple materials, and the jet(s) can be moved across large areas using a x-y stage. The plasma jet has been used to deposit carbon nanotubes, graphene, silver nanowires, copper nanoparticles and other materials on substrates such as paper, cotton, plastic and thin metal foils.

Printable electronics↗
NASA NTRS2017

Nuclear Rocket Ceramic Metal Fuel Fabrication Using Tungsten Powder Coating and Spark Plasma Sintering

Nuclear thermal propulsion is an enabling technology for crewed Mars missions. An investigation was conducted to evaluate spark plasma sintering (SPS) as a method to produce tungsten-depleted uranium dioxide (W-dUO2) fuel material when employing fuel particles that were tungsten powder coated. Ceramic metal fuel wafers were produced from a blend of W-60vol% dUO2 powder that was sintered via SPS. The maximum sintering temperatures were varied from 1,600 to 1,850 C while applying a 50-MPa axial load. Wafers exhibited high density (>95% of theoretical) and a uniform microstructure (fuel particles uniformly dispersed throughout tungsten matrix).

Barnes, M. W.↗
NASA NTRS2018

Physical and Biological Properties of Cobalt- and Copper-Doped Calcium Phosphates as Bone Substitute Materials

Arthritis, osteoporosis, and other bone diseases and defects are common medical issues worldwide. By utilizing ceramic biomaterials as bone substitutes to treat these diseases, bone regeneration can be promoted and toxicity from the substitute material can be limited. Calcium phosphate (CaP) ceramics have become popular as bone substitutes due to their biocompatibility and similarity in composition to natural bone. The purpose of this research was to investigate the physical properties and biological responses of CaP-based bone substitutes, doped with metal ions. Some metal ions are present in natural bone in small amounts, and recent studies show they affect the biological responses of CaPs significantly. Dopants such as magnesium (Mg), strontium (Sr), silicon (Si) and iron (Fe) alter the phase composition, mechanical properties, osteogenesis and angiogenesis properties of CaPs, depending on their concentration and method of addition. In the present study, the effects of cobalt (Co) and copper (Cu) on the physical and biological properties of two main CaP materials, brushite cement (BrC) and tricalcium phosphate (TCP), have been investigated. Different concentrations of dopants in forms of oxide and/or chloride were selected and their effect on phase composition, sintering behavior, density, setting time, compressive strength and in vitro interaction with osteosarcoma and osteoblast cells were studied. Different techniques of sample preparation, challenges during cement preparation and compact sample pressing, sintering, and methods of dopant addition are discussed. The presence of Cu in tricalcium phosphate was found to increase thermal stability of the material and decrease the impact of sintering temperature on porosity. In addition, Cu caused a reduction in expression of inflammatory gene markers by human osteoblast cells and an increased expression at early time points due of osteoinductive markers.The addition of Cu and Co to brushite cement caused an increase in thermal stability of the material, and the addition of Cu caused significant increase in setting time. Small dopant amounts of Co caused decrease in setting time, but higher amounts caused an increase. In addition, Cu dopant in small amounts resulted in an increase of compressive strength. Both Cu and Co led to a decrease in expression of inflammatory gene markers by osteoblast and osteosarcoma cells respectively, and Cu also caused an increase in osteoinductive marker expression. Thus, these results indicate that Cu and Co have a positive impact on the physical, mechanical and biological properties of calcium phosphate biomaterials.

Cummings, Haley V.↗
NASA NTRSDate not supplied

Additive Manufacturing and Working Fluid Characterization of Ceramic Heat Pipes

In this work, additively manufactured (AM) aluminum nitride (AlN) ceramic heat pipes were developed to improve spacecraft heat rejection capabilities beyond the current state-of-the-art metal systems. A low sintering temperature aluminum nitride slurry is developed for digital light processing printing (DLP) and the optimal debinding curves are examined. Printed AlN parts are characterized via SEM and optical profilometry. AlN 3D-printed parts are also tested for compatibility with aluminum bromide, aluminum chloride, and iodine, among other proposed working fluids at 350-600 K in an inert atmosphere, with reactivity measured via SEM and Fourier transform infrared spectroscopy (FTIR).

Thermal Management↗
DOE OSTI2020

Mn-doped oxide nuclear fuel

A nuclear fuel includes uranium(IV) oxide (UO2) and manganese (Mn) as a dopant. The Mn dopant may be present in the fuel in an amount up to the solubility limit for Mn under a given set of conditions, for example, about 0.01 wt % to about 1 wt %. The nuclear fuel is substantially free of aluminum (Al). The nuclear fuel exhibits enhanced grain size development during sintering temperatures as low at 1400 K due to an increase in uranium sub-lattice vacancies induced by dissolution of the Mn dopant at interstitial defect sites. The Mn-doped nuclear fuel exhibits improved grain sizes at lower temperatures compared to Cr-, Al-, and undoped UO2, and therefore desirably exhibits lower fission gas release and higher plasticity, reducing the chances of fuel rod failure.

Cooper, Michael William Donald↗
DOE OSTI2022

Low-temperature selective laser sintering 3D printing of PEEK-Nylon blends: Impact of thermal post-processing on mechanical properties and thermal stability

Herein, a high-performance polymer (HPP) (polyether ether ketone, PEEK) blended with a commercial low-temperature polymer (polyamide 12, PA-12) was fabricated using a low-temperature selective laser sintering (SLS) 3D printer. Different post-processing heat treatments were implemented after fabrication to tune the thermal and mechanical properties of printed blends. The specific mechanical modulus of the blend was increased up to 79% in comparison to printed PA-12 samples with heat treatment. Additionally, the thermal resistance of the treated blends greatly exceeded the properties observed using PA-12 alone. This research proposes a methodology to fabricate and engineer HPP using desktop SLS printers through a secondary lower melting temperature material and heat treatments.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

Metal Fused Filament Fabrication of Titanium Alloy for In Space Manufacturing

NASA is developing materials and processes for the in-space manufacturing of many items for the International Space Station (ISS) and future exploration platforms. These new manufacturing processes will require the further development of current 3D printing processes to achieve high-performance metal parts within the power and space constraints of the ISS. Manufacturing Ti-6Al-4V alloy parts with 3D printing using a metal fused filament fabrication (MF3) process is an alternative process to the Direct Metal Laser Sintering (DMLS) of the metal powders additive manufacturing process. Our initial work fabricating Ti-6Al-4V parts from Ti-6Al-4V powder-binder feedstock and processed with the MF3 process has resulted in 95-97% sintered densities. The current development work of optimized sintered properties investigates the effects of variation in sintering time, temperature, and vacuum on the sintered properties of Ti-6Al-4V MF3 printed tensile bars. Sintered properties such as density, hardness, and tensile properties were characterized followed by microstructural and chemical (O/C/N) analysis to understand the role of sintering process on the ensuing material properties. Future development of the MF3 process will also involve investigation of the effects of micro-milling the Ti-64Al-4V powder to nanometer particle sizes and the investigation of laser sintering of the 3D printed devices. This new micro-milling technique will have broad application to other areas that require particle size reduction of hard metallic materials, such as Nuclear Thermal Propulsion and other NASA technologies. Laser sintering in lieu of high temperature thermal sintering should allow for significant power reduction and improved processing speeds.

sintering, alloys, 3D printing↗
DOE OSTI2023

Shrinkage, microstructure, and mechanical properties of sintered 3D-printed silica via stereolithography

Stereolithography has been used to create ceramic parts with complex geometry that is difficult to achieve with conventional fabrication techniques. Here this study used stereolithography to print silica honeycomb structures with a commercial Formlabs Form2 printer. The printed samples were sintered at different temperatures, and the print shape was retained up to 1300°C, but significant distortion from partial melting occurred at 1400°C. Higher sintering temperatures lead to more shrinkage, but it is non-uniform among directions, with the open cell plane shrinking more than the dense plane of the sample. As expected, the density of samples also increases with the sintering temperature. At higher sintering temperatures, there is an increase in cristobalite and a decrease in quartz, tridymite, and amorphous silica. Regarding mechanical properties, the out-of-plane compressive strength is approximately one order of magnitude higher than the in-plane compressive strength. When compressed along the out-of-plane direction, the samples sintered at lower temperatures surprisingly exhibit higher strength, which is explained by the micro-cracking mechanism. As expected, the samples sintered at higher temperatures display higher strength when compressed along the in-plane direction.

36 MATERIALS SCIENCE↗
NASA NTRS1997

High performance thermoelectric materials and methods of preparation

Transition metals (T) of Group VIII (Co, Rh and Ir) have been prepared as semiconductor alloys with Sb having the general formula TSb.sub.3. The skutterudite-type crystal lattice structure of these semiconductor alloys and their enhanced thermoelectric properties results in semiconductor materials which may be used in the fabrication of thermoelectric elements to substantially improve the efficiency of the resulting thermoelectric device. Semiconductor alloys having the desired skutterudite-type crystal lattice structure may be prepared in accordance with the present invention by using vertical gradient freeze techniques, liquid-solid phase sintering techniques, low temperature powder sintering and/or hot-pressing. Measurements of electrical and thermal transport properties of selected semiconductor materials prepared in accordance with the present invention, demonstrated high Hall mobilities (up to 8000 cm.sup.2.V.sup.-1.s.sup.-1), good Seebeck coefficients (up to 400 .mu.VK.sup.-1 between 300.degree. C. and 700.degree. C.), and low thermal conductivities (as low as 15 mW/cmK). Optimizing the transport properties of semiconductor materials prepared from elemental mixtures Co, Rh, Ir and Sb resulted in a two fold increase in the thermoelectric figure of merit (ZT) at temperatures as high as 400.degree. C. for thermoelectric elements fabricated from such semiconductor materials.

Fleurial, Jean-Pierre↗
DOE OSTI2024

Ink Casting and 3D‐Extrusion Printing of Yb 14 MnSb 11 for High‐Temperature Thermoelectric Material

Abstract Complex shapes are created from Yb 14 MnSb 11 , a high‐temperature thermoelectric Zintl phase, via a two‐step process: i) layer‐by‐layer 3D‐extrusion of ink containing partially‐reacted powders which are ball‐milled from a blend of Yb, MnSb, and Sb powders; ii) heat treatment to synthesize the ternary compound Yb 14 MnSb 11 and densify the extruded powders. A high phase purity for Yb 14 MnSb 11 (83–94%) is achieved in both cast and 3D‐extruded ink specimens via a solid‐state reaction between Yb, MnSb, and Yb 4 Sb 3 during reactive sintering. Pressure‐free sintering at temperatures of 1200–1400 °C densifies the powders to 82% relative density but can also induce the decomposition of the Yb 14 MnSb 11 phase due to Yb sublimation. A process window with optimized sintering temperature and time is identified, achieving both low porosity and high phase purity and reaching a maximum zT = 0.61 at 1000 °C, about half of the maximum zT value for bulk Yb 14 MnSb 11 made via conventional processes (pressure sintering of precursor powders). The present approach – direct ink writing of ball‐milled powders, combined with reactive sintering – is a scalable and affordable method to fabricate thermoelectric legs with intricate 3D shapes, for enhanced performances in high‐temperature thermoelectric applications.

Chen, Ming [Department of Materials Science &amp, ↗
NASA NTRS2013

Three-Dimensional (3D) Additive Construction: Printing with Regolith

Three dimensional (3D) printing is a new and booming topic in many realms of research and engineering technology. When it comes to space science and aerospace engineering, it can be useful in numerous ways. As humans travel deeper into space and farther from Earth, sending large quantities of needed supplies from Earth for a mission becomes astronomically expensive and less plausible. In order to reach further to new places, In Situ Resource Utilization (ISRU), a project that pushes for technologies to use materials already present in the destination's environment, is necessary. By using materials already available in space such as regolith from the Moon, Mars, or an asteroid's surface, fewer materials need to be brought into space on a launched vehicle. This allows a vehicle to be filled with more necessary supplies for a deep space mission that may not be found in space, like food and fuel. This project's main objective was to develop a 3D printer that uses regolith to "print" large structures, such as a dome, to be used as a heat shield upon a vehicle's reentry into the atmosphere or even a habitat. 3D printing is a growing technology that uses many different methods to mix, heat, and mold a material into a specific shape. In order to heat the regolith enough to stick together into a solid shape, it must be sintered at each layer of material that is laid. Sintering is a process that heats and compresses a powdered material until it fuses into a solid, which requires a lot of energy input. As an alternative, a polymer can be mixed with the regolith before or as it is sent to the 3D printer head to be placed in the specific shape. The addition of the polymer, which melts and binds at much lower temperatures than sintering temperatures, greatly decreases the required heating temperature and energy input. The main task of the project was to identify a functional material for the printer. The first step was to find a miscible. polymer/solvent solution. This solution was added to the regolith and the solvent was evaporated essentially leaving polymer-coated regolith particles. This material would be sent through the printer head and heated layer by layer to melt the polymer and bind the regolith. This method was one of many in a large goal to utilize materials in space with a custom-made 3D printer that builds dome-shaped habitats and other essential equipment for future deep space missions.

Tsoras, Alexandra↗
DOE OSTI2025

Tuning transition metal nanoparticles on a non-traditional support via experimental design

The ability to control metal nanoparticle size and morphology on supported catalysts is crucial for optimizing catalytic performance in targeted applications. Here, this work presents a systematic approach for tuning Ni particle and crystallite size on an unconventional, low-porosity silica fume support through select thermal treatments. The catalyst was synthesized via the deposition of nickelocene onto silica fume, resulting in well-dispersed Ni nanoparticles. A face-centered central composite design was employed to systematically assess the effects of time, temperature, and sintering gas environment on metal particle growth. The results demonstrate that the sintering gas environment is the primary factor governing particle and crystallite evolution, with temperature as the next most significant influence. Nickel nanoparticles sintered at temperatures of 650 °C and above under inert conditions exhibited substantial growth and polycrystalline structures, whereas samples treated in oxidative environments formed NiO, restricting particle mobility. Minimally oxidative (500 ppm O₂) environments facilitated rapid sintering while effectively removing residual ligands from the one-step nickelocene deposition process. Extensive structural characterization via a combination of scanning transmission electron microscopy, X-ray diffraction, hydrogen temperature programmed reduction, and small-angle X-ray scattering revealed that oxidative treatments enhanced metal-support interactions, as evidenced by increased reduction temperatures and narrower particle size distributions. These findings establish quantitative relationships between sintering parameters and Ni nanoparticle characteristics, providing a framework for rational catalyst design through controlled thermal treatments. This methodology is broadly applicable to other catalytic systems and provides a quantitative foundation for catalyst design.

CVD↗
NASA NTRS1985

Tensile test of pressureless-sintered silicon nitride at elevated temperature

Uniaxial tensile strength tests of pressureless sintered silicon nitride were carried out in air at temperatures ranging from room temperature up to 1600 C. Silicon nitrides containing Y2O3, Al2O3, Al2O3-MgO, or MgO-CeO2 additives were tested. The results show that the composition of the additive used influences the strength characteristics of the silicon nitride. The tensile strength rapidly decreased at temperatures above 1000 C for the materials containing MgO as the additive and above 1000 C for the material with Y2O3. When the temperature increased to as high as 1300 C, the strength decreased to about 10 percent of the room temperature strength in each case. Observations of the fracture origin and of the crack propagation on the fracture surfaces are discussed.

Matsusue, K.↗
DOE OSTI2026

Hybrid Additive Manufacturing and Electric Field-Assisted Sintering of High-temperature Heat Exchangers via Sacrificial Channel Molds

A hybrid manufacturing approach, integrating additive manufacturing (AM) with powder methodology via electric field-assisted sintering (EFAS), was developed for the fabrication of high-temperature compact heat exchangers (CHX) from refractory metals. The methodology employed additively manufactured sacrificial channel molds (SCMs) as shapeholders for CHX channels, which were embedded in metal powders using EFAS. Following embedding, the SCMs were chemically dissolved to form the internal channel network. SCMs were fabricated using both digital light processing (DLP) and direct ink writing (DIW) from chemically reactive, calcium-based ceramic feedstocks with varying ratios of Al2O3 reinforcement. The microstructure, phase composition, and dissolution behavior of both as-printed and embedded SCMs were investigated. The shrinkage behavior of the SCMs embedded in refractory metals, as well as the interfacial characteristics between the SCMs and metal matrix, were studied. The results showed that the SCMs containing sufficient chemical reactive ceramics dissolved effectively before and after embedding. The as-printed SCMs retained the phase composition of their feedstocks, but the embedded SCMs containing calcium-based ceramics and Al2O3 exhibited the formation of calcium aluminates due to high temperature exposure during embedding. Most SCMs exhibited a cellular Al2O3 network filled with Ca-rich ceramics. Shrinkage after embedding was strongly dependent on SCM density, with lower density SCMs exhibiting greater shrinkage. A thin SCM-affected zone was observed at the metal matrix surface, characterized by increased porosity compared to the bulk matrix. This effect was attributed to infiltration of the SCM materials into powder particle boundaries under pressure, followed by their removal during dissolution. This study demonstrates the feasibility of manufacturing CHXs from hard-to-process refractory metals for use in harsh environments.

36 - MATERIALS SCIENCE↗