Search NASA⌕ Search

SEARCH · Search NASA

Results for “software size”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

GlennICE Simulation of 24, 28 and 36 Inch Diameter eVTOL Propellers in Forward Flight

Flow solutions and water collection results are presented for three different propeller sizes. Flow solutions were generated using the NASA FUN3D software, and water collection was simulated using NASA GlennICE software. The geometries considered represent experimental articles that have been tested in the NASA Icing Research Tunnel. Each configuration has four blades. For the experiment, the same spinner centerbody is used for each propeller size. The different sized blades are similar for radii larger than about 40% of total span. Operating conditions were chosen to match operating points where experimental data was collected. Results are presented for both single bin simulations, as well as 7-bin Langmuir D distributions. For 80 microns MVD the Langmuir D distribution showed small differences compared to the single bin. For 15 microns MVD the Langmuir D distribution had a larger impact, especially on the spinner. In the experiment, the centerbody was unchanged as propeller size was changed. In this paper, additional simulations were completed with the 36 inch case perfectly scaled down to 24 and 28 inch. The perfect geometric scaling allows for an assessment of the effect of constant centerbody size on the results. While slight differences in pressure distribution on the propeller are visible between scaled and non-scaled centerbody, the effect seems quite minimal regarding water collection. All simulations were run very cold to ensure rime ice, since handling runback water in the non-inertial frame is beyond the scope of the present work. Ice shapes were generated using a single time step growth. The total mass on the blade and spinner was generally underpredicted for 15 microns MVD, and overpredicted for 80 microns MVD. When comparing ice shapes at operating conditions the numerical results produce very similar ice shapes.

Aircraft Icing↗
NASA NTRSDate not supplied

GlennICE Simulation of 24, 28 and 36 Inch Diameter eVTOL Propellers in Forward Flight

Flow solutions and water collection results are presented for three different propeller sizes. Flow solutions were generated using the NASA FUN3D software, and water collection was simulated using NASA GlennICE software. The geometries considered represent experimental articles that have been tested in the NASA Icing Research Tunnel. Each configuration has four blades. For the experiment, the same spinner centerbody is used for each propeller size. The different sized blades are similar for radii larger than about 40% of total span. Operating conditions were chosen to match operating points where experimental data was collected. Results are presented for both single bin simulations, as well as 7-bin Langmuir D distributions. For 80 microns MVD the Langmuir D distribution showed small differences compared to the single bin. For 15 microns MVD the Langmuir D distribution had a larger impact, especially on the spinner. In the experiment, the centerbody was unchanged as propeller size was changed. In this paper, additional simulations were completed with the 36 inch case perfectly scaled down to 24 and 28 inch. The perfect geometric scaling allows for an assessment of the effect of constant centerbody size on the results. While slight differences in pressure distribution on the propeller are visible between scaled and non-scaled centerbody, the effect seems quite minimal regarding water collection. All simulations were run very cold to ensure rime ice, since handling runback water in the non-inertial frame is beyond the scope of the present work. Ice shapes were generated using a single time step growth. The total mass on the blade and spinner was generally underpredicted for 15 microns MVD, and overpredicted for 80 microns MVD. When comparing ice shapes at operating conditions the numerical results produce very similar ice shapes.

Aircraft Icing↗
NASA NTRS1994

Development of a nondestructive vibration technique for bond assessment of Space Shuttle tiles

This final report describes the achievements of the above titled project. The project is funded by NASA-KSC (Grant No. NAG 10-0117) for the period of 1 Jan. to 31 Dec. 1993. The purpose of this project was to develop a nondestructive, noncontact technique based on 'vibration signature' of tile systems to quantify the bond conditions of the thermal protection system) tiles of Space Shuttle orbiters. The technique uses a laser rapid scan system, modal measurements, and finite element modeling. Finite element models were developed for tiles bonded to both clamped and deformable integrated skin-stringer orbiter mid-fuselage. Results showed that the size and location of a disbonded tile can be determined from frequency and mode shape information. Moreover, a frequency response survey was used to quickly identify the disbonded tiles. The finite element results were compared with experimentally determined frequency responses of a 17-tile test panel, where a rapidscan laser system was employed. An excellent degree of correlation between the mathematical simulation and experimental results was realized. An inverse solution for single-tile assemblies was also derived and is being implemented into a computer program that can interact with the modal testing software. The output of the program displays the size and location of disbond. This program has been tested with simulated input (i.e., finite element data), and excellent agreement between predicted and simulated disbonds was shown. Finally, laser vibration imaging and acoustic emission techniques were shown to be well suited for detecting and monitoring the progressive damage in Graphite/Epoxy composite materials.

Moslehy, Faissal A.↗
NASA NTRS1998

The Dependence of Signal-To-Noise Ratio (S/N) Between Star Brightness and Background on the Filter Used in Images Taken by the Vulcan Photometric Planet Search Camera

The Vulcan Photometric Planet Search is the ground-based counterpart of Kepler Mission Proposal. The Kepler Proposal calls for the launch of telescope to look intently at a small patch of sky for four year. The mission is designed to look for extra-solar planets that transit sun-like stars. The Kepler Mission should be able to detect Earth-size planets. This goal requires an instrument and software capable of detecting photometric changes of several parts per hundred thousand in the flux of a star. The goal also requires the continuous monitoring of about a hundred thousand stars. The Kepler Mission is a NASA Discovery Class proposal similar in cost to the Lunar Prospector. The Vulcan Search is also a NASA project but based at Lick Observatory. A small wide-field telescope monitors various star fields successively during the year. Dozens of images, each containing tens of thousands of stars, are taken any night that weather permits. The images are then monitored for photometric changes of the order of one part in a thousand. These changes would reveal the transit of an inner-orbit Jupiter-size planet similar to those discovered recently in spectroscopic searches. In order to achieve a one part in one thousand photometric precision even the choice of a filter used in taking an exposure can be critical. The ultimate purpose of an filter is to increase the signal-to-noise ratio (S/N) of one's observation. Ideally, filters reduce the sky glow cause by street lights and, thereby, make the star images more distinct. The higher the S/N, the higher is the chance to observe a transit signal that indicates the presence of a new planet. It is, therefore, important to select the filter that maximizes the S/N.

Mena-Werth, Jose↗
NASA NTRS2012

Science Benefits of Onboard Spacecraft Navigation

Primitive bodies (asteroids and comets), which have remained relatively unaltered since their formation, are important targets for scientific missions that seek to understand the evolution of the solar system. Often the first step is to fly by these bodies with robotic spacecraft. The key to maximizing data returns from these flybys is to determine the spacecraft trajectory relative to the target body-in short, navigate the spacecraft- with sufficient accuracy so that the target is guaranteed to be in the instruments' field of view. The most powerful navigation data in these scenarios are images taken by the spacecraft of the target against a known star field (onboard astrometry). Traditionally, the relative trajectory of the spacecraft must be estimated hours to days in advance using images collected by the spacecraft. This is because of (1)!the long round-trip light times between the spacecraft and the Earth and (2)!the time needed to downlink and process navigation data on the ground, make decisions based on the result, and build and uplink instrument pointing sequences from the results. The light time and processing time compromise navigation accuracy considerably, because there is not enough time to use more accurate data collected closer to the target-such data are more accurate because the angular capability of the onboard astrometry is essentially constant as the distance to the target decreases, resulting in better "plane-of- sky" knowledge of the target. Excellent examples of these timing limitations are high-speed comet encounters. Comets are difficult to observe up close; their orbits often limit scientists to brief, rapid flybys, and their coma further restricts viewers from seeing the nucleus in any detail, unless they can view the nucleus at close range. Comet nuclei details are typically discernable for much shorter durations than the roundtrip light time to Earth, so robotic spacecraft must be able to perform onboard navigation. This onboard navigation can be accomplished through a self- contained system that by eliminating light time restrictions dramatically improves the relative trajectory knowledge and control and subsequently increases the amount of quality data collected. Flybys are one-time events, so the system's underlying algorithms and software must be extremely robust. The autonomous software must also be able to cope with the unknown size, shape, and orientation of the previously unseen comet nucleus. Furthermore, algorithms must be reliable in the presence of imperfections and/or damage to onboard cameras accrued after many years of deep-space operations. The AutoNav operational flight software packages, developed by scientists at the Jet Propulsion Laboratory (JPL) under contract with NASA, meet all these requirements. They have been directly responsible for the successful encounters on all of NASA's close-up comet-imaging missions (see Figure !1). AutoNav is the only system to date that has autonomously tracked comet nuclei during encounters and performed autonomous interplanetary navigation. AutoNav has enabled five cometary flyby missions (Table!1) residing on four NASA spacecraft provided by three different spacecraft builders. Using this software, missions were able to process a combined total of nearly 1000 images previously unseen by humans. By eliminating the need to navigate spacecraft from Earth, the accuracy gained by AutoNav during flybys compared to ground-based navigation is about 1!order of magnitude in targeting and 2!orders of magnitude in time of flight. These benefits ensure that pointing errors do not compromise data gathered during flybys. In addition, these benefits can be applied to flybys of other solar system objects, flybys at much slower relative velocities, mosaic imaging campaigns, and other proximity activities (e.g., orbiting, hovering, and descent/ascent).

Autonomy↗
DOE OSTI2024

Neural Networks for Prediction of Complex Chemistry in Water Treatment Process Optimization

Water chemistry plays a critical role in the design and operation of water treatment processes. Detailed chemistry modeling tools use a combination of advanced thermodynamic models and extensive databases to predict phase equilibria and reaction phenomena. The complexity and formulation of these models preclude their direct integration in equation-oriented modeling platforms, making it difficult to use their capabilities for rigorous water treatment process optimization. Neural networks (NN) can provide a pathway for integrating the predictive capability of chemistry software into equation-oriented models and enable optimization of complex water treatment processes across a broad range of conditions and process designs. Herein, we assess how NN architecture and training data impact their accuracy and use in equation-oriented water treatment models. We generate training data using PhreeqC software and determine how data generation and sample size impact the accuracy of trained NNs. The effect of NN architecture on optimization is evaluated by optimizing hypothetical black-box desalination processes using a range of feed compositions from USGS brackish water data set, tracking the number of successful optimizations, and testing the impact of initial guess on the final solution. Our results clearly demonstrate that data generation and architecture impact NN accuracy and viability for use in equation-oriented optimization problems.

Dudchenko, Alexander V↗
NASA NTRS1980

Integrated analysis capability for large space systems

The development of an integrated analysis computer program capable of performing the conceptual/preliminary structural system design analysis of large space systems is addressed. The integrated analysis capability (IAC) specifications include thermal/structural/controls integration, an emphasis on existing software and interactive graphics and I/O, a project size capability of 1 to 50 users (1 to 5 users concurrent), and the use of the FORTRAN '77 language. The advantages of the DISCOS and NASTRAN computer programs to the IAC are outlined and recommendations for other programs are made. Barriers to the development of the system arising from the interdisciplinary data flow are defined.

Vos, R. G.↗
NASA NTRS1982

Combining analysis with optimization at Langley Research Center - An evolutionary process

Analytical and computational advances, at Langely Research Center (La RC), contributing to the evolution of computer programs combining analysis and optimization are presented, namely, strength sizing, concurrent strength and flutter sizing, and general optimization. Current work on a software system which executes the analysis and optimization in a sequential rather than concurrent mode is then described, as a step toward the long-term goal at La RC of developing the methodology for such systems. The software system is designated Enginering Analysis Language (EAL)/Programming Structural Synthesis System (PR)SSS), and work is being done on the incorporation of PROSSS into EAL. EAL language can perform most FORTRAN operations, including testing, branching, and looping, and its data base system can easily be accessed by any processor using FORTRAN callable utility subroutines. Some numerical results showing the accuracy of EAL/PROSSS are given.

Rogers, J. L., Jr.↗
NASA NTRS1992

Results of a low power ice protection system test and a new method of imaging data analysis

Tests were conducted on a BF Goodrich De-Icing System's Pneumatic Impulse Ice Protection (PIIP) system in the NASA Lewis Icing Research Tunnel (IRT). Characterization studies were done on shed ice particle size by changing the input pressure and cycling time of the PIIP de-icer. The shed ice particle size was quantified using a newly developed image software package. The tests were conducted on a 1.83 m (6 ft) span, 0.53 m (221 in) chord NACA 0012 airfoil operated at a 4 degree angle of attack. The IRT test conditions were a -6.7 C (20 F) glaze ice, and a -20 C (-4 F) rime ice. The ice shedding events were recorded with a high speed video system. A detailed description of the image processing package and the results generated from this analytical tool are presented.

Shin, Jaiwon↗
NASA NTRS1993

Probe For Measuring Dynamic Gas Temperature In Reversing Flows

In proposed technique for determining time-varying temperature of flowing gas, raw measurements of three thermocouples of different sizes processed by relatively simple data-reduction software. Three-thermocouple technique overcomes limitation of single-thermocouple technique.

Fralick, Gustave C.↗
NASA NTRS1992

Results of a low power ice protection system test and a new method of imaging data analysis

Tests were conducted on a BF Goodrich De-Icing System's Pneumatic Impulse Ice Protection (PIIP) system in the NASA Lewis Icing Research Tunnel (IRT). Characterization studies were done on shed ice particle size by changing the input pressure and cycling time of the PIIP de-icer. The shed ice particle size was quantified using a newly developed image software package. The tests were conducted on a 1.83 m (6 ft) span, 0.53 m (221 in) chord NACA 0012 airfoil operated at a 4 degree angle of attack. The IRT test conditions were a -6.7 C (20 F) glaze ice, and a -20 C (-4 F) rime ice. The ice shedding events were recorded with a high speed video system. A detailed description of the image processing package and the results generated from this analytical tool are presented.

Shin, Jaiwon↗
NASA NTRS2002

Mosad and Stream Vision For A Telerobotic, Flying Camera System

Two full custom camera systems using the Multiplexed OverSample Analog to Digital (MOSAD) conversion technology for visible light sensing were built and demonstrated. They include a photo gate sensor and a photo diode sensor. The system includes the camera assembly, driver interface assembly, a frame stabler board with integrated decimeter and Windows 2000 compatible software for real time image display. An array size of 320X240 with 16 micron pixel pitch was developed for compatibility with 0.3 inch CCTV optics. With 1.2 micron technology, a 73% fill factor was achieved. Noise measurements indicated 9 to 11 bits operating with 13.7 bits best case. Power measured under 10 milliwatts at 400 samples per second. Nonuniformity variation was below noise floor. Pictures were taken with different cameras during the characterization study to demonstrate the operable range. The successful conclusion of this program demonstrates the utility of the MOSAD for NASA missions, providing superior performance over CMOS and lower cost and power consumption over CCD. The MOSAD approach also provides a path to radiation hardening for space based applications.

Mandl, William↗
NASA NTRS2017

Optimizing Probability of Detection Point Estimate Demonstration

Probability of detection (POD) analysis is used in assessing reliably detectable flaw size in nondestructive evaluation (NDE). MIL-HDBK-18231and associated mh18232POD software gives most common methods of POD analysis. Real flaws such as cracks and crack-like flaws are desired to be detected using these NDE methods. A reliably detectable crack size is required for safe life analysis of fracture critical parts. The paper provides discussion on optimizing probability of detection (POD) demonstration experiments using Point Estimate Method. POD Point estimate method is used by NASA for qualifying special NDE procedures. The point estimate method uses binomial distribution for probability density. Normally, a set of 29 flaws of same size within some tolerance are used in the demonstration. The optimization is performed to provide acceptable value for probability of passing demonstration (PPD) and achieving acceptable value for probability of false (POF) calls while keeping the flaw sizes in the set as small as possible.

Koshti, Ajay M.↗
NASA NTRS2005

NASA Tech Briefs, September 2005

Topivs include: Diamond-Coated Carbon Nanotubes for Efficient Field Emission; Improved Anode Coatings for Direct Methanol Fuel Cells; Advanced Ablative Insulators and Methods of Making Them; PETIs as High-Temperature Resin-Transfer-Molding Materials; Stable Polyimides for Terrestrial and Space Uses; Low-Density, Aerogel-Filled Thermal-Insulation Tiles; High-Performance Polymers Having Low Melt Viscosities; Nonflammable, Hydrophobic Aerogel Composites for Insulation; Front-Side Microstrip Line Feeding a Raised Antenna Patch; Medium-Frequency Pseudonoise Georadar; Facilitating Navigation Through Large Archives; Program for Weibull Analysis of Fatigue Data; Comprehensive Micromechanics-Analysis Code - Version 4.0; Component-Based Visualization System; Software for Engineering Simulations of a Spacecraft; LabVIEW Interface for PCI-SpaceWire Interface Card; Path Following with Slip Compensation for a Mars Rover; International Space Station Electric Power System Performance Code-SPACE; Software for Automation of Real-Time Agents, Version 2; Software for Optimizing Plans Involving Interdependent Goals; Computing Gravitational Fields of Finite-Sized Bodies; Custom Sky-Image Mosaics from NASA's Information Power Grid; ANTLR Tree Grammar Generator and Extensions; Generic Kalman Filter Software; Alignment Stage for a Cryogenic Dilatometer; Rugged Iris Mechanism; Treatments To Produce Stabilized Aluminum Mirrors for Cryogenic Uses; Making AlNx Tunnel Barriers Using a Low-Energy Nitrogen-Ion Beam; Making Wide-IF SIS Mixers with Suspended Metal-Beam Leads; Sol-Gel Glass Holographic Light-Shaping Diffusers; Automated Counting of Particles To Quantify Cleanliness; Phase Correction for GPS Antenna with Nonunique Phase Center; Compact Infrasonic Windscreen; Broadband External-Cavity Diode Laser; High-Efficiency Solar Cells Using Photonic-Bandgap Materials; Generating Solid Models from Topographical Data; Computationally Lightweight Air-Traffic-Control Simulation; Spool Valve for Switching Air Flows Between Two Beds; Partial Model of Insulator/ Insulator Contact Charging; Asymmetric Electrostatic Radiation Shielding for Spacecraft; and Reusable Hybrid Propellant Modules for Outer-Space Transport.

Source record↗
NASA NTRS2019

Flexible Modem Interface (FMI) in Space - Extending Standardized Commercial Satellite Communications Services to Space Users

Recent innovations are producing a multitude of advanced commercial satellite communications (COMSATCOM) systems that could deliver massive amounts of SATCOM capacity at a fraction of current cost while also offering reliability and availability that is critical to achieving mission success for orbiting assets. Recognizing the alignment of commercial capabilities with the National Aeronautics and Space Administration's (NASA) diverse mission requirements, the agency is proactively engaging industry to formulate strategies leading towards a NASA communications architecture that includes advanced commercial capabilities. To fully leverage the expanded space resources, NASA must also address the integration of commercial waveforms into its space terminals. In pursuit of similar goals, the United States Department of Defense (DoD) is leading the standardization of the flexible modem interface (FMI) to address service integration for their tactical terminals in pursuit of a DoD Wideband SATCOM Enterprise.This paper describes how NASA is adapting this FMI standard to work with the Space Telecommunications Radio System (STRS) software-defined radio (SDR) framework to address the challenging size, weight, and power resource requirements for terminals in space. A full adaptation would include waveform compatibility with modular baseband processing, frequency compatibility with a wideband front end, and radiated beam control with an electronically steerable antenna to enable multi-provider commercial service capability in a feasible package for space terminals. Security is also a key aspect to be addressed for this integration since data will flow through commercial networks, commercial service providers have their own security mechanisms, and space terminals must be able to securely load proprietary software and firmware needed to access the commercial networks on demand. Success of this effort means commercial partners will be able to allow network-compliant implementations to be hosted on STRS-compliant SDRs in space for reliable and capable network access.

COMSATCOM↗
NASA NTRS2018

Rapid Model Import Tool (RMIT)

Our project is about developing a tool to implement conversion of 3D Computer Aided Design (CAD) models produced with software such as Delmia, 3DS Max, or Maya, into a size and format compatible with the Unity 3D environment. RMIT will be used to aid KSC engineering personnel in the design, development, testing, operations, and training on spacecraft, launch vehicles, facilities, and ground support equipment. For our project, we are using Blender, a free/open-source 3D graphics software, with the goal of developing, testing, and deploying a 3D CAD model converter tool. I worked on using Blender to import 3D CAD models exported from CATIA software into Collada file format. The Collada file format has file extension DAE. Importing the Collada DAE file as is into Blender, generates dots and dashes. In 3DS Max, there is an existing OpenCollada plugin and with that plugin, 3DS Max can import the DAE file successfully. But, Blender does not seem to have an OpenCollada plugin, so I worked on writing a new OpenCollada plugin for Blender. Since 3DS Max was able to display the image, I looked into comparing differences between the original DAE file and the DAE file exported from 3DS Max using the OpenCollada plugin. As Collada documents describing digital assets are XML files with file extension DAE, Collada files contains XML tags, making them easily modifiable. After some research, it appears that Blender does not like primitive 2D tags like tristrips and trifans. Changing those tags to polygons slightly improved the image, but the pieces were exploded. I found after further research comparing differences between the original file and the file exported from 3DS Max that the values inside the translate tags in the original file are scaled down by a factor of 25.4 in the exported file from 3DS Max, representing the millimeters to inches conversion (1 inch = 25.4 millimeters). After scaling down values inside all of the translate tags by 25.4, the exploded pieces stuck back in, but the image needed further improvement. I have been able to create a new plugin in Blender that takes the original DAE file, replaces the primitive 2D tags tristrips and trifans with polygons, scales down the values inside the translate tags by a factor of 25.4, and saves the changes into a temporary DAE file. After the temporary DAE file is imported into Blender, the temp file is then deleted, keeping the original DAE file intact. Starting with a DAE file that is exported using the NASA Enterprise Visualization Application (NEVA), a Collada exporter, from CATIA gives better results. NEVA is a Design Visualization product that is used for exporting 3D models from CATIA. With NEVA, the up axis is defined in the top-level node if navigation gravity is enabled. With that file, just replacing the primitive tags tristrips and trifans with polygons in yields a much improved image in Blender. As we identify more differences between the original DAE file and the DAE file exported from 3DS Max, this plugin can be improved further. Our goal is to have a model that is formatted and sized for import into Unity, and we are trying out different 3D programs to see which will work best.

Ayyangar, Arjun↗
NASA NTRS1986

Object-oriented development

Object Oriented Development (OOD) is one of the extremely few software development methods actually designed for modern Ada language, real-time, embedded applications. OOD is a significant improvement over more traditional functional decomposition and modeling methods in that ODD: Better manages the size, complexity, and concurrancy of today's systems; Better addresses important software engineering principles such as abstract data types, levels of abstraction, and information hiding; Produces a better design that more closely matches reality; Produces more maintainable software by better localizing data and thus limiting the impact of requirements changes; and Specifically exploits the power of Ada. OOD is further explored in detail.

Firesmith, Donald G.↗