Search NASA⌕ Search

SEARCH · Search NASA

Results for “wing sections”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1922

Problem of the slotted wing : a communication from the Aerodynamic Institute of the Aachen Technical High School

It is to be expected that the advantageous properties, hitherto discovered in many slotted wing sections, depend very largely on the contour of the slot and the structural details of the wing. It is therefore of interest, aside from measurements on wings of constant cross-section along the span, to measure also wing models in which the structural details have already been given practical consideration.

WINGS - EXPERIMENTS↗
NASA NTRS1985

An asymptotic theory for the interference of large aspect ratio swept wings and multiple propeller slipstreams

This paper presents an asymptotic method for the analysis of the interference of multiple tractor propeller slipstream with large aspect ratio swept wings. It is assumed that the height of the slipstream is of the order of the wing chord and its spanwise extent is of the order of the wing span. Three different flow regions are identified by employing different stretching transformations. Asymptotic expansions are made in each of the three regions, using the chord to span ratio as the small expansion parameter. The details of the nonuniform flow in the slipstream enter into the wing sectional analysis. In the outer limit, the wing shrinks to a swept lifting line, and the slipstream reduces to a thin sheet of jet carrying the momentum gain from the propeller. The curvature of this jet sheet results in a pressure difference which is represented by a vortex sheet. The governing equations are solved by discretization. Several examples are considered for which experimental data are available. Comparison of the present results with the experimental data as well as other numerical solutions showed generally good agreement.

Prabhu, R. K.↗
NASA NTRS1952

Effect of Compressibility on the Flow past a Two-dimensional Bump

An investigation has been conducted to determine experimentally the effects of compressibility on the flow past a bump and to compare the experimentally determined results with theory. Pressure measurements and Schlieren photographs were made of the flow past two bumps having thickness-chord ratios of 0.10 and 0.30 at Mach numbers between 0.20 and 0.84

FLOW, SUBSONIC↗
NASA NTRS1955

Lift on a bent, flat plate

The lift on a bent, flat plate is calculated exactly by the use of conformal mapping. Results are presented in terms permitting direct determination of the angle of zero lift, the lift coefficient, and the lift-curve slope for any flap-chord ratio, flap-deflection angle, and angle of attack.

WING FLAPS - DEFLECTION↗
NASA NTRSDate not supplied

Transonic Correction Method for Flight Dynamic Stability Analysis of Mach 0.745 Transonic Truss-Braced Wing

This paper presents a transonic correction method for obtaining dynamic stability derivatives for flight dynamic stability analysis. The method provides a transonic correction to the Theodorsen's theory of unsteady aerodynamics using FUN3D CFD solver of unsteady Reynolds-averaged Navier-Stokes equations (RANS) for a series of wing sections of the Mach 0.745 Transonic Truss-Braced Wing in pitch and plunge oscillations. Unsteady lift and pitching moment coefficients are obtained and used to develop the correction terms in the Theodorsen's theory to account for transonic aerodynamics. The unsteady lift and pitching moment derivatives with respect to the unsteady angle of attack are obtained as frequency response functions of the reduced frequency. These frequency response functions are used to compute the dynamic stability derivatives of lift and pitching moment due to the angle of attack and pitch rate and the dynamic stability derivatives for the rolling moment and yawing moment with respect to the roll rate and yaw rate. A transonic correction is applied to steady-state stability derivatives computed by VSPAERO solver using transonic small disturbance code TSFOIL coupled to an integral boundary method. A dynamic stability analysis is conducted for longitudinal and lateral-directional motions. Without transonic corrections and dynamic stability derivatives, the analysis indicates an unstable phugoid mode. The transonic correction applied to the steady-state stability derivatives computed by VSPAERO shows a stable phugoid mode. This is due to the increase of the drag stability derivatives as a result of the additional wave drag contribution in transonic flow. The effect of the transonic dynamic stability derivatives is observed to be a significant contributor to the increase in the damping values of all the flight dynamic modes of the Mach 0.745 Transonic-Truss Braced Wing.

Transonic↗
NASA NTRSDate not supplied

Dynamic Aeroelastic Flight Dynamic Modeling of Mach 0.745 Transonic Truss-Braced Wing

This paper presents a modeling approach for dynamic aeroelastic flight dynamic analysis of the Mach0.745 Transonic Truss-Braced Wing. The modeling approach is based on a transonic correction method to correct the Theodorsen’s theory for transonic flow. CFD unsteady Reynolds-averaged Navier-Stokes equations (RANS) simulations are conducted using FUN3D solver for a series of wing sections from the Mach 0.745Transonic Truss-Braced Wing in pitch and plunge oscillations. Unsteady lift and pitching moment coefficients are obtained and used to develop the correction terms in the Theodorsen’s theory to account for transonic aerodynamics. The unsteady lift and pitching moment derivatives with respect to the unsteady angle of attack are obtained as functions of the reduced frequency. These derivatives are used to compute the unsteady lift and pitching moment contributions by the angle of attack, pitch rate, and roll rate. They are then approximated using a frequency-domain regression to obtain the dynamic stability derivatives for the Mach 0.745 Transonic Truss-Braced Wing. The structural dynamic mode shapes of the Mach 0.745 TTBW are extracted from a NAS-TRAN finite-element model. These mode shapes are used to compute the generalized unsteady aerodynamic forces. The aerodynamic mass, damping, and stiffness and the aerodynamic lag states are constructed to couple the dynamic aeroelastic contribution to the flight dynamic model of the Mach 0.745 Transonic Truss-Braced Wing. The coupled dynamic aeroelastic flight dynamic equations of motion are formulated. The eigenvalues of the coupled system are computed. All the flight dynamic modes and structural dynamic modes are stable at Match 0.745. The effect of transonic aerodynamics generally causes all the dynamic modes to have lower damping values

Flight Dynamics↗
NASA NTRS1985

Leading-edge design for improved spin resistance of wings incorporating conventional and advanced airfoils

Discontinuous wing leading-edge droop designs have been evaluated as a means of modifying wing autorotative characteristics and thus improving airplane spin resistance. Addition of a discontinuous outboard wing leading-edge droop to three typical light airplanes having NACA 6-series wing sections produced significant improvements in stall characteristics and spin resistance. Wind tunnel tests of two wings having advanced natural laminar flow airfoil sections indicated that a discontinuous leading-edge droop can delay the onset of autorotation at high angles of attack without adversely affecting the development of laminar flow at cruise angles of attack.

Stough, H. P., III↗
NASA NTRS1989

Wind-tunnel investigation of aerodynamic characteristics and wing pressure distributions of an airplane with variable-sweep wings modified for laminar flow

A wind tunnel test was conducted to evaluate the aerodynamic characteristics and wing pressure distributions of a variable wing sweep aircraft having wing panels that are modified to promote laminar flow. The modified wing section shapes were incorporated over most of the exposed outer wing panel span and were obtained by extending the leading edge and adding thickness to the existing wing upper surface forward of 60 percent chord. Two different wing configurations, one each for Mach numbers 0.7 and 0.8, were tested on the model simultaneously, with one wing configuration on the left side and the other on the right. The tests were conducted at Mach numbers 0.20 to 0.90 for wing sweep angles of 20, 25, 30, and 35 degrees. Longitudinal, lateral and directional aerodynamic characteristics of the modified and baseline configurations, and selected pressure distributions for the modified configurations, are presented in graphical form without analysis. A tabulation of the pressure data for the modified configuration is available as microfiche.

Hallissy, James B.↗
NASA NTRS1977

F-8 supercritical wing flight pressure, Boundary layer, and wake measurements and comparisons with wind tunnel data

Data for speeds from Mach 0.50 to Mach 0.99 are presented for configurations with and without fuselage area-rule additions, with and without leading-edge vortex generators, and with and without boundary-layer trips on the wing. The wing pressure coefficients are tabulated. Comparisons between the airplane and model data show that higher second velocity peaks occurred on the airplane wing than on the model wing. The differences were attributed to wind tunnel wall interference effects that caused too much rear camber to be designed into the wing. Optimum flow conditions on the outboard wing section occurred at Mach 0.98 at an angle of attack near 4 deg. The measured differences in section drag with and without boundary-layer trips on the wing suggested that a region of laminar flow existed on the outboard wing without trips.

Montoya, L. C.↗
NASA NTRS1973

Noise tests of a model engine-over-the-wing STOL configuration using a multijet nozzle with deflector

Noise data were obtained with a small scale model stationary STOL configuration that used an eight lobe mixer nozzle with deflector mounted above a 32-cm-chord wing section. The factors varied to determine their effect upon the noise were wing flap angle, nozzle shape, nozzle location, deflector configuration, and jet velocity. The noise from the mixer nozzle model was compared to the noise from a model using a circular nozzle of the same area. The mixer nozzle model was quieter at the low to middle frequencies, while the circular nozzle was quieter at high frequencies. The perceived noise level (PNL) was calculated for an aircraft 10 times larger than the model. The PNL at 500 feet for the mixer nozzle turned out to be within 1 db of the PNL for the circular nozzle. For some configurations at highly directional broadband noise, which could be eliminated by changes in nozzle and/or deflector location, occurred below the wing.

Olsen, W. A.↗
NASA NTRS1975

Evaluation of viscous drag reduction schemes for subsonic transports

The results are described of a theoretical study of viscous drag reduction schemes for potential application to the fuselage of a long-haul subsonic transport aircraft. The schemes which were examined included tangential slot injection on the fuselage and various synergetic combinations of tangential slot injection and distributed suction applied to wing and fuselage surfaces. Both passive and mechanical (utilizing turbo-machinery) systems were examined. Overall performance of the selected systems was determined at a fixed subsonic cruise condition corresponding to a flight Mach number of free stream M = 0.8 and an altitude of 11,000 m. The nominal aircraft to which most of the performance data was referenced was a wide-body transport of the Boeing 747 category. Some of the performance results obtained with wing suction are referenced to a Lockheed C-141 Star Lifter wing section. Alternate designs investigated involved combinations of boundary layer suction on the wing surfaces and injection on the fuselage, and suction and injection combinations applied to the fuselage only.

Marino, A.↗
NASA NTRS1931

Investigation of certain wing shapes with sections varying progressively along the span

This investigation has a double object: 1) the calculation of the general characteristics of certain wings with progressively varying sections; 2) the determination of data furnishing, in certain cases, some information on the actual distribution of the external forces acting on a wing. We shall try to show certain advantages belonging to the few wing types of variable section which we shall study and that, even if the general aerodynamic coefficients of these wings are not often clearly superior to those of certain wings of uniform section, the wings of variable section nevertheless have certain advantages over those of uniform section in the distribution of the attainable stresses.

Arsandaux, L↗
NASA NTRS1950

The Effect of Nonuniform Temperature Distributions on the Stresses and Distortions of Stiffened-Shell Structures

The structural effects of nonuniform temperature distributions, such as those produced by aerodynamic heating or thermal ice-prevention systems, are discussed and found to be of two types: The introduction of thermal stresses and distortions as a result of restrained thermal expansion and a change in the stresses and distortions produced by the applied loads as a result of the variation of elastic properties of materials with temperature. These effects are illustrated by sample analyses of the stress and distortion distributions of simple box beams and by calculation of the stresses on a typical wing section.

ALUMINUM ALLOYS - ALCOA 75ST6 - ELASTICITY↗
NASA NTRS1980

Induced drag ideal efficiency factor of arbitrary lateral-vertical wing forms

A relatively simple equation is presented for estimating the induced drag ideal efficiency factor e for arbitrary cross sectional wing forms. This equation is based on eight basic but varied wing configurations which have exact solutions. The e function which relates the basic wings is developed statistically and is a continuous function of configuration geometry. The basic wing configurations include boxwings shaped as a rectangle, ellipse, and diamond; the V-wing; end-plate wing; 90 degree cruciform; circle dumbbell; and biplane. Example applications of the e equations are made to many wing forms such as wings with struts which form partial span rectangle dumbbell wings; bowtie, cruciform, winglet, and fan wings; and multiwings. Derivations are presented in the appendices of exact closed form solutions found of e for the V-wing and 90 degree cruciform wing and for an asymptotic solution for multiwings.

Deyoung, J.↗
NASA NTRS1921

The Factors that Determine the Minimum Speed of an Airplane

The author argues that because of a general misunderstanding of the principles of flight at low speed, there are a large number of airplanes that could be made to fly several miles per hour slower than at present by making slight modifications. In order to show how greatly the wing section affects the minimum speed, curves are plotted against various loadings. The disposition of wings on the airplane slightly affects the lift coefficient, and a few such cases are discussed. Another factor that has an effect on minimum speed is the extra lift exerted by the slip stream on the wings. Also discussed are procedures to be followed by the pilot, especially with regard to stick movements during low speed flight. Also covered are stalling, yaw, rolling moments, lateral control, and the effectiveness of ailerons and rudders.

AIRPLANES - SPEED AND POWER AIRPLANE - SPEED↗
NASA NTRS1923

The Nichols Wing Cutting Equipment

Described here is wing cutting equipment for the economical production of metal wings for wind tunnel models. The machine will make any size of constant-section wing or strut up to one-sixth inch chord by 36-inch span and up to a thickness of one and one-quarter inches. It cuts a smooth, true model that is accurate to within two-thousandths of an inch on any ordinate. The holding jaws are so designed as to leave the model free of chip marks, and the only hand finishing necessary after the cutting is a rub with amunite to remove burrs. The actual change on ordinate in this finishing rub is less than .0002 inches.

Ford, James B↗
NASA NTRS1980

Propeller slipstream/wing interaction in the transonic regime

An inviscid model for the interaction between a thin wing and a nearly uniform propeller slipstream is presented. The model allows the perturbation velocities due to the interaction to be potential although the undisturbed slipstream velocity is rotational. A finite difference scheme is used to solve the governing equation. Numerical examples indicate that the slipstream has a strong effect on the aerodynamic properties of the wing section within the slipstream and lesser effects elsewhere. The slipstream swirling motion strongly affects the wing load distribution, however, its effect on the wing's total lift and wave drag is small. The axial velocity increment in the slipstream has a small effect on the wing lift, however, it causes a large increase in wave drag.

Rizk, M. H.↗
NASA NTRS1982

Comprehensive missile aerodynamics programs for preliminary design

Two different classes of missile aeroprediction programs have been recently developed. The first class of programs provides rapid engineering predictions and includes MISSILE1 and MISSILE2 applicable to missile configurations with axisymmetric bodies. The second class of programs consists of the DEMON series, including a simplified version NSWCDM, designed to calculate detailed loadings acting on supersonic missiles which may have non-circular body cross sections. Both classes account for high angles of attack and track vortices from canard or wing section to the tail section. Extensive comparisons with experimental data are presented including nonlinear effects of canard control.

Dillenius, M. F. E.↗