Search NASA⌕ Search

SEARCH · Search NASA

Results for “technical levels”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Vision of 3D printing with concrete ÔÇö Technical, economic and environmental potentials

A vision is presented on 3D printing with concrete, considering technical, economic and environmental aspects. Although several showcases of 3D printed concrete structures are available worldwide, many challenges remain at the technical and processing level. Currently available high-performance cement-based materials cannot be directly 3D printed, because of inadequate rheological and stiffening properties. Active rheology control (ARC) and active stiffening control (ASC) will provide new ways of extending the material palette for 3D printing applications. From an economic point of view, digitally manufactured concrete (DFC) will induce changes in the stakeholders as well as in the cost structure. Although it is currently too ambitious to quantitatively present the cost structure, DFC presents many potential opportunities to increase cost-effectiveness of construction processes. The environmental impact of 3D printing with concrete has to be seen in relation to the shape complexity of the structure. Implementing structural optimization as well as functional hybridization as design strategies allows the use of material only where is structurally or functionally needed. This design optimization increases shape complexity, but also reduces material use in DFC. As a result, it is expected that for structures with the same functionality, DFC will environmentally perform better over the entire service life in comparison with conventionally produced concrete structures.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Optimal Voltage Control in Low-Observable Unbalanced Distribution Systems

The increased integration of distributed energy resources (DERs) in distribution systems brings both advantages and technical challenges. High levels of DERs can often cause over/under voltage problems. Classical voltage control algorithms are based on full knowledge of voltage states across all nodes in the system. However, this may not be a practical assumption since many locations in distribution systems are unobservable. Therefore, this paper proposes a new model predictive control (MPC) based control algorithm that accounts for system unobservability to efficiently eliminate voltage violations with as low as 50% fraction of observable nodes. Additionally, an analytical voltage sensitivity framework is employed to quickly determine the change in voltage states due to PV injections. The effectiveness of the proposed method is validated via simulations on the unbalanced IEEE 37 node test system.

Abujubbeh, Mohammad↗

Play Fairway Analysis Retrospective GeoRePORTs

NREL, as part of the Play Fairway Analysis (PFA) Retrospective and with assistance from PFA PIs, completed GeoRePORTs for the sites identified in Phases 1&2 of the DOE PFA projects. The GeoRePORT (geothermal resource portfolio optimization and reporting technique) uses two factors to describe a specific project; grade and project readiness level. Grade describes the quality or potential of a project while project readiness level shows the progress of research and development. The categories that factor into the total grades and readiness levels are Geological, Technical, and Socio-Economic.

15 GEOTHERMAL ENERGY↗

NEXT GENERATION SOLVENT MATERIALS COMPATIBILITY WITH POLYMER COMPONENTS WITHIN MODULAR CAUSTIC-SIDE SOLVENT EXTRACTION UNIT

The Office of Waste Processing, within the Office of Technology Innovation and Development, is funding the development of an enhanced solvent for deployment at the Savannah River Site for removal of cesium from High Level Waste. The technical effort is collaboration between Oak Ridge National Laboratory (ORNL), Savannah River National Laboratory (SRNL), and Argonne National Laboratory. The first deployment target for the technology is within the Modular Caustic-Side Solvent Extraction Unit (MCU). Deployment of a new chemical within an existing facility requires verification that the chemical components are compatible with the installed equipment. In the instance of a new organic solvent, the primary focus is on compatibility of the solvent with organic polymers used in the facility. This report provides the data from exposing these polymers to the Next Generation Solvent (NGS). The test was conducted over six months. An assessment of the dimensional stability of polymers present in MCU (i.e., PEEK, Grafoil{reg_sign}, Tefzel{reg_sign} and Isolast{reg_sign}) in the modified NGS (where the concentration of the guanidine suppressor and MaxCalix was varied systematically) showed that guanidine (LIX{reg_sign}79) selectively affected Tefzel{reg_sign} (by an increase in size and lowering its density). The copolymer structure of Tefzel{reg_sign} and possibly its porosity allows for the easier diffusion of guanidine. Tefzel{reg_sign} is used as the seat material in some of the valves at MCU. Long term exposure to guanidine, may make the valves hard to operate over time due to the seat material (Tefzel{reg_sign}) increasing in size. However, since the physical changes of Tefzel{reg_sign} in the improved solvent are comparable to the changes in the CSSX baseline solvent, no design changes are needed with respect to the Tefzel{reg_sign} seating material. PEEK, Grafoil{reg_sign} and Isolast{reg_sign} were not affected by guanidine and MaxCalix within six months of exposure. The initial rapid weight gain observed in every polymer is assigned to the finite and limited uptake of Isopar{reg_sign} L/Modifier by the polymers probably due to the polymers porosity and rough surfaces. Spectroscopic data on the organic liquid and the polymer surfaces showed no preferential adsorption of any component in the NGS to the polymers and no leachate was observed in the NGS from any of the polymers studied.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Next Generation Solvent – Materials Compatibility with Polymer Components within Modular CausticSide Solvent Extraction Unit (Final Report)

The Office of Waste Processing, within the Office of Technology Innovation and Development, is funding the development of an enhanced solvent for deployment at the Savannah River Site for removal of cesium from High Level Waste. The technical effort is collaboration between Oak Ridge National Laboratory (ORNL), Savannah River National Laboratory (SRNL), and Argonne National Laboratory. The first deployment target for the technology is within the Modular Caustic-Side Solvent Extraction Unit (MCU). Deployment of a new chemical within an existing facility requires verification that the chemical components are compatible with the installed equipment. In the instance of a new organic solvent, the primary focus is on compatibility of the solvent with organic polymers used in the facility. This report provides the data from exposing these polymers to the Next Generation Solvent (NGS). The test was conducted over six months. An assessment of the dimensional stability of polymers present in MCU (i.e., PEEK, Grafoil, Tefzel and Isolast) in the modified NGS (where the concentration of LIX®79 and MaxCalix was varied systematically) showed that LIX®79 selectively affected Tefzel and its different grades (by an increase in size and lowering its density). The copolymer structure of Tefzel and possibly its porosity allows for the easier diffusion of LIX®79. Tefzel is used as the seat material in some of the valves at MCU. Long term exposure to LIX®79, may make the valves hard to operate over time due to the seat material (Tefzel) increasing in size. However, since the physical changes of Tefzel in the improved solvent are comparable to the changes in the CSSX baseline solvent, no design changes are needed with respect to the Tefzel seating material. PEEK, Grafoil and Isolast were not affected by LIX®79 and MaxCalix within six months of exposure. The initial rapid weight gain observed in every polymer is assigned to the finite and limited uptake of Isopar® L/Modifier by the polymers probably due to the polymers porosity and rough surfaces. Spectroscopic data on the organic liquid and the polymer surfaces showed no preferential adsorption of any component in the NGS to the polymers and with the exception of CPVC, no leachate was observed in the NGS from any of the polymers studied. The testing shows no major concerns for compatibility over the short duration of these tests but does indicate that longer duration exposure studies are warranted, especially for Tefzel. However, the physical changes experienced by Tefzel in the improved solvent were comparable to the physical changes obtained when Tefzel is placed in CSSX baseline solvent. Therefore, there is no effect of the improved solvent beyond those observed in CSSX baseline solvent.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Report on fact finding visit to Texas A&M Cyclotron Institute

I am actively investigating how to form a larger collaboration that will include Texas A&M as a key partner. The Institute currently has thousands of hours of beam time available for experiments per year. The facility is well staffed at the technical and engineering levels and hosts a large complement of undergraduate students, graduate students and post-doctoral researchers. I have also discovered that the NNSA has a matching program to help foster University-LLNL partnerships. There is currently up to $125k of matching funds available at LLNL available for collaborative research. A Texas A&M-LLNL collaboration would allow us to build a strong pipeline of students and researchers into the NNSA laboratories. We would also be able to have multiple students, post-docs and researchers involved and potentially lead some of the many experiments we need done to perform for our research programs.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

We Are Hiring

At Los Alamos you get an internship customized to your skill level. You receive technical mentoring and professional skill-building opportunities. This is all while working on exciting physics problems. The result? Valuable hands-on experience to help you make decisions about your future. Physics Division can help you expand your horizons, whether you are an undergraduate or graduate student seeking a one-of-a-kind summer internship experience or a post-bachelor’s or post-master’s student ready to hone your experimental research skills.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Austin Sustainable and Holistic Integration of Energy Storage and Solar PV [Austin SHINES]. Final Report, Version 2

The Austin SHINES project and solution is a software management platform, for an electric grid with a high penetration of dispersed photovoltaic (PV) solar generation sites, which maintains the traditional power quality and reliability associated with grid service. This project developed and deployed the platform as a Distributed Energy Resource Management System (DERMS), engaging multiple advanced controls, to evaluate operation and optimization of a fleet of diverse DER assets, installed at several locations among Austin Energy’s customers and distribution system. The project also produced a methodology to create a replicable DERMS template, adaptable to other regions and market structures. Last, Austin SHINES aimed to demonstrate the solution’s methodology would enable the DER grid ecosystem to serve load at a technical cost (System Levelized Cost of Electricity, or System LCOE) of less than the U.S. Department of Energy SHINES program metric of $0.14/kWh, in a defined boundary, while enabling a high penetration of distributed PV. Research was categorized in 6 reports (Final Deliverables = FD) listed below, with titles and descriptions indicating which area of understanding was investigated: FD-1: System Levelized Cost of Electricity (System LCOE) Methodology The creation and use of the System LCOE to Serve Load metric that encompasses the holistic, system-level costs and benefits of all resources, and enables them to be evaluated based on their ability to support an efficient and low-cost integrated grid ecosystem. FD-2: Software Platform Product Description The creation of new DER control methodologies deployable within a utility-grade software platform that enable DER's to maximize their benefit within a grid, that is capable of serving load enabling a high penetration of distributed PV generation. FD-3: Optimal Design Methodology Optimal design methodologies for individual DER installations that enable utilities to determine the optimal combinations and sizing for individual DER sites. FD-4: Austin SHINES Ownership and Operation Models for DER System Performance A comparison of multiple DER aggregation and ownership methodologies including direct utility control, third-party aggregator, and autonomous. FD-5: Economic Modeling & Optimization A comparison of multiple DER technology mixes and configurations within the distribution system, providing insight into an optimal blend of technologies that best enable the distribution system to serve load at the lowest cost at high penetrations of solar. FD-6: Fielded Assets Deployed DER assets within the Austin Energy SHINES circuits. Austin SHINES provided an opening for state-of-the-art technology products to be deployed, providing a rich opportunity for improving how each of the products perform as stand-alone products, and in concert with other complementary products. The Austin SHINES project comprised of two key metrics for System LCOE: SystemLCOE_SHINES<$0.14/kWh Modeled ΔSystemLCOE_SHINES/ΔSystemLCOE_Base≥20% at same solar penetration The System LCOE calculation uses the costs of the utility-owned infrastructure as it exists today, the cost of the DERs that exist in the system today, and the cost of the purchase of energy from ERCOT wholesale markets over the course of the calendar year. All costs are on an annualized basis. The capital and operating costs are derived from the rate case, which produces a yearly cost. The net cost of energy and services imported to the system is integrated over the test year, as is the load served and solar penetration. The first metric was easily achieved by every scenario considered. The goal was set when the Department of Energy’s SHINES Funding Opportunity Announcement was written in 2015 and was a more difficult target at the time. Due mostly to rapidly declining costs for DERs and the significant decrease in the Electric Reliability Council of Texas (ERCOT) energy market prices, which results in lower net cost of energy purchases, the System LCOE is well below this target for all scenarios considered. A fleet of DERs can assume different mixtures, each of which serves the load at a different LCOE. The optimal mixture of DERs serves load at the smallest System LCOE. The second metric (hereinafter %delta metric) asks that the holistic DERMS controls reduce the incremental cost above the baseline of going to a high solar penetration future by at least 20% as compared to the case of a DER deployment with no sophisticated controls (autonomous). Many comparison sets were created throughout this project. Physical technology was installed for informing utility engineering and testing several types of operational control schemes, through the DERMS. The types of operational control which were compared for valuation of the System LCOE Metric were: Holistic control = using the full suite of the DERMS platform to decide and optimize how/why the systems operate depending on weather, market, and reliability signal input. Autonomous control = a local mode at the asset site, wherein a schedule operates the asset, with visibility into performance only No control = the baseline for comparing value against the other two types of control The types of ownership control included: Direct Utility control = the utility dispatches a signal to each asset Third-Party Aggregator = a third party aggregates a fleet of assets and the utility dispatches one signal for all Autonomous = a local mode is set for operation at the asset site, wherein a schedule operates the asset, with visibility into performance only The types of control methodologies deployable within a utility-grade software platform included: Utility Peak Load Reduction = Lower transmission cost obligation Day-Ahead Energy Arbitrage = Realize economic value through price differential Real-Time Price Dispatch = Realize economic value from real-time price spikes Voltage support = Reduce losses and increase solar generation Distribution Congestion Management = Increase local grid reliability Demand Charge Reduction = Lower customer bills and realize system benefit The fielded assets deployed for the project were: Utility Scale Kingsbery Energy Storage System: 1.5 MW / 3 MWh Li-Ion battery storage Mueller Energy Storage System: 1.75 MW / 3.2 MWh Li-Ion battery storage, 7 Energy Storage Units (250 kW each) La Loma Community Solar: 2.6 MW Commercial Scale Aggregated storage installations at 3 sites, with existing solar (300+ kW): One 18 kW / 36 kWh Li-Ion battery storage Two 72 kW / 144 kWh Li-Ion battery storage Residential Scale Aggregated storage installations: -Six stationary battery storage systems (10 kWh each) at homes with existing solar -One Electric Vehicle installed as Vehicle-to-Grid (V2G) Utility-Controlled Solar via Smart Inverters at 12 homes Autonomously-Controlled Smart Inverters at 6 homes Over the course of the project, Austin SHINES undertook installing more than 3 MW of distributed battery energy storage, smart PV inverters, a DER control platform, and other enabling technologies utilizing customer and utility locations and aggregation models. All of these resources were to be integrated and optimized at the utility level. DER assets and control methodologies were designed to achieve a credible pathway to a System LCOE for energy delivered to load of $0.14//kWh or less by 2020, while maximizing distributed solar generation and maintaining acceptable standards of power quality. The project also established a template for other regions to follow, to maximize the adoption of distributed solar PV in support of an economic and efficient grid. In total, the Austin SHINES project added value to the DER subject area in each layer of integration. From utility, to commercial to residential scales, the sheer hierarchy of communication and coordination was a significant accomplishment in addition to learnings from what these communications revealed was unique to each. Economically, the most effective method demonstrated was the criticality of planning phases. Contingencies and multiple projection scenarios helped guide the project to deploy optimal design as close as feasible, in real world conditions. The project and reports will serve public benefit by outlining specific areas of DER strategy and installation where many stakeholders and needs can be addressed with improved efficiency. Overall, communities and utilities should use the results to guide the increasing options available for powering the grid with DER, renewables, and carbon considerate energy.

14 SOLAR ENERGY↗

Assessment of the Dominican Republic’s Commercial and Industrial Scale Energy Efficiency Sector

In this paper the National Renewable Energy Laboratory (NREL) explores the commercial and industrial (C&I) energy efficiency market in the Dominican Republic, including the market’s current status. During NREL’s engagement with its Dominican counterparts, NREL noted market gaps, identified by both public and private sector market actors, that became the focus of this report. The intent is two-fold. First, to assist potential customers, project financing institutions, and various government agencies understand where the energy efficiency sector stands, in August 2020. Second to help them recognize the scope, scale, and opportunity for energy savings from untapped potential large reductions in energy expenditures. This research identified how savings could be captured through improvements to the enabling environment, technical capacity, and level of activity in the sector. Moreover, it determined that through taking action to catalyze energy efficiency investment, the government could make significant progress towards its self-declared NDC goals, and result in tens of millions of dollars in savings across the Dominican economy for both the private and public sectors.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Embedding Agile Practices within a Plan-Driven Hierarchical Project Life Cycle

Organizations use structured, plan-driven approaches to provide continuity, direction, and control to large, multi-year programs. Projects within these programs vary greatly in size, complexity, level of maturity, technical risk, and clarity of the development objectives. Organizations that perform exploratory research, evolutionary development, and other R&D activities can obtain the benefits of Agile practices without losing the benefits of their program’s overarching plan-driven structure. This paper describes application of Agile development methods on a large plan-driven sensor integration program. While the client employed plan-driven, requirements flow-down methodologies, tight project schedules and complex interfaces called for frequent end-to-end demonstrations to provide feedback during system development. The development process maintained the many benefits of plan-driven project execution with the rapid prototyping, integration, demonstration, and client feedback possible through Agile development methods. This paper also describes some of the tools and implementing mechanisms used to transition between and take advantage of each methodology, and presents lessons learned from the project management, system engineering, and developer’s perspectives.

Agile Development↗

Algorithm for Establishing Safeguards Termination Concentration Limits

This paper presents an algorithm for estimating the maximum concentration limits for terminating safeguards on nuclear materials. These limits are important because such material is no longer subject to accounting, reporting or inspections after the International Atomic Energy Agency (IAEA) has approved the termination of safeguards on nuclear material declared by a State to be waste.Maximum concentration limits for different waste forms generated within nuclear fuel cycle facilities must be sufficiently conservative such that termination of safeguards does not become a weak link in the safeguards system. The concentration limits must also remain practical in order to ensure IAEA resources are used effectively and efficiently to implement safeguards in the State. These termination limits should be technically-based while remaining objective and reasonable to implement by the State. In support of the original IAEA guidance on concentration limits for termination of safeguards prepared in the early 1990s, the U.S. developed an algorithm to estimate concentrations that would make recovery of nuclear material from waste on which safeguards had been terminated at least as unattractive as undeclared production from uranium ore or diversion of similar nuclear material. In 2016, the IAEA sought technical advice from a meeting of experts from selected member States to support updating its internal guidance on termination of safeguards. Their recommendations included extending the guidance to consider additional waste forms. The experts in the 2016 meeting recommended that the IAEA limits should more clearly reflect the technical difficulty and level of effort required to recover nuclear material from the various waste forms. This paper identifies and assesses the most likely techniques a State might use to recover nuclear material from the waste forms identified by the experts and determines how the safeguards termination algorithm could be revised to more accurately reflect the difficulty of recovering one significant quantity of nuclear material from these waste forms.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

University of Nevada, Reno Graduate Certificate in Nuclear Packaging

This paper describes a new Graduate Certificate in Nuclear Packaging (GCNP). Nuclear materials are currently used for large-scale production of electricity without greenhouse gas generation, advanced medical treatments, food sterilization, and sophisticated measurement technologies. In order to benefit from these uses, nuclear materials packaging must be developed, manufactured, inspected, and maintained for storage, transfer, transport, and disposal that protect the public and the environment. The U.S. Department of Energy (DOE) Packaging Certification Program (PCP) originally offered the following ten, one-day to ten-day training courses. 1. Methods for Reviewing Safety Analysis Reports for Packages and Performing Confirmatory Analysis; 2. Welding Criteria for Shipping Containers; 3. Structural Analysis and Acceptance Criteria; 4. Quality Assurance (QA) for Radioactive Material Packaging Training; 5. Application of the American Society of Mechanical Engineers (ASME) Code to Radioactive Material Transportation Packaging; 6. ARG-US Radio Frequency Identification (RFID) System for Management of Nuclear and Radioactive Materials; 7. Packaging Operations and Maintenance; 8. Packaging Leakage Test Training; 9. Management of SARP Preparation; 10. Transport Security of Radioactive Material. These courses were designed in accordance with DOE standards. They were taught at a rigorous graduate-university level by experienced technical staff who are coordinated by Argonne, Lawrence Livermore, and Savannah River National Laboratories. The courses were taught at these Laboratories or nearby locations. The PCP courses are attended by personnel from government agencies, national laboratories, and the nuclear industry, from both inside and outside the United States. Students in these classes have generally earned undergraduate or higher degrees. These courses are designed to assist student with specialized job duties, and may provide them a competitive advantage when seeking employment or promotion in the nuclear packaging and other related fields. (authors)

36 MATERIALS SCIENCE↗

Conceptual Design of Decontamination System for Radioactive Contaminated Water with Microalgae

In 2011, Fukushima nuclear power plant accident in Japan caused contamination of lakes and rivers due to radioactive materials released. As time passes, the radioactivity of radioactive contaminated water has been lowered, but there is still some level of radioactive contamination. At present, decontamination of radioactive contaminated water uses a method of removing radioactive materials in polluted water by using resin or filter. This conventional decontamination method can lower the radioactive concentration of contaminated water to a certain level. However, it is difficult to reduce the amount of contaminated water to a level lower than the very low level due to technical and economic reasons. In this study, we propose a method to decontaminate water contaminated with radioactive materials using microalgae. In addition, a system for the treatment of radioactive contaminated water using microalgae has been conceptually designed.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

National Modeling of Geothermal District Energy Systems with Ambient-Temperature Loops Using dGeo: Preprint

Geothermal district energy systems (DES) with ambient-temperature loops, also known as thermal energy networks, are one option for decarbonizing space heating and cooling loads. Geothermal fifth-generation DES include an "ambient" temperature thermal loop that connects heat pumps at each building with thermal balancing sources such as geothermal borehole fields. Heating and cooling are provided via a water-source heat pump at each end-user. This project seeks to analyze the nationwide potential for ambient-temperature loop districts by creating a new module within the Distributed Geothermal Market Demand Model (dGeo). dGeo is an agent-based modeling tool for distributed geothermal resources; it can investigate potential on a nationwide or statewide scale using geospatial data for all 50 states and thermal demands for existing buildings. This process allows for high-level estimates of technical and economic potential for ambient-temperature loop districts across the United States. Using GHEDesigner, a lookup table was created to size borehole fields for different thermal loads and ground conditions experienced across the country. A cost and financing structure, along with incentives, were applied. Cost estimates include costs for the distribution network, borehole field installation and operation, and circulation pump operation, while savings are calculated based on agent energy bills. This newly developed module can be used for assessing which areas of the country have the highest potential for agent benefits from ambient-temperature loop installation and assess the impact of different costing and pricing future scenarios. While the code is still under development and nationwide simulations are ongoing, initial results for two states are provided. Future work includes expanding the module to consider mixed residential and commercial districts and considering multiple costing scenarios.

ambient temperature loop↗

National Modeling of Geothermal District Energy Systems with Ambient-Temperature Loops Using dGeo

Geothermal district energy systems (DES) with ambient-temperature loops, also known as thermal energy networks, are one option for decarbonizing space heating and cooling loads. Geothermal fifth-generation DES include an "ambient" temperature thermal loop that connects heat pumps at each building with thermal balancing sources such as geothermal borehole fields. Heating and cooling are provided via a water-source heat pump at each end-user. This project seeks to analyze the nationwide potential for ambient-temperature loop districts by creating a new module within the Distributed Geothermal Market Demand Model (dGeo). dGeo is an agent-based modeling tool for distributed geothermal resources; it can investigate potential on a nationwide or statewide scale using geospatial data for all 50 states and thermal demands for existing buildings. This process allows for high-level estimates of technical and economic potential for ambient-temperature loop districts across the United States. A lookup table was created using GHEDesigner to size borehole fields for different thermal loads and ground conditions experienced across the country. A cost and financing structure, along with incentives, were applied. Cost estimates include costs for the distribution network, borehole field installation and operation, and circulation pump operation, while savings are calculated based on energy bills for building owners (agents). This newly developed module can be used for assessing which areas of the country have the highest potential for agent benefits from ambient-temperature loop installation and assess the impact of future cost and price scenarios. Initial results for statewide analysis (for Vermont) and nationwide (for United States) are provided. Future work includes expanding the module to consider mixed residential and commercial districts as well as evaluating multiple cost scenarios.

ambient-temperature loop↗

REACTOR PHYSICS MODELING OF SPENT NUCLEAR RESEARCH REACTOR FUEL FOR SNM ATTRIBUTION AND NUCLEAR FORENSICS

Nuclear research reactors are the least safeguarded type of reactor; in some cases this may be attributed to low risk and in most cases it is due to difficulty from dynamic operation. Research reactors vary greatly in size, fuel type, enrichment, power and burnup providing a significant challenge to any standardized safeguard system. If a whole fuel assembly was interdicted, based on geometry and other traditional forensics work, one could identify the material's origin fairly accurately. If the material has been dispersed or reprocessed, in-depth reactor physics models may be used to help with the identification. Should there be a need to attribute research reactor fuel material, the Savannah River National Laboratory would perform radiochemical analysis of samples of the material as well as other non-destructive measurements. In depth reactor physics modeling would then be performed to compare to these measured results in an attempt to associate the measured results with various reactor parameters. Several reactor physics codes are being used and considered for this purpose, including: MONTEBURNS/ORIGEN/MCNP5, CINDER/MCNPX and WIMS. In attempt to identify reactor characteristics, such as time since shutdown, burnup, or power, various isotopes are used. Complexities arise when the inherent assumptions embedded in different reactor physics codes handle the isotopes differently and may quantify them to different levels of accuracy. A technical approach to modeling spent research reactor fuel begins at the assembly level upon acquiring detailed information of the reactor to be modeled. A single assembly is run using periodic boundary conditions to simulate an infinite lattice which may be repeatedly burned to produce input fuel isotopic vectors of various burnups for a core level model. A core level model will then be constructed using the assembly level results as inputs for the specific fuel shuffling pattern in an attempt to establish an equilibrium cycle. The core level results may then be compared to the radiochemistry results from the dissolved fuel samples and a decision whether further more in-depth modeling should be performed. The SRNL is in the process of analyzing multiple research reactor fuels to determine the best means to provide forensic data for attribution and assess codes and modeling methods for attribution. As several fuel samples are analyzed, this work will allow improved SNM forensics of spent research reactor fuel. This will enable the establishment of a research reactor fuel database of SNM materials, and allow an attempt of an inverse analysis if research reactor material is diverted and seized.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Floating Photovoltaic Systems: Assessing the Technical Potential of Photovoltaic Systems on Man-Made Water Bodies in the Continental United States

We report that floating photovoltaic (FPV) systems, also called floatovoltaics, are a rapidly growing emerging technology application in which solar photovoltaic (PV) systems are sited directly on water. The water-based configuration of FPV systems can be mutually beneficial: Along with providing such benefits as reduced evaporation and algae growth, it can lower PV operating temperatures and potentially reduce the costs of solar energy generation. Although there is growing interest in FPV, to date there has been no systematic assessment of technical potential in the continental United States. We provide the first national-level estimate of FPV technical potential using a combination of filtered, large-scale datasets, site-specific PV generation models, and geospatial analytical tools. We quantify FPV co-benefits and siting considerations, such as land conservation, coincidence with high electricity prices, and evaporation rates. Our results demonstrate the potential of FPV to contribute significantly to the U.S. electric sector, even using conservative assumptions. A total of 24?419 man-made water bodies, representing 27% of the number and 12% of the area of man-made water bodies in the contiguous United States, were identified as being suitable for FPV generation. FPV systems covering just 27% of the identified suitable water bodies could produce almost 10% of current national generation. Lastly, many of these eligible bodies of water are in water-stressed areas with high land acquisition costs and high electricity prices, suggesting multiple benefits of FPV technologies.

14 SOLAR ENERGY↗