Search NASA⌕ Search

SEARCH · Search NASA

Results for “wings”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1937

Free-spinning Wind-tunnel Tests of a Low-wing Monoplane with Systemic Changes in Wings and Tails

A series of tests was made at the National Advisory Committee for Aeronautics (NACA) free-spinning tunnel to determine the effect of systematic changes in wing and tail arrangement upon steady-spinning and recovery characteristics of a conventional low-wing monoplane model for a basic loading condition. Eight wings and three tails, covering a wide range of aerodynamic characteristics, were independently ballasted so as to be interchangeable with no change in mass distribution. For each of the 24 wing-tail combinations, observations were made of steady spins for four control settings and of recoveries for five control manipulators. The results are presented in the form of charts comparing the spin characteristics. The results showed that, with a poor tail arrangement, wing plan form and tip shape had a considerable effect on the spinning characteristics.

Seidman, Oscar↗
NASA NTRS1935

Tests of Nacelle-Propeller Combinations in Various Positions with Reference to Wings VI : Wings and Nacelles with Pusher Propeller

This report is the sixth of a series giving wind tunnel tests results on the interference drag and propulsive efficiency of nacelle-propeller-wing combinations. The present report gives the results of tests of a radial-engine nacelle with pusher propeller in 17 positions with reference to a Clark Y wing; tests of the same nacelle and propeller in three positions with reference to a thick wing; and tests of a body and pusher propeller with the thick wing, simulating the case of a propeller driven by an extension shaft from an engine within the wing. Some preliminary tests were made on pusher nacelles alone.

Wood, Donald H↗
NASA NTRS1936

The Influence of Wing Setting on the Wing Load and Rotor Speed of a PCA-2 Autogiro as Determined in Flight

Flight tests were made on PCA-2 autogiro with wing settings of 2.2 degrees, 0.9 degrees, and -0.5 degrees. The wing load and rotor speed were measured in steady glides. The results obtained show that a wide variation in rotor speed as a function of air speed can be obtained by a suitable adjustment of the wing setting; that by decreasing the wing setting the upper safe flying speed, determined by the decrease is rotor speed, is greatly increased; and that the interference of the wing on the rotor thrust and lift coefficients is negligible.

Wheatley, John B↗
NASA NTRS1941

Observations of the Effect of Wing Appendages and Flaps on the Spread of Separation of Flow over the Wing

The spread of the separation of flow on three tapered wings insymmetrical and unsymmetrical flow was observed with silk tufts. By equal thickness and chord distribution the wings manifested a different form of lifting line. The principal result of the study was that the wings alone first disclosed complete breakdown of the flow at the tips, even the one with twist, but that after adding fuselage and engine nacelles, the twisted wing broke down completely first in the wing center. The observed boundary layer motions transverse to the main flow direction were briefly explored as to their possible influence on the spread of the separation. On top of that certain disclosures were afforded in which the transverse motions observed in the boundary layer became perceptible even above the boundary layer.

Hartwig, G↗
NASA NTRS1994

Effect of leading- and trailing-edge flaps on clipped delta wings with and without wing camber at supersonic speeds

An experimental investigation of the aerodynamic characteristics of thin, moderately swept fighter wings has been conducted to evaluate the effect of camber and twist on the effectiveness of leading- and trailing-edge flaps at supersonic speeds in the Langley Unitary Plan Wind Tunnel. The study geometry consisted of a generic fuselage with camber typical of advanced fighter designs without inlets, canopy, or vertical tail. The model was tested with two wing configurations an uncambered (flat) wing and a cambered and twisted wing. Each wing had an identical clipped delta planform with an inboard leading edge swept back 65 deg and an outboard leading edge swept back 50 deg. The trailing edge was swept forward 25 deg. The leading-edge flaps were deflected 4 deg to 15 deg, and the trailing-edge flaps were deflected from -30 deg to 10 deg. Longitudinal force and moment data were obtained at Mach numbers of 1.60, 1.80, 2.00, and 2.16 for an angle-of-attack range 4 deg to 20 deg at a Reynolds number of 2.16 x 10(exp 6) per foot and for an angle-of-attack range 4 deg to 20 deg at a Reynolds number of 2.0 x 10(exp 6) per foot. Vapor screen, tuft, and oil flow visualization data are also included.

Hernandez, Gloria↗
NASA NTRS1958

Aerodynamic Characteristics in Sideslip of a Large-Scale 49 deg Sweptback Wing-Body-Tail Configuration with Blowing Applied Over the Flaps and Wing Leading Edge

An investigation has been conducted in the Langley full-scale tunnel to determine the aerodynamic characteristics in sideslip of a large-scale 490 sweptback wing-body-tail configuration having wing leading- edge and flap-blowing boundary-layer control. The wing and tails had an aspect ratio of 3.5, a taper ratio of 0.3, and NACA 65AO06 airfoil sections parallel to the plane of symmetry. The tests were conducted over a range of angles of attack of about -5 deg to 28 deg for sideslip angles of 0 deg, -5.06 deg, -10.15 deg, and -15.18 deg. Lateral and longitudinal stability and control characteristics were obtained for6a minimized blowing rate. The Reynolds number of the tests was 5.2 x 10(exp 6), corresponding to a Mach number of 0.08. The results of the investigation showed that sideslip to angles of about -15 deg did not require, from a consideration of the longitudinal characteristics, blowing rates over the wing leading edge or flap greater than that established as minimum at zero sideslip. The optimum configuration was laterally and directionally stable through the complete lift-coefficient range including the stall; however, maximum lift for sideslip angles greater than about 50 was seriously limited by a deficiency of lateral control. Blowing over the leading edge of the retreating wing in sideslip at a rate greater than that established as minimum at zero sideslip was ineffective in improving the lateral control characteristics. The optimum configuration at zero sideslip had no hysteresis of the aerodynamic parameters upon recovery from stall.

McLemore, H. Clyde↗
NASA NTRS1959

Subsonic Wing Loadings on a 45 deg Sweptback Wing and Body Combination at High Angles of Attack

A study has been made of the subsonic pressure distributions and loadings for a 45 deg sweptback-wing and body combination at angles of attack up to 36 deg. The wing had an aspect ratio of 5.5, a taper ratio of 0.53, and NACA 64A010 sections normal to the quarter-chord line and was mounted on a slender body of fineness ratio 12.5. Test results are presented for Mach numbers of 0.30 and 0.50 with corresponding Reynolds numbers of 1.5 and 2.0 million, respectively. The stall patterns and spanwise loadings at high angles of attack for the present model are correlated with those for other 45 deg sweptback wing and body combinations having aspect ratios between 4.0 and 8.0. A tentative approach is presented for extrapolating the Weissinger span-loading method to higher angles of attack, and for deriving the spanwise-load distributions for 45 deg sweptback wings at angles of attack above 20 deg. The investigation also included tests of the body in combination with only one panel of the swept wing. The problem of estimating the normal-force coefficient for the single panel at high angles of attack is considered.

Axelson, John A↗
NASA NTRS1992

Wing Download Results from a Test of a 0.658-Scale V-22 Rotor and Wing

A test of a 0.658-scale V-22 rotor and wing was conducted in the 40 x 80 Foot Wind Tunnel at Ames Research Center. One of the principal objectives of the test was to measure the wing download in hover for a variety of test configurations. The wing download and surface pressures were measured for a wide range of thrust coefficients, with five different flap angles, two nacelle angles, and both directions or rotor rotation. This paper presents these results, and describes a new method for interpreting wing surface pressure data in hover. This method shows that the wing flap can produce substantial lift loads in hover.

Felker, Fort F.↗
NASA NTRS2002

Wing Torsional Stiffness Tests of the Active Aeroelastic Wing F/A-18 Airplane

The left wing of the Active Aeroelastic Wing (AAW) F/A-18 airplane has been ground-load-tested to quantify its torsional stiffness. The test has been performed at the NASA Dryden Flight Research Center in November 1996, and again in April 2001 after a wing skin modification was performed. The primary objectives of these tests were to characterize the wing behavior before the first flight, and provide a before-and-after measurement of the torsional stiffness. Two streamwise load couples have been applied. The wing skin modification is shown to have more torsional flexibility than the original configuration has. Additionally, structural hysteresis is shown to be reduced by the skin modification. Data comparisons show good repeatability between the tests.

Lokos, William A.↗
NASA NTRS1956

Effect of Wing Height and Dihedral on the Lateral Stability Characteristics at Low Lift of a 45 Deg Swept-Wing Airplane Configuration as Obtained from Time-Vector Analyses of Rocket-Propelled-Model Flights at Mach Numbers from 0.7 to 1.3

Lateral-stability flight tests were made over the Mach number range from 0.7 to 1.3 of models of three airplane configurations having 45deg sweptback wings. One model had a high wing; one, a low wing; and one, a high wing with cathedral. The models were otherwise identical. The lateral oscillations of the models resulting from intermittent yawing disturbances were interpreted in terms of full-scale airplane flying qualities and were further analyzed by the time-vector method to obtain values of the lateral stability derivatives. The effects of changes i n wing height on the static sideslip derivatives were fairly constant in the speed range investigated and agreed well with estimated values based on subsonic wind-tunnel tests. Effects of geometric dihedral on the rolling moment due to sideslip agreed well with theoretical and other experimental results and with a theoretical relation involving the damping in roll. The damping in roll, when compared with theoretical and other experimental results, shared good agreement at supersonic speeds but was somewhat higher at a Mach number of 1.0 and at subsonic speeds. The damping in yaw shared no large changes in the transonic region.

Gillis, Clarence L.↗
NASA NTRS1935

Calculations of the Effect of Wing Twist on the Air Forces Acting on a Monoplane Wing

A method is presented for calculating the aerodynamic forces on a moncylane wing, taking into account the elastic twisting of the wing due to these forces. The lift distribution along the span is calculated by the formulas of Amstutz as a function of the geometrical characteristics of the wing and of the twist at stations 60 and 90 percent of the semispan. The twist for a given lift distribution is calculated by means of influence lines. As a numerical example, the forces on a Swiss military D.2V airplane are calculated. Comparisons with the strip method and with the ordinary stress-analysis method are also given.

FORMULAS-LIFT DISTRIBUTION-AMSTUTZ↗
NASA NTRS1929

Cantilever Wings for Modern Aircraft: Some Aspects of Cantilever Wing Construction with Special Reference to Weight and Torsional Stiffness

In the foregoing remarks I have made an attempt to touch on some of the structural problems met with in cantilever wings, and dealt rather fully with a certain type of single-spar construction. The experimental test wing was a first attempt to demonstrate the principles of this departure from orthodox methods. The result was a wing both torsionally stiff and of light weight - lighter than a corresponding biplane construction.

WINGS - STRUCTURE↗
NASA NTRS1948

Tests of a Triangular Wing of Aspect Ratio 2 in the Ames 12-foot Pressure Wind Tunnel III : the Effectiveness and Hinge Moments of a Skewed Wing-tip Flap

Results of wind-tunnel tests of a semispan model of a triangular wing of aspect ratio 2 with a skewed wing-tip flap are presented. Lift, drag, pitching-moment, and hinge-moment data are included for subsonic Mach numbers up to 0.95. The flap showed extremely high hinge moments and low effectiveness as a longitudinal control. Although less affected by compressibility, this flap is indicated to be inferior to a constant-chord flap when applied to this triangular wing.

MACH NUMBER EFFECTS - COMPLETE WINGS↗
NASA NTRS1972

Fan and wing force data from wind tunnel investigation of a 0.38 meter (15 inch) diameter VTOL model lift fan installed in a two dimensional wing

Test data are presented for a 38-cm (15-in.) diameter, 1.28 pressure ratio model VTOL lift fan installed in a two-dimensional wing and tested in a 2.74-by 4.58-meter (9-by 15-ft)V/STOL wind tunnel. Tests were run with and without exit louvers over a wide range of crossflow velocities and wing angle of attack. Tests were also performed with annular-inlet vanes, inlet bell-mouth surface disconuities, and fences to induce fan windmilling. Data are presented on the axial force of the fan assembly and overall wing forces and moments as measured on force balances for various static and crossflow test conditions. Midspan wing surface pressure coefficient data are also given.

Yuska, J. A.↗
NASA NTRS1973

A study of the effects of aeroelastic divergence on the wing structure of an oblique-wing supersonic transport configuration

The aerodynamic characteristics of transport aircraft with oblique wing flying at supersonic speeds are discussed. Aeroelastic divergence of the forward swept portion of the wing is analyzed. The effect of aspect ratio as a method for avoiding aeroelastic divergence is examined. A relatively low aspect ratio appears necessary for an oblique wing when constructed of conventional aluminum alloy materials. The aspect ratio may be increased by increasing the wing thickness ratio and by utilizing materials with higher moduli of elasticity and rigidity.

Source record↗
NASA NTRS1972

EBF noise tests with engine under-the-wing and over-the-wing configurations

Noise tests of externally blown flaps with the engine under the wing and engine over the wing configurations were conducted. Flap noise data obtained on a TF-34 aircraft are discussed. Noise data obtained during a free-jet forward-speed-effect analysis are presented. Noise sources associated with upper surface flap blowing are described. Results of a small scale configuration screening study and some large scale model test data are analyzed. The noise data for the engine over wing configurations are compared with the engine under the wing configurations.

Dorsch, R. G.↗
NASA NTRS1975

Effects of wing bend on the aerodynamic characteristics of a low aspect ratio oblique wing

Static longitudinal and lateral/directional force and moment results are presented for an elliptical oblique wing (aspect ratio 6) mounted on top of a body of revolution. The wing was tested at various sweep angles ranging from 0 to 60 deg throughout a Mach-number range of 0.6 to 1.4. Increasing the upward bend along the wing span resulted in no significant improvement in the linearity of the moment curves, but required an impractical wing pivot location to eliminate the rolling moments at low lift. Linear theory gave satisfactory predictions of the lift and moment-curve slopes at low lift.

Hopkins, E. J.↗