Search NASA⌕ Search

SEARCH · Search NASA

Results for “strengthening”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Oxide dispersoid coherency of a ferritic-martensitic 12Cr oxide-dispersion-strengthened alloy under self-ion irradiation

Ferritic-martensitic oxide-dispersion-strengthened (ODS) alloy has shown excellent mechanical property and high radiation tolerance. However, the stability of dispersoids during displacive irradiation in the individual ferritic and martensitic phases is unclear. In this work, the correlation among dispersoid coherency, size, density, and matrix phase are studied in dual-phase 12Cr ODS after 100 peak displacements-per-atom (dpa) irradiation at 475°C, using 3.5 MeV Fe 2+ self-ions. The size and density changes of coherent and incoherent dispersoids were analyzed as a function of irradiation depth. The average dispersoid size decreased after irradiation in both phases, and the large incoherent dispersoids in the tempered martensite phase underwent a more dramatic change than those in the ferrite phase. The dispersoid density significantly increased in the ferrite phase within the irradiated region, mostly resulting in an increase in coherent dispersoid density. On the other hand, only a small change in density was observed in the tempered martensite phase for both coherent and incoherent dispersoids. This study shows that dispersoid evolution is dramatically different in ferrite and tempered martensite phases.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Revealing the chemical environment of Cr, Fe, and Ni in high temperature-ultrafine precipitate strengthened steel subjected to low fluence neutron irradiation

High-temperature ultrafine-precipitate-strengthened (HT-UPS) steel has potential applications in advanced nuclear reactors as a structural material. However, little is currently known about its response to neutron irradiation. This research provides insight into the neutron irradiation-induced physicochemical changes of the major constituents in HT-UPS steels, including Fe, Cr, and Ni, using synchrotron X-ray absorption near edge structure (XANES) and diffraction. This study is the first known investigation using XANES to characterize HT-UPS steel to analyze the evolution of the atomic level chemistry. It was found that following irradiation, nucleation, ballistic dispersion, and/or coarsening of Cr 23 C 6 precipitates occurred at very low neutron irradiation fluences, from 0.003 displacements per atom (dpa) up to 0.3 dpa, at ~600°C, which were at least an order of magnitude lower than previous studies. Calculations of the angular momentum projections, partial density of states, and the XANES spectra confirmed the experimental findings of the Cr 23 C 6 precipitate evolution. In contrast, the local atomic structure around Fe and Ni atoms demonstrated irradiation resistance.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Friction stir welding and self-ion irradiation effects on microstructure and mechanical properties changes within oxide dispersion strengthened steel $\mathrm{MA956}$

We report the joining process for oxide dispersion strengthened (ODS) alloys remains a key challenge facing the nuclear community. The microstructure and mechanical properties were characterized in the base material and friction stir welded ODS MA956 irradiated with 5 MeV Fe 2+ ions from 400 to 500°C up to 25 dpa. Nanoindentation was performed to assess changes in hardness and yield stress, and the dispersed barrier hardening (DBH) model was applied to described results. A combination of scanning transmission electron microscopy (STEM) and atom probe tomography (APT) were used to assess evolution of the microstructure including dispersoids, network dislocations and dislocation loops, nanoclusters, and solid solution concentrations. Overall, softening was observed as a result of increased dose, which was exacerbated at 500°C. The formation and coarsening of new dispersoids was noted while nanoclusters tended to dissolve in the base material, and were not observed in the stir zone. Solute nanocluster evolution was identified as a primary driver of the changes in mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Investigating microstructural evolution in SolidStir™ extruded oxide dispersion strengthened 14YWT alloy fuel cladding tube

Structural components for extreme environments require advanced materials and manufacturing processes. One such advanced material is oxide dispersion strengthened (ODS) Fe–14 wt.%Cr–3W–0.4Ti–0.3Y 2 O 3 (14YWT), which is developed for components to be used in Gen IV and fusion nuclear reactors. However, the conventional manufacturing processes to produce components, such as fuel cladding tubes, either do not retain the desired microstructural attributes or are costly and less efficient. As a result, a more attractive option is a novel manufacturing process developed on the principle of friction stir welding or processing (FSW/P) and commercially referred to as SolidStir™ Extrusion (SSE). Here this study used the SSE technique to study the manufacturing and microstructural evolution of a fuel cladding tube made of ODS 14YWT alloy. The cladding extrusion by the SSE technique involved the use of ball-milled 14YWT powders with Y, Ti, and O in the solid solution and the use of a specially designed W-25Re-Hf tool for consolidation and extrusion of the powders. A scanning electron microscope (SEM), electron backscattered diffraction (EBSD), and transmission electron microscope (TEM) were utilized for microstructural characterization. A Keyence microscope captured macrostructural photographs of the extruded tube. EBSD examination of the extruded tube on both transverse and longitudinal cross-sections showed the presence of dynamically recrystallized grains and revealed that the average grain size of the transverse cross-section was smaller than that of the longitudinal cross-section. The texture was weak and consisted of some amount of shear texture. The presence of nano-oxide clusters or precipitates of Y, Ti, and O (pyrochlores) in the extruded tube was determined by TEM. Aging heat treatment caused the average precipitate size to decrease and the density to increase compared to the as-processed condition. The results indicated that SSE is a viable tool for manufacturing fuel cladding tubes with the desired microstructural attributes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Defect-specific strength factors and superposition model for predicting strengthening of ion irradiated Fe18Cr alloy

Here, a high-purity binary alloy Fe18Cr was subjected to heavy-ion irradiation in order to provide improved understanding of the irradiation effect on radiation hardening associated with dislocation loop and network formation, α’ precipitation. The specimens were irradiated with 8 MeV Fe ions (~2 μm ion range) to midrange doses of 0.37 and 3.7 dpa at 300, 350 and 450 °C using dose rates of ~10 –5 –10 –3 dpa/s. Nanoindentation testing was performed to extract the bulk equivalent hardness at low depth from these ion irradiated specimens. High-quality transmission electron microscopy (TEM) images were acquired by utilizing a flash electropolishing method on the Focused Ion Beam (FIB) prepared liftouts. An accurate calculation of the strength factor was provided based on detailed TEM characterization of the irradiated microstructures. A newly refined hardening superposition method was applied to combine the strengthening components from each microstructure. The good agreement between microstructure predicted strength and measured strength further demonstrated the fidelity to use hardening model to quantify the mechanical properties of ion irradiated materials.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Manufacturing Oxide Dispersion Strengthened (ODS) steel plate via cold spray and friction stir processing

Oxide dispersion strengthened (ODS) steels, traditionally fabricated by ball milling and conventional powder metallurgy techniques to achieve bulk form, followed by intricate rolling and thermal treatment steps to achieve plate or sheet form. Here, we present a novel processing route that combines cold spray (CS) with friction stir processing (FSP) to manufacture ODS steel plate directly from gas atomization reaction synthesis (GARS)-prepared powder, thus no rolling steps involved. Microstructural and mechanical characterizations were performed to assess the quality and properties of the resulting ODS steel plate. Our findings demonstrate that the slightly porous CS deposited layer was fully consolidated after FSP, yielding a fully dense ODS steel plate that exhibited a favorable tradeoff between strength and ductility upon extraction from the substrate. Furthermore, through microstructural analysis, we revealed the presence of an appreciable density (∼10 22 /m 3 ) of nano-sized oxide particles, with the majority being smaller than 5 nm via the combined CS + FSP fabrication route. This work serves as a first proof-of-concept demonstration of the manufacturing approach described herein, offering a possible alternative route for producing ODS steel plates.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Design of Silicide-Strengthened Nb–Si–Cr–(Mo) alloys for additive manufacturing

Three high–intermetallic volume Nb–Si–Cr–(Mo) alloys were designed using CALPHAD modeling with the goal of identifying high–specific strength, oxidation-resistant alloys that can be additively manufactured using powder bed fusion. The silicides Nb 5 Si 3 and Nb 9 Si 2 Cr3 were targeted as the primary strengthening phases, and the addition of Cr promoted the NbCr 2 phase. These alloys were cast and surface-processed with electron beam welding at different speeds to simulate additive manufacturing, and the phases and microstructures of both cast and welded regions were characterized. The weld processing was found to produce fine-grained microstructures in each alloy with fine-scale intermetallics uniformly distributed among a body-centered cubic Nb matrix. Microstructural refinement and hardness were found to increase with weld velocity; one alloy reached its highest hardness of approximately 16 GPa before the brittleness at higher velocities became detrimental. One alloy was found to be qualitatively the least brittle while also attaining a hardness of 13 GPa and was therefore identified as a good candidate for additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Laser powder bed fusion of oxide dispersion-strengthened IN718 alloys: A complementary study on microstructure and mechanical properties

In this study, two new grades of oxide dispersion strengthened (ODS) Inconel 718 (IN718) alloys were designed by the thermochemical CALPHAD method and produced by laser powder bed fusion (LPBF) technique. Alloys designated as IN718-YF and IN718-YFH, that consist Y 2 O 3 –FeO and Y 2 O 3 –FeO–Hf, respectively, were fabricated with >99.9 % densification using optimized process parameters. CALPHAD calculations were highly consistent with experimental findings, highlighting the formation of Al-containing Y–Ti–O and Y–Hf–O nano-oxides in both alloy types. Texture analyzes revealed no significant texture development in as-built (AB) or heat-treated (HT) alloys. Heat treatment was applied at 1050 °C for 1 h to enhance nano-oxide density. Further, the nano-oxide number density remained similar in IN718-YF while it decreased in IN718-YFH alloy as a result of carbide formation after the heat treatment. Besides, formation of secondary γ' particles was observed in the IN718-YFH/HT alloy. Even though the yield strengths of IN718-YF and IN718-YFH alloys in both AB and HT conditions were similar, the ductility of IN718-YFH was ~50 % less in almost all conditions compared to the ductility of IN718-YF. This has been shown to be as a result of irregular shaped micron-sized Y-Hf-O oxides, martensite formation in AB condition, increased amount of carbides and existence of secondary γ' particles in HT condition in IN718-YFH. High density of stacking faults (SF) forming at the interface of the nano-oxides have been detected in IN718-YF alloys. Besides dislocation/nanoparticle interactions, SFs which are responsible for the delocalization of the deformation improve the ductility of IN718-YF alloys. Overall, high temperature mechanical tests exhibit that both alloys have higher strength with improved ductility compared to the standard IN718 alloys, indicating the contribution of the nano-oxides.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Boron Nitride-Driven Strengthening of Aluminum Composites via Friction Stir Processing

Friction stir welding and processing (FSW/P) has emerged as an effective solid-state joining technique for fabricating metal matrix composites (MMCs), offering improved mechanical properties through refined microstructural evolution. In this study, an aluminum-boron nitride nanoparticle (Al-BNNP) composite was synthesized via FSW, and its indentation-based mechanical properties were systematically evaluated. Microhardness mapping across the weld cross-section revealed a progressive increase in hardness toward the stir zone (SZ), attributed to severe plastic deformation, dynamic recrystallization (DRX), and the reinforcing effect of BNNPs. Profilometry-based indentation plastometry (PIP) inferred yield strength (YS) demonstrates a 47.8% increase compared to the base metal (BM) and a 75% improvement compared to FSP pure aluminum reported in literature. This enhancement is attributed to strengthening mechanisms, including grain boundary pinning, load transfer, and increased dislocation density. The strain rate sensitivity (SRS) measurements at the nanoscale demonstrated a substantial decrease in the SZ, correlated with ultrafine grain structures and strong BNNP-matrix interactions. Activation volume analysis revealed a significant reduction in the SZ, suggesting that dislocation motion is increasingly restricted by dislocation-dislocation and dislocation-particle interactions. These findings suggest that incorporating BNNPs in FSW/P enables tailoring the microstructure without thermal degradation of the secondary particles, thereby significantly enhancing the mechanical performance of aluminum composites, particularly for structural applications in aerospace and automotive industries.

Aluminum↗
DOE OSTI2025

Microstructure and mechanical behavior of a TiC nanoprecipitate strengthened V Alloy

The V-4Cr-4Ti (V44) alloys have been proposed as the prime candidate structural material for self-cooled liquid Li blanket and other designs for fusion energy applications. However, the applications of the V44 alloy are limited to a narrow operation temperature window, due to reduction in creep strength at or above 700 °C and susceptibility to irradiation hardening and embrittlement when irradiated below 400 °C. Here, in this work, we explore the feasibility of designing a novel V alloy to form a high number density of TiC nanoprecipitates, in order to simultaneously improve creep strength and provide defect sinks to mitigate irradiation hardening. Computational thermodynamics was used to design a new alloy (V44C) to achieve our goal of high TiC nanoprecipitates density within the alloy V44 matrix. To ensure scalability, the new alloy was made through arc-melting and ingot-casting followed by hot forging, cold rolling and heat treatments of homogenization and precipitation aging. The microstructure was characterized by SEM, TEM, XRD and APT, confirming the existence of nanoprecipitates predicted in the thermodynamic calculations. In addition to microstructural evaluation tensile properties at room temperature and 700 °C, and Charpy impact energy at room temperature were measured. The microstructure and mechanical properties were then compared with those from a historic reference V44 alloy. The tensile strength improvement in V44C was rationalized based on particle and solid solution strengthening mechanism. The fracture behavior was discussed based on the fractography results and necking deformation behavior.

Alloys development↗
DOE OSTI2020

Strategies for simultaneous strengthening and toughening via nanoscopic intracrystalline defects in a biogenic ceramic

While many organisms synthesize robust skeletal composites consisting of spatially discrete organic and mineral (ceramic) phases, the intrinsic mechanical properties of the mineral phases are poorly understood. Using the shell of the marine bivalve Atrina rigida as a model system, and through a combination of multiscale structural and mechanical characterization in conjunction with theoretical and computational modeling, we uncover the underlying mechanical roles of a ubiquitous structural motif in biogenic calcite, their nanoscopic intracrystalline defects. These nanoscopic defects not only suppress the soft yielding of pure calcite through the classical precipitation strengthening mechanism, but also enhance energy dissipation through controlled nano- and micro-fracture, where the defects’ size, geometry, orientation, and distribution facilitate and guide crack initialization and propagation. These nano- and micro-scale cracks are further confined by larger scale intercrystalline organic interfaces, enabling further improved damage tolerance.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Anomalous lattice thermal conductivity increase with temperature in cubic GeTe correlated with strengthening of second-nearest neighbor bonds

Understanding thermal transport mechanisms in phase change materials is critical to elucidating the microscopic picture of phase transitions and advancing thermal energy conversion and storage. Experiments consistently show that cubic phase germanium telluride (GeTe) has an unexpected increase in lattice thermal conductivity with rising temperature. Despite its ubiquity, resolving its origin has remained elusive. In this work, we carry out temperature-dependent lattice thermal conductivity calculations for cubic GeTe through efficient, high-order machine-learned models and additional corrections for coherence effects. We corroborate the calculated phonon properties with our inelastic X-ray scattering measurements. Our calculated lattice thermal conductivity values agree well with experiments and show a similar increasing trend. Through additional bonding strength calculations, we propose that a major contributor to the increasing lattice thermal conductivity is the strengthening of second-nearest neighbor interactions. The findings herein serve to deepen our understanding of thermal transport in phase-change materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Soil moisture gradients strengthen mesoscale convective systems by increasing wind shear

Mesoscale convective systems are a class of storm linked to extensive flooding and other destructive hazards in many regions globally. In West Africa, soil moisture impacts provide a valuable source of predictability for mature storm hazards, but little is known about mature storm sensitivity to soil moisture in other climatic regions. Here we use a storm track dataset, satellite observations and reanalysis fields to investigate the response of mature storms to soil moisture in seven global storm hotspots—West Africa, India, South America, South Africa, Australia and the United States Great Plains. We demonstrate that mesoscale soil moisture gradients (~500 km) can enhance storms by driving increased vertical wind shear conditions, a crucial ingredient for storm organization, through the strengthening of atmospheric temperature gradients. This is evidenced by a 10–30% increase in precipitation feature size and rainfall for the largest storms on days with favourable soil moisture gradients compared with unfavourable gradients. Global simulations confirm that soil moisture gradients influence wind shear. The results demonstrate the importance of soil moisture feedbacks for accurate forecasting of mesoscale convective systems and future projections of extreme events under climate change.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Asian-Australian summer monsoons linkage to ENSO strengthened by global warming

The El Niño-Southern Oscillation (ENSO) used to affect the Asian summer monsoon (ASM) and Australian summer monsoon (AusSM) precipitation in different ways but global warming may have changed it. This study built robust annual ASM (AusSM) precipitation reconstructions during 1588–2013 (1588–1999) to examine the ENSO-monsoon relationship and how it has changed. During the period of 1588–1850 when natural climate variability was dominant, the ENSO-monsoon and inter-monsoon relationship was weak and non-stationary. Since 1850, however, both the inter-monsoon and ENSO-monsoon relationships saw an enhancement and this trend has been persistent to the present day, suggesting the influence of anthropogenic climate warming. Further analysis of climate model projections found that global warming can strengthen the ENSO-monsoon association that, subsequently, acts to synchronize the ASM and AusSM variations.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Theoretical and experimental quantification of Suzuki segregation enthalpy and strengthening mechanisms in a binary alloy

Solute segregation to planar defects in metallic alloys has been shown to drastically alter mechanical properties. While various works using first-principles and thermodynamic calculations have studied the fundamental driving forces for solute segregation via the Suzuki criterion, planar defect energy, or a comparison of energies of the HCP-like phase and FCC matrix, a quantitative experimental and computational comparison of equilibrium composition and segregation enthalpies has not yet been reported. In this work, we predict the equilibrium composition and segregation enthalpy to intrinsic stacking faults in a Ni-60Co (at.%) alloy and compare the results to two independent experimental methods. We observed that Co segregates to the innermost two planes of the intrinsic stacking fault, and we found that the experimental segregation enrichment, measured from transmission electron microscopy energy dispersive X-ray spectroscopy, of the faults is 6.8 at.% Co, which is 2.2 at.% less than the predicted value at the same temperature. We also find that the segregation enthalpy measured from the composition profile is −21.1 ± 6.4 meV/atom and separately from differential scanning calorimetry segregation enthalpy is −33.2 meV/atom, whereas the predicted enthalpy is −31 ± 1 meV/atom. Based on these results, we determine that segregation occurs very rapidly, within 8 min at temperatures as low as 36% of the homologous solidus temperature. Furthermore, this analysis provides an overview of the possible dislocation mechanisms responsible for strengthening effects due to solute segregation, and concludes that changes in room temperature hardness from local phase transformation is likely tied to post-segregation room temperature equilibrium partial separation distance.

Ab initio calculation↗
DOE OSTI2023

Machine learned interatomic potential for dispersion strengthened plasma facing components

Tungsten (W) is a material of choice for the divertor material due to its high melting temperature, thermal conductivity, and sputtering threshold. However, W has a very high brittle-to-ductile transition temperature, and at fusion reactor temperatures (≥1000 K), it may undergo recrystallization and grain growth. Dispersion-strengthening W with zirconium carbide (ZrC) can improve ductility and limit grain growth, but much of the effects of the dispersoids on microstructural evolution and thermomechanical properties at high temperatures are still unknown. We present a machine learned Spectral Neighbor Analysis Potential for W–ZrC that can now be used to study these materials. In order to construct a potential suitable for large-scale atomistic simulations at fusion reactor temperatures, it is necessary to train on ab initio data generated for a diverse set of structures, chemical environments, and temperatures. Further accuracy and stability tests of the potential were achieved using objective functions for both material properties and high temperature stability. Additionally, validation of lattice parameters, surface energies, bulk moduli, and thermal expansion is confirmed on the optimized potential. Tensile tests of W/ZrC bicrystals show that although the W(110)–ZrC(111) C-terminated bicrystal has the highest ultimate tensile strength (UTS) at room temperature, observed strength decreases with increasing temperature. At 2500 K, the terminating C layer diffuses into the W, resulting in a weaker W–Zr interface. Meanwhile, the W(110)–ZrC(111) Zr-terminated bicrystal has the highest UTS at 2500 K.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Void formation during cyclic oxidation of oxide dispersion strengthened FeCrAl alloys

Here, oxide dispersion strengthened FeCrAl alloys are considered for various high-temperature applications due to their excellent mechanical properties and oxidation resistance, but void formation is a concern for component durability. Cyclic oxidation testing was conducted on alloy MA956 and PM2000 at 1100–1200ºC for durations of up to 10,000 h and the void content was determined from optical cross-sections by image analysis. At 1100ºC, 100 h cycle, the low void concentrations measured were consistent with two competing mechanisms proposed in the literature: coalescence of process-induced nano-voids and alloy sintering. At 1200ºC using 1 h cycles, the void concentration was much higher, reaching ~3% to 6% for specimens tested to breakaway oxidation. The void growth was attributed to the high oxidation rates and the annihilation of oxidation-induced vacancies at the surface of the process-induced voids.

36 MATERIALS SCIENCE↗