Search NASA⌕ Search

SEARCH · Search NASA

Results for “wake effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Estimation of tunnel blockage from wall pressure signatures: A review and data correlation

A method is described for estimating low speed wind tunnel blockage, including model volume, bubble separation and viscous wake effects. A tunnel-centerline, source/sink distribution is derived from measured wall pressure signatures using fast algorithms to solve the inverse problem in three dimensions. Blockage may then be computed throughout the test volume. Correlations using scaled models or tests in two tunnels were made in all cases. In many cases model reference area exceeded 10% of the tunnel cross-sectional area. Good correlations were obtained regarding model surface pressures, lift drag and pitching moment. It is shown that blockage-induced velocity variations across the test section are relatively unimportant but axial gradients should be considered when model size is determined.

Hackett, J. E.↗
NASA NTRS1980

A spin-recovery parachute system for light general-aviation airplanes

A tail mounted spin recovery parachute system was designed and developed by the NASA Langley Research Center for use on light general aviation airplanes. The system was designed for use on typical airplane configurations, including low wing, single engine, and twin-engine design. A mechanically triggered pyrotechnic slug gun is used to forcibly deploy a pilot parachute which extracts a bag that deploys a ring slot spin recovery parachute. The total system weighs 8.2 kg (18 lb). System design factors included airplane wake effects on parachute deployment, prevention of premature parachute deployment, positive parachute jettison, compact size, low weight, system reliability, and pilot and ground crew safety. Extensive ground tests were conducted to qualify the system. The recovery parachute was used successfully in flight 17 times.

Bradshaw, C.↗
NASA NTRS1980

A spin-recovery parachute system for light general-aviation airplanes

A tail mounted spin recovery parachute system was designed and developed for use on light general aviation airplanes. The system was designed for use on typical airplane configurations, including low wing, high wing, single engine and twin engine designs. A mechanically triggered pyrotechnic slug gun is used to forcibly deploy a pilot parachute which extracts a bag that deploys a ring slot spin recovery parachute. The total system weighs 8.2 kg. System design factors included airplane wake effects on parachute deployment, prevention of premature parachute deployment, positive parachute jettison, compact size, low weight, system reliability, and pilot and ground crew safety. Extensive ground tests were conducted to qualify the system. The recovery parachute was used successfully in flight 17 times.

Bradshaw, C.↗
NASA NTRS1980

Non-Synchronous Whirling Due to Fluid-Dynamic Forces in Axial Turbo-Machinery Rotors

The role of fluid forces acting on the blades of an axial turborotor with regards to whirling was analyzed. The dynamic equations were formulated for the coning mode of an overhung rotor. The exciting forces due to the motion were defined through a set of rotor stability derivatives, and analytical expressions of the aerodynamic contributions were found for the case of small mean stream deflection, high solidity and equivalent flat plate cascade. For a typical case, only backward whirl was indicated when the phase shifting of the rotor wake effect was ignored. A parametric study of the dynamic stability boundary reveals that a reduction in blade stagger angle, mass flow rate, fluid density and an increase in stiffness and external damping are all inductive for improved stability.

Shen, S. F.↗
NASA NTRS1980

A spin-recovery parachute system for light general aviation airplanes

A tail-mounted spin-recovery parachute system has been designed and developed by the NASA Langley Research Center for use on light general aviation airplanes. The system was designed for use on typical airplane configurations, including low-wing, high-wing, single- and twin-engine designs. A mechanically triggered pyrotechnic slug gun is used to forcibly deploy a pilot parachute which extracts a bag that deploys a ring-slot spin-recovery parachute. The total system weighs 8.2 kg (18 lb). System design factors included airplane wake effects on parachute deployment, prevention of premature parachute deployment, positive parachute jettison, compact size, low weight, system reliability, and pilot and ground crew safety. Extensive ground tests were conducted to qualify the system. The recovery parachute has been used successfully in flight 17 times.

Bradshaw, C. F.↗
NASA NTRS1983

PAN AIR modeling studies

PAN AIR is a computer program that predicts subsonic or supersonic linear potential flow about arbitrary configurations. The code's versatility and generality afford numerous possibilities for modeling flow problems. Although this generality provides great flexibility, it also means that studies are required to establish the dos and don'ts of modeling. The purpose of this paper is to describe and evaluate a variety of methods for modeling flows with PAN AIR. The areas discussed are effects of panel density, internal flow modeling, forebody modeling in subsonic flow, propeller slipstream modeling, effect of wake length, wing-tail-wake interaction, effect of trailing-edge paneling on the Kutta condition, well- and ill-posed boundary-value problems, and induced-drag calculations. These nine topics address problems that are of practical interest to the users of PAN AIR.

Towne, M. C.↗
NASA NTRS1984

Interactions between the orbiting Space Shuttle and the ionosphere

This paper presents an analysis of interactions between the Space Shuttle Orbiter and the ionosphere based on thermal plasma data obtained from a Spherical Retarding Potential Analyzer (SRPA) and a Langmuir Probe (LP) flown on the third Space Shuttle flight (STS-3) in March 1982. While previous work on spacecraft-plasma interactions has dealt with wake effects, the present work deals with effects that are seen in ram conditions that have not been previously discussed. One observation is a higher degree of plasma turbulence than has been reported from unmanned spacecraft measurements that manifests itself as a frequency component at 2.2 kHz in the SRPA signal. Also seen are unusually high number densities of what appear to be ions with a mass of at least 30 or 32 amu and a temperature in the range 2000-3000 K. Coincident with the enhanced molecular ion species, the temperature of the thermal electrons is seen elevated to above 5000 K. It is hypothesized that these measurements are evidence for a plasma instability resulting from the motion of the outgassing Orbiter through the ionosphere.

Siskind, D. E.↗
NASA NTRS1984

Report on final recommendations for IMPS engineering-science payload

Six general categories of key scientific and engineering concerns for the interactions measurements payload for shuttle (IMPS) mission are addressed: (1) dielectric charging; (2) material property changes; (3) electromagnetic interference, plasma interactions, and plasma wake effects associated with high-voltage solar arrays and large space structures; (4) radio frequency distortion and nonlinearities due to the enhanced plasma in the shuttle ram/wake; (5) shuttle glow and contamination; and (6) plasma interactions with the space-based radar. Lesser concerns are the interactions associated with EVA; the radiation and SEU effects peculiar to the auroral/polar cap environments; and space debris. The measurements needed to address the concerns associated with the general categories are described and a list of generic investigations capable of making the required measurements, emphasizing the spectrum of measurements necessary to quantize the interactions in the auroral/polar environments are included. A suggested ground-test plan for the IMPS project, a description of proposed follow-on IMPS missions, and a detailed bibliography for each of the interactions discussed are included.

Garrett, H. B.↗
NASA NTRS1987

Comparison of experimental and computational techniques for plane mixing layers

In this paper, results from two experimental and two computational investigations of plane turbulent mixing layers are presented and compared. The experimental results include flow visualization data using the smoke laser technique and mean flow and turbulence measurements obtained with hot X-wires and a two-component LDV. Reasonably good agreement is found among these techniques, at least for turbulence quantities up to second order. Reynolds-averaged computations are successful at capturing the complete evolution of the mixing layer, including wake effects in the near field and approach to self-preservation in the far field. The two-dimensional vortex method shows excellent qualitative and quantitative agreement with measured data for the forced mixing layer. For the unforced layer, the results seem to indicate that a three-dimensional computation may be necessary.

Mehta, R. D.↗
NASA NTRS1988

Development of direct-inverse 3-D methods for applied aerodynamic design and analysis

Several inverse methods have been compared and initial results indicate that differences in results are primarily due to coordinate systems and fuselage representations and not to design procedures. Further, results from a direct-inverse method that includes 3-D wing boundary layer effects, wake curvature, and wake displacement are presented. These results show that boundary layer displacements must be included in the design process for accurate results.

Carlson, Leland A.↗
NASA NTRS1987

Voids in Jovian magnetosphere revisited - Evidence of spacecraft charging

The Voyager 2 Plasma Science Instrument (PLS) measuring cold plasma number density observed about a dozen 'voids', lasting from a few minutes to 20 min, in the vicinity of the Ganymede-orbit crossing, when the low-energy ion and electron fluxes recorded fell to very low levels. Original interpretations associated these 'voids' with Ganymede wake effects. In the present study, the PLS data are reexamined, in conjunction with data from the magnetic field experiment and the low-energy charged particle (LECP) experiment. The LECP data showed that the PLS voids were accompanied by large enhancements of the flux of energetic electrons and ions, while the magnetic data exhibited no systematic signatures. It is suggested that increased energetic electron fluxes in the void regions intermittently charged the spacecraft negatively to values between a few kV and a few tens of kV, and that spacecraft charging could have produce dropouts in the measured cold ion and electron fluxes and enhancements in the measured fluxes of hot particles consistent with the observations.

Khurana, K. K.↗
NASA NTRS1989

Inverse wing design in transonic flow including viscous interaction

Several inverse methods were compared and initial results indicate that differences in results are primarily due to coordinate systems and fuselage representations and not to design procedures. Further, results from a direct-inverse method that includes 3-D wing boundary layer effects, wake curvature, and wake displacement are represented. These results show that boundary layer displacements must be included in the design process for accurate results.

Carlson, Leland A.↗
NASA NTRS1988

Navier-Stokes calculations of hovering rotor flowfields

Unsteady, thin-layer Navier-Stokes equations written in rotor coordinates are solved using a partially flux-split, implicit numerical algorithm to calculate the flowfields of a hovering rotor blade at subsonic and transonic conditions. Numerical results are in good agreement with experimental data for both nonlifting and lifting rectangular blades. For the lifting case, the rotor wake effects are modeled by applying a correction to the geometric angle of attack of the blades. Alternate methods of calculating the hovering rotor flowfields in blade-fixed mode that have the same circulation distribution as a hovering blade are explored. All of the results presented in this paper were computed on a Cray-2 supercomputer.

Srinivasan, G. R.↗
NASA NTRS1988

Navier-Stokes simulations of tip vortices for fixed and rotating helicopter blades

Flowfield and tip vortex results are presented for a hovering rotor blade at subcritical and supercritical flow conditions for both nonlifting and lifting configurations. These results are calculated numerically by solving, in a time-accurate fashion, the unsteady thin layer Navier-Stokes equations written in rotor coordinates. The lifting calculations use an induced downwash correction, estimated from a free wake analysis, to the geometric angle of attack of the blades to account for the wake effect. Comparison of numerical results with the experimental data shows very good agreement for all cases considered. Alternate methods of calculating hovering rotor flowfield as steady state flowfield on isolated fixed-blade that have the same circulation distribution as that of rotor in hover are also explored.

Srinivasan, G. R.↗
NASA NTRS1993

Multibody-plasma interactions - Charging in the wake

Multibody-plasma interactions refers to two or more charged bodies simultaneously interacting with the surrounding plasma as well as each other. This paper concerns a basic type of such interactions in space: the charging of a free flyer in the wake of a large structure. The conditions for severe charging are discussed quantitatively. Computer particle simulations are carried out to obtain the charging potentials in the wake of both floating and biased plate. It is shown that a severe charging zone exists in the near wake of a floating plate within which a free flyer is charged to the KV range under the sun shadow/auroral electron condition. Whether the plate is biased or floating, a large potential difference always exists between the plate and a docking free flyer in the wake. The effects of wake charging on spacecraft docking operations are discussed.

Wang, J.↗
NASA NTRS1993

A novel potential/viscous flow coupling technique for computing helicopter flow fields

The primary objective of this work was to demonstrate the feasibility of a new potential/viscous flow coupling procedure for reducing computational effort while maintaining solution accuracy. This closed-loop, overlapped velocity-coupling concept has been developed in a new two-dimensional code, ZAP2D (Zonal Aerodynamics Program - 2D), a three-dimensional code for wing analysis, ZAP3D (Zonal Aerodynamics Program - 3D), and a three-dimensional code for isolated helicopter rotors in hover, ZAPR3D (Zonal Aerodynamics Program for Rotors - 3D). Comparisons with large domain ARC3D solutions and with experimental data for a NACA 0012 airfoil have shown that the required domain size can be reduced to a few tenths of a percent chord for the low Mach and low angle of attack cases and to less than 2-5 chords for the high Mach and high angle of attack cases while maintaining solution accuracies to within a few percent. This represents CPU time reductions by a factor of 2-4 compared with ARC2D. The current ZAP3D calculation for a rectangular plan-form wing of aspect ratio 5 with an outer domain radius of about 1.2 chords represents a speed-up in CPU time over the ARC3D large domain calculation by about a factor of 2.5 while maintaining solution accuracies to within a few percent. A ZAPR3D simulation for a two-bladed rotor in hover with a reduced grid domain of about two chord lengths was able to capture the wake effects and compared accurately with the experimental pressure data. Further development is required in order to substantiate the promise of computational improvements due to the ZAPR3D coupling concept.

Summa, J. Michael↗
NASA NTRS1961

Aerodynamic Characteristics of Towed Cones Used as Decelerators at Mach Numbers from 1.57 to 4.65

Towed and sting-supported cones were tested in the wake of various payloads at supersonic speeds to determine their drag and stability characteristics. The investigation extended over a Mach number range from 1.57 to 4.65 and included such variables as Reynolds number, cone angle, ratio of cone base diameter to payload base diameter, and trailing distance. The results of this investigation showed that the cones towed in the wake of a symmetrical payload at supersonic speeds, in general, have good drag and stability characteristics if towed in the supersonic flow region. A cone with an included angle between 80 deg and 90 deg will give maximum drag while still maintaining stability in the Mach number region of this investigation. In order to minimize wake effects, the ratio of cone base diameter to payload base diameter should be at least one and preferably around three. A trailing distance of three times the payload base diameter, in most cases, is of sufficient length to avoid low drag and instability of the decelerator.

Charczenko, Nickolai↗
NASA NTRS1994

Navier-Stokes Solutions of Rotor and Rotor-Body Flows

This paper will review the advances made recently in the Navier-Stokes CFD methods to simulate aerodynamics and aeroacoustics of helicopter rotors and rotor-body flows. Although a complete flowfield simulation of full helicopter is currently not feasible with these methods, impressive gains have been made in analyzing individual components of this complex problem in a very detailed manner. The use of the state-of-the-art numerical algorithms in solution methods, in conjunction with powerful supercomputers, like the Cray-2, have enabled noticeable progress to be made in modeling viscous-inviscid interactions, blade-vortex interactions, tip-vortex: simulation and wake effects, as well as high speed impulsive noise in hover and forward flight for isolated rotor blades. This paper will critically evaluate the presently available Euler and Navier-Stokes methods, both finite-difference and finite volume methods using structured and unstructured grids for helicopter applications for accuracy, suitability, and computational efficiency. The review will also include the recent progress made using overset grids to model rotor-body flows. All the material for this review will be drawn from the published material shown below.

Srinivasan, G. R.↗