Search NASA⌕ Search

SEARCH · Search NASA

Results for “thin oxide”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Thin-film temperature sensor.

A new device has been developed for sensing small and rapid temperature changes accompanying biochemical reactions. The active element consists of an evaporated thin-film capacitor having a relatively strong temperature dependence. This dependence is derived from electron trapping effects in the thin amorphous dielectric film. A voltage output of at least 50 mV/deg can be obtained prior to amplification by using a resonant ac bridge circuit operating at 100 kHz. The corresponding noise output for a 10 kHz bandwidth can with an optimum circuit be as low as 4 microvolts. Therefore, the minimum detectable temperature change would be 80 microdegrees at 10 kHz. Rapid thermal response is assured by supporting the thin-film capacitor on a thin anodic tantalum oxide film suspended across an electrolytically etched window in a tantalum foil.

Maserjian, J.↗
NASA NTRS1974

The chemisorption of H2O, HCOOH and CH3COOH on thin amorphous films of Al2O3

Investigation of the irreversible chemisorption of water, formic acid and acetic acid on a thin amorphous aluminum oxide film, using inelastic tunneling spectroscopy. All of the tunnel junctions employed were Al-Al2O3-Pb junctions with the adsorbate on the Al2O3 surface between the Al2O3 and the Pb electrode. The results obtained include the finding that all Al2O3 surfaces prepared by oxidation of Al have free CH groups present on them.

Lewis, B. F.↗
NASA NTRS1977

High efficiency thermionic converter studies

Research in thermionic energy conversion technology is reported. The objectives were to produce converters suitable for use in out of core space reactors, radioisotope generators, and solar satellites. The development of emitter electrodes that operate at low cesium pressure, stable low work function collector electrodes, and more efficient means of space charge neutralization were investigated to improve thermionic converter performance. Potential improvements in collector properties were noted with evaporated thin film barium oxide coatings. Experiments with cesium carbonate suggest this substance may provide optimum combinations of cesium and oxygen for thermionic conversion.

Huffman, F. N.↗
NASA NTRS1978

The meaning of desert color in earth orbital photographs

The color of desert surfaces as seen in earth orbital photographs is indicative of soil composition. Apollo-Soyuz photographs of the Sturt and Simpson Deserts of Australia confirm that sand grains become redder as the distance from the source increases. Reddening is caused by a thin iron-oxide coating on individual sand grains and can be used, in some cases, to map relative-age zones. Photographs of the Western (Libyan) Desert of Egypt indicate three distinct and nearly parallel color zones that have been correlated in the field with: (1) arable soil composed of quartz, clay, and calcium carbonate particles; (2) relatively active sand with or without sparse vegetation; and (3) relatively inactive sand mixed with dark (desert-varnished) pebbles. The youngest sands are in the form of longitudinal dunes, which are migrating to the south-southeast along the prevailing wind direction. Some of the young dune fields are encroaching on the western boundary of the fertile Nile Valley.

El-Baz, F.↗
NASA NTRS1979

Measurements of upper atmosphere water vapor made in situ with a new moisture sensor

A new thin-film aluminum oxide sensor, Aquamax II, has been developed for the measurement of stratospheric and upper tropospheric water vapor levels. The sensor is briefly described with attention given to its calibration and performance. Data obtained from six balloon flights are presented; almost all the results show a constant water vapor mixing ratio, in agreement with other data from midlatitude regions.

Chleck, D.↗
NASA NTRS1984

Efficient AlGaAs shallow-homojunction solar cells

Shallow-homojunction n+/p/p+ solar cells with one-sun, AM1 conversion efficiencies as high as 12.9 percent have been fabricated in Al0.2Ga0.8As epitaxial layers grown by organometallic chemical vapor deposition on single-crystal GaAs substrates. For these cells, which have n+ layers thinned by anodic oxidation to about 500 A, the quantum efficiencies in the short-wavelength portion of the spectrum are as high as the best reported for AlGaAs cells with high band-gap window layers.

Gale, R. P.↗
NASA NTRS1984

Ceramic-coated metals can survive contact with hot working fluid

Thermal barrier coatings (TBCs) have been developed as a means of protecting turbine blades and other engine hot section components whose surfaces are exposed to the most extreme operating conditions. By adding a thin, insulating ceramic oxide layer to an air-cooled turbine blade, the difference between the gas temperature and the metal temperature is further increased as a function of ceramic coating thickness, heat flux, and oxide thermal conductivity. An 0.04-cm thick ceramic layer can typically yield a 100-300 C temperature drop. Of the various techniques available for the deposition of thermal barrier coatings, the most common is that of plasma spraying. Significant improvements have been made in TBC durability through the use of bond coat compositions with increased oxidation resistance.

Levine, S. R.↗
NASA NTRS1988

Improved Charge-Coupled Imager For X Rays

Device proposed to improve imaging of x rays. Features thin layer of oxide in virtual phase to increase quantum efficiency and depletion layer nearly as thick as epitaxial silicon layer to increase resolution. Applications include imaging spectrometers for x-ray astronomy, investigations of plasmas, and x-ray crystallography.

Wadsworth, Mark↗
NASA NTRS1990

Characterization of Iridium Coated Rhenium Used in High-Temperature, Radiation-Cooled Rocket Thrusters

Materials used for radiation-cooled rocket thrusters must be capable of surviving under extreme conditions of high-temperatures and oxidizing environments. While combustion efficiency is optimized at high temperatures, many refractory metals are unsuitable for thruster applications due to rapid material loss from the formation of volatile oxides. This process occurs during thruster operation by reaction of the combustion products with the material surface. Aerojet Technical Systems has developed a thruster cone chamber constructed of Re coated with Ir on the inside surface where exposure to the rocket exhaust occurs. Re maintains its structural integrity at high temperature and the Ir coating is applied as an oxidation barrier. Ir also forms volatile oxide species (IrO2 and IrO3) but at a considerably slower rate than Re. In order to understand the performance limits of Ir-coated Re thrusters, we are investigating the interdiffusion and oxidation kinetics of Ir/Re. The formation of iridium and rhenium oxides has been monitored in situ by Raman spectroscopy during high temperature exposure to oxygen. For pure Ir, the growth of oxide films as thin as approximately 200 A could be easily detected and the formation of IrO2 was observed at temperatures as low as 600 C. Ir/Re diffusion test specimens were prepared by magnetron sputtering of Ir on Re substrates. Concentration profiles were determined by sputter Auger depth profiles of the heat treated specimens. Significant interdiffusion was observed at temperatures as low as 1000 C. Measurements of the activation energy suggest that below 1350 C, the dominant diffusion path is along defects, most likely grain boundaries, rather than bulk diffusion through the grains. The phases that form during interdiffusion have been examined by x ray diffraction. Analysis of heated test specimens indicates that the Ir-Re reaction produces a solid solution phase of Ir dissolved in the HCP structure of Re.

Stulen, R. H.↗
NASA NTRS1993

Ellipsometric characterization of In(0.52)Al(0.48)As and of modulation doped field effect transistor structures on InP substrates

The dielectric function of a thick layer of In(0.52)Al(0.48)As lattice matched to InP was measured by variable angle spectroscopic ellipsometry in the range 1.9-4.1 eV. The In(0.52)Al(0.48)As was protected from oxidation using a thin In(0.53)Ga(0.47)As cap that was mathematically removed for the dielectric function estimate. The In(0.52)Al(0.48)As dielectric function was then verified by ellipsometric measurements of other In(0.53)Ga(0.47)As/In(0.52)Al(0.48)As structures, including (MODFET), and is shown to provide accurate structure layer thicknesses.

Alterovitz, S. A.↗
NASA NTRS1996

Polyimides That Contain Pendent Siloxane Groups

Polyimides containing pendent siloxane groups (PISOXs) synthesized from polyimides containing hydroxy groups (PIOHs) according to either of two alternative approaches. Addition of pendent siloxane groups to polyimide decreases dielectric constant, and decreases absorption of moisture: these changes in properties advantageous in some electronic applications. Also enhance resistance to atomic oxygen in that they undergo slight degradation to form thin protective silicon oxide coats when exposed to atomic oxygen.

Connell, John W.↗
NASA NTRS1999

A Precise Calibration Technique for Measuring High Gas Temperatures

A technique was developed for direct measurement of gas temperatures in the range of 2050 K - 2700 K with improved accuracy and reproducibility. The technique utilized the low-emittance of certain fibrous Materials, and the uncertainty of the technique was limited by the uncertainty in the melting points of the materials, i.e., +/- 15 K. The materials were pure, thin, metal-oxide fibers whose diameters varied from 60 mm to 400 mm in the experiments. The sharp increase in the emittance of the fibers upon melting was utilized as indication of reaching a known gas temperature. The accuracy of the technique was confirmed by both calculated low emittance values of transparent fibers, of order 0.01, up to a few degrees below their melting point and by the fiber-diameter independence of the results. This melting-point temperature was approached by increments not larger than 4 K, which was accomplished by controlled increases of reactant flow rates in hydrogen-air and/or hydrogen- oxygen flames. As examples of the applications of the technique, the gas-temperature measurements were used (a) for assessing the uncertainty in infering gas temperatures from thermocouple measurements, and (b) for calibrating an IR camera to measure gas temperatures. The technique offers an excellent calibration reference for other gas-temperature measurement methods to improve their accuracy and reliably extending their temperature range of applicability.

Gokoglu, Suleyman A.↗
NASA NTRS2000

A Precise Calibration Technique for Measuring High Gas Temperatures

A technique was developed for direct measurement of gas temperatures in the range of 2050 K 2700 K with improved accuracy and reproducibility. The technique utilized the low-emittance of certain fibrous materials, and the uncertainty of the technique was United by the uncertainty in the melting points of the materials, i.e., +/-15 K. The materials were pure, thin, metal-oxide fibers whose diameters varied from 60 microns to 400 microns in the experiments. The sharp increase in the emittance of the fibers upon melting was utilized as indication of reaching a known gas temperature. The accuracy of the technique was confirmed by both calculated low emittance values of transparent fibers, of order 0.01, up to a few degrees below their melting point and by the fiber-diameter independence of the results. This melting-point temperature was approached by increments not larger than 4 K, which was accomplished by controlled increases of reactant flow rates in hydrogen-air and/or hydrogen-oxygen flames. As examples of the applications of the technique, the gas-temperature measurements were used: (a) for assessing the uncertainty in inferring gas temperatures from thermocouple measurements, and (b) for calibrating an IR camera to measure gas temperatures. The technique offers an excellent calibration reference for other gas-temperature measurement methods to improve their accuracy and reliably extending their temperature range of applicability.

Gokoglu, Suleyman A.↗
NASA NTRS2002

Minimum Arc Threshold Voltage Experiments on Extravehicular Mobility Unit Samples

The International Space Station (ISS) is now under construction in Low Earth Orbit (LEO). The process of building the ISS requires that astronauts carry out many Extravehicular Activities. To protect the astronauts form the hazardous space environment, they are required to wear a suit known as the Extravehicular Mobility Unit (EMU). For most Extra-Vehicular Activities (EVAs) the EMU is tethered to ISS via a steel safety tether. During the course of an EVA it is common for the safety tether to contact exposed metal on both the ISS and the EMU. In this case, the single point ground of the EMU would be at the same potential as the ISS with respect to the LEO Plasma. In the event that the metal structure of the ISS begins to charge negative of the plasma potential as a result of electron collection by the ISS photovoltaic arrays, then the EMU would also be driven to a negative potential. Anodized aluminum components on the EMU would then begin to develop a charge across their amortization layer as ions from the plasma are collected. In the case where large negative potentials are applied to the EMU, dielectric breakdown may occur as a large voltage difference is developed across the thin amortization layer (oxide). The resulting arc plasma may in turn couple to the charge accumulated on the nearby ISS anodized debris shields and thereby generate a large current flow through the metal EMU structure. Current flow through the EMU could result in an electrocution hazard for the Crew Member inside the EMU - and therefore represents an important safety concern. To address this concern, a series of experiments have been undertaken. In each experiment specially prepared anodized aluminum samples were placed in a LEO representative plasma and charged until dielectric breakdown occurred in the form of an arc. This process was repeated a number of times for three sets of samples. During each test the arc voltage and current were monitored. A statistical treatment of the arc voltage threshold will be presented. In addition, safe operating voltages for the EMU are suggested.

Schneider, Todd↗
NASA NTRS1996

Protective, Abrasion-Resistant Coatings With Tailorable Properties

Because of their light weight and impact resistance, transparent plastic structures are becoming increasingly desirable for use not only on aircraft but also in terrestrial applications such as automotive windshields and ophthalmic lenses. However, plastics are typically soft and scratch readily, reducing their transparency with use. At the NASA Lewis Research Center, reactively deposited aluminum oxide coatings as thin as 12,000 angstroms have been demonstrated to provide improved resistance to most scratches encountered during normal use. The properties of the coating can be adjusted to tailor the surface to meet other needs, such as water shedding. These adjustments can be made during the deposition process so that multiple manufacturing steps are eliminated.

Source record↗
NASA NTRS2004

Finite Element Analysis of MEMS Devices

A side-slide actuator and a corrugated diaphragm actuator will be analyzed and optimized this summer. Coupled electrostatic and fluid analyses will also be initiated. Both the side-slide actuator and the corrugated diaphragm actuator will be used to regulate the flow of fuel in a jet engine. Many of the side-slide actuators will be placed on top of a fuel injector that is still in the developmental stage as well. The corrugated diaphragm actuator will also be used to regulate the flow of fuel in fuel injectors. A comparative analysis of the performance matrix of both actuators will be conducted. The side-slide actuator uses the concept of mechanical advantage to regulate the flow of fuel using electrostatic forces. It is made from Nickel, Silicon Carbide, and thin layers of Oxide. The slider will have a hole in the middle that will allow fuel to pass through the hole underneath it. The goal is to regulate the flow of fuel through the inlet. This means that the actuator needs to be designed so that when a voltage is applied to the push rod, the slider will deflect in the x-direction and be able to completely block the inlet and no fuel can pass through. Different voltage levels will be tested. The parameters that are being optimized are the thickness of the diaphragm, what kind of corrugation the diaphragm should have, the length, width, and thickness of the push rod, and what design should be used to return the slider. The current possibilities for a return rod are a built in spring on the slider, a return rod that acts like a spring, or a return rod that is identical to the push rod. The final actuator design should have a push rod that has rotational motion and no translation motion, a push rod thickness that prevents warping due to the slider, and a large ratio of the displacement on the bottom of the push rod to displacement on the top of the push rod. The corrugated diaphragm actuator was optimized last winter and this summer will be spent completing the optimization of the coupled electrostatic and fluid flow parameters. It was found that Nickel is the best material to use for the diaphragm because it has a higher yield strength and allows for a larger stress, deflection and applied pressure. The parameters that were optimized were the wavelength and thickness of the diaphragm.

Corrigan, Jennifer↗
NASA NTRS2009

NASA Tech Briefs, July 2009

Topics covered include: Dual Cryogenic Capacitive Density Sensor; Hail Monitor Sensor; Miniature Six-Axis Load Sensor for Robotic Fingertip; Improved Blackbody Temperature Sensors for a Vacuum Furnace; Wrap-Around Out-the-Window Sensor Fusion System; Wide-Range Temperature Sensors with High-Level Pulse Train Output; Terminal Descent Sensor Simulation; A Robust Mechanical Sensing System for Unmanned Sea Surface Vehicles; Additive for Low-Temperature Operation of Li-(CF)n Cells; Li/CFx Cells Optimized for Low-Temperature Operation; Number Codes Readable by Magnetic-Field-Response Recorders; Determining Locations by Use of Networks of Passive Beacons; Superconducting Hot-Electron Submillimeter-Wave Detector; Large-Aperture Membrane Active Phased-Array Antennas; Optical Injection Locking of a VCSEL in an OEO; Measuring Multiple Resistances Using Single-Point Excitation; Improved-Bandwidth Transimpedance Amplifier; Inter-Symbol Guard Time for Synchronizing Optical PPM; Novel Materials Containing Single-Wall Carbon Nanotubes Wrapped in Polymer Molecules; Light-Curing Adhesive Repair Tapes; Thin-Film Solid Oxide Fuel Cells; Zinc Alloys for the Fabrication of Semiconductor Devices; Small, Lightweight, Collapsible Glove Box; Radial Halbach Magnetic Bearings; Aerial Deployment and Inflation System for Mars Helium Balloons; Steel Primer Chamber Assemblies for Dual Initiated Pyrovalves; Voice Coil Percussive Mechanism Concept for Hammer Drill; Inherently Ducted Propfans and Bi-Props; Silicon Nanowire Growth at Chosen Positions and Orientations; Detecting Airborne Mercury by Use of Gold Nanowires; Detecting Airborne Mercury by Use of Palladium Chloride; Micro Electron MicroProbe and Sample Analyzer; Nanowire Electron Scattering Spectroscopy; Electron-Spin Filters Would Offer Spin Polarization Greater than 1; Subcritical-Water Extraction of Organics from Solid Matrices; A Model for Predicting Thermoelectric Properties of Bi2Te3; Integrated Miniature Arrays of Optical Biomolecule Detectors; A Software Rejuvenation Framework for Distributed Computing; Kurtosis Approach to Solution of a Nonlinear ICA Problem; Robust Software Architecture for Robots; R4SA for Controlling Robots; Bio-Inspired Neural Model for Learning Dynamic Models; Evolutionary Computing Methods for Spectral Retrieval; Monitoring Disasters by Use of Instrumented Robotic Aircraft; Complexity for Survival of Living Systems; Using Drained Spacecraft Propellant Tanks for Habitation; Connecting Node; and Electrolytes for Low-Temperature Operation of Li-CFx Cells.

Source record↗
NASA NTRS2001

Flow-Tagging Velocimetry for Hypersonic Flows Using Fluorescence of Nitric Oxide

We investigate a new type of flow-tagging velocimetry technique for hypersonic flows. The technique involves exciting a thin line of nitric oxide molecules with a laser beam and then, after some delay, acquiring an image of the displaced line. One component of velocity is determined from the time of flight. This method is applied to measure the velocity profile in a Mach 8.5 laminar, hypersonic boundary layer in the Australian National Universities T2 free-piston shock tunnel. The velocity is measured with an uncertainty of approximately 2%. Comparison with a CFD simulation of the flow shows reasonable agreement.

Danehy, P. M.↗