SEARCH · Search NASA

Results for “stripping”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

All sources NASA NTRS DOE OSTI

DOE OSTI2022

Accidental Disassembly of a Multi Branch Outlet Strip with Surge Protector (Investigation Report)

On December 16 a worker attempted to disconnect a computer plug from a multi outlet surge protector strip. The plastic housing of the surge protector disintegrated while the plug was pulled exposing the bare conductors of the internal wiring. The worker disconnected the wall plug on the multi outlet strip and de-energized the outlet strip. The worker contacted the FOD and the FOD called the ISR DESO for advice. The DESO collected the pieces and performed an autopsy on the device.

42 ENGINEERING↗

DOE OSTI2024

Performance of Pixel and Strip AC-LGAD Sensors with Different Design Parameter on a 120 GeV Proton Beam

We present the results of an extensive evaluation of strip and pixel AC-LGAD sensors tested with a 120 GeV proton beam, focusing on the influence of design parameters on the sensor temporal and spatial resolutions. Results show that reducing the thickness of pixel sensors significantly enhances their time resolution, with 20- μm-thick sensors achieving around 20 ps. Uniform performance is attainable with optimized sheet resistance, making these sensors ideal for future timing detectors. Conversely, 20-μm-thick strip sensors exhibit higher jitter than similar pixel sensors, negatively impacting time resolution, despite reduced Landau fluctuations with respect to the 50-μm-thick versions. Additionally, it is observed that a low resistivity in strip sensors limits signal size and time resolution, whereas higher resistivity improves performance. This study highlights the importance of tuning the n+ sheet resistance and suggests that further improvements should target specific applications like the Electron-Ion Collider or other future collider experiments. In addition, the detailed performance of four AC-LGADs sensor designs is reported as examples of possible candidates for specific detector applications. These advancements position AC-LGADs as promising candidates for future 4D tracking systems, pending the development of specialized readout electronics.

Lara, Carlos Pérez↗

DOE OSTI2025

The ATLAS Inner Tracker Strip Detector System for the Phase-II Large Hadron Collider Upgrade

ATLAS is currently preparing for the HL-LHC upgrade, with an all-silicon Inner Tracker (ITk) that will replace the current Inner Detector. The ITk will feature a pixel detector surrounded by a strip detector, with the strip system consisting of four barrel layers and 12 endcap disks. After successful completion of a large-scale prototyping program, final design reviews have been completed in key areas, such as sensors, modules, front-end electronics, and ASICs. We present an overview of the strip system and highlight the final design choices of sensors, modules, and ASICs. We summarize the results achieved during prototyping and the current status of production and pre-production on various detector components, with an emphasis on QA and QC procedures.

Duden, Emily (ORCID:0000000290929344)↗

NASA NTRS1971

Analytical prediction of the heat transfer from a blood vessel near the skin surface when cooled by a symmetrical cooling strip

An analytical method was developed to estimate the amount of heat extracted from an artery running close to the skin surface which is cooled in a symmetrical fashion by a cooling strip. The results indicate that the optimum width of a cooling strip is approximately three times the depth to the centerline of the artery. The heat extracted from an artery with such a strip is about 0.9 w/m-C which is too small to affect significantly the temperature of the blood flow through a main blood vessel, such as the carotid artery. The method is applicable to veins as well.

Chato, J. C.↗

NASA NTRS1972

An integral equation approach to the strip problem

A semi-infinite strip held rigidly on its short end is considered. Loads in the strip at infinity (far away from the fixed end) are prescribed. Integral transform technique is used to provide an exact formulation of the problem in terms of a singular integral equation. Stress singularity at the strip corner is obtained from the singular integral equation which is then solved numerically. Stresses along the rigid end are determined and the effect of the material properties on the stress intensity factor is presented. The method can also be applied to the problem of a laminate composite with a flat inclusion normal to the interfaces.

Gupta, G. D.↗

NASA NTRS1973

Ecological effects of strip mining in Ohio

The author has identified the following significant results. ERTS-1 imagery has identified when reclamation has proved successful, when little lateral extension has occurred in the strip mine, when water has filled an impoundment (4 - 5 acres), and detected narrow contour mines. It has been proven that the CCT contains more information than the imagery received from NASA. A stream is visible in the band 7 digital printout that is not visible in the imagery. Also narrow bodies of water between the high wall and spoils bank and small impoundments (2 - 3 acres) are observed in the digital printout and not in the imagery. Disruption maps (water and bare earth within the mined area) can be made by statistically processing the CCT (decision imagery) or mapping the digital printout with a Bendix digitizer. Reclamation maps will be produced in the near future through decision imagery. There seems little doubt that the mapping of present stripping and the monitoring of the strip mine cycle for changes are practical. Disruption mapping is now an operational capability.

Chase, P. E.↗

NASA NTRS1973

The problem of a finite strip compressed between two rough rigid stamps

A finite strip compressed between two rough rigid stamps is considered. The elastostatic problem is formulated in terms of a singular integral equation from which the proper stress singularities at the corners are determined. The singular integral equation is solved numerically to determine the stresses along the fixed ends of the strip. The effect of material properties and strip geometry on the stress intensity factor is presented graphically.

Gupta, G. D.↗

NASA NTRS1973

The use of ERTS-1 MSS data for mapping strip mines and acid mine drainage in Pennsyvania

Digital processing of ERTS-I MSS data for areas around the west branch of the Susquehanna River permits identification of stripped areas including ones that are not discernible from visual analysis of ERTS imagery. Underflight data and ground-based observations are used for ground-truth and as a basis for designing more refined operators to make sub-classifications of stripped areas, particularly with regard to manifestations of acid mine drainage; because of associated diagnostic effects on vegetation, seasonal changes in classifiction criteria are being documented as repeated, cloud-free ERTS-I coverage of the same area becomes available. Preliminary results indicate that ERTS data can be used to moniter not only the total extent of stripping in given areas but also the effectiveness of reclamation and pollution abatement procedures.

Alexander, S. S.↗

NASA NTRS1973

An integral equation approach to the semi-infinite strip problem.

A semi-infinite strip held rigidly on its short end is considered. Loads in the strip at infinity (far away from the fixed end) are prescribed. The integral transform technique is used to provide an exact formulation of the problem in terms of a singular integral equation. The stress singularity at the strip corner is obtained from the singular integral equation, which is then solved numerically. Stresses along the rigid end are determined, and the effect of the material properties on the stress-intensity factor is presented. The method can also be applied to the problem of a laminate composite with a flat inclusion normal to the interfaces.

Gupta, G. D.↗

NASA NTRS1974

Automatic mapping of strip mine operations from spacecraft data

The author has identified the following significant results. Computer techniques were applied to process ERTS tapes acquired over coal mining operations in southeastern Ohio on 21 August 1972 and 3 September 1973. ERTS products obtained included geometrically-correct map overlays, at scales from 1:24,000 to 1:250,000, showing stripped earth, partially reclaimed earth, water, and natural vegetation. Computer-generated tables listing the area covered by each land-water category in square kilometers were also produced. By comparing these mapping products, the study demonstrates the capability of ERTS to monitor changes in the extent of stripping and reclamation. NASA C-130 photography acquired on 7 September 1973 when compared with the ERTS products generated from the 3 September 1973 tape established the categorization accuracy to be better than 90%. It is estimated that the stripping and reclamation maps and data were produced from the ERTS CCTs at a tenth of the cost of conventional techniques.

Rogers, R. H.↗

NASA NTRS1974

Automated strip mine and reclamation mapping from ERTS

In response to the urgent need for a faster and more economical means of generating strip mine and reclamation maps, a study was conducted to evaluate the suitability of using ERTS computer compatible tape for automatic mapping. The procedure uses computer target spectral recognition techniques as a basis for classification. The area encompassed by this investigation includes five counties in eastern Ohio that comprise nearly 7,500 square kilometers (3,000 square miles). The counties have been disrupted by coal mining since the early 1800's, and strip mining has been practiced in all of them. The environmental effects of strip mining are also discussed.

Pettyjohn, W. A.↗

NASA NTRS1975

The problem of a finite strip compressed between two rough rigid stamps

Gupta, G. D.↗

NASA NTRS1978

Strip antennas in a dielectric slab

A method is proposed to analyze electrically thin strip antennas in an electrically thin dielectric slab. The method combines a moment method solution and a modification of the piecewise sinusoidal reaction formulation for thin wire radiators in a homogeneous medium. Strip antennas in both homogeneous and inhomogeneous media are considered. The analysis has the advantages that it is applicable to a wide variety of antenna geometries, that the slab may be of finite or infinite extent, and that the presence of the slab introduces no new unknowns in the moment method solution. Numerical calculations and verification by measurements are presented for the impedance of a strip dipole in a dielectric slab.

Newman, E. H.↗

NASA NTRS1980

Stress intensity factors and COD in an orthotropic strip

The elasticity problem for an orthotropic strip or a beam with an internal or an edge crack under general loading conditions is considered. The numerical results are given for four basic loading conditions, namely, uniform tension, pure bending, three point bending, and concentrated surface shear loading. For the strip with an edge crack additional results regarding the crack opening displacements are obtained by using the plastic strip model. A critical quantity which is tabulated is the maximum compressive stress in the plane of the crack. It is shown that this stress may easily exceed the yield limit in compression and hence may severely limit the range of application of the plasticity results.

Kaya, A. C.↗

NASA NTRS1983

Terminal Strip Facilitates Printed-Circuit Board Changes

Laminanted copper and polyimide terminal strip makes it easy to modify printed-circuit (PC) board, after board has been fabricated. When epoxied over conductors or insulating portion of PC board, strip provides series of solder-coated copper conductor pads to which integrated-circuit leads are soldered for functional changes. Terminal strips accommodate leads on dual inline IC package or as staggered single or multiple leads on planar mounted flatpacks.

Pinto, E. A.↗

NASA NTRS1982

The crack and wedging problem for an orthotropic strip

The plane elasticity problem for an orthotropic strip containing a crack parallel to its boundaries is considered. The problem is formulated under general mixed mode loading conditions. The stress intensity factors depend on two dimensionless orthotropic constants only. For the crack problem the results are given for a single crack and two collinear cracks. The calculated results show that of the two orthotropic constants the influence of the stiffness ratio on the stress intensity factors is much more significant than that of the shear parameter. The problem of loading the strip by a rigid rectangular lengths continuous contact is maintained along the wedge strip interface; at a certain critical wedge length the separation starts at the midsection of the wedge, and the length of the separation zone increases rapidly with increasing wedge length.

Cinar, A.↗

NASA NTRS1985

X-Band Strip-Line Power Divider/Combiner

Strip-line circuit for X-band signals both divides and combines microwave power for distributed amplifier. Strip-line pattern (foil pattern over insulating layer over ground plane) laid out so all eight distributed ports lie at electrical distances of odd integral multiples of half wavelength from main input/output port. Strip line used as power divider and as power combiner.

Conroy, B. L.↗

NASA NTRS1983

The crack and wedging problem for an orthotropic strip

Cinar, A.↗