Search NASA⌕ Search

SEARCH · Search NASA

Results for “well fractures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Characterization of crack growth under combined loading

Room-temperature static and cyclic tests were made on 21 aluminum plates in the shape of a 91.4x91.4-cm Maltese cross with 45 deg flaws to develop crack growth and fracture toughness data under mixed-mode conditions. During cyclic testing, it was impossible to maintain a high proportion of shear-mode deformation on the crack tips. Cracks either branched or turned. Under static loading, cracks remained straight if shear stress intensity exceeded normal stress intensity. Mixed-mode crack growth rate data compared reasonably well with published single-mode data, and measured crack displacements agreed with the straight and branched crack analyses. Values of critical strain energy release rate at fracture for pure shear were approximately 50% higher than for pure normal opening, and there was a large reduction in normal stress intensity at fracture in the presence of high shear stress intensity. Net section stresses were well into the inelastic range when fracture occurred under high shear on the cracks.

Feldman, A.↗
NASA NTRS1984

Tensile Fracture of Ductile Materials

For brittle materials, circular voids play an important role relative to fracture, intensifing both tensile and compressive stresses. A maximum intensified tensile stress failure criterion applies quite well to brittle materials. An attempt was made to explore the possibility of extending the approach to the tensile fracture of ductile materials. The three dimensional voids that exist in reality are modelled by circular holes in sheet metal. Mathematical relationships are sought between the shape and size of the hole, after the material is plastically deformed, and the amount of deformation induced. Then, the effect of hole shape, size and orientation on the mechanical properties is considered experimentally. The presence of the voids does not affect the ultimate tensile strength of the ductile materials because plastic flow wipes out the stress intensification caused by them. However, the shape and orientation of the defect is found to play an important role in affecting the strain at fracture.

Pai, D. M.↗
NASA NTRS1991

The characterization of a crack-tip field

The stress intensity factor, K, has been successfully used as a measure of fracture toughness, and stress intensity factor range, Delta K, correlates well with the fatigue crack growth rate. This paper gives a deductive logic to demonstrate rigorously that, in the case of small-scale yielding, K and Delta K are capable of characterizing the elastic-plastic crack-tip field both under a monotonic loading and cyclic fatigue loading. This capability to characterize the entire crack-tip field is the underlying reason for the successful application of K and Delta K to linear fracture mechanics.

Liu, H. W.↗
NASA NTRS1988

Mode 2 fracture mechanics

Current development of high-performance rolling element bearings for aircraft engines (up to 3 million DN, where DN is the product of shaft diameter in millimeters and speed in revolutions per minute) has aroused concern about fatigue crack growth in the inner bearing race that leads to catastrophic failure of the bearing and the engine. A failure sequence was postulated by Srawley, and an analytical program was undertaken to simulate fatigue crack propagation in the inner raceway of such a bearing. A fatigue specimen was developed at NASA by which fatigue data may be obtained relative to the cracking problems. The specimen may be used to obtain either mode 2 data alone or a combination of mixed-mode (1 and 2) data as well and was calibrated in this regard. Mixed-mode fracture data for M-50 bearing steel are presented, and a method for performing reversed-loading tests is described.

Buzzard, Robert J.↗
NASA NTRS1978

Volcanism in the cratered terrain hemisphere of Mars

Four kinds of Martian volcanoes and their prevalences in the cratered terrain hemisphere (generally the southern hemisphere) are described. Patera, which are large low-profile volcanic structures, appear to be either older shield volcanoes or a unique type of volcano. 'Plains' volcanics represent low-volume eruptions that formed cones, low shields, and other small-scale structures. Flood volcanics are produced by high-volume eruptions, post-date the older and more degraded plateau plains, and occur mostly as basin-fill materials. Plateau plains, the Martian intercrater plains, contain many wrinkle ridges and floor-fractured craters. It is suggested that volcanic processes as well as erosional processes have been important in obliterating small Martian craters and that volcanic products may constitute a significant fraction (up to 44%) of the surface rocks in the cratered terrain

Greeley, R.↗
NASA NTRS1999

Reflections of AE Waves in Finite Plates: Finite Element Modeling and Experimental Measurements

The capability of a three-dimensional dynamic finite element method for predicting far-field acoustic emission signals in thin plates of finite lateral extent, including their reflections from the plate edges, was investigated. A lead break (Hsu-Neilsen) source to simulate AE was modeled and used in the experimental measurements. For the thin plate studied, the signals were primarily composed of the lowest order symmetric (S0) and antisymmetric (A0) Lamb modes. Experimental waveforms were detected with an absolutely calibrated, wideband, conical element transducer. The conditions of lead fractures both on the surface of the plate as well as on the edge of the plate were investigated. Surface lead breaks preferentially generate the A0 mode while edge lead breaks generate the S0 mode. Reflections of developed plate waves from both normal and oblique incidence angles were evaluated. Particularly interesting for the case of the lead break on the plate edge were S0 waves produced by the interaction of a Rayleigh wave with the plate corner and by a bulk shear wave mode converting at the side edge. The Rayleigh wave, in this case, propagated along the specimen edge. For all cases considered, the experimental measurements were in good agreement with the predictions of the finite element model.

Prosser, W. H.↗
NASA NTRS2006

Simulated Data for High Temperature Composite Design

The paper describes an effective formal method that can be used to simulate design properties for composites that is inclusive of all the effects that influence those properties. This effective simulation method is integrated computer codes that include composite micromechanics, composite macromechanics, laminate theory, structural analysis, and multi-factor interaction model. Demonstration of the method includes sample examples for static, thermal, and fracture reliability for a unidirectional metal matrix composite as well as rupture strength and fatigue strength for a high temperature super alloy. Typical results obtained for a unidirectional composite show that the thermal properties are more sensitive to internal local damage, the longitudinal properties degrade slowly with temperature, the transverse and shear properties degrade rapidly with temperature as do rupture strength and fatigue strength for super alloys.

Chamis, Christos C.↗
NASA NTRS1981

Correlation of LANDSAT lineaments with Devonian gas fields in Lawrence County, Ohio

In an effort to locate sources of natural gas in Ohio, the fractures and lineaments in Black Devonian shale were measured by: (1) field mapping of joints, swarms, and fractures; (2) stereophotointerpretation of geomorphic lineaments with precise photoquads; and (3) by interpreting the linear features on LANDSAT images. All results were compiled and graphically represented on 1:250,000 scale maps. The geologic setting of Lawrence County was defined and a field fracture map was generated and plotted as rose patterns at the exposure site. All maps were compared, contrasted, and correlated by superimposing each over the other as a transparency. The LANDSAT lineaments had significant correlation with the limits of oil and gas producing fields. These limits included termination of field production as well as extensions to other fields. The lineaments represent real rock fractures with zones of increased permeability in the near surface bedrock.

Johnson, G. O.↗
NASA NTRS1976

An automated procedure for preliminary design of primary structure for transport Aircraft

A multistation structural synthesis procedure, designed to perform structural sizing and detail design of boxbeam structure, is presented. The design procedure combines the use of an iterative sizing technique for distributing material to structural elements with a nonlinear programming technique to finding efficient structural element designs of a given weight. Constraints based on fatigue and fracture criteria and static strength criteria under multiple loading conditions are considered, as well as constraints on the upper and lower bounds of the actual design variables. Emphasis is placed on the overall design procedure and the technique used to include the fatigue and fracture criteria.

Kruse, G. S.↗
NASA NTRS1987

The friction and wear of TPS fibers

The sliding friction behavior of single filaments of SiO2, SiC, and an aluminoborosilicate has been determined. These fibers are used in thermal protection systems (TPS) and are subject to damage during weaving and aero-maneuvering. All fibers exhibited stick-slip friction indicating the successive formation and rupture of strong junctions between the contacting filaments. The static frictional resistance of the sized SiC filament was 4X greater than for the same filament after heat cleaning. This result suggests that the sizing is an organic polymer with a high shear yield strength. Heat cleaning exposes the SiC surface and/or leaves an inorganic residue so that the adhesional contact between filaments has a low fracture energy and frictional sliding occurs by brittle fracture. The frictional resistances of the sized and heat cleaned SiO2 and glass filaments were all comparable to that of the heat cleaned SiC. It would appear that the sizings as well as the heat cleaned surfaces of the silica and glass have low fracture energies so that the sliding resistance is determined by brittle fracture.

Bascom, W. D.↗
NASA NTRS1973

Combined effects of weld-induced residual stresses and flaws on the fracture strength of Ti-5Al-2.5Sn

The combined effects of weld-induced residual stresses and flaws on fracture strength were experimentally evaluated by testing Ti-5Al-2.5Sn surface flawed specimens at -320F (-195C) in liquid nitrogen. Flaws were located in weld metal with crack planes either parallel to or perpendicular to gas tungsten arc weld centerlines, and in base metal with the crack plane perpendicular to the rolling direction. Tests were conducted using two different flaw sizes to effect fracture stresses at two different levels including one level either at or near, and one level well below the tensile yield strength. Three different residual stress levels were generated, measured, and tested. Results were evaluated using modified linear elastic fracture mechanics theory.

Hall, L. R.↗
NASA NTRS2004

Formulations for Stronger Solid Oxide Fuel-Cell Electrolytes

Tests have shown that modification of chemical compositions can increase the strengths and fracture toughnesses of solid oxide fuel-cell (SOFC) electrolytes. Heretofore, these solid electrolytes have been made of yttria-stabilized zirconia, which is highly conductive for oxygen ions at high temperatures, as needed for operation of fuel cells. Unfortunately yttria-stabilized zirconia has a high coefficient of thermal expansion, low resistance to thermal shock, low fracture toughness, and low mechanical strength. The lack of strength and toughness are especially problematic for fabrication of thin SOFC electrolyte membranes needed for contemplated aeronautical, automotive, and stationary power-generation applications. The modifications of chemical composition that lead to increased strength and fracture toughness consist in addition of alumina to the basic yttria-stabilized zirconia formulations. Techniques for processing of yttria-stabilized zirconia/alumina composites containing as much as 30 mole percent of alumina have been developed. The composite panels fabricated by these techniques have been found to be dense and free of cracks. The only material phases detected in these composites has been cubic zirconia and a alumina: this finding signifies that no undesired chemical reactions between the constituents occurred during processing at elevated temperatures. The flexural strengths and fracture toughnesses of the various zirconia-alumina composites were measured in air at room temperature as well as at a temperature of 1,000 C (a typical SOFC operating temperature). The measurements showed that both flexural strength and fracture toughness increased with increasing alumina content at both temperatures. In addition, the modulus of elasticity and the thermal conductivity were found to increase and the density to decrease with increasing alumina content. The oxygen-ion conductivity at 1,000 C was found to be unchanged by the addition of alumina.

Bansal, Narottam P.↗
NASA NTRS2004

Investigation of Three-Dimensional Stress Fields and Slip Systems for FCC Single Crystal Superalloy Notched Specimens

Metals and their alloys, except for a few intermetallics, are inherently ductile, i.e. plastic deformation precedes fracture in these materials. Therefore, resistance to fracture is directly related to the development of the plastic zone at the crack tip. Recent studies indicate that the fracture toughness of single crystals depends on the crystallographic orientation of the notch as well as the loading direction. In general, the dependence of crack propagation resistance on crystallographic orientation arises from the anisotropy of (i) elastic constants, (ii) plastic deformation (or slip), and (iii) the weakest fracture planes (e.g. cleavage planes). Because of the triaxial stress state at the notch tips, many slip systems that otherwise would not be activated during uniaxial testing, become operational. The plastic zone formation in single crystals has been tackled theoretically by Rice and his co-workers and only limited experimental work has been conducted in this area. The study of the stresses and strains in the vicinity of a FCC single crystal notch tip is of relatively recent origin. We present experimental and numerical investigation of 3D stress fields and evolution of slip sector boundaries near notches in FCC single crystal tension test specimens, and demonstrate that a 3D linear elastic finite element model that includes the effect of material anisotropy is shown to predict active slip planes and sectors accurately. The slip sector boundaries are shown to have complex curved shapes with several slip systems active simultaneously near the notch. Results are presented for surface and mid-plane of the specimens. The results demonstrate that accounting for 3D elastic anisotropy is very important for accurate prediction of slip activation near FCC single crystal notches loaded in tension. Results from the study will help establish guidelines for fatigue damage near single crystal notches.

Arakere, Nagaraj K.↗
NASA NTRS1991

An equivalent domain integral method for three-dimensional mixed-mode fracture problems

A general formulation of the equivalent domain integral (EDI) method for mixed mode fracture problems in cracked solids is presented. The method is discussed in the context of a 3-D finite element analysis. The J integral consists of two parts: the volume integral of the crack front potential over a torus enclosing the crack front and the crack surface integral due to the crack front potential plus the crack face loading. In mixed mode crack problems the total J integral is split into J sub I, J sub II, and J sub III representing the severity of the crack front in three modes of deformations. The direct and decomposition methods are used to separate the modes. These two methods were applied to several mixed mode fracture problems, were analyzed, and results were found to agree well with those available in the literature. The method lends itself to be used as a post-processing subroutine in a general purpose finite element program.

Shivakumar, K. N.↗
NASA NTRS1992

An equivalent domain integral method for three-dimensional mixed-mode fracture problems

A general formulation of the equivalent domain integral (EDI) method for mixed mode fracture problems in cracked solids is presented. The method is discussed in the context of a 3-D finite element analysis. The J integral consists of two parts: the volume integral of the crack front potential over a torus enclosing the crack front and the crack surface integral due to the crack front potential plus the crack face loading. In mixed mode crack problems the total J integral is split into J sub I, J sub II, and J sub III representing the severity of the crack front in three modes of deformations. The direct and decomposition methods are used to separate the modes. These two methods were applied to several mixed mode fracture problems, were analyzed, and results were found to agree well with those available in the literature. The method lends itself to be used as a post-processing subroutine in a general purpose finite element program.

Shivakumar, K. N.↗
NASA NTRS1998

Methodology for Predicting the Onset of Widespread Fatigue Damage in Lap-Splice Joints

NASA has conducted an Airframe Structural Integrity Program to develop the methodology to predict the onset of widespread fatigue damage to lap-splice joints of fuselage structures. Several stress analysis codes have been developed or enhanced to analyze the lap-splice-joint configuration. Fatigue lives in lap-splice-joint specimens and fatigue-crack growth in a structural fatigue test article agreed well with calculations from small-crack theory and fatigue-crack growth analyses with the FASTRAN code. Residual-strength analyses of laboratory specimens and wide stiffened panels were predicted quite well from the critical crack-tip-opening angle (CTOA) fracture criterion and elastic-plastic finite-element analyses (two- or three-dimensional codes and the STAGS shell code).

Newman, J. C., Jr.↗
NASA NTRS2001

Differential expression of neuroleukin in osseous tissues and its involvement in mineralization during osteoblast differentiation

Osteoblast differentiation is a multistep process that involves critical spatial and temporal regulation of cellular processes marked by the presence of a large number of differentially expressed molecules. To identify key functional molecules, we used differential messenger RNA (mRNA) display and compared RNA populations isolated from the defined transition phases (proliferation, matrix formation, and mineralization) of the MC3T3-E1 osteoblast-like cell line. Using this approach, a complementary DNA (cDNA) fragment was isolated and identified as neuroleukin (NLK), a multifunctional cytokine also known as autocrine motility factor (AMF), phosphoglucose isomerase (PGI; phosphohexose isomerase [PHI]), and maturation factor (MF). Northern analysis showed NLK temporal expression during MC3T3-E1 cell differentiation with a 3.5-fold increase during matrix formation and mineralization. Immunocytochemical studies revealed the presence of NLK in MC3T3-E1 cells as well as in the surrounding matrix, consistent with a secreted molecule. In contrast, the NLK receptor protein was detected primarily on the cell membrane. In subsequent studies, a high level of NLK expression was identified in osteoblasts and superficial articular chondrocytes in bone of 1-, 4-, and 8-month-old normal mice, as well as in fibroblasts, proliferating chondrocytes, and osteoblasts within a fracture callus. However, NLK was not evident in hypertrophic chondrocytes or osteocytes. In addition, treatment of MC3T3 cells with 6-phosphogluconic acid (6PGA; a NLK inhibitor) resulted in diminishing alkaline phosphatase (ALP) activity and mineralization in MC3T3-E1 cells, especially during the matrix formation stage of differentiating cells. Taken together, these data show specific expression of NLK in discrete populations of bone and cartilage cells and suggest a possible role for this secreted protein in bone development and regeneration.

NASA Discipline Musculoskeletal↗