Search NASA⌕ Search

SEARCH · Search NASA

Results for “toroidal magnetic confinement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Multimachine analysis of intermittent fluctuations in the scrape-off layer of magnetically confined fusion plasmas

Far scrape-off layer fluctuations, also known as blobs/filaments, are compared for the first time across six tokamaks: Alcator C-Mod, DIII-D, TCV, KSTAR, MAST, and MAST-U, under the context of stochastic modeling in Ohmic and low confinement mode scenarios. In this model, which well describes these fluctuations, measurements from Langmuir probes are modeled as a superposition of uncorrelated, two-sided exponential temporal pulses. The key parameters of this model are the mean waiting times between consecutive pulses, the pulse duration times and the mean of the pulse amplitudes. The study examines the influence of line-averaged density, plasma current, magnetic field and aspect ratio. The mean amplitudes and pulse waiting times increase with the line-averaged density across devices, while the pulse duration times remain constant. Whereas the variation in waiting times is gradual across the density scan, the mean amplitudes increase abruptly as the density profile broadens and flattens for Alcator C-Mod. The blob waiting times decrease with increasing plasma current and the toroidal magnetic field, while they increase with aspect ratio for conventional tokamaks. The duration times follow the same trends as the waiting times in these parameters but vary more slowly, resulting in the trends in the waiting times dominating the intermittency level of the fluctuations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Efficient electron cyclotron current drive regime for plasma current start-up in fusion reactors

We report an accessibility enhanced efficient fundamental X-mode electron cyclotron heating (ECH) current start-up regime was identified for a reactorlike toroidal magnetic field range which has more than 100 times higher current drive efficiency compared to more conventional ECH methods for the relevant start-up temperature range. Very high current drive efficiency is possible due to the strong cyclotron interaction only with unidirectional passing electrons constrained by the wave accessibility conditions. This efficient electron cyclotron current drive regime may help facilitate the design of innovative economical solenoid-free tokamak fusion reactor systems.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Observations of a plectonemic configuration in a stable magnetized plasma jet

Astrophysical jets are collimated high-speed outflows emerging from spinning and accreting matter around celestial objects and may spontaneously result from self-organized processes. Magnetic self-organization is commonly observed in laboratory plasma physics experiments; however, they require close-fitting flux conservers to constrain and stabilize the toroidal or cylindrical structures. Here we report the first observations of a long, stable, free-boundary plasma jet far from chamber walls, embedding a double-helix magnetic structure resembling a force-free plectonemic Taylor state. The jets arise from an experimental setup that mimics an accretion disk and has no close-fitting solid flux conserver. The results support the hypothesis that self-organization could be a universal, intrinsic explanation for jet formation, collimation, and stability and may help explain double-helix features in celestial observations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Creation and sustainment of wide pedestal quiescent H-mode with zero net neutral beam torque

Recent experiments on DIII-D have shown it is possible to create and sustain wide pedestal quiescent H-mode (QH-mode) plasmas with zero net torque from neutral beam injection (NBI) for the full discharge duration. Wide pedestal QH-mode has many of the features of the previously investigated QH-mode while having the advantage of increased edge pedestal pressure and excellent energy confinement time. Both QH-mode variants operate without edge localized modes. Accordingly, these discharges demonstrate that significant input torque is not essential to the exploitation of wide pedestal QH-mode in future devices that are expected to have small or nonexistent NBI torque. In conclusion, developing operating conditions that allowed net zero torque access to wide pedestal QH-mode required implementing several techniques to avoid locked modes including minimizing intrinsic error fields, avoiding large sawteeth, and driving toroidal rotation via neoclassical toroidal viscosity.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Simulations of vertical displacement oscillatory modes and global Alfvén Eigenmodes in JET geometry

Vertical Displacement Oscillatory Modes (VDOM), with frequency in the Alfvén range, are natural modes of oscillation of magnetically confined laboratory plasmas with elongated cross-section. These axisymmetric modes arise from the interaction between the plasma current, which is in equilibrium with currents flowing in external coils, and perturbed currents induced on a nearby conducting wall. The restoring force exerted by these perturbed currents on the vertical motion of the plasma column leads to its oscillatory behavior. An analytic model for VDOM was proposed based on an idealized 'straight tokamak' equilibrium with uniform equilibrium current density. This article introduces the first numerical simulations of VDOM in a realistic JET tokamak configuration, using the extended-MHD code NIMROD and drawing comparisons with Global Alfvén Eigenmodes (GAE). The results show qualitative agreement with analytic predictions regarding mode frequency and radial structure, supporting the identification of VDOM as a fundamental oscillation mode in tokamak plasmas. VDOM and GAE are modeled in a representative JET discharge, where axisymmetric perturbations with toroidal mode number n = 0 driven unstable by fast ions were observed. The two modes are examined separately using a forced oscillator within the NIMROD code, which enables a comparison of their characteristics and helps identify the experimentally observed mode possibly as a GAE.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

First simultaneous observation of co- and counter-current fast-ion losses in the ASDEX Upgrade tokamak

In ITER and future fusion power plants, the source of the fusion born alpha particles is almost isotropic in pitch angle, thus having co- and counter-current populations. For trapped ions, the co-current side of the orbit corresponds to its outer leg, while the counter-current side corresponds to the inner leg. Understanding the mechanisms responsible for the fast-ion losses (FILs) is critical for future magnetically confined fusion power plants. To further study the interplay of fast ions with plasma instabilities, a double pinhole collimator has been developed for a Fast-Ion Loss Detector (FILD) in the ASDEX Upgrade tokamak (AUG). This new FILD opens the operational window to simultaneous measurements of the co- and counter-current ion velocity-space. In this paper, the first results for the AUG double collimator FILD detector are shown. The commissioning of this new probe is carried out in H-mode plasmas with an on-axis magnetic field $B_0 = -2.5$ T, and a plasma current $I_{\textrm{p}} = 0.7$ MA. Simultaneous co- and counter-current FILs have been measured. Both have shown a similar dependence on Ion Cyclotron Resonance Heating (ICRH) power, where the main difference is the intensity of the losses, with the co-losses being an order of magnitude larger. Toroidal Alfvén eigenmode-coherent ICRH-only losses have been identified for the co-current ions. Additionally, the presence of Edge Localized Modes during the discharge were shown to increment Neutral Beam Injection prompt losses, while partially mitigating ICRH-driven losses on both co- and counter- sides of the velocity-space. Finally, a very trapped and high gyroradius losses, with an unclear origin, have been measured in the co- and counter-current velocity-space. The computed ion trajectories show that these ions remain permanently near the vessel wall, suggesting that they are accelerated within the scrape-off layer.

ELM↗
DOE OSTI2019

Measurement of accreted helium ion velocity using Doppler spectroscopy in the CTIX compact-toroid plasma accelerator

A compact-toroid (CT) accelerator is a device for the production of plasma bodies which contain a relatively strong internal magnetic field, which permits the plasma body to withstand large forces of acceleration while retaining its magnetic field structure. Typically, the CT occupies an annular region between inner and outer radii, defined by coaxial inner and outer electrodes, across which a large electric potential is applied. The internal magnetic fields of the CT contain both a toroidal and poloidal component, as shown in Fig. 1(a). These fields are typically of comparable magnitude. Because of the effective rigidity provided by internal magnetic fields, the CT can be accelerated to high velocities in short distances. Since internal fields increase in proportion to accelerating magnetic field, there is no strength at which the accelerating magnetic fields overcome the internal field (blow-by). Because of this, the kinetic energy density of CTs can be made to exceed the energy density of magnetic fields typical of plasma containment devices such as tokamaks. CTs have the potential to be launched into the interior of such devices for either delivering fuel (typically deuterium or hydrogen), or to deliver particles of high atomic number (high-Z). An important application of high-Z CT injection into tokamaks is to aid in plasma quenching by radiation, to mitigate the effects of plasma disruptions and prevent damage to the plasma confinement device. In addition, high-Z CTs may be used as sources of kinetic energy density for plasma-compression experiments. In this case, the use of plasma species of high atomic number is also desirable, since kinetic energy density is proportional to atomic number for given CT velocity and electron density gas puffing.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Curvature of Radial Electric Field Aggravates Edge Magnetohydrodynamics Mode in Toroidally Confined Plasmas

We show that the radial electric field (E r ) plays a dual role in edge magnetohydrodynamics (MHD) activity. While E r shear (first spatial derivative of E r ) dephases radial velocity and displacement, and so is stabilizing, a new finding here is that E r curvature (second spatial derivative of E r ) tends to synchronize the radial velocity and displacement, and so destabilizes MHD. As a highlighted result, we analytically demonstrate that E r curvature can destabilize an otherwise stable kink mode, and so form a joint vortexkink mode. The synergetic effects of E r shear and E r curvature in edge MHD extend the familiar E × B shearing paradigm. This theory thus explains the experimental findings that a deeper E × B well may aggravate edge MHD, and so trigger the formation of the edge harmonic oscillation. Here, a simple criterion linking E r structure and the edge MHD activity is derived.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

DESC: A stellarator equilibrium solver

In this paper, the new code DESC is presented to solve for fixed-boundary ideal magnetohydrodynamic equilibria in stellarators. The approach directly solves the equilibrium force balance as a system of nonlinear equations in the form f(x) = 0. The independent variables x represent nested magnetic flux surfaces expressed in the inverse representation with toroidal flux coordinates, and the equations f(x) quantify equilibrium force balance errors at discrete points in real space. Discretizing with global Fourier–Zernike basis functions properly treats the magnetic axis and minimizes the number of coefficients needed to describe the flux surfaces. The pseudospectral method provides great flexibility in where the errors are evaluated, and the system of equations is efficiently solved with a Newton–Raphson iteration. Equilibria are computed and compared against VMEC for both axisymmetric and non-axisymmetric examples. The results show fast convergence rates and solutions with low errors throughout the plasma volume.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

First fluctuation measurements using an Imaging Neutral Particle Analyzer on DIII-D

A recent upgrade to the Imaging Neutral Particle Analyzer (INPA) on DIII-D has allowed for the first fluctuation measurements using an INPA to be taken during a neoclassical tearing mode (NTM). The INPA signal tracked the mode over 150 ms as the mode frequency dropped to zero, capturing both the NTM with poloidal and toroidal mode numbers $m/n=2/1$ and a $3/2$ mode at double the frequency. Analysis shows that the signals originate from charge exchange events near the edge of the plasma, and relative fluctuation amplitudes are greater than 25% for the duration of the NTM. Filtered signals show frequency beating patterns that are phase-space dependent. Simulated signal is dominated by prompt transport from the neutral beams to the INPA sightline, while the contribution from the slowing down distribution is significantly lower. Simulated measurements in the range of pitches that the diagnostic is sensitive to (0.5≤|v∥/v|≤ 0.75) show the signal is dominated by trapped orbits that pass through magnetic islands near the edge of the plasma. Calculations of expected fluctuation levels show that only direct interaction with the NTM can provide the strong relative fluctuation levels seen experimentally. The prompt nature of the orbits and thin radial layer found to contribute to synthetic signals suggest INPA passive data may be used to measure the perturbations of confined orbits on a single pass through a plasma instability.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Scattering of lower hybrid radio frequency waves by cylindrical turbulent structures in the plasma edge in tokamaks

Lower hybrid (LH) radio frequency (RF) waves are used in fusion tokamak devices to generate non-inductively toroidal currents. LH waves are effective in imparting toroidal momentum to electrons in the core of the confined plasma. Since the LH waves are generated by wave guide structures near the wall of a tokamak, the waves have to propagate through a turbulent plasma in the edge region before coupling to the core. It is especially important to quantify the effect of this plasma region on the propagation characteristics of the LH waves, since fusion reactors like ITER will have an extended edge region. Structures in the plasma edge like filaments and blobs which have highly varying density fluctuations compared to the background density, span radial spatial scales that are comparable to the LH wavelength. We study the scattering of the LH waves by the filamentary structures using Maxwell's equations, in which the plasma permittivity is given by the cold plasma dispersion tensor. The collisional absorption of LH waves in the edge region is included by a modification to the elements of the dispersion tensor. The filaments are assumed to be cylindrical with the axis predominantly aligned along the direction of the toroidal magnetic field. Our studies are both analytical and numerical [1,2] and show that these structures can lead to reflection, refraction, diffraction, and side-scattering of both an incident LH plane wave and a Gaussian beam. We will present a variety of different density variations and collisional absorption rates in plasmas with filamentary structures of varying sizes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

ELM control optimization for various ITER scenarios based on linear and quasi-linear figures of merit

For the purpose of better understanding type-I edge localized mode (ELM) control in ITER with resonant magnetic perturbation (RMP) fields, the plasma response to RMP is computed by a resistive full magneto-hydrodynamic model in toroidal geometry. Five scenarios designed for ITER are considered, ranging from the pre-nuclear to nuclear phases. The plasma response to RMP is quantified by the plasma surface displacement near the X-point of the divertor plasma and at the outboard mid-plane. The optimal coil configurations between two high- Q deuterium-tritium (DT) scenarios (at the same plasma current of 15 MA and the same magnetic field of 5.3 T but different fusion gains, Q = 5 and 10) are predicted to be similar. For the other ITER scenarios with similar edge safety factor q 95 ~ 3 to that of the baseline scenario, the optimal coil phasing is also similar. The optimization results are different for a half-current full-field (7.5 MA/5.3 T) scenario, largely due to the difference in q 95 . The RMP coil currents are also optimized to tailor the core vs edge toroidal torques exerted by the 3D RMP fields on the plasma column. Torque optimization, with various objective functions proposed in the study, is useful for minimizing the side effects of RMP on the plasma core flow in ITER, while still maintaining the ELM control capability. Full utilization of three rows of ELM control coils in ITER is found to be essential to ensure both flexibility and robustness of ELM control, in terms of both linear and quasilinear plasma responses.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Direct, simple and efficient computation of all components of the virtual-casing magnetic field in axisymmetric geometries with Kapur–Rokhlin quadrature

In a recent publication (Toler et al., J. Plasma Phys., vol. 89, issue 2, 2023, p. 905890210), we demonstrated that for axisymmetric geometries, the Kapur–Rokhlin quadrature rule provided an efficient and high-order accurate method for computing the normal component, on the plasma surface, of the magnetic field due to the toroidal current flowing in the plasma, via the virtual-casing principle. The calculation was indirect, as it required the prior computation of the magnetic vector potential from the virtual-casing principle, followed by the computation of its tangential derivative by Fourier differentiation, to obtain the normal component of the magnetic field. Our approach did not provide the other components of the virtual-casing magnetic field. In this letter, we show that a more direct and more general approach is available for the computation of the virtual-casing magnetic field. The Kapur–Rokhlin quadrature rule accurately calculates the principal value integrals in the expression for all the components of the magnetic field on the plasma boundary, and the numerical error converges at a rate nearly as high as the indirect method we presented previously.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Observations of heteroclinic bifurcations in resistive magnetohydrodynamic simulations of the plasma response to resonant magnetic perturbations

A class of topological magnetic island bifurcations that has not previously been observed in toroidal plasmas is described. Increasing an externally applied three-dimensional magnetic field in resistive magnetohydrodynamic simulations results in the asymmetric elongation of resonant island flux surfaces followed by a sequence of heteroclinic bifurcations. Here, these bifurcations produce new sets of hyperbolic-elliptic fixed points as predicted by the Poincaré-Birkoff fixed point theorem. Field line calculations verify that the new fixed points do not connect to those of the prebifurcated islands as required for heteroclinic bifurcations on a torus with winding numbers composed of common integer factors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Perturbed Ion Temperature and Toroidal Flow Profile Measurements in Rotating Neoclassical Tearing Mode Magnetic Islands

The perturbed ion temperature and toroidal flow were measured in rotating Neoclassical Tearing Modes (NTM) in a tokamak for the first time. These toroidally and radially resolved profiles were obtained by impurity ion spectroscopy in a 2,1 NTM in DIII-D. In agreement with drift-kinetic simulations, the electron temperature profile is flat, while the ion temperature gradient is restored across the magnetic island O-point in the presence of fast ions; the perturbed flow has minima in the O-points and maxima at the X-points. Furthermore, these measurements provide the first confirmation of the theoretically expected ion temperature and flow response to a magnetic island needed to predict the NTM on set threshold scaling for ITER and other future tokamaks.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Enhanced particle flux due to localized divertor MHD instability in DIII-D tokamak

An MHD mode with a frequency of <10 kHz has been identified near the inner strike point from various diagnostics, i.e., divertor Langmuir probes, magnetics sensors, and interferometers, but does not appear in the upstream and core diagnostics. This MHD mode is associated with magnetic oscillations of ≳5 G, has a long wavelength in the toroidal direction with toroidal mode number n=1, but is localized in a narrow radial region of a few cm. The mode appears when the outer strike point remains attached and the inner strike point nearly detaches, grows with increasing density, and eventually weakens and vanishes as the outer strike point detaches. This mode results in particle flux with an order of magnitude higher than the background plasmas near the inner strike point. The mode characteristics are consistent with the Current-Convective-Instability theory prediction. Initial simulations based on experimental input have found oscillations with similar frequencies but weaker amplitude.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Linear simulation of kinetic electromagnetic instabilities in a tokamak plasma with weak magnetic shear

Gyrokinetic simulation and eigenvalue calculation of electromagnetic instabilities are carried out for an experimentally observed low-n mode in weak magnetic shear discharge. With different magnetic shear values, the Gyrokinetic Toroidal Code simulation of the ion temperature gradient mode is consistent with the eigenvalue code (HD7) calculation. Due to the sensitivity of the kinetic ballooning mode (KBM) to global equilibrium, the simulation of the KBM deviates from the eigenvalue results, for the ballooning representation used in HD7 satisfies its spatial scale separations. Under a flat safety factor profile, the KBM is more unstable and its mode structure tends to move with the peak of the ion temperature drive. Further simulation of the KBM in an HL-2A-like equilibrium shows that the β excitation threshold of the mode is lower than 0.2% and the dominant toroidal mode number is n = 4, which is consistent with the measured experimental spectrum.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Nonlinear coupling of tearing modes in reversed field pinch plasmas with stepped pressure profiles

A theory of the three-wave coupling of triplets of tearing modes in toroidal pinches [i.e., either reversed field pinches (RFPs) or tokamaks] was proposed by R. Fitzpatrick [Phys. Plasmas 6, 1168 (1999)]. However, this theory only applies to toroidal pinches with negligible equilibrium plasma pressure gradients. Such a limitation is particularly inappropriate to RFPs. This paper generalizes the analysis of R. Fitzpatrick [Phys. Plasmas 6, 1168 (1999)] in order to take the equilibrium pressure gradient into account. However, for the sake of simplicity, a stepped pressure profile, rather than a continuous profile, is employed. In the limit in which the number of steps becomes very large, the results obtained from the generalized theory are presumably equivalent to those that would have been achieved using a continuous pressure profile. The generalized theory is used to investigate the formation of the characteristic toroidally localized pattern of phase-locked m = 1 and m = 0 tearing modes in RFP plasmas that is known as the “slinky” pattern. The incorporation of the equilibrium plasma pressure into the analysis is found to be of crucial importance when determining the properties of the pattern. This is the case because the plasma pressure controls the number of unstable m = 1 and m = 0 tearing modes, and also significantly affects the strength of three-wave coupling, as well as the phase relation between the phase-locked m = 1 and m = 0 modes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗