Search NASA⌕ Search

SEARCH · Search NASA

Results for “value factor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Heat transfer and fluid mechanics measurements in transitional boundary layer flows

Experimental results are presented to document hydrodynamic and thermal development of flat-plate boundary layers undergoing natural transition. Local heat transfer coefficients, skin friction coefficients and profiles of velocity, temperature and Reynolds normal and shear stresses are presented. A case with no transition and transitional cases with 0.68 percent and 2.0 percent free-stream disturbance intensities were investigated. The locations of transition are consistent with earlier data. A late-laminar state with significant levels of turbulence is documented. In late-transitional and early-turbulent flows, turbulent Prandtl number and conduction layer thickness values exceed, and the Reynolds analogy factor is less than, values previously measured in fully turbulent flows.

Wang, T.↗
NASA NTRS1987

Frequency functions of Venus nightside ion densities

The variability of the total and major ion densities in the nightside Venus ionosphere are studied by deriving an experimental frequency function for these quantities. The frequency function N(i) derived for the total ion density is found to be insensitive to division of the parent set into two approximately equal subsets representing dawn and dusk hemispheres, an upper and lower altitude interval, or two solar zenith angle intervals. The N(i) function is reasonably well peaked near the median value, and 78 percent of the normalized values fall within a factor of 2.8 of the median value. The frequency of occurrence decreases more rapidly on the high side of the median than on the low side. The frequency functions for the constituent ions are similar to that for N(i).

Knudsen, William C.↗
NASA NTRS2007

Development of a Linear Stirling Model with Varying Heat Inputs

The linear model of the Stirling system developed by NASA Glenn Research Center (GRC) has been extended to include a user-specified heat input. Previously developed linear models were limited to the Stirling convertor and electrical load. They represented the thermodynamic cycle with pressure factors that remained constant. The numerical values of the pressure factors were generated by linearizing GRC s non-linear System Dynamic Model (SDM) of the convertor at a chosen operating point. The pressure factors were fixed for that operating point, thus, the model lost accuracy if a transition to a different operating point were simulated. Although the previous linear model was used in developing controllers that manipulated current, voltage, and piston position, it could not be used in the development of control algorithms that regulated hot-end temperature. This basic model was extended to include the thermal dynamics associated with a hot-end temperature that varies over time in response to external changes as well as to changes in the Stirling cycle. The linear model described herein includes not only dynamics of the piston, displacer, gas, and electrical circuit, but also the transient effects of the heater head thermal inertia. The linear version algebraically couples two separate linear dynamic models, one model of the Stirling convertor and one model of the thermal system, through the pressure factors. The thermal system model includes heat flow of heat transfer fluid, insulation loss, and temperature drops from the heat source to the Stirling convertor expansion space. The linear model was compared to a nonlinear model, and performance was very similar. The resulting linear model can be implemented in a variety of computing environments, and is suitable for analysis with classical and state space controls analysis techniques.

Regan, Timothy F.↗
NASA NTRS2007

Development of a Linear Stirling System Model with Varying Heat Inputs

The linear model of the Stirling system developed by NASA Glenn Research Center (GRC) has been extended to include a user-specified heat input. Previously developed linear models were limited to the Stirling convertor and electrical load. They represented the thermodynamic cycle with pressure factors that remained constant. The numerical values of the pressure factors were generated by linearizing GRC's nonlinear System Dynamic Model (SDM) of the convertor at a chosen operating point. The pressure factors were fixed for that operating point, thus, the model lost accuracy if a transition to a different operating point were simulated. Although the previous linear model was used in developing controllers that manipulated current, voltage, and piston position, it could not be used in the development of control algorithms that regulated hot-end temperature. This basic model was extended to include the thermal dynamics associated with a hot-end temperature that varies over time in response to external changes as well as to changes in the Stirling cycle. The linear model described herein includes not only dynamics of the piston, displacer, gas, and electrical circuit, but also the transient effects of the heater head thermal inertia. The linear version algebraically couples two separate linear dynamic models, one model of the Stirling convertor and one model of the thermal system, through the pressure factors. The thermal system model includes heat flow of heat transfer fluid, insulation loss, and temperature drops from the heat source to the Stirling convertor expansion space. The linear model was compared to a nonlinear model, and performance was very similar. The resulting linear model can be implemented in a variety of computing environments, and is suitable for analysis with classical and state space controls analysis techniques.

Regan, Timothy F.↗
NASA NTRS1993

Depth-dose equivalent relationship for cosmic rays at various solar minima

Galactic cosmic rays (GCR) pose a serious radiation hazard for long-duration missions. In designing a lunar habitat or a Mars transfer vehicle, the radiation exposure determines the GCR shielding thickness, and hence the weight of spacecraft. Using the spherically symmetric diffusion theory of the solar modulation of GCR, and data on the differential energy spectra of H, He, O, and Fe, from 1965 to 1989, it has been shown that (1) the flux is determined by the diffusion parameter which is a function of the time in the solar cycle, and (2) the fluxes in the 1954 and 1976-1977 solar minima were similar and higher than those in 1965. In this paper, we have extended the spherical solar modulation theory back to 1954. The 1954-1955 GCR flux was nearly the same as that from 1976 to 1977; the 1965 flux values were nearly the same as those in 1986. Using this theory we have obtained the GCR spectra for all the nuclei, and calculated the depth dose as a function of Al thickness. It is shown that the shielding required to stay below 0.5 Sv is 17.5 -3/+8 g/sq cm of Al, and 9 -1.5/+5 g/sq cm to stay below 0.6 Sv. The calculated dose equivalent using the ICRP 60 values for quality factors is about 15 percent higher than that calculated using the ICRP 26 value.

Badhwar, G. D.↗
NASA NTRS2017

Cause and Cure - Deterioration in Accuracy of CFD Simulations With Use of High-Aspect-Ratio Triangular Tetrahedral Grids

Traditionally high-aspect ratio triangular/tetrahedral meshes are avoided by CFD re-searchers in the vicinity of a solid wall, as it is known to reduce the accuracy of gradient computations in those regions and also cause numerical instability. Although for certain complex geometries, the use of high-aspect ratio triangular/tetrahedral elements in the vicinity of a solid wall can be replaced by quadrilateral/prismatic elements, ability to use triangular/tetrahedral elements in such regions without any degradation in accuracy can be beneficial from a mesh generation point of view. The benefits also carry over to numerical frameworks such as the space-time conservation element and solution element (CESE), where triangular/tetrahedral elements are the mandatory building blocks. With the requirement of the CESE method in mind, a rigorous mathematical framework that clearly identities the reason behind the difficulties in use of such high-aspect ratio triangular/tetrahedral elements is presented here. As will be shown, it turns out that the degree of accuracy deterioration of gradient computation involving a triangular element is hinged on the value of its shape factor Gamma def = sq sin Alpha1 + sq sin Alpha2 + sq sin Alpha3, where Alpha1; Alpha2 and Alpha3 are the internal angles of the element. In fact, it is shown that the degree of accuracy deterioration increases monotonically as the value of Gamma decreases monotonically from its maximal value 9/4 (attained by an equilateral triangle only) to a value much less than 1 (associated with a highly obtuse triangle). By taking advantage of the fact that a high-aspect ratio triangle is not necessarily highly obtuse, and in fact it can have a shape factor whose value is close to the maximal value 9/4, a potential solution to avoid accuracy deterioration of gradient computation associated with a high-aspect ratio triangular grid is given. Also a brief discussion on the extension of the current mathematical framework to the tetrahedral-grid case along with some of the practical results of this extension is also provided. Furthermore, through the use of numerical simulations of practical viscous problems involving high-Reynolds number flows, the effectiveness of the gradient evaluation procedures within the CESE framework (that have their basis on the analysis presented here) to produce accurate and stable results on such high-aspect ratio meshes is also showcased.

CESE Method↗
NASA NTRS1986

Technique for Measuring Gas Conversion Factors

Technique for measuring calibration conversion factors for hydrocarbon mass flowmeters applied to widely used type of commercial thermal mass flowmeter for hydrocarbon gases. Values of conversion factors for two common hydrocarbons measured using this technique in good agreement with empirical values cited by manufacturer. Similar agreement expected for all other hydrocarbons. Technique based on Nernst theorem for matching partial pressure of oxygen in combustion product gases with that in normal air. Simple, quick, and relatively safe, particularly for toxic/poisonous hydrocarbons.

Singh, J. J.↗
NASA NTRS1973

A study to explore the use of orbital remote sensing to determine native arid plant distribution

The author has identified the following significant results. A theory has been developed of a method for determining the reflectivities of natural areas from ERTS-1 data. This method requires the following measurements: (1) ground truth reflectivity data from two different calibration areas; (2) radiance data from ERTS-1 MSS imagery for the same two calibration areas; and (3) radiance data from ERTS-1 MSS imagery for the area(s) in which reflectivity is to be determined. The method takes into account sun angle effects and atmospheric effects on the radiance seen by the space sensor. If certain assumptions are made, the ground truth data collection need not be simultaneous with the ERTS-1 overflight. The method allows the calculation of a conversion factor for converting ERTS-1 MSS radiance measurements of a given overflight to reflectivity values. This conversion factor can be used to determine the reflectivity of any area in the general vicinity of the calibration areas which has a relatively similar overlying atmosphere. This method, or some modification of it, may be useful in ERTS investigations which require the determination of spectral signatures of areas from spacecraft data.

Mcginnies, W. G.↗
NASA NTRS1988

Internal temperature gradient of alloy semiconductor melts from interrupted growth experiments

Interrupted growth experiments on Hg(0.8)Cd(0.2)Se alloys were performed in an attempt to estimate the actual internal temperature gradient in the melt during directional solidification. The results have been analyzed in terms of a theoretical model which assumes an axial composition profile characteristic of diffusion controlled solute redistribution during growth. A comparison of the calculated and measured values suggests a reduction in the applied (empty furnace) temperature gradient by about a factor of three. Values of the interface segregation coefficient (k) determined from the phase diagram, predict values of solute concentration build up in the solid during growth interruptions which are inconsistent with measured results. It appears that the k values used tend to underestimate the actual k values for higher alloy compositions and overestimate k for the lower alloy compositions.

Andrews, R. N.↗
NASA NTRS1991

Acousto-ultrasonic evaluation of ceramic matrix composite materials

Acousto-ultrasonic nondestructive evaluation of ceramic composite specimens with a lithium-alumino-silicate glass matrix reinforced with unidirectional silicon carbide (NICALON) fibers was conducted to evaluate their reserve of strength. Ceramic composite specimens with different amount of damage were prepared by four-point cyclic fatigue loading of the specimens at 500 C for a different number of cycles. The reserve of strength of the specimens was measured as the maximum bending stress recorded during four-pointed bending test with the load monotonically increased until failure occurs. It was observed that the reserve of strength did not correlate with the number of fatigue cycles. However, it was also observed that higher values of the stress wave factor measurements correspond to higher values of the reserve of strength test data. Therefore, these results show that the acousto-ultrasonic approach has the potential of being used to monitor damage and to estimate the reserve of strength of ceramic composites.

Dosreis, Henrique L. M.↗
NASA NTRS1991

Long term integrity for space station power systems

A study was made of the High Temperature Design Codes ASME N47, British R5, and the French RCC-MR Rules. It is concluded that all these codes provide a good basis of design for space application. The new British R5 is the most complete since it deals with the problem of defects. The ASME N47 was subjected longer to practical application and scrutiny. A draft code is introduced, and a proposed draft for high temperature design in which attempts were made to identify gaps and improvements is suggested. The design is limited by creep characteristics. In these circumstances, life is strongly affected by the selected value of the factor of safety. The factor of safety of primary loads adopted in the codes is 1.5. Maybe a lower value of 1.25 is permissible for use in space. Long term creep rupture data for HAYNES 188 is deficient and it is suggested that extrapolation methods be investigated.

Leckie, F. A.↗
NASA NTRS2012

Evaluation of Contrail Reduction Strategies Based on Aircraft Flight Distances

This paper evaluates a set of contrail reduction strategies based on the flight range of aircraft as contrail reduction strategies have different impacts on aircraft depending on how they plan to fly. In general, aircraft with longer flight distances cruise at the altitudes where contrails are more likely to form. The concept of the contrail frequency index is used to quantify contrail impacts. The strategy for reducing the persistent contrail formation is to minimize the contrail frequency index by altering the aircraft's cruising altitude. A user-defined factor is used to trade off between contrail reduction and extra CO2 emissions. A higher value of tradeoff factor results in more contrail reduction and extra CO2 emissions. Results show that contrail reduction strategies using various tradeo factors behave differently from short-range flights to long-range ights. Analysis shows that short-distance flights (less than 500 miles) are the most frequent flights but contribute least to contrail reduction. Therefore these aircraft have the lowest priority when applying contrail reduction strategies. Medium-distance flights (500 to 1000 miles) have a higher priority if the goal is to achieve maximum contrail reduction in total; long-distance flights (1000 to 1500 miles) have a higher priority if the goal is to achieve maximum contrail reduction per flight. The characteristics of transcontinental flights (greater than 1500 miles) vary with different weather days so the priority of applying contrail reduction strategies to the group needs to be evaluated based on the locations of the contrail areas during any given day. For the days tested, medium-distance ights contribute up to 42.6% of the reduction among the groups during a day. The contrail frequency index per 1,000 miles for medium-distance, long-distance, and transcontinental flights can be reduced by an average of 75%. The results provide a starting point for developing operational policies to reduce the impact of aviation on climate based on aircraft flight distances.

Chen, Neil Y.↗
NASA NTRS2021

The Effect of Missing Groups in the Calculation of the Solar Irradiance Deficit: Analysis of the Sunspot Areas from the SOON Network

Sunspot areas are one of the most important indices of solar activity. To obtain an extended time series covering multiple solar cycles one must combine data from different observatories after a proper comparison and calibration of the individual data sets. We compare the daily and group values of sunspot areas provided by the different stations from the Solar Optical Observing Network, SOON, which are determined using similar instruments and techniques. We investigate if there are systematic differences among the stations and whether the differences in the daily values can be attributed to missing groups in the records or errors in the measurements. We find significant differences among the stations of the SOON network in terms of sizes (average daily and group values), quality of observations and coverage (considering number of missing groups and data gaps). Our results indicate that calibration factors for daily values can be used with confidence to combine data sets from different stations. However, for some applications which require the location of the sunspot groups the same correction factors should not be used. We estimate the irradiance deficit due to sunspot through the Photometric Sunspot Index and compare the output from similar data sets to quantify the effect of missing groups. We find differences as high as 150 ppm during the maximum of solar cycle. The effect increases for sunspot groups near the center of the disk accounting for about 80% of the observed differences.

Luis Leuzzi↗
NASA NTRS1976

U.S. Standard Atmosphere, 1976

Part 1 gives the basis for computation of the main tables of atmospheric properties, including values of physical constants, conversion factors, and definitions of derived properties, including values of physical constants, conversion factors, and definitions of derived properties. Part 2 describes the model and data used up to 85 km, in the first section; and the model and data used above 85 km in the second section. The theoretical basis of the high altitude model is given in an appendix. Part 3 contains information on minor constituents in the troposphere, stratosphere, and mesosphere. The main tables of atmospheric properties to 1000 km are given in Part 4. The international system of metric units is used.

Source record↗
NASA NTRS1980

Diffusion in the lower stratosphere as determined from lidar measurements of volcanic aerosol dispersion

Lidar measurements of the stratospheric aerosol layer from the Fuego volcanic eruption in 1974 are analyzed to yield estimates of effective vertical mixing coefficients K(z). The data at 19 deg N latitude give K(z) = 6.6 x 10 to the 2nd sq cm/sec for the altitude range of 19 + or - 1.5 km, while the data at 37 deg N yield K(z) = 13 x 10 to the 2nd sq cm/sec for 19 + or - 3.5 km. The variability in these values is about a factor of 2. These derived K(z) values are interpreted as being due mainly to diffusion.

Remsberg, E. E.↗
NASA NTRS1988

Hot oxygen atoms in the upper atmospheres of Venus and Mars

This paper presents the results of calculations of the hot oxygen atom density values for the upper atmospheres of Venus (computed for solar cycle maximum) and for that of Mars (for solar cycle minimum conditions), using a two stream model to calculate the equilibrium fluxes and energy distribution of the nonthermal component of atomic oxygen. After the energy-dependent hot oxygen fluxes are calculated below the exosphere, the densities above the exobase are obtained using Liouville's equation. The values of hot oxygen atoms calculated for Venus were found to be in good agreement with the values observed by Pioneer Venus Orbiter; the Venus values are about a factor of twenty larger than the calculated values for Mars at the exobase.

Nagy, Andrew↗
NASA NTRS2003

Study of Unsteady Flows with Concave Wall Effect

This paper presents computational fluid dynamic studies of the inlet turbulence and wall curvature effects on the flow steadiness at near wall surface locations in boundary layer flows. The time-stepping RANS numerical solver of the NASA Glenn-HT RANS code and a one-equation turbulence model, with a uniform inlet turbulence modeling level of the order of 10 percent of molecular viscosity, were used to perform the numerical computations. The approach was first calibrated for its predictabilities of friction factor, velocity, and temperature at near surface locations within a transitional boundary layer over concave wall. The approach was then used to predict the velocity and friction factor variations in a boundary layer recovering from concave curvature. As time iteration proceeded in the computations, the computed friction factors converged to their values from existing experiments. The computed friction factors, velocity, and static temperatures at near wall surface locations oscillated periodically in terms of time iteration steps and physical locations along the span-wise direction. At the upstream stations, the relationship among the normal and tangential velocities showed vortices effects on the velocity variations. Coherent vortices effect on the velocity components broke down at downstream stations. The computations also predicted the vortices effects on the velocity variations within a boundary layer flow developed along a concave wall surface with a downstream recovery flat wall surface. It was concluded that the computational approach might have the potential to analyze the flow steadiness in a turbine blade flow.

Wang, Chi R.↗
NASA NTRS1990

Sedimentary Facies Analysis Using AVIRIS Data: A Geophysical Inverse Problem

AVIRIS data can be used to quantitatively analyze and map sedimentary lithofacies. The observed radiance spectra can be reduced to 'apparent reflectance' spectra by topographic and reflectance characterization of several field sites within the image. These apparent reflectance spectra correspond to the true reflectance at each pixel, multiplied by an unknown illumination factor (ranging in value from zero to one). The spatial abundance patterns of spectrally defined lithofacies and the unknown illumination factors can be simultaneously derived using constrained linear spectral unmixing methods. Estimates of the minimum uncertainty in the final results (due to noise, instrument resolutions, degree of illumination and mixing systematics) can be made by forward and inverse modeling. Specific facies studies in the Rattlesnake Hills region of Wyoming illustrate the successful application of these methods.

Boardmann, Joe W.↗