SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Herein, we report the development of a MOF-semiconductor composite film active for water oxidation at a thermodynamic underpotential.
This presentation characterizes spatial trends in radium (Ra) concentrations, sources, and potential impacts generated from Marcellus Shale produced waters. Here, we combine previously published produced water data with additional Ra activity measurements extracted from residual waste reports submitted to the Pennsylvania Department of Environmental Protection from 2012-2023. This is the largest, spatially referenced compilation of Ra activity measurements from produced water sourced from the Marcellus Shale to date. The median Marcellus Shale produced water Ra activity presented here is 6,906 pCi/L (interquartile range = 12,515 pCi/L). Radium activities in the positively skewed dataset can exceed 30,000 pCi/L in some parts of the state. The regional trends in Ra concentrations and isotopic ratios will be characterized and potential environmental and health implications discussed.
We report the synthesis, characterization, and electrocatalytic water oxidation activity of two cobalt complexes, (6-FP)Co(NO 3 ) 2 (1) (6-FP = 8,8'-(1,2-phenylene)diquinoline) and (5-FP)Co(NO 3 ) 2 (2) (5-FP = 1,2-bis(N-7-azaindolyl)benzene), containing "capping arene" bidentate ligands with nitrogen atom donors. The cobalt complexes 1 and 2 were supported on ordered mesoporous carbon (OMC) by π-π stacking, resulting in heterogenized cobalt materials 6-FP-Co-OMC-1 and 5-FP-Co-OMC-2, respectively, and studied for electrocatalytic water oxidation. We find that 6-FP-Co-OMC-1 exhibits an overpotential of 355 mV for a current density of 10 mA cm -2 and a turnover frequency (TOF) of ~0.53 s -1 at an overpotential of 400 mV at pH 14. 6-FP-Co-OMC-1 exhibits activity that is ~1.6 times that of 5-FP-Co-OMC-2, which gives a TOF of 0.32 s -1 at 400 mV overpotential. The structural stability of the single-atom Co site was demonstrated for 6-FP-Co-OMC-1 using X-ray absorption spectroscopy for the molecular complex supported on OMC, but slow degradation in catalyst activity can be attributed to eventual formation of Co oxide clusters. DFT computations of electrocatalytic water oxidation using the molecular complexes as models provide a description of the catalytic mechanism. These studies reveal that the mechanism for O-O bond formation involves an intermediate Co IV oxo complex that undergoes an intramolecular reductive O-O coupling to form a Co II -OOH species. Further, the calculations predict that the molecular 6-FP-Co structure is more active for electrocatalytic water oxidation than 5-FP-Co, which is consistent with experimental studies of 6-FP-Co-OMC-1 and 5-FP-Co-OMC-2, highlighting the possibility that the ligand structure influences the catalytic activity of the supported molecular catalysts.
Identifying the role of oxide supports in transition metal catalysis is critical toward our understanding of heterogeneous catalysis. The water-gas shift (WGS) reaction is a prototypical example where oxide support dictates catalytic activity, yet the cause for this remains uncertain. Herein, we show that a single descriptor—the equilibrium constant for hydroxyl formation—relates the WGS turnover frequency across disparate oxide supports. The dissimilar equilibrium constant, or oxophilicity, between early and late transition metals exemplify the utility of metal-support interfacial sites to circumvent adsorption-energy scaling restrictions, thereby providing bifunctional gains for the WGS reaction class. In relation, the equilibrium constant for hydroxyl formation is equivalent to the equilibrium constant for the formal heterolytic dissociation of hydrogen, and therefore, reflects the ability of the metal-support interface to participate in hydrogen heterolysis. The ubiquitous coexistence, yet divergent chemical behavior of homo- and heterolytically activated hydrogen renders oxide support identity central toward our understanding of hydrogenation catalysis. This work was supported by the US Department of Energy (DOE), Office of Science, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences, and Biosciences and performed at the Environmental Molecular Sciences Laboratory in (EMSL), which is a DOE Office of Science User Facility located at the Pacific Northwest National Laboratory (PNNL). PNNL is a multiprogram national laboratory operated for DOE by Battelle. Computational resources were provided by a user proposal at the National Energy Research Scientific Computing Center (NERSC), a DOE Office of Science User Facility. N.N. would like to thank Oliver Y. Gutierrez for critical feedback during the final stage of manuscript preparation.
The mu-opioid receptor (MOR), a class A G protein-coupled receptor mediates opioid analgesia and remains a central target for pain therapeutics. While crystal structures of MOR exist, they provide limited insight into the receptor’s dynamic conformational landscape underlying function. Here, we engineered a thermostable water-soluble MOR variant (wsMOR) that retains native-like ligand-binding and activation dynamics. This variant enables high-yield production and detailed solution-phase structural studies that are challenging with membrane-embedded MOR, providing a valuable tool for studying receptor activation and aqueous-phase drug screening. Using a combined computational and experimental approach, we performed long-timescale all-atom molecular dynamics simulations together with neutron scattering and single-molecule FRET, revealing a structurally stable receptor with a diverse ensemble of conformations at different temporal resolutions. In the ligand-free state, wsMOR displayed high conformational flexibility, which decreased upon agonist binding, particularly in transmembrane helix 6, a hallmark of G protein-coupled receptor activation. Positive allosteric modulation and G protein binding further stabilized active-like states. These findings highlight wsMOR’s conformational plasticity across picosecond to millisecond timescales and provide a foundation for structure-guided development of next-generation opioid ligands with improved efficacy and safety.
The role of geometric frustration of water molecules on the rate of water oxidation in the nanoconfined interlayer of manganese-oxide layered materials (birnessite, buserite) is examined in a well-controlled experiment. Calcium buserite is prepared, and used in a split-batch synthetic protocol to prepare calcium birnessite, sodium buserite, and sodium birnessite, and partially dehydrated sodium birnessite. Thus, four samples are prepared in which features effecting catalytic efficiency (defect density, average manganese oxidation state) are controlled, and the main difference is the degree of hydration of the interlayer (two layers of water in buserites vs one layer of water in birnessite). Here, molecular dynamics simulations predict birnessite samples to exhibit geometric water frustration, which facilitates redox catalysis by lowering the Marcus reorganizaiton energy of electron transfer, while buserite samples exhibit traditional intermolecular hydrogen bonding among the two-layer aqeuous region, leading to slower catalytic behavior akin to redox reactions in bulk water. Water oxdiation activity is investigated using chemical and electrochemical techniques, demonstrating and quantifying the role of water frustration in enhancing catalysis. Calculation and experiment demonstrate dehydrated sodium birnessite to be most effective, and calcium buserite the least effective, with a difference in electrocatlytic overpotential of ~750 mV and a ~20-fold difference in turnover number.
We report that metal oxide cluster models of catalyst materials offer a powerful platform for probing the molecular-scale features and interactions that govern catalysis. This perspective gives an overview of studies implementing the combination of anion photoelectron (PE) spectroscopy and density functional theory calculations toward exploring cluster models of metal oxides and metal-oxide supported Pt that catalytically drive the hydrogen evolution reaction (HER) or the water–gas shift reaction. The utility in the combination of these experimental and computational techniques lies in our ability to unambiguously determine electronic and molecular structures, which can then connect to results of reactivity studies. In particular, we focus on the activity of oxygen vacancies modeled by suboxide clusters, the critical mechanistic step of forming proximal metal hydride and hydroxide groups as a prerequisite for H2 production, and the structural features that lead to trapped dihydroxide groups. The pronounced asymmetric oxidation found in heterometallic group 6 oxides and near-neighbor group 5/group 6 results in higher activity toward water, while group 7/group 6 oxides form very specific stoichiometries that suggest facile regeneration. Studies on the trans-periodic combination of cerium oxide and platinum as a model for ceria supported Pt atoms and nanoparticles reveal striking negative charge accumulation by Pt, which, combined with the ionic conductivity of ceria, suggests a mechanism for the exceptionally high activity of this system towards the water–gas shift reaction.
Hydropower is a renewable energy resource that produces electricity from flowing water under pressure. Engineered hydropower structures, such as dams, are used to create a hydraulic head, enabling a turbinegenerator unit to convert pressurized flow into electricity. While hydropower has been a source of renewable energy since antiquity, new development in the United States has slowed in recent decades. Based on recent resource assessments, the largest opportunity to expand hydropower in the United States is from new stream-reach development (i.e., new hydropower development along stream-reaches that do not currently have hydroelectric facilities or other forms of infrastructure, such as dams). Roughly 75% of identified new stream-reach development potential is from low-head sites (less than 30 ft of head), which typically suffer from smaller power densities and higher normalized costs, given economies of scale. Hydropower developers and other stakeholders are thus interested in strategies to reduce initial capital costs while practicing sustainable development to maximize environmental compatibility with minimal disruption to natural aquatic life, sediment, and water flows. Historically, civil works have represented a significant cost driver for new hydropower development, with the foundation system representing a major cost component and source of uncertainty. The foundation system is the collection of engineered structural features (e.g. cutoff trenches, walls, grouting, anchors) constructed at or below the preconstruction ground surface that interfaces between the overlying structures (superstructures) and the bed material below (subsurface). Development of a hydropower foundation system must consider the various characteristics of the surrounding stream environment and subsurface while adhering to the engineering requirements of the superstructure that it supports. The care of water, excavation, and other construction activities are important features of foundation design and construction. The design and construction cost of the foundation system is largely dependent on the site geology and riverbed composition and is influenced by the level of geotechnical assessment required and conducted. Thus, a hydropower facility’s geotechnical foundation is often highly site-specific, with proper site selection and assessment being important to project success. The foundation system is designed to provide structural stability (of the foundation and dam), limit seepage, ensure public safety, and maintain functionality for the project life, during both construction and facility operations. Inadequate foundation or dam design can result in dam failure and the uncontrolled release of significant volumes of water, which could cause a high number of casualties and extensive property damage downstream of the failure. According to the Association of State Dam Safety Officials, approximately 30% of all historical dam failures in the United States are attributed to foundation or abutment defects, and another 20% are attributed to piping or seepage through the embankment, foundation, or abutment. To ameliorate these safety considerations, foundations often require massive amounts of construction material (e.g., grout, concrete, engineered dam fill) and long construction times. Foundation design also requires significant analysis prior to construction because the initial in-stream and abutment subsurface conditions are site-specific, and sufficient data for them often are lacking. Current practice requires on-site assessment, using expensive drilling and invasive and non-invasive investigation methods, to determine the expected cost of foundation material and treatment. Additionally, foundation construction often requires site dewatering (and other care of water activities), which involves constructing temporary diversion structures upstream and often downstream, called cofferdams, and water diversion systems that route water around the construction site. Cofferdams and water diversion systems can drastically increase construction costs and contribute to environmental disruption, including modification of flow patterns and benthic habitats. Given the technical, economic, and environmental challenges associated with hydropower foundations, opportunities exist to improve the current state of practice and to develop new and innovative solutions to Hydropower is a renewable energy resource that produces electricity from flowing water under pressure. Engineered hydropower structures, such as dams, are used to create a hydraulic head, enabling a turbinegenerator unit to convert pressurized flow into electricity. While hydropower has been a source of renewable energy since antiquity, new development in the United States has slowed in recent decades. Based on recent resource assessments, the largest opportunity to expand hydropower in the United States is from new stream-reach development (i.e., new hydropower development along stream-reaches that do not currently have hydroelectric facilities or other forms of infrastructure, such as dams). Roughly 75% of identified new stream-reach development potential is from low-head sites (less than 30 ft of head), which typically suffer from smaller power densities and higher normalized costs, given economies of scale. Hydropower developers and other stakeholders are thus interested in strategies to reduce initial capital costs while practicing sustainable development to maximize environmental compatibility with minimal disruption to natural aquatic life, sediment, and water flows. Historically, civil works have represented a significant cost driver for new hydropower development, with the foundation system representing a major cost component and source of uncertainty. The foundation system is the collection of engineered structural features (e.g. cutoff trenches, walls, grouting, anchors) constructed at or below the preconstruction ground surface that interfaces between the overlying structures (superstructures) and the bed material below (subsurface). Development of a hydropower foundation system must consider the various characteristics of the surrounding stream environment and subsurface while adhering to the engineering requirements of the superstructure that it supports. The care of water, excavation, and other construction activities are important features of foundation design and construction. The design and construction cost of the foundation system is largely dependent on the site geology and riverbed composition and is influenced by the level of geotechnical assessment required and conducted. Thus, a hydropower facility’s geotechnical foundation is often highly site-specific, with proper site selection and assessment being important to project success. The foundation system is designed to provide structural stability (of the foundation and dam), limit seepage, ensure public safety, and maintain functionality for the project life, during both construction and facility operations. Inadequate foundation or dam design can result in dam failure and the uncontrolled release of significant volumes of water, which could cause a high number of casualties and extensive property damage downstream of the failure. According to the Association of State Dam Safety Officials, approximately 30% of all historical dam failures in the United States are attributed to foundation or abutment defects, and another 20% are attributed to piping or seepage through the embankment, foundation, or abutment. To ameliorate these safety considerations, foundations often require massive amounts of construction material (e.g., grout, concrete, engineered dam fill) and long construction times. Foundation design also requires significant analysis prior to construction because the initial in-stream and abutment subsurface conditions are site-specific, and sufficient data for them often are lacking. Current practice requires on-site assessment, using expensive drilling and invasive and non-invasive investigation methods, to determine the expected cost of foundation material and treatment. Additionally, foundation construction often requires site dewatering (and other care of water activities), which involves constructing temporary diversion structures upstream and often downstream, called cofferdams, and water diversion systems that route water around the construction site. Cofferdams and water diversion systems can drastically increase construction costs and contribute to environmental disruption, including modification of flow patterns and benthic habitats. Given the technical, economic, and environmental challenges associated with hydropower foundations, opportunities exist to improve the current state of practice and to develop new and innovative solutions to challenges frequently encountered with traditional approaches. With this understanding, it is critically important to understand and document the current state of practice for hydropower geotechnical foundations, identify key challenges, and define opportunities for innovative solutions. To this end, this report documents the current state of practice across the three main phases of geotechnical foundation development: (1) geotechnical site assessment, (2) design, and (3) construction for hydropower systems. It also describes the major challenges with conventional approaches and identifies opportunities for innovation to reduce hydropower foundations costs, timelines, and risks. Key takeaways from this report include the following: Approximately 80% of available low-head sites are expected to have foundations on soil beds rather than rock beds, suggesting that rockfill and earthfill dams may be the most cost-effective conventional dam type for new projects.; Geotechnical and geologic investigation activities are time-consuming and expensive but are essential to define the parameters and criteria needed for foundation design.; Certain riverbed soil and bedrock types present significant technical challenges or require expensive foundation construction, which can prove financially prohibitive for low-head project development.; Modular hydropower design and prefabricated modular foundations represent a promising but unproven paradigm for new hydropower development. Design and construction approaches using optimized and highly repeatable, reliable components would benefit project cost, time, and risk but require additional research and development.; Temporary construction features for foundations, including cofferdams, water diversion, and water control systems, can prove costly and have inherent construction risk.; For economically viable development, hydropower geotechnical foundations should be limited to 4 to 15% of the project’s total initial capital costs. Many proposed projects have experienced cost overruns attributable to foundation difficulties or surprises during construction. These overruns may have been due to inadequate investigations, lack of adequate engineering effort to tailor the structures to site geology and topography, and/or contractual terms, among other considerations.; Challenges for hydropower foundations and opportunities for innovative technology solutions are identified in the following areas (consistent with the three main phases of foundation development): Geotechnical site assessment, Foundation design and materials, Construction methods and technology. Ultimately, this report aims to provide information about geotechnical foundations for low-head hydropower and to motivate transformative technologies to support hydropower growth.
We present an automatically generated dataset of 15,755 records that were extracted from 47,357 papers. These records contain water-splitting activity in the presence of certain photocatalysts, along with additional information about the chemical reaction conditions under which this activity was recorded. These conditions include any co-catalysts and additives that were present during water splitting, the length of time for which the photocatalytic experiment was conducted, and the type of light source used, including its wavelength. Despite the text extraction of such a wide range of chemical reaction attributes, the dataset afforded good precision (71.2%) and recall (36.3%). These figures-of-merit were calculated based on a random sample of open-access papers from the corpus. Mining such a complex set of attributes required the development of novel techniques in knowledge extraction and interdependency resolution, leveraging inter- and intra-sentence relations, which are also described in this paper. We present a new version (version 2.2) of the chemistry-aware text-mining toolkit ChemDataExtractor, in which these new techniques are included.
Activation of liquids with atmospheric pressure plasmas is being investigated for environmental and biomedical applications. When activating the liquid using gas plasma produced species (as opposed to plasmas sustained in the liquid), a rate limiting step is transport of these species into the liquid. To first order, the efficiency of activating the liquid is improved by increasing the ratio of the surface area of the water in contact with the plasma compared to its volume—often called the surface-to-volume ratio (SVR). Maximizing the SVR then motivates the plasma treatment of thin films of liquids. In this paper, results are discussed from a computational investigation using a global model of atmospheric pressure plasma treatment of thin water films by a dielectric barrier discharge (DBD) sustained in different gases (Ar, He, air, N 2 , O 2 ). The densities of reactive species in the plasma activated water (PAW) are evaluated. The residence time of the water in contact with the plasma is increased by recirculating the PAW in plasma reactor. Longer lived species such as H 2 O 2aq and NO 3 - aq accumulate over time (aq denotes an aqueous species). DBDs sustained in Ar and He are the most efficient at producing H 2 O 2aq , DBDs sustained in argon produces the largest density of NO 3 - aq with the lowest pH, and discharges sustained in O 2 and air produce the highest densities of O 3aq . Finally, comparisons to experiments by others show agreement in the trends in densities in PAW including O 3aq , OH aq , H 2 O 2aq and NO 3 - aq , and highlight the importance of controlling desolvation of species from the activated water.
Perennial bioenergy crops with deep (>1 m) rooting systems, such as switchgrass (Panicum virgatum L.), are hypothesized to increase carbon storage in deep soil. Deeply rooted plants may also affect soil hydrology by accessing deep soil water for transpiration, which can affect soil water content and infiltration in deep soil layers, thereby affecting groundwater recharge. Using stable H and O isotope (δ 2 H and δ 18 O) and 3 H values, we studied the soil water conditions at 20–30 cm intervals to depths of 2.4–3.6 m in paired fields of switchgrass and shallow rooted crops at three sites in the southern Great Plains of North America. We found that soil under switchgrass had consistently higher soil water content than nearby soil under shallow-rooted annual crops by a margin of 15%–100%. Soil water content and isotopic depth profiles indicated that hydraulic redistribution of deep soil water by switchgrass roots explained these observed soil water differences. To our knowledge, these are the first observations of hydraulic redistribution in deeply rooted grasses, and complement earlier observations of dynamic soil water fluxes under shallow-rooted grasses. Hydraulic redistribution by switchgrass may be a strategy for drought avoidance, wherein the plant may actively prevent water limitation. Furthermore, this raises the possibility that deeply rooted grasses may be used to passively subsidize soil water to more shallow-rooted species in inter-cropping arrangements.
Abstract Midwestern cities require forecasts of surface nitrate loads to bring additional treatment processes online or activate alternative water supplies. Concurrently, networks of nitrate monitoring stations are being deployed in river basins, co‐locating water quality observations with established stream gauges. However, tools to evaluate the future value of expanded networks to improve water quality forecasts remains challenging. Here, we construct a synthetic data set of stream discharge and nitrate for the Wabash River Basin—one of the United States’ most nutrient polluted basins—using the established Agro‐IBIS and THMB models. Synthetic data enables rapid, unbiased and low‐cost assessment of potential sensor placements to support management objectives, such as near‐term forecasting. Using the synthetic data, we established baseline 1‐day forecasts for surface water nitrate at 12 cities in the basin using support vector machine regression (SVMR; RMSE 0.48–3.3 ppm). Next, we used the SVMRs to evaluate the improvement in forecast performance associated with deployment of additional nitrate sensors. We identified the optimal sensor placement to improve forecasts at each city, and the relative value of sensors at each candidate location. Finally, we assessed the co‐benefit realized by other cities when a sensor is deployed to optimize a forecast at one city, finding significant positive externalities in all cases. Ultimately, our study explores the potential for machine learning to make near‐term predictions and critically evaluate the improvement realized by expanding a monitoring network. While we use nitrate pollution in the Wabash River Basin as a case study, this approach could be readily applied to any problem where the future value of sensors and network design are being evaluated.
Title (20 words): The investigation of the mechanism for the water splitting by holmium oxide nitrate complex in gas-phase Introduction (120 words): The studies for hydrogen from water splitting is important for clean energy economy as molecular hydrogen is a potential energy carrier. Therefore, understanding the fundamental chemistry of water splitting is essential. The water splitting activated by [Ho(NO3)4]- was previously studied. The suggested mechanism was to first eliminate •NO2 from [Ho(NO3)4]- to make [HoO(NO3)3]-. Then, water was added to form [HoO(NO3)3(H2O)]-, followed by eliminating the •OH to form [HoOH(NO3)3]-. However, we proposed a new mechanism with the formation of [Ho(NO3)3]- prior to the water addition. Once water is added to this intermediate to make [Ho(NO3)3(H2O)]-, the •H is eliminated to form [HoOH(NO3)3]-. Here we have used a labeled experiments with 18-O nitrates. The results to support the new mechanism are discussed.
The factors that control the diverse reactivity of the μ-η 2 :η 2 -peroxo dicopper(II) oxy-intermediates in the coupled binuclear copper proteins remain elusive. In this study, spectroscopic and computational methods reveal H-bonding interactions between active-site waters and the μ-η 2 :η2-peroxide of oxy-tyrosinase, and define their effects on the Cu(II) 2 O 2 electronic structure and O 2 activation.
Water-assisted proton shuttling can promote hydrogenation of polar functional groups, and it is generally believed that such an effect can be hardly applied to hydrogenation of C═C bonds due to the latter's weak interaction with water. Here, we report density functional theory calculations and metadynamics simulations, through which we show a dynamic bifunctional metal–acid site that can be transformed, when interacting with water, into an active configuration for unexpected water-enhanced proton shuttling to C═C bonds. In particular, we investigated B(OH)3 anchored to a Ni catalyst for hydrogenation of cyclohexene in an organic solvent, which showed in experiments an increased rate by 100 times when adding a small amount of water. Metadynamics simulations suggest that a B(OH)3–H2O cluster can form on Ni(111), which promotes the proton transfer in the first hydrogenation step, while the second hydrogenation is still driven by metal-mediated direct H-transfer. The recovery process of B(OH)3–H2O also involves a proton shuttling step. We find that the boric species on the surface serves as an electron reservoir and carries the negative charge to balance the positive charge in the proton transfer steps. This work thus provides fundamental insights into this dynamic transformation process of the metal–acid interface, which can in principle be applied to many other bifunctional systems for hydrogenating non-polar unsaturated groups by engineering the interfacial charge separation.
Small diameter carbon nanotubes show high water-salt permselectivity and low activation barrier for water transport.
The direct formic acid fuel cell holds great promise as a next generation portable power source. In this paper we report an experimental study on Pt and Pd monolayer (Pt* and Pd*) atop the close-packed facet of transition metal substrates (denoted Pt*/M or Pd*/M, where M = Pt, Pd, Ir, Au, Rh and Ru) model catalysts for formic acid oxidation (FAO) and demonstrate a promotional effect on Pt*/Au(111) and Pd*/Pt(111) surfaces. Contrary to findings on monometallic surfaces, in situ infrared reflection adsorption spectroscopy collected during formic acid oxidation at potentials anodic of 375 mV reveal that the poisoning reaction intermediate CO is not formed on the monolayer surfaces, suggesting a promotion of the direct mechanisms of FAO at the expense of the indirect mechanism through CO. Our density functional theory calculations on model surfaces with 1:1 stoichiometry for overlayer to support metal atoms for the thermochemistry of the elementary steps defined by adsorbed CO, OH, COOH, and HCOO on the (111) facet of Pt, PtML/Au, Pd, and PdML/Pt largely attribute the promotional effect observed for the monolayer catalysts to easier removal of CO brought about by easier activation of water, relative to the monometallic catalysts. This synergy between experiments and theory brings us closer to a fundamental understanding of FAO electrocatalysts under reaction conditions, paving the way to achieving more active electrocatalysts possibly with less Pt or Pd; a pre-requisite for the mass commercialization of this technology.
The quest for efficient solar-driven water splitting, a promising avenue for clean fuel production, faces challenges due to limited solar energy conversion efficiency. Traditional approaches study the overall water splitting as two spatially separate half reactions on two unrelated sites, hindering full utilization of photogenerated charge and water molecules. To overcome these limitations, an integrated cluster heterostructure catalyst on InGaN/GaN semiconductor nanowires is proposed for the effective utilization of photogenerated charge carriers and water molecules on the same redox localization. By establishing the fast charge extraction kinetics based on InGaN/GaN nanowires, the integration of Rh and MoRhOx clusters on the nanowire surface enables simultaneous and fast hydrogen/oxygen evolution reactions at the cluster heterostructure. Furthermore, the integrated strategy can enhance the charge redistribution across the heterostructure between the two clusters, further optimizing adsorption of reaction intermediates on each cluster for boosted photocatalytic water splitting activity. Consequently, the integrated heterostructure triggers a 40-fold increased hydrogen production efficiency in an artificial leaf system. This study provides valuable insights for the rational design of advanced heterostructured photocatalysts for water splitting and beyond.