Search NASA⌕ Search

SEARCH · Search NASA

Results for “Curved Structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80

The dark matter density in the solar neighborhood reconsidered

The peculiar dip in the outer rotation curve at a distance of 9 kpc, which was recently confirmed by precise measurements with the VERA VLBI array in Japan, suggests donut-like substructures in the dark matter (DM) halo, since spherical or elliptical distributions will not cause a dip. Additionally, such a donut-like DM structure seems to be required by the dip in the gas flaring of the disk. In this paper we consider the impact of such DM substructure in the disk on the rotation curve, the gas flaring, the local DM density and the local surface density. A global fit shows that the rotation curve is best described by an NFW DM profile complemented by two donut-like DM substructures at radii of 4.2 and 12.4 kpc, which coincide with the local dust ring and the Monocerus ring of stars, respectively. Both regions have been suggested as regions with tidal streams from ''shredded'' satellites, thus enhancing the plausibility for additional DM. If real, the radial extensions of these nearby ringlike structures enhance the local dark matter density by a factor of four to about 1.3±0.3 GeV/cm{sup 3}. We find that i) this higher DM density is perfectly consistent with the local gravitational potential determining the surface density and ii) the s-shaped gas flaring is explained. Such a possible enhancement of the local DM density is of great interest for direct DM searches and the ringlike structure would change the directional dependence of gamma rays for indirect DM searches.

79 ASTRONOMY AND ASTROPHYSICS↗

Quantitative assessment of sample stiffness and sliding friction from force curves in atomic force microscopy

It has long been recognized that the angular deflection of an atomic force microscope (AFM) cantilever under ''normal'' loading conditions can be profoundly influenced by the friction between the tip and the surface. It is shown here that a remarkably quantifiable hysteresis occurs in the slope of loading curves whenever the normal flexural stiffness of the AFM cantilever is greater than that of the sample. This situation arises naturally in cantilever-on-cantilever calibration, but also when trying to measure the stiffness of nanomechanical devices or test structures, or when probing any type of surface or structure that is much more compliant along the surface normal than in transverse directions. Expressions and techniques for evaluating the coefficient of sliding friction between the cantilever tip and sample from normal force curves, as well as relations for determining the stiffness of a mechanically compliant specimen are presented. The model is experimentally supported by the results of cantilever-on-cantilever spring constant calibrations. The cantilever spring constants determined here agree with the values determined using the NIST electrostatic force balance within the limits of the largest uncertainty component, which had a relative value of less than 2.5%. This points the way for quantitative testing of micromechanical and nanomechanical components, more accurate calibration of AFM force, and provides nanotribologists access to information about contact friction from normal force curves.

36 MATERIALS SCIENCE↗

Thermoluminescence and glow curves analysis of γ-exposed Eu{sup 3+} doped K{sub 3}Y(PO{sub 4}){sub 2} nanophosphors

Highlights: • First time, a detailed comparative study of the glow curves and kinetic parameters was made on K{sub 3}Y(PO{sub 4}){sub 2} nanophosphor. • Combustion method was employed to synthesize the Eu{sup 3+} doped K{sub 3}Y(PO{sub 4}){sub 2} nanophosphor. • The nanophosphor exhibited sublinear response suggesting that it is suitable for TL dosimetry. - Abstract: Eu{sup 3+} doped K{sub 3}Y(PO{sub 4}){sub 2} nanophosphor was synthesized by combustion synthesis using urea as a fuel. The crystal structure and particle morphology of the nanophosphor were investigated by using X-ray diffraction and transmission electron microscopy, respectively. A Thermoluminescence (TL) study was carried out after exposing the samples to gamma radiation. The TL glow curves exhibited a prominent peak at 407 K and a small hump at 478 K. The intensity of the peaks increased with the increase in the dose of the gamma rays (0.01–5 kGy). The K{sub 3}Y(PO{sub 4}){sub 2}: Eu{sup 3+} (2.5 mol%) nanophosphor exhibited sublinear TL response to γ-radiation over a wide range of gamma doses (0.01–5 kGy). The TLanal program was used to analyze the glow curves of the K{sub 3}Y(PO{sub 4}){sub 2} nanophosphor at different doses (0.2–5 kGy) and different heating rates (3–10 K/s). A comparative study was done for kinetic trapping parameters that were determined by the peak shape methods of Chen, Grossweiner and Lushchik. The frequency factors (s) for each glow peak were also calculated. The values of the activation energy (E) obtained by the TLanal program were in good agreement with those obtained by the peak shape methods. The effect of different amount of doses and different heating rates are discussed.

36 MATERIALS SCIENCE↗

POD of ultrasonic detection of synthetic hard alpha inclusions in titanium aircraft engine forgings

The probability of detection (POD) of inspection techniques is a key input to estimating the lives of structural components such as aircraft engines. This paper describes work conducted as a part of the development of POD curves for the ultrasonic detection of synthetic hard alpha (SHA) inclusions in titanium aircraft engine forgings. The sample upon which the POD curves are to be based contains four types of right circular SHAs that have been embedded in a representative titanium forging, as well as a number of flat bottomed holes (FBHs). The SHAs were of two sizes, number 3 and number 5, with each size including seeds with nominal nitrogen concentrations of both 3 and 17 wt. %. The FBHs included sizes of number 1, number 3, and number 5. This discreteness of the data poses a number of challenges to standard processes for determining POD. For example, at each concentration of nitrogen, there are only two sizes, with 10 inspection opportunities each. Fully empirical, standard methodologies such as a circumflex versus a provide less than an ideal framework for such an analysis. For example, there is no way to describe the beam limiting effect whereby the signal no longer increases the flaw grows larger than the beam, one can only determine POD at the two concentration levels present in the block, and confidence bounds tend to be broad because of the limited data available for each case. In this paper, we will describe strategies involving the use of physics-based models to overcome these difficulties by allowing the data from all reflectors to be analyzed by a single statistical model. Included will be a discussion of the development of the physics-based model, its comparison to the experimental data (obtained at multiple sites with multiple operators) and its implications regarding the statistical analysis, whose details will be given in a separate article by Li et al. in this volume.

36 MATERIALS SCIENCE↗

Five micron limb-darkening and the structure of the Jovian atmosphere

A combined radiative, dynamical, and chemical model of the Jovian atmosphere is presented which reproduces the observed IR limb-darkening curves for several regions on the disk of Jupiter. Two approaches are used to perform the inversion required for determination of the source function, and a power-series-expansion model is examined, along with a convective-equilibrium model, cloud and intermediate-zone models, and a thin-shell model. The statistical methods used in the analysis are outlined, and model fits to the observations are discussed. The chemistry of phase transitions in the hot spots of Jupiter's equatorial belt is briefly investigated.

Newman, W. I.↗

Evolution of three-dimensionality in stable and unstable curved mixing layers

Results are presented of an experimental study tracing the effects of mild streamwise curvature (delta/R is less than 5 percent) on the 3D structure of a two-stream mixing layer at high Reynolds number (about 27,000). Measurements of the mean and fluctuating velocities were obtained on fine cross-plane grids at 11 streamwise locations using a rotatable cross-wide probe. Well-organized streamwise vorticity was generated in both cases through the braid instability. Although the vortex structures decayed with streamwise distance in both cases, the rate of decay for the unstable case was lower. As a result, the unstable layer exhibited noticeable spanwise variations in the mean velocity and Reynolds stresses. Both cases achieved linear growth, but the rate of growth for the unstable case was higher. The far-field spanwise-averaged peak Reynolds stresses were significantly higher for the destabilized case compared to the stabilized case, which exhibited levels comparable to those of a straight case.

Plesniak, Michael W.↗

THE GREEN BANK TELESCOPE H II REGION DISCOVERY SURVEY. III. KINEMATIC DISTANCES

Using the H I emission/absorption method, we resolve the kinematic distance ambiguity and derive distances for 149 of 182 (82%) H II regions discovered by the Green Bank Telescope H II Region Discovery Survey (GBT HRDS). The HRDS is an X-band (9 GHz, 3 cm) GBT survey of 448 previously unknown H II regions in radio recombination line and radio continuum emission. Here, we focus on HRDS sources from 67 Degree-Sign {>=} l {>=} 18 Degree-Sign , where kinematic distances are more reliable. The 25 HRDS sources in this zone that have negative recombination line velocities are unambiguously beyond the orbit of the Sun, up to 20 kpc distant. They are the most distant H II regions yet discovered. We find that 61% of HRDS sources are located at the far distance, 31% at the tangent-point distance, and only 7% at the near distance. 'Bubble' H II regions are not preferentially located at the near distance (as was assumed previously) but average 10 kpc from the Sun. The HRDS nebulae, when combined with a large sample of H II regions with previously known distances, show evidence of spiral structure in two circular arc segments of mean Galactocentric radii of 4.25 and 6.0 kpc. We perform a thorough uncertainty analysis to analyze the effect of using different rotation curves, streaming motions, and a change to the solar circular rotation speed. The median distance uncertainty for our sample of H II regions is only 0.5 kpc, or 5%. This is significantly less than the median difference between the near and far kinematic distances, 6 kpc. The basic Galactic structure results are unchanged after considering these sources of uncertainty.

79 ASTRONOMY AND ASTROPHYSICS↗

Grain Refinement by Authigenic Inoculation Inherited from the Medium-Range Order Structure of Ni-Cr-W Superalloy

The combination of liquidus casting and thermal control solidification furnace was applied to obtain a fine-grained ingot. A rapid quenching method and x-ray diffraction measurement were used to investigate the effect of authigenic inoculation on grain refinement. The structure factor S(Q) of liquid Ni-Cr-W superalloy at 1400 °C (Liquidus temperature) and bright-field image of the microstructures quenched from 1400 °C have been measured by the high-temperature x-ray diffractometer and the transmission electron microscopy (TEM), respectively. The results show that a pre-peak exists on a S(Q) curve at the liquidus temperature. The clusters of atom in rapidly quenched microstructures obtained by isothermal heat treatment at 1400 °C were studied using TEM. Meanwhile, the effect of isothermal different temperatures on rapidly quenched microstructures was studied. The results also show that there are only the globular, equiaxed grains distributed in the solidification structure. These particles are inherited from the medium-range order structure, which is beneficial for grain refinement. The normalized work-hardening rate-strain curve indicates the work-hardening rate of fine grain is higher than that of conventional grain at the same temperature and the same deformation.

36 MATERIALS SCIENCE↗

Aeroelastic Analysis of a Flexible Wing Wind Tunnel Model with Variable Camber Continuous Trailing Edge Flap Design

This paper presents data analysis of a flexible wing wind tunnel model with a variable camber continuous trailing edge flap (VCCTEF) design for drag minimization tested at the University of Washington Aeronautical Laboratory (UWAL). The wind tunnel test was designed to explore the relative merit of the VCCTEF concept for improved cruise efficiency through the use of low-cost aeroelastic model test techniques. The flexible wing model is a 10%-scale model of a typical transport wing and is constructed of woven fabric composites and foam core. The wing structural stiffness in bending is tailored to be half of the stiffness of a Boeing 757-era transport wing while the torsional stiffness is about the same. This stiffness reduction results in a wing tip deflection of about 10% of the wing semi-span. The VCCTEF is a multi-segment flap design having three chordwise camber segments and five spanwise flap sections for a total of 15 individual flap elements. The three chordwise camber segments can be positioned appropriately to create a desired trailing edge camber. Elastomeric material is used to cover the gaps in between the spanwise flap sections, thereby creating a continuous trailing edge. Wind tunnel data analysis conducted previously shows that the VCCTEF can achieve a drag reduction of up to 6.31% and an improvement in the lift-to-drag ratio (L=D) of up to 4.85%. A method for estimating the bending and torsional stiffnesses of the flexible wingUWAL wind tunnel model from static load test data is presented. The resulting estimation indicates that the stiffness of the flexible wing is significantly stiffer in torsion than in bending by as much as 9 to 1. The lift prediction for the flexible wing is computed by a coupled aerodynamic-structural model. The coupled model is developed by coupling a conceptual aerodynamic tool Vorlax with a finite-element model of the flexible wing via an automated geometry deformation tool. Based on the comparison of the lift curve slope, the lift prediction for the rigid wing is in good agreement with the estimated lift coefficients derived from the wind tunnel test data. Due to the movement of the VCCTEF during the wind tunnel test, uncertainty in the lift prediction due to the indicated variations of the VCCTEF deflection is studied. The results show a significant spread in the lift prediction which contradicts the consistency in the aerodynamic measurements, thus suggesting that the indicated variations as measured by the VICON system may not be reliable. The lift prediction of the flexible wing agrees very well with the measured lift curve for the baseline configuration. The computed bending deflection and wash-out twist of the flexible wing also match reasonably well with the aeroelastic deflection measurements. The results demonstrate the validity of the aerodynamic-structural tool for use to analyze aerodynamic performance of flexible wings.

Wind Tunnel↗

DIAGNOSING THE PROMINENCE-CAVITY CONNECTION

Prominences and cavities are ubiquitously observed together, but the physical link between these disparate structures has not been established. We address this issue by using dynamic emission in the extreme ultraviolet to probe the connections of these structures. The SDO/AIA observations show that the cavity exhibits excessive emission variability compared to the surrounding quiet-Sun streamer, particularly in the 171 A bandpass. We find that this dynamic emission takes the form of coherent loop-like brightening structures which emanate from the prominence into the central cavity. The geometry of these structures, dubbed prominence horns, generally mimics the curvature of the cavity boundary. We use a space-time statistical analysis of two cavities in multiple AIA bandpasses to constrain the energetic properties of 45 horns. In general, we find there is a positive correlation between the light curves of the horns in the 171 A and 193 A bandpasses; however, the 193 A emission is a factor of five weaker. There is also a strong correlation between structural changes to the prominence as viewed in the He II 304 A bandpass and the enhanced 171 A emission. In that bandpass, the prominence appears to extend several megameters along the 171 A horn where we observe co-spatial, co-temporal 304 A and 171 A emission dynamics. We present these observations as evidence of the magnetic and energetic connection between the prominence and the cavity. Further modeling work is necessary to explain the physical source and consequences of these events, particularly in the context of the traditional paradigm: the cavity is underdense because it supplies mass to the overdense prominence.

79 ASTRONOMY AND ASTROPHYSICS↗

Combining Droop Curve Concepts with Control Systems for Wind Turbine Active Power Control: Preprint

Wind energy is becoming a larger portion of the global energy portfolio and wind penetration has increased dramatically in certain regions of the world. This increasing wind penetration has driven the need for wind turbines to provide active power control (APC) services to the local utility grid, as wind turbines do not intrinsically provide frequency regulation services that are common withtraditional generators. It is common for large scale wind turbines to be decoupled from the utility grid via power electronics, which allows the turbine to synthesize APC commands via control of the generator torque and blade pitch commands. Consequently, the APC services provided by a wind turbine can be more flexible than those provided by conventional generators. This paper focuses on thedevelopment and implementation of both static and dynamic droop curves to measure grid frequency and output delta power reference signals to a novel power set point tracking control system. The combined droop curve and power tracking controller is simulated and comparisons are made between simulations using various droop curve parameters and stochastic wind conditions. The tradeoffs involvedwith aggressive response to frequency events are analyzed. At the turbine level, simulations are performed to analyze induced structural loads. At the grid level, simulations test a wind plant's response to a dip in grid frequency.

17 WIND ENERGY↗

Unsteady Aerodynamic Force Sensing from Measured Strain

A simple approach for computing unsteady aerodynamic forces from simulated measured strain data is proposed in this study. First, the deflection and slope of the structure are computed from the unsteady strain using the two-step approach. Velocities and accelerations of the structure are computed using the autoregressive moving average model, on-line parameter estimator, low-pass filter, and a least-squares curve fitting method together with analytical derivatives with respect to time. Finally, aerodynamic forces over the wing are computed using modal aerodynamic influence coefficient matrices, a rational function approximation, and a time-marching algorithm. A cantilevered rectangular wing built and tested at the NASA Langley Research Center (Hampton, Virginia, USA) in 1959 is used to validate the simple approach. Unsteady aerodynamic forces as well as wing deflections, velocities, accelerations, and strains are computed using the CFL3D computational fluid dynamics (CFD) code and an MSC/NASTRAN code (MSC Software Corporation, Newport Beach, California, USA), and these CFL3D-based results are assumed as measured quantities. Based on the measured strains, wing deflections, velocities, accelerations, and aerodynamic forces are computed using the proposed approach. These computed deflections, velocities, accelerations, and unsteady aerodynamic forces are compared with the CFL3D/NASTRAN-based results. In general, computed aerodynamic forces based on the lifting surface theory in subsonic speeds are in good agreement with the target aerodynamic forces generated using CFL3D code with the Euler equation. Excellent aeroelastic responses are obtained even with unsteady strain data under the signal to noise ratio of -9.8dB. The deflections, velocities, and accelerations at each sensor location are independent of structural and aerodynamic models. Therefore, the distributed strain data together with the current proposed approaches can be used as distributed deflection, velocity, and acceleration sensors. This research demonstrates the feasibility of obtaining induced drag and lift forces through the use of distributed sensor technology with measured strain data. An active induced drag control system thus can be designed using the two computed aerodynamic forces, induced drag and lift, to improve the fuel efficiency of an aircraft. Interpolation elements between structural finite element grids and the CFD grids and centroids are successfully incorporated with the unsteady aeroelastic computation scheme. The most critical technology for the success of the proposed approach is the robust on-line parameter estimator, since the least-squares curve fitting method depends heavily on aeroelastic system frequencies and damping factors.

shape sensing↗

Systematics of the Third Row Transition Metal Melting: The HCP Metals Rhenium and Osmium

The melting curves of rhenium and osmium to megabar pressures are obtained from an extensive suite of ab initio quantum molecular dynamics (QMD) simulations using the Z method. In addition, for Re, we combine QMD simulations with total free energy calculations to obtain its phase diagram. Our results indicate that Re, which generally assumes a hexagonal close-packed (hcp) structure, melts from a face-centered cubic (fcc) structure in the pressure range 20–240 GPa. We conclude that the recent DAC data on Re to 50 GPa in fact encompass both the true melting curve and the low-slope hcp-fcc phase boundary above a triple point at (20 GPa, 4240 K). A linear fit to the Re diamond anvil cell (DAC) data then results in a slope that is 2.3 times smaller than that of the actual melting curve. The phase diagram of Re is topologically equivalent to that of Pt calculated by us earlier on. Regularities in the melting curves of Re, Os, and five other 3rd-row transition metals (Ta, W, Ir, Pt, Au) form the 3rd-row transition metal melting systematics. We demonstrate how this systematics can be used to estimate the currently unknown melting curve of the eighth 3rd-row transition metal Hf.

36 MATERIALS SCIENCE↗

Comparison of Three Methods for Calculating the Compressive Strength of Flat and Slightly Curved Sheet and Stiffener Combinations

This report gives a comparison of the accuracy of the three methods for calculating the compressive strength of flat sheet and stiffener combinations such as occur in stressed-skin or monocoque structures for aircraft. Of the three methods based upon various assumptions with regard to the interaction of sheet and stiffener, the method based upon mutual action of the stiffener and an effective width as a column gave the best agreement with the results of the tests. An investigation of the effect of small curvature resulted in the conclusion that the compressive strength of the curved panels is, for all practical purposes, equal to the strength of flat panels except for thick sheet where non-uniform curvature throughout the length may cause the strength of the curved panel to be 10 to 15 percent less than that of a corresponding flat panel.

STRESSED SKIN↗

Application of Quasi-Static Modal Analysis to an Orion Multi-Purpose Crew Vehicle Test

Bolted structural joints often exhibit load-dependent stiffness and energy dissipation that leads to nonlinear, amplitude dependent frequency and damping in the structure. As an alternative to direct integration of the nonlinear equations of motion, quasi-static modal analysis (QSMA) determines the dependence of frequency and damping on response amplitude using loading behavior from nonlinear static analyses. QSMA has previously been demonstrated to substantially reduce computational cost and maintain accuracy relative to full nonlinear dynamic simulation. This work explores the applicability of QSMA to a complex, large-scale aerospace structure. QSMA is employed to analyze a nonlinear model of test hardware developed to support the Orion Multi-Purpose Crew Vehicle program, which exhibited nonlinear behavior during dynamic testing at flight-like load levels. In addition to the extraction of amplitude-dependent frequency and damping curves, a Bouc-Wen hysteresis model was used in conjunction with the quasi-static results to develop nonlinear, uncoupled, time-domain modal equations of motion for the structure. Excellent agreement was observed between the reduced and full-order nonlinear models, encouraging future employment of QSMA to support accurate and efficient model reduction of structures with bolted joint nonlinearities.

QSMA↗

Synthesis and magnetization studies of nanopowder Fe₇₀Ni₂₀Cr₁₀ alloys prepared by high energy milling

Nanocrystalline Fe{sub 1–x–y}Ni x Cr y (x=20, y=10% in Wt)) alloy samples were prepared by mechanical alloying process. Fe, Ni and Cr elemental powders have been ball milled in a planetary mill for various periods of time, up to 27 h. XRD analysis allowed the determination of the structure of the mixture, the average crystallite size and the lattice parameter as a function of milling time. The complete formation of FeNiCr is observed after 27 h milling. With increasing milling time from 0 to 27 h, it is observed that the lattice parameter increases from 0.3515 to 0.3593 nm as well as an increase of microstrain from 0.15 to 0.40%, whereas the grain size decreases from 48 to 13 nm. Grain morphology of the powders at different formation stages was examined using SEM. Saturation magnetization and coercive fields derived from the hysteresis curves are discussed as a function of milling time. - Graphical abstract: Fe₇₀Ni₂₀Cr₁₀ nanopowders were prepared using a planetary ball mill. The structure and microstructure vary with milling time; thereby important modifications of the magnetic properties were observed and discussed. Highlights: • Nanocrystalline Fe₇₀Ni₂₀Cr₁₀ alloy were prepared by the mechanical alloying process. • The complete formation of Fe₇₀Ni₂₀Cr₁₀ is observed after 24 h milling. • With increasing milling time, the grain size decreases, while the strain increases. • The SEM images allowed following the morphology of the materials at different stages. • M s and H C derived from the hysteresis are discussed as a function of milling time.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Progressive collapse analysis of stiffened panel structure with consideration of actual welding distortion and residual stresses

To date, inclusion of welding distortion and residual stresses in determining the strength of marine structures is based on empirical formulations due to welding complexity. In this study, a more feasible numerical model was developed from the perspective of inherent strain theory. The accuracy of this simplified numerical model was confirmed by transient thermo-elastic–plastic finite element analysis using a novel dynamic mesh refining and iterative substructure method which is 50 times faster than conventional finite element method. Welding distortion by the two numerical approaches was validated with experimental measurement. The collapse analyses indicated that the inherent strain model predicted a compressive strength and load-displacement curve with high accuracy, as validated by the transient thermo-mechanical model. The global stiffness and the ultimate strength of the welded structure would be overestimated by about 22% if no welding effects were considered. The proposed computation procedure for determining the ultimate strength of welded structures is accurate, simple, and practical and enables improvement of ultimate strength through optimization of welding joint design to reduce the welding residual stress and distortion.

Huang, Hui↗

Efficient Scalable Parallel Higher Order Direct MoM-SIE Method With Hierarchically Semiseparable Structures for 3-D Scattering

A novel fast scalable parallel algorithm is proposed for the solution of large 3-D scattering problems based on: 1) the double (geometrical and current-approximation) higher order (DHO) method of moments (MoM) in the surface integral equation (SIE) formulation and 2) a direct solver for dense linear systems utilizing hierarchically semiseparable (HSS) structures. Namely, an HSS matrix representation is used for compression, factorization, and solution of the system matrix. In addition, a rank-revealing QR decomposition for memory compression is used, with a stopping criterion in terms of the relative rank tolerance value. One method for geometrical preprocessing of the scatterers based on the cobblestone distance sorting technique is employed in order to enhance the HSS algorithm accuracy and parallelization. Numerical examples show how the accuracy of the DHO HSS-MoM-SIE method is easily controllable by using the relative tolerance for the matrix compression. Furthermore, the examples demonstrate low memory consumption, as well as much faster simulation time, when compared to the direct LU decomposition. The method enables dramatically faster monostatic scattering computations than iterative solvers and reduced number of unknowns when compared to low-order discretizations. Finally, great scalability of the algorithm is demonstrated on more than one thousand processes.

97 MATHEMATICS AND COMPUTING↗