Search NASA⌕ Search

SEARCH · Search NASA

Results for “strain balance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Experimental studies of the laminar separation bubble on a two-dimensional airfoil at low Reynolds numbers

The laminar separation, transition and turbulent reattachment near the leading edge of a two-dimensional NACA 663-018 airfoil were investigated using a low speed, smoke visualization wind tunnel. Lift and drag force measurements were made using an external strain gauge balance for a chord Reynolds number range of 40,000 to 400,000. An extensive flow visualization study was performed and correlated with the force measurements. Experiments were also conducted with distributed surface roughness at the leading edge and external acoustic excitation to influence the development of the airfoil boundary layer. This study delineates the effects of angle of attack and chord Reynolds number on the separation bubble characteristics and airfoil performance

Mueller, T. J.↗
NASA NTRS1980

Full-scale wind-tunnel investigation of the effects of wing leading-edge modifications on the high angle-of-attack aerodynamic characteristics of a low-wing general aviation airplane

The paper presents the results of a recent investigation to determine the effects of wing leading-edge modifications on the high angle-of-attack aerodynamic characteristics of a low-wing general aviation airplane in the Langley Full-Scale Wind Tunnel. The investigation was conducted to provide aerodynamic information for correlation and analysis of flight-test results obtained for the configuration. The wind-tunnel investigation consisted of force and moment measurements, wing pressure measurements, flow surveys, and flow visualization studies utilizing a tuft grid, smoke and nonintrusive mini-tufts which were illuminated by ultra-violet light. In addition to the tunnel scale system which measured overall forces and moments, the model was equipped with an auxiliary strain-gage balance within the left wing panel to measure lift and drag forces on the outer wing panel independent of the tunnel scale system. The leading-edge modifications studied included partial- and full-span leading-edge droop arrangements as well as leading-edge slats.

Johnson, J. L., Jr.↗
NASA NTRS1982

Spanwise loading distribution and wake velocity surveys of a semi-span wing

The spanwise distribution of bound circulation on a semi-span wing and the flow velocities in its wake were measured in a wind tunnel. Particular attention was given to documenting the flow velocities in and around the development tip vortex. A two-component laser velocimeter was used to make the velocity measurements. The spanwise distribution of bound circulation, three components of the time-averaged velocities throughout the near wake their standard deviations, and the integrated forces and moments on a metric tip as measured by an internal strain gage balance are presented without discussion.

Felker, F. F., III↗
NASA NTRS1981

The development of cryogenic wind tunnels and their application to maneuvering aircraft technology

Cryogenic wind tunnels are considered as a means of studying high Reynolds number (Re) complicated flows encountered by high maneuvering lift and high angles of attack characteristic of modern fighter aircraft. Large decreases in the viscous force while the inertial force remains constant are provided by the use of cryogenic facilities. A 2.5 m square tunnel is nearing completion at the National Transonic Facility (NTF), and will be driven by synchronous motors having a total power of 120,000 hp. The tunnel, using N2 as the cryogenic fluid, will allow large Re sweeps at constant dynamic pressure and dynamic pressure, and aeroelastic sweeps at constant Re; full altitude (air density) and acceleration force simulation will also be possible. Advances in model and strain gage balance technologies for use at the NTF are outlined, and experiments with buffet are described.

Polhamus, E. C.↗
NASA NTRS1982

Wind-tunnel investigation of effects of wing-leading-edge modifications on the high angle-of-attack characteristics of a T-tail low-wing general-aviation aircraft

Exploratory tests have been conducted in the NASA-Langley Research Center's 12-Foot Low-Speed wind Tunnel to evaluate the application of wing-leading-edge devices on the stall-departure and spin resistance characteristics of a 1/6-scale model of a T-tail general-aviation aircraft. The model was force tested with an internal strain-gauge balance to obtain aerodynamic data on the complete configuration and with a separate wing balance to obtain aerodynamic data on the outer portion of the wing. The addition of the outboard leading-edge droop eliminated the abrupt stall of the windtip and maintained or increased the resultant-force coefficient up to about alpha = 32 degrees. This change in slope of the resultant-force coefficient curve with angle of attack has been shown to be important for eliminating autorotation and for providing spin resistance.

White, E. R.↗
NASA NTRS1986

Wind tunnel test evaluation of a Shuttle derived launch system

The Shuttle Derived Vehicle (SDV) is a proposed unmanned launch system configured using Shuttle elements. The SDV incorporates two solid rocket boosters, an external tank and three Space Shuttle main engines identical to those used in the present Space Transportation System. Two new elements, a recoverable propulsion/avionics module housing the main engines and an expendable payload module, complete the SDV configuration. This paper describes the activities and results of wind tunnel tests conducted to validate the aerodynamic and controllability characteristics of SDV configurations. The configuration variables consisted of the payload module diameter, length and nose shape. The tests were conducted in the NASA/Marshall Space Flight Center 14 inch trisonic wind tunnel. Aerodynamic force and moment data were obtained over a Mach number range of 0.6 to 4.96. The attack and sideslip angles were varied + or - 8.0 deg. Forces and moments were measured by a sting-supported six component strain gage balance.

Tewell, J. R.↗
NASA NTRS1987

Description of the US Army small-scale 2-meter rotor test system

A small-scale powered rotor model was designed for use as a research tool in the exploratory testing of rotors and helicopter models. The model, which consists of a 29 hp rotor drive system, a four-blade fully articulated rotor, and a fuselage, was designed to be simple to operate and maintain in wind tunnels of moderate size and complexity. Two six-component strain-gauge balances are used to provide independent measurement of the rotor and fuselage aerodynamic loads. Commercially available standardized hardware and equipment were used to the maximum extent possible, and specialized parts were designed so that they could be fabricated by normal methods without using highly specialized tooling. The model was used in a hover test of three rotors having different planforms and in a forward flight investigation of a 21-percent-scale model of a U.S. Army scout helicopter equipped with a mast-mounted sight.

Phelps, Arthur E., III↗
NASA NTRS1986

An investigation of tip planform influence on the aerodynamic load characteristics of semispan, upswept wing and wing-tip

A semi-span wing, equipped with an interchangeable tip, which was varied in planform and size was examined. Total wing aerodynamic loading was obtained from the wind tunnel scale system. The wing tip was mounted on a separate six-component strain gauge balance, which provided the aerodynamic loads on the tip. The tests were accomplished in the NASA Ames 7X10-Foot Wind Tunnel at a Mach number of 0.178. The aerodynamic load characteristics of the wing and of the tip were presented with the tip at several incidence angles relative to the wing inboard section.

Vanaken, Johannes M.↗
NASA NTRS1987

Lift distribution and velocity field measurements for a three-dimensional, steady blade/vortex interaction

A wind tunnel experiment simulating a steady three-dimensional helicopter rotor blade/vortex interaction is reported. The experimental configuration consisted of a vertical semispan vortex-generating wing, mounted upstream of a horizontal semispan rotor blade airfoil. A three-dimensional laser velocimeter was used to measure the velocity field in the region of the blade. Sectional lift coefficients were calculated by integrating the velocity field to obtain the bound vorticity. Total lift values, obtained by using an internal strain-gauge balance, verified the laser velocimeter data. Parametric variations of vortex strength, rotor blade angle of attack, and vortex position relative to the rotor blade were explored. These data are reported (with attention to experimental limitations) to provide a dataset for the validation of analytical work.

Dunagan, Stephen E.↗
NASA NTRS1988

Application of intelligent systems to wind tunnel test facilities

An approach to the application of intelligent-systems technology to the wind tunnel facilities at NASA Ames Research Center is outlined. To help fulfill the long-range goals of improving data quality and increasing personnel efficiency and management effectiveness, three major areas of intelligent systems application are recommended. The available state-of-the-art technology for developing the proposed systems is reviewed including the application of commercial software packages. The initial tasks and effort to develop these systems are recommended. A prototype expert system for selection of internal strain-gage balances has been built and is presented herein as an example model for the future systems.

Lo, Ching F.↗
NASA NTRS1988

Experimental measurements on an oscillating 70-degree delta wing in subsonic flow

A series of low-speed wind tunnel tests on a 70-degree sharp leading-edged delta wing at both static and dynamic conditions were performed to investigate the aerodynamic forces and moments. Forces and moments were obtained from a six component internal strain gauge balance. Static results compared well with the previous experimental findings. Large amplitude dynamic motion was produced by sinusoidally oscillating the model over a range of reduced frequencies. Substantial force and moment overshoots, a delay in dynamic stall, and hysteresis loops between the values of aerodynamnic loads in upstroke and downstroke motion were observed, all of which were strong functions of the reduced frequency. The aerodynamic forces and moments were influenced by the Reynolds number. Asymmetrical vortex bursting produced by nonzero sideslip angle created a complex rolling moment variations with angle of attack.

Soltani, M. R.↗
NASA NTRS1988

The pros and cons of code validation

Computational and wind tunnel error sources are examined and quantified using specific calculations or experimental data, and a substantial comparison of theoretical and experimental results, or a code validation, is discussed. Wind tunnel error sources considered include wall interference, sting effects, Reynolds number effects, flow quality and transition, and instrumentation such as strain gage balances, electronically scanned pressure systems, hot film gages, hot wire anemometers, and laser velocimeters. Computational error sources include math model equation sets, the solution algorithm, artificial viscosity/dissipation, boundary conditions, the uniqueness of solutions, grid resolution, turbulence modeling, and Reynolds number effects. It is concluded that although improvements in theory are being made more quickly than in experiments, wind tunnel research has the advantage of the more realistic transition process of a right turbulence model in a free-transition test.

Bobbitt, Percy J.↗
NASA NTRS1988

The pros and cons of code validation

Computational and wind tunnel error sources are examined and quantified using specific calculations of experimental data, and a substantial comparison of theoretical and experimental results, or a code validation, is discussed. Wind tunnel error sources considered include wall interference, sting effects, Reynolds number effects, flow quality and transition, and instrumentation such as strain gage balances, electronically scanned pressure systems, hot film gages, hot wire anemometers, and laser velocimeters. Computational error sources include math model equation sets, the solution algorithm, artificial viscosity/dissipation, boundary conditions, the uniqueness of solutions, grid resolution, turbulence modeling, and Reynolds number effects. It is concluded that, although improvements in theory are being made more quickly than in experiments, wind tunnel research has the advantage of the more realistic transition process of a right turbulence model in a free-transition test.

Bobbitt, Percy J.↗
NASA NTRS1990

National Transonic Facility model and model support vibration problems

Vibrations of models and model support system were encountered during testing in the National Transonic Facility. Model support system yaw plane vibrations have resulted in model strain gage balance design load limits being reached. These high levels of vibrations resulted in limited aerodynamic testing for several wind tunnel models. The yaw vibration problem was the subject of an intensive experimental and analytical investigation which identified the primary source of the yaw excitation and resulted in attenuation of the yaw oscillations to acceptable levels. This paper presents the principal results of analyses and experimental investigation of the yaw plane vibration problems. Also, an overview of plans for development and installation of a permanent model system dynamic and aeroelastic response measurement and monitoring system for the National Transonic Facility is presented.

Young, Clarence P., Jr.↗
NASA NTRS1989

Performance measurements of an airfoil at low Reynolds numbers

Performance characteristics of an Eppler 387 airfoil using both direct (force) and indirect (pressure) measurement techniques have been obtained at Reynolds numbers from 60,000 to 460,000 in the Langley Low-Turbulence Pressure Tunnel. Lift, drag, and pitching-moment data were obtained from two internally-mounted strain-gage balances specifically designed for small aerodynamic loads. Comparisons of these results with data from a pressure model of an Eppler 387 airfoil are included. Drag data for both models using the wake traverse method are compared with the balance data. Oil flow visualization and surface mounted hot-film sensors were used to determine laminar-separation and turbulent-reattachment locations. Problems associated with obtaining accurate wind-tunnel data at low Reynolds numbers are discussed.

Mcghee, Robert J.↗
NASA NTRS1991

Dynamic stall effects and applications to high performance aircraft

Recent research conducted at the NASA Langley Research Center on the effects of large amplitude pitching motions on the aerodynamic characteristics of modern fighter aircraft configurations is highlighted. Wind tunnel tests were conducted on simple flat-plate wings to gain understanding of the complex flow phenomena during unsteady motions at high angles of attack. Studies then progressed to a representative modern fighter configuration. Using a computer controlled dynamic apparatus, tests were conducted to investigate effects of pitch rate and motion time history and to determine the persistence of unsteady effects. Data were also obtained in sideslip and with control surface deflections to investigate dynamic effects on lateral stability and available control power. Force and moment data were obtained using a 6-component internal strain-gage balance. To aid in the interpretation of the results, flow visualization using a laser light-sheet system was also obtained. Results of these tests are discussed, along with their implications on the maneuverability of future advanced airplanes designed to operate in the highly dynamic, high angle-of-attack environment.

Brandon, Jay M.↗
NASA NTRS1987

Typical testing experience in cryogenic wind tunnels

Airfoil testing as a major activity of many wind tunnels is considered, and emphasis is placed on airfoil testing with sidewall boundary-layer removal, oscillating airfoil testing, and three-dimensional wake topology. Buffeting as the structural response of an aircraft or test model to the aerodynamic excitation produced by separated flows is analyzed, as well as flutter problems and testing techniques. Strain-gage balance studies, optical methods and visualization techniques, and fluid mechanics are examined. Focus is placed on a two-spot laser as a boundary-layer probe, hot-film gages, fluctuating-pressure measurements, skin-friction balance, and nonadiabatic airfoil testing. Boattail afterbody pressure tests are covered, and Space Shuttle Orbiter base drag and launch configuration are discussed.

Kilgore, Robert A.↗
NASA NTRS1991

Development of an intelligent hypertext system for wind tunnel testing

This paper summarizes the results of a system utilizing artificial intelligence technology to improve the productivity of project engineers who conduct wind tunnel tests. The objective was to create an intelligent hypertext system which integrates a hypertext manual and expert system that stores experts' knowledge and experience. The preliminary (Phase I) effort implemented a prototype IHS module encompassing a portion of the manuals and knowledge used for wind tunnel testing. The effort successfully demonstrated the feasibility of the intelligent hypertext system concept. A module for the internal strain gage balance, implemented on both IBM-PC and Macintosh computers, is presented. A description of the Phase II effort is included.

Lo, Ching F.↗