SEARCH · Search NASA

Results for “vertical alignment”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

All sources NASA NTRS DOE OSTI

DOE OSTI2023

A New Plasma Radar Concept for Simultaneous Magnetic and Density Measurements

An innovative, compact 288GHz interferometer has been fabricated, tested, installed and successfully demonstrated on the LAPD-U magnetized plasma at UCLA. The system takes advantage of frequency modulated (FM) radar techniques to deliver a compact heterodyne system. In addition, the reflected power from the source is taken advantage of to eliminate the need for additional quasi-optical components. Electron density in LAPD-U plasma has recently been increased substantially thereby requiring a higher frequency/shorter wavelength interferometer to avoid deleterious refractive effects. This system satisfies those needs. The system uses a 96GHz varactor tuned Gunn oscillator which passes to a passive tripler. This tripler has ~3% conversion efficiency. The 288GHz radiation is then coupled to free space using a so-called dual-mode or Pickett horn. The output 288GHz beam is then coupled to an aspheric lens manufactured from low-loss, high-density polyethylene. This lens is employed to collimate the emerging beam. Small axial adjustment of the lens position can also be used to create a slowly focusing beam so as to optimize the measured signal. In addition, up-down or side-to-side adjustment of the lens can be utilized to steer the beam vertically or horizontally – again to optimize alignment. The propagating beam passes through a beam splitter and then through a water-free, bubble-free fused quartz window into the LAPD-U vacuum vessel. The beam-splitter is a thin sheet of G10 which reflects a small fraction of the incident power (~5 %) towards a zero-bias detector optimized for the frequency range from 220 to 300GHz. Note that waveguides at this frequency have dimensions of ~0.9mm x 0.45mm and so have very large conductive losses. This drives the use of quasi-optical propagation. The detector requires no DC bias and is very responsive (> 1V/mW into 1MΩ). Radiation is coupled to the detector via a similar lens-horn arrangement used for the launch. This reflected beam acts as the local oscillator or reference millimeter-wave beam for the detector. The remainder of the launched source beam then enters the LAPD-U vacuum vessel and passes through the plasma at the mid-plane until reaching the opposing port which is closed off with an aluminum flange. This flange is used as a mirror to retroreflect the incident 288GHz beam back along its path. The retroreflected beam exits the input port but does NOT couple directly into the zero-bias detector. Instead, the majority of the return power continues towards the 288GHz source. As mentioned above the transmitted beam enters the source a second time. This would appear undesirable. However, at these frequencies multipliers are highly non-linear elements which results in a significant portion of the return beam (~20%) re-emerging from the multiplier and horn and then coupling via the G10 beam-splitter to the zero-bias detector. This approach eliminated the need for a second quasi-optical beam-splitter. The system is extremely compact measuring approximately 28 inches x 20 inches. The above did not explain how heterodyne operation was achieved. As mentioned above the Gunn oscillator is able to be varactor tuned. This allows a low voltage to be applied to control the operating frequency of the Gunn oscillator. During heterodyne operation a sawtooth shaped voltage is applied to the varactor at 750kHz using an 80MHz Arbitrary Waveform Generator (AWG). This voltage changes the Gunn frequency linearly during the up-sweep which is then reset abruptly at the sawtooth crash to be immediately followed by another linear sweep. Passage through the 288GHz multiplier triples the frequency change experienced by the electromagnetic wave. These frequency changes are small – tens of megahertz. This FM radar approach results in the launched electromagnetic wave frequencies at the detector for the reference and plasma wave to be different. The approximately 10 ns delay propagation delay for the plasma beam results in the local oscillator and plasma beams NOT having an identical frequency – there is in fact a fixed difference frequency. The frequency tuning level of the Gunn oscillator is then adjusted so that there is ONE cycle of this difference frequency during each linear ramp. During the sawtooth crash or downward re-sweep this one cycle replays in reverse but on a very fast timescale. The process then repeats. Low-pass filtering eliminates the fast re-sweep to leave a pure sine wave heterodyne signal. When the plasma is present it introduces a phase delay in the sine wave (caused by the extremely small Doppler shift resulting from the optical path length change). Of course, to measure this phase change we need a reference. This is simply obtained from an arbitrary waveform generator which provides a synchronized output pulse train which again is low pass filtered to obtain a 750kHz sinusoidal voltage reference for the interferometer. The interferometer was installed on LAPD-U where it has worked reliably and has established that electron densities exceeding 1x10 13 cm -3 are routinely achieved. In addition, the system sensitivity was able to easily observe density fluctuation at frequencies up to 50kHz. FM Radar techniques have enabled a full demonstration of a compact, sensitive, high frequency (288GHz/1mm) heterodyne interferometer.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2019

A new metal transfer process for van der Waals contacts to vertical Schottky-junction transition metal dichalcogenide photovoltaics

Two-dimensional transition metal dichalcogenides are promising candidates for ultrathin optoelectronic devices due to their high absorption coefficients and intrinsically passivated surfaces. To maintain these near-perfect surfaces, recent research has focused on fabricating contacts that limit Fermi-level pinning at the metal-semiconductor interface. Here, we develop a new, simple procedure for transferring metal contacts that does not require aligned lithography. Using this technique, we fabricate vertical Schottky-junction WS 2 solar cells, with Ag and Au as asymmetric work function contacts. Under laser illumination, we observe rectifying behavior and open-circuit voltage above 500 mV in devices with transferred contacts, in contrast to resistive behavior and open-circuit voltage below 15 mV in devices with evaporated contacts. One-sun measurements and device simulation results indicate that this metal transfer process could enable high specific power vertical Schottky-junction transition metal dichalcogenide photovoltaics, and we anticipate that this technique will lead to advances for two-dimensional devices more broadly.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Leveraging FPGA Advantages for Quicker Data Processing for LBNF

The Long Baseline Neutrino Facility (LBNF) will deliver a 2.4 MW muon neutrino beam from Fermilab to the Deep Underground Neutrino Experiment (DUNE), requiring unprecedented precision in beamline alignment to achieve DUNE's neutrino oscillation measurement goals. Vertical misalignments of beamline components as small as 0.5 mm can contribute 6-7\% uncertainty in predicted neutrino flux, necessitating sub-0.1 mm alignment monitoring capabilities. The Horn Location Sensor (HLS) system employs frequency sweep interferometry (FSI) in a distributed hydrostatic leveling network to achieve the required precision under harsh radiation conditions up to 5000 kRad/year. Traditional FSI implementations suffer from laser sweep nonlinearities that degrade resolution and require computationally intensive post-processing corrections using gas reference cells. This work presents a real-time FPGA-based implementation of the HLS data acquisition and processing system using a sweep tracker interferometer for dynamic sweep linearization. The system utilizes a PYNQ-Z2 FPGA with programmable logic implementing parallel 16k-point FFT processing across four channels, synchronized by the sweep tracker signal to eliminate post-processing requirements. Spectral performance testing demonstrates significant improvements in peak sharpness compared to traditional fixed-frequency digitization. The FPGA implementation enables real-time displacement monitoring with processing speeds orders of magnitude faster than software-based approaches, essential for the operational requirements of LBNF's eventual distributed sensor network. This advancement in real-time FSI processing directly supports DUNE's precision neutrino physics program by providing the rapid feedback necessary for maintaining stringent beamline alignment tolerances during high-power beam operations.

Rossel, Jacob↗

DOE OSTI2025

Real-Time FPGA Implementation For Frequency Sweep Interferometry In The LBNF Complex

Rossel, A. Jacob [Fermilab; Unlisted]↗

DOE OSTI2022

Antiproton background of the Mu2e experiment and the vertical misalignment of the Mu2e beamline

Mu2e experiment will search for the neutrinoless µ − → e − conversion in the field of an aluminum nucleus. The total expected background in Mu2e Run I is 0.11 ± 0.03 events, and the antiproton background, 0.01 ± 0.003(stat) ± 0.010(syst), is about 10% of the total. The report discusses the antiproton background of the Mu2e experiment. As it will be explained, the antiproton background is sensitive to the vertical misalignment of the Mu2e beamline. Therefore, it is important to measure the misalignment in situ. The report introduces a data-driven technique of measuring the beamline misalignment. The material is organized as follows. Section 2 describes the Mu2e experiment. Section 3 presents the antiproton background. Section 4 explains the alignment in the apparatus. Section 5 presents the vertical misalignment and a method to measure it from the data. Section 6 presents the initial simulations made and the discussion of the results.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

DOE OSTI2025

How do substituted phenyl-based cations affect the structure-property-stability relationship of low-dimensional perovskites?

Incorporating organic bulky cations in the precursor or post-treatment to achieve two-dimensional/three-dimensional (2D/3D) heterojunction is an effective strategy for enhancing the stability of perovskite materials. However, the issue of insufficient charge transport in 2D perovskites limits their development, and the fundamental mechanism of out-of-plane carrier transport remains unclear. This study designed and synthesized seven organic phenyl-core cations, differentiated at the 1- and 1,4-positions, and identified the impacts on the corresponding properties of the 2D crystalline perovskite. Shorter cations facilitated a more compact arrangement of adjacent inorganic layers, aligning to favor charge transport along the vertical direction. In addition, introducing high electronegativity led to increased intermolecular interactions, resulting in enhanced structural stability and improved phenyl ring π-orbital overlap and interlayer electron coupling, yielding efficient charge transport. Resilience to thermal stressing of the perovskite was strongly correlated with the carbon chain length of the spacer cations. Here, the increase in cation length and the reduction in the rigidity of the amino-terminal both aided in the dispersion of thermal stress in the inorganic framework. Additional hydrogen bonding also contributed to mitigating structural disorder.

14 SOLAR ENERGY↗

DOE OSTI2026

Current status of the electron transport line from RCS to ESR: RTE line

The electron injection system of the U.S. Electron-Ion Collider (EIC) is located outside of the RHIC tunnel. Electrons beams accelerated by the Rapid Cycling Synchrotron (RCS) must be transported to the Electron Storage Ring (ESR), which resides within the RHIC tunnel. To accomplish this, a dedicated beam transport line, referred to as RTE (RCS-to-ESR) line is being designed. The proposed conceptual design comprises three main sections; RCS extraction, a vertical bend and dispersion suppression region, and ESR injection matching. The extraction section uses pulsed kickers and septum magnets to achieve a total deflection angle of 3 degrees. To align the injection section with ESR, the beamline must provide a vertical elevation of 1.68 m, and an array of FODO cells is used to suppress the vertical dispersion. The total length of the RTE line is approximately 133 m, and this paper presents the current design status and considerations for this transport line.

Accelerator Physics↗

DOE OSTI2020

Focusing with saw-tooth refractive lenses at a high-energy X-ray beamline

The Advanced Photon Source 1-ID beamline, operating in the 40–140 keV X-ray energy range, has successfully employed continuously tunable saw-tooth refractive lenses to routinely deliver beams focused in both one and two dimensions to experiments for over 15 years. The practical experience of implementing such lenses, made of silicon and aluminium, is presented, including their properties, control, alignment, and diagnostic methods, achieving ∼1 µm focusing (vertically). Ongoing development and prospects towards submicrometre focusing at these high energies are also mentioned.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2023

1 kV GaN-on-Si Quasi-Vertical Schottky Rectifier

Here, this work demonstrates quasi-vertical GaN Schottky barrier diodes (SBDs) on 6-inch Si substrate with a breakdown voltage (BV) over 1 kV, the highest BV reported in vertical GaN-on-Si SBDs to date. The deep mesa inherently in quasi-vertical devices is leveraged to form a self-aligned edge termination, and the mesa sidewall is covered by the p-type nickel oxide (NiO) as a reduced surface field (RESURF) structure. This novel termination enables a parallel-plane junction electric field of 2.8 MV/cm. The device also shows low turn-on voltage of 0.5 V, and low specific on-resistance of 1.1 mΩ∙ cm 2 . Moreover, the device exhibits excellent overvoltage robustness under the continuous 800 V stress in the unclamped inductive switching test. These results show the good promise of the low-cost vertical GaN-on-Si power diodes.

42 ENGINEERING↗

DOE OSTI2020

Anisotropic Optical and Frictional Properties of Langmuir–Blodgett Film Consisting of Uniaxially-Aligned Rod-Shaped Cellulose Nanocrystals

Langmuir–Blodgett (LB) film deposition gives an opportunity to control the packing density and orientation of anisotropic nanoparticles at a monolayer level, allowing accurate characterization of their anisotropic material properties. Additionally, the uniaxial deposition of rod-shaped cellulose nanocrystals (CNCs) over a macroscopically large area is achieved by aligning the long axis of CNCs on the LB trough with the direction of the maximum drag force within the meniscus during the vertical pulling of the substrate from the LB trough. On the uniaxially-aligned LB films, anisotropic linear and non-linear optical properties of CNCs are obtained using Mueller matrix spectroscopy and sum frequency generation spectroscopy, respectively, and explained with time-dependent density functional theory calculations. Also, the frictional anisotropy of the LB film is measured using atomic force microscopy and explained theoretically. The findings of this study will be valuable for preparation of anisotropic nanoparticle thin films with uniform arrangements and utilization of their anisotropic material properties.

36 MATERIALS SCIENCE↗

DOE OSTI2023

cuAlign: Scalable Network Alignment on GPU Accelerators

Given two graphs, the objective of network alignment is to find the best one-to-one mapping of vertices in one graph (??) to vertices in the other (??), such that the number of overlaps is maximized. We say that edges(??, ??) ???and(??', ??') ??? are overlapped if ?? is mapped to ??' and ?? is mapped to??'. Network alignment is an important optimization problem with several applications in bioinformatics, computer vision and ontology matching. Since it is an NP-hard problem, efficient heuristics and scalable implementations are necessary. In this work, we introduce a new framework that combines the concepts of intra-network proximity using vertex embedding,Belief Propagation (BP) and approximate weighted matching, and provides qualitative improvements up to22%over state-of-the-art approaches. We also provide scalable implementations on GPU accelerators, demonstrating up to19×speedup for Belief Propagation and 3× speedup for approximate weighted matching relative to previous multithreaded implementation. A combination of combinatorial and algebraic kernels within the network alignment algorithm poses significant hurdles for parallelization. Load imbalance and irregular DRAM traffic limit achievable performance on GPUs. Our novel approach identifies and exploits unique structural proper-ties of the BP-based algorithm and employs code fusion to reduce data movement between different steps of the algorithm. Using a diverse set of inputs, we demonstrate qualitative improvements of our algorithms, and performance gains of our GPU-accelerated implementation. We believe that our work will enable algorithmic improvements and practical applications of network alignment.

Xiang, Lizhi↗

DOE OSTI2023

140° Line of Sight (LOS) Mounting Fixture Prototype for ZNeutron Time of Flight (Z-NToF)

The 140° Line of Sight (LOS) Mounting Fixture Prototype for the Z-Neutron Time of Flight diagnostic (Z-NToF) is a prototype support structure for the NToF Jac Black that will be fielded at Sandia’s Z-Machine. The Mounting Fixture will allow the detector to be properly positioned and aligned horizontally from the load, with manual horizontal and vertical translation capabilities, and a limited manual rotation capability. It attaches overhead I-beams at Sandia’s Z machine 140° location approximately 18m from the average source location. The assembly (1011219955) is shown in Figure 1 below. It is capable of rotating ±20° about the vertical axis of the Jac Black detector and translating ±37.5mm horizontally along the Mounting Plate. Vertical adjustments of ±76.2mm can be made using the Lead Screw. Coarser adjustments are possible by changing the number of plates between the I-Beam Hanger Assemblies and the 5in and changing the position of the clamps on the I-beams at Z.

42 ENGINEERING↗

DOE OSTI2026

Investigation of onshore wind farm wake recovery with in situ aircraft measurements during AWAKEN

The share of wind power for electricity supply is increasing worldwide. This highly variable resource requires the improved prediction of power output for network stability. The interaction between wind farm wakes and the atmospheric boundary layer (ABL) introduces uncertainties in power production that warrant detailed investigation. The flow downwind of wind farms is characterized by a reduction in wind speed and an increase in turbulence, which both vary with atmospheric conditions. During the American WAKE experimeNt (AWAKEN), the Technische Universität Braunschweig conducted measurement flights with a research aircraft upwind and downwind of onshore wind farms in the southern Great Plains in Oklahoma in the USA. This study utilizes data from 20 flights conducted at approximately hub height in September 2023 to investigate the wind field variability downwind of the wind farms and vertical profiles to observe atmospheric stratification. The flights were aligned perpendicular to the main wind direction downwind of the King Plains and Armadillo Flats wind farms. Additionally, lidar data from both upwind and downwind ground-based measurement sites and sonic anemometer data were used for comprehensive analysis. Results indicate that under stable ABL conditions, the wake persists at greater downwind distances with a higher velocity deficit in the wake relative to the undisturbed flow compared to unstable stratification. In homogeneous terrain under stable conditions, wake recovery to 95 % occurs between a distance of 4.5 and 9 km downwind of the wind farm. In the semi-complex terrain characterized by shallow hills, slopes, and valleys, the wake exhibits a higher velocity deficit compared to homogeneous terrain, while in some cases the wake was amplified by the terrain resulting in higher velocity deficit 10 km downwind of the wind farm compared to the measurements closer to the wind farm. The turbulent kinetic energy (TKE) and “TKE difference” was found to be a valuable measure in understanding wakes in a semi-complex terrain, showing a clear wake recovery and formation depending on the stratification of the ABL.

17 WIND ENERGY↗

DOE OSTI2024

Atomic-Scale Scanning of Domain Network in the Ferroelectric HfO 2 Thin Film

Ferroelectric HfO 2 -based thin films have attracted much interest in the utilization of ferroelectricity at the nanoscale for next-generation electronic devices. However, the structural origin and stabilization mechanism of the ferroelectric phase are not understood because the film is typically nanocrystalline with active yet stochastic ferroelectric domains. Here, in this study, electron microscopy is used to map the in-plane domain network structures of epitaxially grown ferroelectric Y:HfO 2 films in atomic resolution. The ferroelectricity is confirmed in free-standing Y:HfO 2 films, allowing for investigating the structural origin for their ferroelectricity by 4D-STEM, high-resolution STEM, and iDPC-STEM. At the grain boundaries of <111>-oriented Pca2 1 orthorhombic grains, a high-symmetry mixed-(R3m, Pnm2 1 ) phase is induced, exhibiting enhanced polarization due to in-plane compressive strain. Nanoscale Pca2 1 orthorhombic grains and their grain boundaries with mixed-(R3m, Pnm2 1 ) phases of higher symmetry cooperatively determine the ferroelectricity of the Y:HfO 2 film. It is also found that such ferroelectric domain networks emerge when the film thickness is beyond a finite value. Furthermore, in-plane mapping of oxygen positions overlaid on ferroelectric domains discloses that polarization is suppressed at vertical domain walls, while it is active when domains are aligned horizontally with subangstrom domain walls. In addition, randomly distributed 180° charged domain walls are confined by spacer layers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Modeling Arctic boundary layer cloud streets at grey-zone resolutions

To better understand how model resolution affects the formation of Arctic boundary layer clouds, we investigated the influence of grid spacing on simulating cloud streets that occurred near Utqiagvik (formerly Barrow), Alaska on 2 May 2013 and were observed by the Moderate Resolution Imaging Spectroradiometer (MODIS). The Weather Research and Forecasting model was used to simulate the clouds using nested domains with increasingly fine resolution ranging from a horizontal grid spacing of 27 km in the boundary-layer-parameterized mesoscale domain to a grid spacing of 0.111 km in the large-eddy-permitting domain. We investigated the model-simulated mesoscale environment, horizontal and vertical cloud structures, boundary layer stability, and cloud properties, all of which were subsequently used to interpret the observed roll-cloud case. Increasing model resolution led to a transition from a more buoyant boundary layer to a more shear-driven turbulent boundary layer. The clouds were stratiform-like in the mesoscale domain, but as the model resolution increased, roll-like structures, aligned along the wind field, appeared with ever smaller wavelengths. A stronger vertical water vapor gradient occurred above the cloud layers with decreasing grid spacing. With fixed model grid spacing at 0.333 km, changing the model configuration from a boundary layer parameterization to a large-eddy-permitting scheme produced a more shear-driven and less unstable environment, a stronger vertical water vapor gradient below the cloud layers, and the wavelengths of the rolls decreased slightly. In this study, only the large-eddy-permitting simulation with gird spacing of 0.111 km was sufficient to model the observed roll clouds.

Lai, Hui-Wen↗

DOE OSTI2024

Impact of Dilute DIO Additive on Local Microstructure of Fluorinated, pNDI‐Based Polymer Solar Cells

The performance of all‐polymer solar cells is often enhanced by incorporating solvent additives during solution processing. Here, in particular, blends based on the model all‐polymer system PBDBT:N2200 have been shown to have increased short‐circuit current and fill factor when processed with dilute diiodooctane (DIO). However, the morphological mechanism that drives the increase in performance is often not well understood due to limitations in common characterization techniques. In this study, it is shown that a combination of X‐ray techniques with cryogenic high‐resolution transmission electron microscopy (HRTEM) analysis can provide a quantitative and spatially resolved picture of polymer chain orientation and alignment in all‐polymer blends. It is found that DIO induces vertical phase separation in PBDBT‐2F:F‐N2200 and increases donor crystallite thickness in the pi‐stacking direction leading to an acceptor‐rich film surface. However, it is also shown that DIO does not disrupt the formation of face‐on donor–acceptor interfaces. These findings suggest that dilute DIO primarily affects crystalline domain formation in single component regions as opposed to mixed regions; thus, dilute DIO can impact vertical charge transport pathways without sacrificing donor–acceptor interfacial connectivity.

Cheng, Christina↗

DOE OSTI2020

Comparison of Magnetic Field Emission from Unipolar and Bipolar Coil-Based Wireless Charging Systems

In this study, the leakage magnetic field (LMF) from the unipolar (circular, rectangular, etc.) and bipolar (double-D) coil-based wireless charging systems (WCSs) are investigated and compared. The unipolar and bipolar pads, which are the two most widely adopted charging-pads, have significantly different magnetic field emission characteristics. In this paper, the spatial-distribution and vector-pattern of the leakage magnetic field are studied and compared for similar 11 kW unipolar and bipolar coil-based WCSs. The field emissions are simulated using finite element analysis (FEA) and tested experimentally with an 11 kW bipolar coil-based WCS prototype. The results show that the leakage magnetic field of the unipolar and bipolar pads have widely different vector-orientation and spatial distributions of the leakage magnetic field. The results show that the unipolar coil based WCS has a dominant vertical and the bipolar pads coil-based WCS has dominant horizontally aligned leakage magnetic field. Considering the shielding, the aluminum plate is found highly effective for the unipolar pad and almost ineffective for bipolar pads.

Mohammad, Mostak↗

DOE OSTI2025

Physicochemical and Molecular Insights into the Boundary Layer and Free Troposphere Aerosol Interactions over the Southern Great Plains

Ambient aerosols’ vertical profiles are critical for evaluating the role of aerosols in atmospheric chemistry and radiative transfer, but limited data on these profiles hinders our ability to fully assess their impact on the Earth's radiative balance. Here, in this study, we investigated the size-, time-, and altitude resolved composition of individual particles and bulk molecular composition of particle samples collected by an uncrewed aerial system–ArcticShark over the Southern Great Plains. Single particle microanalysis shows that, the free tropospheric (FT) samples are dominated (56-66%) by carbonaceous sulfate particles, while boundary layer (BL) samples are dominated (57-74%) by carbonaceous particles. Back trajectory simulations suggest that FT particles are likely influenced by long-range transport and have undergone aqueous-phase processing. Conversely, in-situ size distribution data shows evidence of particle growth in the upper BL and just below the FT. This observation may indicate vertical transport of particles from an elevated aerosol layer in the FT, possibly linked to a new particle formation event. This observation is further supported by high resolution molecular composition data, which reveals particle volatility increasing with increasing size, which aligns with the growth event. This study aids in fundamental understanding of the compositional and molecular specificity of vertically resolved organic aerosols to provide insights into particle size evolution for future atmospheric models.

ArcticShark↗