Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface morphologies”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Crystallinity, Surface Morphology, and Photoelectrochemical Effects in Conical InP and InN Nanowires Grown on Silicon

The growth conditions of two types of indium-based III–V nanowires, InP and InN, are tailored such that instead of yielding conventional wire-type morphologies, single-crystal conical structures are formed with an enlarged diameter either near the base or near the tip. By using indium droplets as a growth catalyst, combined with an excess indium supply during growth, “ice cream cone” type structures are formed with a nanowire “cone” and an indium-based “ice cream” droplet on top for both InP and InN. Surface polycrystallinity and annihilation of the catalyst tip of the conical InP nanowires are observed when the indium supply is turned off during the growth process. This growth design technique is extended to create single-crystal InN nanowires with the same morphology. Conical InN nanowires with an enlarged base are obtained through the use of an excess combined Au–In growth catalyst. Electrochemical studies of the InP nanowires on silicon demonstrate a reduction photocurrent as a proof of photovolatic behavior and offer insight as to how the observed surface polycrystallinity and the resulting interface affect these device-level properties. Furthermore, a photovoltage is induced in both types of conical InN nanowires on silicon, which is not replicated in epitaxial InN thin films.

36 MATERIALS SCIENCE↗

Mesoporous CuFe 2 O 4 Photoanodes for Solar Water Oxidation: Impact of Surface Morphology on the Photoelectrochemical Properties**

Abstract Metal oxide‐based photoelectrodes for solar water splitting often utilize nanostructures to increase the solid‐liquid interface area. This reduces charge transport distances and increases the photocurrent for materials with short minority charge carrier diffusion lengths. While the merits of nanostructuring are well established, the effect of surface order on the photocurrent and carrier recombination has not yet received much attention in the literature. To evaluate the impact of pore ordering on the photoelectrochemical properties, mesoporous CuFe 2 O 4 (CFO) thin film photoanodes were prepared by dip‐coating and soft‐templating. Here, the pore order and geometry can be controlled by addition of copolymer surfactants poly(ethylene oxide)‐ block ‐poly(propylene oxide)‐ block ‐poly(ethylene oxide) (Pluronic® F‐127), polyisobutylene‐ block ‐poly(ethylene oxide) (PIB‐PEO) and poly(ethylene‐ co ‐butylene)‐ block ‐poly(ethylene oxide) (Kraton liquid™‐PEO, KLE). The non‐ordered CFO showed the highest photocurrent density of 0.2 mA/cm 2 at 1.3 V vs. RHE for sulfite oxidation, but the least photocurrent density for water oxidation. Conversely, the ordered CFO presented the best photoelectrochemical water oxidation performance. These differences can be understood on the basis of the high surface area, which promotes hole transfer to sulfite (a fast hole acceptor), but retards oxidation of water (a slow hole acceptor) due to electron‐hole recombination at the defective surface. This interpretation is confirmed by intensity‐modulated photocurrent (IMPS) and vibrating Kelvin probe surface photovoltage spectroscopy (VKP‐SPS). The lowest surface recombination rate was observed for the ordered KLE‐based mesoporous CFO, which retains spherical pore shapes at the surface resulting in fewer surface defects. Overall, this work shows that the photoelectrochemical energy conversion efficiency of copper ferrite thin films is not just controlled by the surface area, but also by surface order.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of LPBF Processing Parameters on Inconel 718 Lattice Structures: Geometrical Characteristics, Surface Morphology, and Mechanical Properties

Laser Powder Bed Fusion (LPBF) enables the additive manufacturing of complex lattice structures. However, the fabrication of lattice structures via LPBF poses challenges in achieving the intended geometrical accuracy due to their inherent complexity. This study investigates the effects of LPBF processing parameters, specifically laser power and scanning speed, on the geometrical characteristics, surface quality, and mechanical behavior of Inconel 718 lattices structures. The results reveal that processing parameters required for the fabrication of near-full dense structures do not translate effectively to lattice configurations, as variations in energy input influence lattice geometry and surface quality. In this work, strut thickness, open-pore size, open-cell porosity, and surface roughness were measured, and the mechanical properties of the lattices were evaluated under shear loading. The findings indicate that lower energy inputs, achieved by reducing laser power and increasing scanning speed, yield porous structures but lead to mechanical degradation. In contrast, high energy inputs lead to lattices with enhanced strength but result in undesirable open-pore blockage and dimensional inaccuracies. These findings provide insights into tailoring LPBF parameters for dimensional accuracy in lattices and correlating the processing parameters to mechanical performance and surface roughness.

36 MATERIALS SCIENCE↗

Laser Patterning of Diamond. Part I. Characterization of Surface Morphology

As the use of diamond as a material for electronic and research applications increases, methods of patterning diamond will be required. In this work, single- and polycrystalline synthetic diamond samples were exposed to laser beams of different energies, wavelengths, and pulse durations. The effects of this exposure were characterized using optical microscopy, scanning electron microscopy, and atomic force microscopy. The threshold ablation energy density for 266 nm radiation with {approx} 30 ps pulse duration was measured to be {approx} 14 J/cm{sup 2}. The threshold for {approx} 10 ns pulses at the same wavelength was similar, but the ablated area displayed larger surface damage. The surface damage and the threshold energy increase significantly for 532 and 1064 nm radiations. Ablation performed using 213 nm radiation produced the most uniform surface. Changes in the ablated surface are presented in detail.

43 PARTICLE ACCELERATORS↗

Toward Ultraflat Surface Morphologies During Focused Electron Beam Induced Nanosynthesis: Disruption Origins and Compensation

Here we explore emerging applications for nanoscale materials demand precise deposit shape retention from design to deposition. This study investigates the effects that disrupt high-fidelity shapes during focused electron beam induced nanosynthesis. It is shown that process parameters, patterning strategies and deposit topography can impose lateral precursor coverage gradients during growth resulting in unwanted topographic artifacts. The study classifies the evolving surface shapes into four general types and explains the formation and transition from a fundamental point of view. Continuum model calculations and simulations expand the experimental results to provide a comprehensive insight into understand the disruption mechanism. The findings demonstrate that the well-established concept of growth regimes has to be expanded by its lateral gradients as they strongly influence final shape fidelities. Finally, the study is complemented by a compensation strategy that improves the edge fidelity on the lower nanoscale to further push this technique toward the intrinsic limitations.

36 MATERIALS SCIENCE↗

Microstructure and surface morphology of InAsSbBi grown by molecular beam epitaxy

The physical and chemical properties of 210 nm thick InAsSbBi layers grown by molecular beam epitaxy at temperatures between 400 and 430 °C on (100) GaSb substrates are investigated using Rutherford backscattering, X-ray diffraction, transmission electron microscopy, Nomarski optical microscopy, and atomic force microscopy. The results indicate that the layers are nearly lattice matched, coherently strained, and contain dilute Bi mole fractions. Large surface droplets with diameters on the order of 1 μm and densities on the order of 106 cm−2 are observed when the InAsSbBi growth is performed with lean As overpressures around 1%. Surface droplets are not observed when the As overpressure is increased to 4%. Small crystalline droplets with diameters on the order of 70 nm and densities on the order of 1010 cm−2 are observed between the large droplets for InAsSbBi grown at 430 °C. Analysis of one of the small droplets indicates a misoriented zinc blende crystal structure composed primarily of In, Sb, and Bi, with a lattice constant of 6.543 ± 0.038 Å. Lateral modulation in the Bi mole fraction is observed in InAsSbBi layers grown at 400 °C.

Kosireddy, R. R.↗

Surface morphology of titanium dioxide (TiO{sub 2}) nanoparticles on aluminum interdigitated device electrodes (IDEs)

Titanium dioxide (TiO{sub 2}) nanoparticles based Interdigitated Device Electrodes (IDEs) Nanobiosensor device was developed for intracellular biochemical detection. Fabrication and characterization of Scanning Electron Microscopy (SEM) using IDE nanocoated with TiO{sub 2} was studied in this paper. SEM analysis was carried out at 10 kV acceleration volatege and a 9.8 mA emission current to compare IDE with and without TiO{sub 2} on the surface area. The simple fabrication process, high sensitivity, and fast response of the TiO{sub 2} based IDEs facilitate their applications in a wide range of areas. The small size of semiconductor TiO{sub 2} based IDE for sensitive, label-free, real time detection of a wide range of biological species could be explored in vivo diagnostics and array-based screening.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Chemistry and surface morphology of soil particles from Luna 20 LRL sample 22003.

Optical and scanning electron microscopy, scanning electron microprobes and energy dispersion techniques were applied in an analysis of six siliceous glass spheres, five siliceous glass-bonded agglutinates and one breccia fragment from Luna 20 sample 22003. It is theorized that local meteor impact processes might have been responsible for the formation of most of the glass spheres and that the impacts of relatively high velocity particles might have been responsible for the craters observed on the surfaces of the spheres. The concentrations of iron spherules on the surfaces of the glass spheres were generally lower than in similar Apollo 11 and 12 glass spheres.

Carter, J. L.↗

Single-pulse excimer laser nanostructuring of silicon: A heat transfer problem and surface morphology

We present computer modeling along with experimental data on the formation of sharp conical tips on silicon-based three-layer structures that consist of a single-crystal Si layer on a 1 {mu}m layer of silica on a bulk Si substrate. The upper Si layers with thicknesses in the range of 0.8-4.1 {mu}m were irradiated by single pulses from a KrF excimer laser focused onto a spot several micrometers in diameter. The computer simulation includes two-dimensional time-dependent heat transfer and phase transformations in Si films that result from the laser irradiation (the Stefan problem). After the laser pulse, the molten material self-cools and resolidifies, forming a sharp conical structure, the height of which can exceed 1 {mu}m depending on the irradiation conditions. We also performed computer simulations for experiments involving single-pulse irradiation of bulk silicon, reported by other groups. We discuss conditions under which different types of structures (cones versus hollows) emerge. We confirm a correlation between the presence of the lateral resolidification condition after the laser pulse and the presence of conical structures on a solidified surface.

36 MATERIALS SCIENCE↗

Surface morphology evolution of m-plane (1100) GaN during molecular beam epitaxy growth: Impact of Ga/N ratio, miscut direction, and growth temperature

We present a systematic study of morphology evolution of [1100] m-plane GaN grown by plasma-assisted molecular beam epitaxy on free-standing m-plane substrates with small miscut angles towards the -c [0001] and +c [0001] directions under various gallium to nitrogen (Ga/N) ratios at substrate temperatures T = 720 Degree-Sign C and T = 740 Degree-Sign C. The miscut direction, Ga/N ratio, and growth temperature are all shown to have a dramatic impact on morphology. The observed dependence on miscut direction supports the notion of strong anisotropy in the gallium adatom diffusion barrier and growth kinetics. We demonstrate that precise control of Ga/N ratio and substrate temperature yields atomically smooth morphology on substrates oriented towards +c [0001] as well as the more commonly studied -c [0001] miscut substrates.

36 MATERIALS SCIENCE↗

In Situ Studies of Methanol Decomposition Over Cu(111) and Cu2O/Cu(111): Effects of Reactant Pressure, Surface Morphology, and Hot Spots of Active Sites

The dissociative adsorption of methanol was investigated on Cu(111) and ultrathin Cu 2 O films. We employed synchrotron-based Ambient Pressure X-ray Photoelectron Spectroscopy (AP-XPS) and Scanning Tunneling Microscopy (STM) to study the dynamics of gas–solid interactions, and calculations based on Density Functional Theory (DFT) were used to examine the reaction path. C 1s XPS spectra revealed that methanol underwent dissociative adsorption on plain Cu(111) to form methoxy (CH 3 O), formaldehyde (H 2 CO), and formate (HCOO) at a pressure range of 0.5–10 mTorr, with these species remaining on the surface after evacuation. This was accompanied by the appearance of a low coverage (~0.05 ML) of O ads in the O 1s which can be considered a highly active site for methanol activation. The high activity is apparent by a coverage of 0.8 ML of methoxy at room temperature. STM was unable to image these species at room temperature as they were highly mobile on metallic copper. In contrast, for CH 3 OH on Cu 2 O/Cu(111), STM showed clear hot spots for reaction and a complex array of adsorption structures. On the oxide substrate, there was decomposition of methanol to H 2 CO, CH 3 O, HCOO, and hydrocarbon species (CH x ) due to the subsequent interactions of methanol with lattice oxygen. Cu(111) remained entirely saturated with decomposition products under 10 mTorr of methanol (θ ≈ 0.97 ML), whereas the Cu 2 O overlayer was saturated at a much lower coverage (θ ≈ 0.30 ML). STM revealed rows and step edges of Cu 2 O decorated with decomposition products and metallic Cu islands ~5 nm in size. The difference in activity between Cu(111) and Cu 2 O/Cu(111) is attributed to the significant amount of O present on the oxide surface. Additionally, Density Functional theory (DFT) calculations described the XPS measurements well, showing a likely methanol dissociation to *CH 3 O and therefore a surface reduction. More importantly, the DFT results revealed that it was the chemisorbed oxygen on Cu 2 O/Cu(111) which oxidized the dissociated *CH 3 O to *HCOO and eventually CO 2 , while the reaction only involving upper oxygen on the Cu 2 O hexagonal ring led to the formation of H 2 CO.

36 MATERIALS SCIENCE↗

Corrigendum and Addendum: Helium flux effects on bubble growth and surface morphology in plasma-facing tungsten from large-scale molecular dynamics simulations (2019 Nucl. Fusion 59 066035)

Two of the simulations discussed in a prior article (Hammond et al 2019 Nucl. Fusion 59 066035) were affected by a simulation glitch. We repeated the affected calculations and discuss them here. Here, the overall conclusions are essentially unchanged, though the details are different. In particular, observations that we referred to as ‘concerted bursting’ were caused primarily by non-physical heating and cooling applied by the thermostat after most atoms’ velocities were deleted (for reasons that are not known for certain). The phenomenon of one bubble bursting and causing another nearby bubble to burst does exist, though its effects are much less spectacular in the absence of non-physical driving forces. The observation of an interconnected network of sub-surface cavities formed by burst bubbles is real, and the observation of holes on the surface 1–2 nm in diameter is also confirmed.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Behavior of deuterium retention and surface morphology for VPS–W/F82H

The deuterium (D) retention for Vacuum Plasma Spray (VPS)–tungsten (W)/F82H was studied using two different implantation methods, namely D plasma exposure and View the MathML source implantation. The D retention for polished VPS–W/F82H after plasma exposure was found to be reduced compared to that for polycrystalline tungsten. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) observations indicated that porous structures around grain boundaries and the interface between VPS–W layers would be potential D diffusion paths, leading to low D retention. In the case of View the MathML source implantation, the shape of D2 TDS spectrum was almost the same as that for D plasma-exposed VPS–W/F82H; however, the D retention was quite high for unpolished VPS–W/F82H, indicating that most of D was trapped by the oxide layer, which was produced by the VPS process. The reduction of surface area due to the polishing process also reduces D retention for VPS–W/F82H. These results indicate that controlling the surface chemical states is important for the reduction of tritium retention for future fusion reactors.

99 GENERAL AND MISCELLANEOUS↗

Effects of cation stoichiometry on surface morphology and crystallinity of ZnGeN 2 films grown on GaN by metalorganic chemical vapor deposition

ZnGeN 2 films were grown on GaN-on-sapphire templates via metalorganic chemical vapor deposition. Energy dispersive X-ray spectroscopy was used to estimate the Zn/(Zn+Ge) composition ratio in the films. This ratio decreased with increase in growth temperature but increased with increase in total reactor pressure or Zn/Ge precursor flow rate ratio. Systematic mapping of these key growth parameters has allowed us to identify the growth window to achieve ZnGeN 2 with stoichiometric cation composition. Compositional and statistical analyses performed on data acquired from atom probe tomography provided insight into the local compositional homogeneity. The cations Zn and Ge did not demonstrate segregation or clustering at the sub-nanometer level. Based on X-ray diffraction 2θ-ω scan profiles and transmission electron microscope nano-diffraction patterns, the films with near-stoichiometric cation ratios were single crystalline with planar surfaces, whereas zinc-rich or zinc-poor films were polycrystalline with nonplanar surfaces. The growth direction of the single crystalline ZnGeN 2 films on GaN templates was along the c-axis. Room temperature Raman spectra showed features associated with the phonon density of states, indicating the presence of cation disorder in the lattice. A cathodoluminescence peak associated with transitions involving deep level defects was observed around 640 nm. The intensity of this peak increased by almost 2.5 times as the temperature was reduced to 77 K from room temperature. A similar peak was observed in photoluminescence spectra collected at 80 K.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Studies of surface morphology and optical properties of ZnO nanostructures grown on different molarities of TiO{sub 2} seed layer

Titanium dioxide (TiO{sub 2}) seed layer was prepared by using sol-gel spin-coating technique, followed by growth of 0.01 M of Zinc oxide (ZnO) nanostructures by solution-immersion. The molarities of TiO{sub 2} seed layer were varied from 1.1 M to 0.100 M on glass substrates. The nanostructures thin films were characterized by Field Emission Scanning Electrons Microscope (FESEM), Photoluminescence (PL) spectroscopy and Ultraviolet-Visible (UV-Vis) spectroscopy. FESEM images demonstrate that needle-like ZnO nanostructures are formed on all TiO{sub 2} seed layer. The smallest diameter of needle-like ZnO nanostructures (90.3 nm) were deposited on TiO{sub 2} seed layer of 0.100 M. PL spectra of the TiO{sub 2}: ZnO nanostructures thin films show the blue shifted emissions in the UV regions compared to the ZnO thin film. Meanwhile, UV-vis spectra of films display high absorption in the UV region and high trasparency in the visible region. The highest absorbance at UV region was recorded for sample which has 0.100 M of TiO{sub 2} seed layer.

77 NANOSCIENCE AND NANOTECHNOLOGY↗