Search NASA⌕ Search

SEARCH · Search NASA

Results for “tiltrotor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

Application of Climate Impact Metrics to Civil Tiltrotor Design

Multiple metrics are applied to the design of a large civil tiltrotor, integrating minimum cost and minimum environmental impact. The design mission is passenger transport with similar range and capacity to a regional jet. Separate aircraft designs are generated for minimum empty weight, fuel burn, and environmental impact. A metric specifically developed for the design of aircraft is employed to evaluate emissions. The designs are generated using the NDARC rotorcraft sizing code, and rotor analysis is performed with the CAMRAD II aeromechanics code. Design and mission parameters such as wing loading, disk loading, and cruise altitude are varied to minimize both cost and environmental impact metrics. This paper presents the results of these parametric sweeps as well as the final aircraft designs.

Russell, Carl R.↗
NASA NTRS2013

Large Civil Tiltrotor (LCTR2) Interior Noise Predictions due to Turbulent Boundary Layer Excitation

The Large Civil Tiltrotor (LCTR2) is a conceptual vehicle that has a design goal to transport 90 passengers over a distance of 1800 km at a speed of 556 km/hr. In this study noise predictions were made in the notional LCTR2 cabin due to Cockburn/Robertson and Efimtsov turbulent boundary layer (TBL) excitation models. A narrowband hybrid Finite Element (FE) analysis was performed for the low frequencies (6-141 Hz) and a Statistical Energy Analysis (SEA) was conducted for the high frequency one-third octave bands (125- 8000 Hz). It is shown that the interior sound pressure level distribution in the low frequencies is governed by interactions between individual structural and acoustic modes. The spatially averaged predicted interior sound pressure levels for the low frequency hybrid FE and the high frequency SEA analyses, due to the Efimtsov turbulent boundary layer excitation, were within 1 dB in the common 125 Hz one-third octave band. The averaged interior noise levels for the LCTR2 cabin were predicted lower than the levels in a comparable Bombardier Q400 aircraft cabin during cruise flight due to the higher cruise altitude and lower Mach number of the LCTR2. LCTR2 cabin noise due to TBL excitation during cruise flight was found not unacceptable for crew or passengers when predictions were compared to an acoustic survey on a Q400 aircraft.

Grosveld, Ferdinand W.↗
NASA NTRS2013

Defining Gas Turbine Engine Performance Requirements for the Large Civil TiltRotor (LCTR2)

Defining specific engine requirements is a critical part of identifying technologies and operational models for potential future rotary wing vehicles. NASA's Fundamental Aeronautics Program, Subsonic Rotary Wing Project has identified the Large Civil TiltRotor (LCTR) as the configuration to best meet technology goals. This notional vehicle concept has evolved with more clearly defined mission and operational requirements to the LCTR-iteration 2 (LCTR2). This paper reports on efforts to further review and refine the LCTR2 analyses to ascertain specific engine requirements and propulsion sizing criteria. The baseline mission and other design or operational requirements are reviewed. Analysis tools are described to help understand their interactions and underlying assumptions. Various design and operational conditions are presented and explained for their contribution to defining operational and engine requirements. These identified engine requirements are discussed to suggest which are most critical to the engine sizing and operation. The most-critical engine requirements are compared to in-house NASA engine simulations to try to ascertain which operational requirements define engine requirements versus points within the available engine operational capability. Finally, results are summarized with suggestions for future efforts to improve analysis capabilities, and better define and refine mission and operational requirements.

Snyder, Christopher A.↗
NASA NTRS2016

Photogrammetric Deflection Measurements for the Tiltrotor Test Rig (TTR) Multi-Component Rotor Balance Calibration

Calibrating the internal, multi-component balance mounted in the Tiltrotor Test Rig (TTR) required photogrammetric measurements to determine the location and orientation of forces applied to the balance. The TTR, with the balance and calibration hardware attached, was mounted in a custom calibration stand. Calibration loads were applied using eleven hydraulic actuators, operating in tension only, that were attached to the forward frame of the calibration stand and the TTR calibration hardware via linkages with in-line load cells. Before the linkages were installed, photogrammetry was used to determine the location of the linkage attachment points on the forward frame and on the TTR calibration hardware. Photogrammetric measurements were used to determine the displacement of the linkage attachment points on the TTR due to deflection of the hardware under applied loads. These measurements represent the first photogrammetric deflection measurements to be made to support 6-component rotor balance calibration. This paper describes the design of the TTR and the calibration hardware, and presents the development, set-up and use of the photogrammetry system, along with some selected measurement results.

Calibration↗
NASA NTRS2016

Second-Generation Large Civil Tiltrotor 7- by 10-Foot Wind Tunnel Test Data Report

An approximately 6-percent scale model of the NASA Second-Generation Large Civil Tiltrotor (LCTR2) Aircraft was tested in the U.S. Army 7- by 10-Foot Wind Tunnel at NASA Ames Research Center January 4 to April 19, 2012, and September 18 to November 1, 2013. The full model was tested, along with modified versions in order to determine the effects of the wing tip extensions and nacelles; the wing was also tested separately in the various configurations. In both cases, the wing and nacelles used were adopted from the U.S. Army High Efficiency Tilt Rotor (HETR) aircraft, in order to limit the cost of the experiment. The full airframe was tested in high-speed cruise and low-speed hover flight conditions, while the wing was tested only in cruise conditions, with Reynolds numbers ranging from 0 to 1.4 million. In all cases, the external scale system of the wind tunnel was used to collect data. Both models were mounted to the scale using two support struts attached underneath the wing; the full airframe model also used a third strut attached at the tail. The collected data provides insight into the performance of the preliminary design of the LCTR2 and will be used for computational fluid dynamics (CFD) validation and the development of flight dynamics simulation models.

Theodore, Colin R.↗
NASA NTRS2019

Aeroelastic Stability Analysis of a Full-Scale Isolated Proprotor on the Tiltrotor Test Rig

A full-scale isolated proprotor test was recently conducted in the USAF National Full-Scale Aerodynamics Complex (NFAC) 40- by 80-Foot Wind Tunnel at NASA Ames. The test article was a 3-bladed research rotor derived from the right-hand rotor of the AW609. For this test, the NASA Tiltrotor Test Rig (TTR) and rotor were installed in the 40- by 80-Foot Wind Tunnel. This paper covers the analyses and testing done to prepare for a safe entry. Included are brief descriptions of the following: NASTRAN models of the TTR, ground vibration tests of the TTR (and resulting modal data), loads analyses, and stability predictions using the comprehensive analysis CAMRAD II. The evolution of these analyses from early in the TTR program until the initiation of actual testing is also discussed. The intent is to show how all of these efforts were integrated to ensure a successful test. This paper includes stability predictions based on NASTRAN modal data and worst-case damping test data. The stability predictions covered all test conditions: hover, cruise (airplane mode), conversion, and helicopter mode. The predictions showed that the TTR and rotor are stable within the test envelope.

Full-Scale Isolated Proprotor↗
NASA NTRS2019

Acoustic Testing of the Tiltrotor Test Rig in the National Full-Scale Aerodynamics Complex 40- by 80-Foot Wind Tunnel

The Tiltrotor Test Rig (TTR) was tested in the National Full-Scale Aerodynamics Complex (NFAC) 40- by 80-Foot Wind Tunnel from 2017 to 2018. The primary goal of the test was to understand the operational capabilities of the TTR, while also acquiring research data, including acoustic data. Four microphones were placed around the TTR: two on the wind tunnel floor and two on struts. Acoustic measurements of the TTR rotor were acquired to 1) understand the acoustic testing capabilities of the TTR in the NFAC 40- by 80-FootWind Tunnel, 2) compare to previous XV-15 rotor acoustic data acquired in the NFAC 80- by 120-Foot Wind Tunnel, and 3) provide data for future validation studies. A data quality study revealed that the NFAC 40- by 80-Foot Wind Tunnel is an adequate acoustic environment to test the TTR rotor. For a given thrust and advance ratio, a shaft angle sweep was performed and acoustic measurements were compared against 1996 and 1999 XV-15 data in the NFAC 80- by 120-Foot Wind Tunnel; differences between the three tests are discussed.

40- by 80-FootWind Tunnel↗
NASA NTRS2020

Vertical Climb Testing of a Full-Scale Proprotor on the Tiltrotor Test Rig

The Tiltrotor Test Rig (TTR) is a new NASA facility for testing full-scale proprotors. The first test campaign in the National Full-Scale Aerodynamics Facility (NFAC) concluded in November 2018. The wind-tunnel test included vertical climb conditions; that is, axial flow at low airspeeds (true hover is not possible in the NFAC). The rotor tested was the Bell Model 699, a 609 rotor modified specifically for wind-tunnel testing. The rotor was tested under a variety of NFAC configurations, some unprecedented and unique to vertical climb. Researchers must understand the differences in configuration if they are to make proper use of the data. This paper presents results for several different test configurations, including assessments of data quality. Comparisons with earlier tests of a similar rotor, the 0.656- scale Joint Vertical Experimental (JVX) rotor, are included to provide additional insights into rotor and wind tunnel behavior.

Acree, C. W.↗
NASA NTRS2020

Loads Correlation of a Full-Scale Proprotor on the Tiltrotor Test Rig

In 2018, a full-scale isolated proprotor test was conducted in the USAF National Full-Scale Aerodynamics Complex (NFAC) at NASA Ames. The test article was the 3-bladed Bell 699 research rotor derived from the AW609 rotor. For this test, the NASA Tiltrotor Test Rig (TTR) and rotor were installed in the 40- by 80-foot test section. Correlations between the 2018 test data and predictions from the comprehensive analysis CAMRAD II for blade and yoke (flexbeam) loads and rotor torque are presented. The full range of conversion to helicopter modes is covered: conversion 30-, 45-, and 60-deg TTR yaw, and helicopter 75- and 90-deg TTR yaw. The flap moment correlation is reasonable to good; the pitch link load and torsion moment are uniformly underpredicted. The measured 2P lag moment and 2P torque are not captured by the analysis. The inability to predict the 2P component is currently attributed to the analytical assumption of a perfect gimbal, whereas the actual test gimbal may be operating imperfectly and thus introducing the 2P harmonic. A new analytical model that accounts for non-ideal gimbal operation is needed.

Kottapalli, Sesi↗
NASA NTRS2020

Acoustic Testing of the Bell 699 Rotor on the Tiltrotor Test Rig (TTR) in the National Full-Scale Aerodynamics Complex 40- by 80- Foot Wind Tunnel in Conversion and Airplane Configuration

The Tiltrotor Test Rig (TTR) provides new proprotor testing capabilities to the National Aeronautics and Space Administration (NASA) and the Department of Defense (DoD). A checkout test for the TTR with the 699 proprotor was performed in the National Full-Scale Aerodynamics Complex (NFAC) 40- by 80 Foot Wind Tunnel from 2017 to 2018. Four microphones were placed around the rotor to capture acoustic data. Revolution based acoustic data processing techniques are evaluated for appropriateness in both helicopter and airplane configurations. This paper presents the acoustic data acquired for the rotor in conversion and airplane configuration.

Shelts, Kelly↗
NASA NTRS2019

Aeroacoustic Measurements of the Bell 699 Rotor on the Tiltrotor Test Rig in the National Full-Scale Aerodynamics Complex 40- by 80-Foot Wind Tunnel

The Tiltrotor Test Rig (TTR) with the Bell 699 Rotor was tested in the National Full-Scale Aerodynamics Complex (NFAC) 40- by 80-Foot Wind Tunnel from 2017 to 2018. The primary goal of the test was to understand the operational capabilities of the TTR while also acquiring research data, including acoustic data. A data quality study revealed that the NFAC 40- by 80-Foot Wind Tunnel is an adequate acoustic environment to test the Bell 699 Rotor for helicopter, conversion, and airplane configurations. Representative acoustic data are presented, and selected acoustic data and corresponding test conditions are included.

Schatzman, N. L.↗
NASA NTRS1987

External noise evaluation of the XV-15 TiltRotor aircraft

The noise emission of the XV-15 in both helicopter and airplane operation and in level and constant-slope descending flight is measured (as sound exposure levels) in a series of test flights over a ground microphone array. The aircraft characteristics, test facility, and procedures are described, and the results are presented in extensive graphs and characterized in detail. Consideration is given to engine-rpm and nacelle-tilt effects, noise duration, sideline radiation, altitude effects, acoustic waveforms, and variations with glideslope. The XV-15 is found to produce less noise in its airplane mode than in the helicopter mode, where the noise levels are similar to those of other helicopters.

Brieger, John T.↗
NASA NTRS1989

Noise considerations for tiltrotor

A projection is made of the technology-development requirements faced by aircraft designers contemplating the evolution of V-22-type tilt-rotor aircraft technology into a civilian tilt-rotor commuter aircraft of the requisite scale and payload. These research challenges are noted to often involve the reduction of noise level to values tolerated by passengers within the cabin and communities in the vicinity of airports, especially during hover and in the course of transition from vertical to horizontal flight (and vice-versa). Noise-generation and noise-radiation characteristics research has been undertaken using the XV-15 tilt-rotor proof-of-concept aircraft.

Huston, Robert J.↗
NASA NTRS1988

A look at tomorrow's civil tiltrotor

The present evaluation of the development status of the tilt-rotor VTOL aircraft concept proceeds to identify a large civilian market potential for vehicles of this type, especially along high commuter traffic density urban corridors. A variant of the V-22 tilt-rotor is judged to be of sufficient size for this high-density passenger market in the near term, provided that the rotor-drive system undergoes suitable modifications for more reliable one-engine-inoperative emergency operation. New, larger-than-V-22 and least-cost-optimized civil tilt-rotors carrying as many as 75 passengers are under study, but will require the construction of 'vertiports' at strategically advantageous urban locations.

Wilkerson, Joseph B.↗
NASA NTRS1991

A comparative analysis of XV-15 tiltrotor hover test data and WOPWOP predictions incorporating the fountain effect

Acoustic measurements from a hovering full scale XV-15 tilt rotor with the advanced technology blades are presented which show the directionality of fountain effect noise. Predicted acoustic directivity results are also presented which show agreement with the measured data. The aeroacoustic code, WOPWOP, was used in conjunction with a mathematical model which simulated the fountain recirculation aerodynamic effect on the rotor blade surface pressures. The predictions were used to identify the spike character in the measured data as fountain effect associated noise. The directivity of the fountain effect noise was observed to be dominant at the rear of the aircraft with increased intensities 45 degrees below the rotor disk planes.

Rutledge, Charles K.↗
NASA NTRS1993

Design of an air traffic computer simulation system to support investigation of civil tiltrotor aircraft operations

The TATSS Project's goal was to develop a design for computer software that would support the attainment of the following objectives for the air traffic simulation model: (1) Full freedom of movement for each aircraft object in the simulation model. Each aircraft object may follow any designated flight plan or flight path necessary as required by the experiment under consideration. (2) Object position precision up to +/- 3 meters vertically and +/- 15 meters horizontally. (3) Aircraft maneuvering in three space with the object position precision identified above. (4) Air traffic control operations and procedures. (5) Radar, communication, navaid, and landing aid performance. (6) Weather. (7) Ground obstructions and terrain. (8) Detection and recording of separation violations. (9) Measures of performance including deviations from flight plans, air space violations, air traffic control messages per aircraft, and traditional temporal based measures.

Rogers, Ralph V.↗
NASA NTRS1992

Acoustic flight test experience with the XV-15 Tiltrotor aircraft with the Advanced Technology Blade (ATB)

An acoustic model that predicts the discrete frequency noise characteristics of helicopter rotors has been utilized in an analysis to help identify source characteristics. This technique incorporated a NASA Langley developed acoustic prediction technique, and a simplified flow field model to account for rotor wake reingestion in hover. The vehicle rotor system was modified to include the ATBs that were designed to provide for higher operating weights and improved maneuver load factor in helicopter and transition modes of operation.

Hoad, Danny R.↗