Search NASA⌕ Search

SEARCH · Search NASA

Results for “structural strain”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

TPSAS-NF1676L-13664-DND

The safety of aerospace vehicles is largely dependent on the ability of modern non-destructive evaluation (NDE) tools to accurately detect structural damage before a critical flaw size is reached. However, existing NDE technologies are inherently limited by the physical response of the materials being inspected making the detection of small cracks or pre-crack damage difficult. One innovative solution to this problem is to create a multifunctional metallic material that can be used in structural applications and contains second phase sensory particles that significantly enhance the ability of conventional NDE techniques to detect incipient damage during use and at regularly scheduled inspections. Ferromagnetic shape-memory alloys (FSMAs) are an ideal material for use as this second phase material as they undergo a uniform and repeatable change in both magnetic properties and crystallographic structure when strained. These changes are more readily detected than small cracks, thereby, allowing for enhanced detection of damage by conventional NDE techniques. In this study, a multifunctional metallic material was produced by embedding the sensory material particles within an aluminum alloy to form a sensory alloy. The NDE response of the FSMA and the sensory alloy during tension/compression and fatigue loading have been investigated. These results suggest that sensory alloys can be utilized for improved on-board structural health monitoring and to improve the accuracy and reduce time for ground-based inspection.

T. A. Wallace↗
NASA NTRS1960

Experimental Study of a Hot Structure for a Reentry Vehicle

A large structural model of a reentry vehicle has been built incorporating design concepts applicable to a radiation-cooled vehicle. Thermal-stress alleviating features of the model are discussed. Environmental tests on the model include approximately 100 cycles of loading at room temperature and 33 cycles of combined loading and-heating up to temperatures of 1,6000 F. Measured temperatures are shown for typical parts of the model. Comparisons are made between experimental and calculated deflections and strains. The structure successfully survived the heating and loading environments.

Pride, Richard A.↗
NASA NTRS1973

Experiments to study strain gage load calibrations on a wing structure at elevated temperatures

Laboratory experiments were performed to study changes in strain-gage bridge load calibrations on a wing structure heated to temperatures of 200 F, 400 F, and 600 F. Data were also obtained to define the experimental repeatability of strain-gage bridge outputs. Experiments were conducted to establish the validity of the superposition of bridge outputs due to thermal and mechanical loads during a heating simulation of Mach 3 flight. The strain-gage bridge outputs due to load cycle at each of the above temperature levels were very repeatable. A number of bridge calibrations were found to change significantly as a function of temperature. The sum of strain-gage bridge outputs due to individually applied thermal and mechanical loads compared well with that due to combined or superimposed loads. The validity of superposition was, therefore, established.

Monaghan, R. C.↗
DOE OSTI2025

Molecular and structural characterization of a Bacillus cereus strain producing an anthrax-like capsule

Bacillus cereus is a ubiquitous Gram-positive, spore-forming, rod-shaped saprophytic bacterium, occasionally reported to cause food-borne illnesses. However, instances of B. cereus strains harboring anthrax toxin and capsule genes have elevated certain strains as formidable pathogens and biothreats. This study focuses on the genomic analysis and the structural characterization of capsular material produced by the virulent B. cereus PATH2418 strain, isolated from the wound of a traumatic open fracture patient. The genome was sequenced using Nanopore MinION sequencing, revealing a chromosome of 5,270,283 bp and three plasmids. One plasmid, pATH1, was found to encode an operon for the biosynthesis of a bacterial capsule. This operon had sequence homology to the Bacillus anthracis capBCADE operon, which encodes the poly-γ-D-glutamate (PDGA) capsule. The capsule production in B. cereus PATH2418 was influenced by temperature and CO 2 levels. Structural analysis of the capsular material using a combined approach of nuclear magnetic resonance (NMR) and high-performance liquid chromatography (HPLC) techniques confirmed the presence of a high-molecular-weight poly-γ-glutamate capsule, with an enantiomeric composition of approximately 67% D-glutamic acid and 33% L-glutamic acid, matching that of B. anthracis.

Bacillus cereus↗
DOE OSTI2025

Spherical Congeners of Polyaromatic Compounds Approaching C 20 - and C 60 -Fullerene-Type Structures

A series of three symmetric, hollow spherical, and shape-persistent molecular organic cages analogous to C 20 and C 60 were examined by computational modeling, analyzing structural elements, strain indicators, and physical properties relevant for potential applications. The compounds are covalent aromatic cages based on 1,3,5-substituted benzene nodes linked by paraphenylene or para-pyrenylene-connectors, with diameters varying from 2.3 to 4.2 nm. The apertures in the cage interior are varied by virtue of the cage type (C 20 - or C 60 -type cage) and the linear connectors placed between the C 6 H 3 -units. NBO and MESP analyses indicate the presence of electrophilic and nucleophilic sites in the molecular skeleton. In the cages with the phenylene-connectors, the HOMO−LUMO gaps are close to 4.0 eV. In the cage coated with an enlarged polyaromatic spacer (pyrene-unit), the gap is reduced by approximately 0.4 eV.

Aromatic compounds↗
DOE OSTI2023

Electron Microscopy Studies of Soft Nanomaterials

This review highlights recent efforts on applying electron microscopy (EM) to soft (including biological) nanomaterials. We will show how developments of both the hardware and software of EM have enabled new insights into the formation, assembly, and functioning (e.g., energy conversion and storage, phonon/photon modulation) of these materials by providing shape, size, phase, structural, and chemical information at the nanometer or higher spatial resolution. Specifically, we first discuss standard real-space two-dimensional imaging and analytical techniques which are offered conveniently by microscopes without special holders or advanced beam technology. The discussion is then extended to recent advancements, including visualizing three-dimensional morphology of soft nanomaterials using electron tomography and its variations, identifying local structure and strain by electron diffraction, and recording motions and transformation by in situ EM. On these advancements, we cover state-of-the-art technologies designed for overcoming the technical barriers for EM to characterize soft materials as well as representative application examples. Here, the even more recent integration of machine learning and its impacts on EM are also discussed in detail. With our perspectives of future opportunities offered at the end, we expect this review to inspire and stimulate more efforts in developing and utilizing EM-based characterization methods for soft nanomaterials at the atomic to nanometer length scales in academic research and industrial applications.

Imaging↗
DOE OSTI2025

Exploring Domain-Wall Pinning in Ferroelectrics via Automated High-Throughput Atomic Force Microscopy

Domain-wall dynamics in ferroelectric materials are strongly position-dependent, since each polar interface is locked into a unique local microstructure. This necessitates spatially resolved studies of wall pinning using scanning-probe microscopy techniques. The pinning centers and pre-existing domain walls are usually sparse within the image plane, precluding the use of dense hyperspectral imaging modes and requiring time-consuming human experimentation. Here, a large-area epitaxial PbTiO 3 film on cubic KTaO 3 was investigated to quantify the electric-field-driven dynamics of the polar–strain domain structures using ML-controlled automated piezoresponse force microscopy. Analysis of 1500 switching events reveals that domain-wall displacement depends not only on field parameters but also on the local ferroelectric–ferroelastic configuration. For example, twin boundaries in polydomains regions, like a 1 – /c+ ∥ a 2 – /c – , stay pinned up to a certain level of bias magnitude and change only marginally as the bias increases from 20 to 30 V, whereas single-variant boundaries, like the a 2 + /c + ∥ a 2 – /c – stack, are already activated at 20 V. These statistics on the possible ferroelectric and ferroelastic wall orientations, together with the automated high-throughput AFM workflow, can be distilled into a predictive map that links domain configurations to pulse parameters. Here, this microstructure-specific rule set forms the foundation for the design of ferroelectric memories.

automated scanning probe microscopy↗
DOE OSTI2026

Heteroepitaxial control of thickness, strain, and domain architecture in few-layer ferroelectric tin monochalcogenides

Thin-film epitaxy and epitaxial strain have been widely exploited to tune domain configurations, switching behavior, and ferroic properties in conventional three-dimensional ferroelectric thin films; however, its application to controlling the properties of two-dimensional (2D) ferroelectrics has remained largely unexplored. Here, using SnX (X = Se, S) as a model system, we demonstrate heteroepitaxial control of thickness, strain state, and domain architecture in few-layer ferroelectric SnX via growth on monolayer MoS2 van der Waals (vdW) templates. Compared with conventional growth, MoS2-templated heteroepitaxy promotes epitaxial alignment, yielding ultrathin SnSe films with improved crystalline quality, full areal coverage, and enlarged lateral dimensions. Strong interfacial epitaxial coupling induces pronounced in-plane strain and stabilizes a hierarchical ferroelastic domain architecture, in which long-range 90° stripe domains are further subdivided into nanoscale rotational variants, as revealed by scanning transmission electron microscopy and synchrotron X-ray microscopy. Piezoresponse force microscopy and second-harmonic polarimetry confirm robust in-plane polarization, while ferroelectricity in SnSe is established through polarization-electric field hysteresis and nonvolatile ferroelectric resistive switching with on/off ratios approaching 1000. A nonvolatile, switchable ferroelectric diode effect further evidences direct coupling between polarization and charge transport. Notably, ferroelectric switchability exhibits a strong thickness dependence and is preserved only below ∼10 layers. This vdW heteroepitaxial strategy is further extended to ferroelectric SnS. The seamless heteroepitaxial integration of 2D ferroelectrics with CMOS-compatible, wafer-scale MoS2 templates provides a general and scalable route for strain-enabled structural and ferroelectric engineering in emerging memory and low-power optoelectronic applications.

Wang, Yueyin↗
DOE OSTI2024

Reducing crystal symmetry to generate out-of-plane Dzyaloshinskii–Moriya interaction

The Dzyaloshinskii-Moriya antisymmetric exchange interaction (DMI) stabilises topological spin textures with promising future spintronics applications. According to crystal symmetry, the DMI can be categorized as four different types that favour different chiral textures. Unlike the other three extensively-investigated types, out-of-plane DMI, as the last type that favours in-plane chirality, remained missing so far. Here we apply point-group-dependent DMI matrix analysis to show that out-of-plane DMI exists under reduced crystal symmetry. Through strain and structure engineering, we show how C s symmetry is realized in ultrathin magnets and observe the out-of-plane DMI stabilised in-plane chirality using spin-polarized electron microscopy. Our results show that extremely low out-of-plane DMI strengths at µeV/atom are sufficient to stabilise topological spin textures, including merons and bimerons. We also demonstrate field-induced reversible control of the in-plane chirality and merons. Our findings open up untapped paths on topological magnetic textures and their potential applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Development of an ultrahigh affinity, trimeric ACE2 biologic as a universal SARS-CoV-2 antagonist

Abstract Severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), responsible for the COVID-19 pandemic, utilizes membrane-bound, angiotensin-converting enzyme II (ACE2) for internalization and infection. We describe the development of a biologic that takes advantage of the proximity of the N-terminus of bound ACE2 to the three-fold symmetry axis of the spike protein to create an ultrapotent, trivalent ACE2 entry antagonist. Distinct disulfide bonds were added to enhance serum stability and a single point mutation was introduced to eliminate enzymatic activity. Through surface plasmon resonance, pseudovirus neutralization assays, and single-particle cryo-electron microscopy, we show this antagonist binds to and inhibits SARS-CoV-2 variants. We further show the antagonist binds to and inhibits a 2003 SARS-CoV-1 strain. Collectively, structural insight has allowed us to design a universal trivalent antagonist against all variants of SARS-CoV-2 tested, suggesting it will be active against the emergence of future mutants.

Gonzales, Juliet (ORCID:0000000327219566)↗
NASA NTRS1964

Structural loads.

Structural loads calculated for launch and reentry vehicles, noting extra loads due to system failures

REENTRY VEHICLE↗
NASA NTRS1974

The static nonlinear analysis of shells of revolution (SNASOR II)

Utilizing stiffness matrices and supplying as input the loading and boundary conditions, program generates equilibrium equations for structure. Nonlinear strain energy terms result in pseudogeneralized forces which are combined with applied generalized forces. Resulting set of nonlinear algebraic equilibrium equations is solved by one of several methods.

Stricklin, J. A.↗
NASA NTRS1974

The resistance to embrittlement by a hydrogen environment of selected high strength iron-manganese base alloys

Fe-16Mn and Fe-25Mn base alloys, which had been cold worked to yield strength levels of 201 and 178 KSI, were resistant to degradation of mechanical properties in a one atmosphere hydrogen environment at ambient temperature under the loading conditions employed in this investigation. Transmission electron microscopy established that bands of epsilon phase martensite and fcc mechanical twins were formed throughout the fcc matrix when these alloys were cold worked. In the cold worked alloys a high density of crystal defects were observed associated with both types of strain induced structures, which should contribute significantly to the strengthening of these alloys. High strength iron base alloys can be produced which appear to have some resistance to degradation of mechanical properties in a hydrogen environment under certain conditions.

Benson, R. B., Jr.↗
NASA NTRS1983

Mixed-mode strain-energy-release rate effects on edge delamination of composites

Unnotched graphite/epoxy laminates, designed to delaminate at the edges under static and cyclic tensile loads, were tested and analyzed. The specimen stacking sequences were chosen so that the total strain-energy-release rate, G, for edge delamination was identical for all three layups. However, each layup had different percentages of crack-opening and shear-mode strain-energy-release rates, G sub 1 and G sub 2, respectively. Results with composites made from T300 graphite fibers and 5208 epoxy, a brittle resin, indicated that only G sub 1 contributed to delamination onset under static loading. However, results with composites made from C6000 fibers and H205 epoxy, a tougher resin, indicated that the total F governed the onset of edge delaminations under cyclic loads. In addition, for both materials, the threshold level of G for delamination onset in fatigue was significantly less than the critical G sub c measured in static tests. Futhermore, although the C6000/H205 material had a much higher static G sub c than T300/5208, its fatigue resistance was only slightly better. A series of mixed-mode tests, like the ones in this study, may be needed to evaluate toughened-resin composites developed for highly strained composite structures subjected to cyclic loads.

Obrien, T. K.↗
NASA NTRS1985

High transconductance InGaAs/AlGaAs pseudomorphic modulation-doped field-effect transistors

Pseudomorphic In0.15Ga0.85As/A10.15Ga0.85As modulation-doped field effect transistors (MODFET's) exhibiting extremely good dc characteristics have been successfully fabricated. dc transconductance in these strained-layer structures of 270 mS/mm was measured for 1-micron gate, normally-on devices at 300 K. Maximum drain current levels are 290 mA/mm, with excellent pinch-off and saturation characteristics. The transconductance increased to 360 mS/mm at 77 K while no persistent photoconductivity or drain collapse was observed. Preliminary microwave results indicate a 300-K current gain cutoff frequency of about 20 GHz. These results are equivalent to the best GaAs/AlGaAs MODFET results and are due in part to the improved transport properties and carrier confinement in the InGaAs quantum well.

Ketterson, A.↗