Search NASA⌕ Search

SEARCH · Search NASA

Results for “Mobile Measuring System”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80

Physical property characteristics of gas hydrate-bearing reservoir and associated seal sediments collected during NGHP-02 in the Krishna-Godavari Basin, in the offshore of India

India’s National Gas Hydrate Program Expedition 02 (NGHP-02) was conducted to better understand geologic controls on gas hydrate occurrence and morphology, targeting coarse-grained sediments along the lower continental slope offshore eastern India. This study combines seismic, logging-while-drilling data, and a petroleum system approach to provide a regional geologic and lithologic context for: 1) gas hydrate morphology and distribution, and 2) effects of fine-grained sediments (clays and other grains smaller than 63µm) on gas production in NGHP-02 Area B in the Krishna-Godavari Basin. Area B seismic data show a buried anticline/syncline structure with strong reflectors, R1 and R2, that delineate two of the five lithologic units: Unit I (shallowest), II (R1), III, IV (R2) and V (below the bas of gas hydrate stability). Throughout Area B, gas hydrate morphology depends on its placement within these units. Specifically, core- and grain-scale measurements indicate fines content exerts a primary control on the gas hydrate distribution and morphology. Units I, II and III are generally fine-grained. On the anticline crest, these units host primarily grain-displacing gas hydrate veins linked to pore-occupying gas hydrate in thin, localized, coarser-grained deposits. Diatoms in Unit III increase porosity with depth, reaching ~70% where it contacts Unit IV, the gas hydrate reservoir associated with reflector R2. The Unit III lithology and porosity allow fluid and dissolved-phase methane to escape Unit IV and form gas hydrate in the fine-grained overburden. Within Unit IV, fine-grained layers are interbedded with coarser-grained gas hydrate reservoir sands, and the fines content even in the sands is high enough to impact hydraulic and mechanical properties during gas production. Fluid motion during gas production can mobilize fines, which can then clog pore throats, limiting production rates. In conclusion, pore-water freshening during gas hydrate dissociation can increase fines mobilization, particularly given the smectite identified in the fine-grained interbeds.

03 NATURAL GAS↗

Detecting fractionalization in critical spin liquids using color centers

Quantum spin liquids are highly entangled ground states of insulating spin systems, in which magnetic ordering is prevented down to the lowest temperatures due to quantum fluctuations. One of the most extraordinary characteristics of quantum spin liquid phases is their ability to support fractionalized, low-energy quasiparticles known as spinons, which carry spin-1/2 but bear no charge. Relaxometry based on color centers in crystalline materials—of which nitrogen-vacancy (NV) centers in diamond are a well-explored example—provides an exciting new platform to probe the spin spectral functions of magnetic materials with both energy and momentum resolution and to search for signatures of these elusive, fractionalized excitations. In this work, we theoretically investigate the color-center relaxometry of two archetypal quantum spin liquids: the two-dimensional U(1) quantum spin liquid with a spinon Fermi surface and the spin-1/2 antiferromagnetic spin chain. The former is characterized by a metallic, spin-split ground state of mobile, interacting spinons, which closely resembles a spin-polarized Fermi liquid ground state but with neutral quasiparticles. We show that the observation of the Stoner continuum and the collective spin wave mode in the spin spectral function would provide a strong evidence for the existence of spinons and fractionalization. In one dimension, mobile spinons form a Luttinger liquid ground state. We show that the spin spectral function exhibits strong features representing the collective density and spin-wave modes, which are broadened in an algebraic fashion with an exponent characterized by the Luttinger parameter. The possibilities of measuring these collective modes and detecting the power-law decay of the spectral weight using NV relaxometry are discussed. We also examine how the transition rates are modified by marginally irrelevant operators in the Heisenberg limit. Published by the American Physical Society 2024

Takei, So (ORCID:0000000191771895)↗

Study of carbonaceous nanoparticles in premixed C{sub 2}H{sub 4}-air flames and behind a spark ignition engine

Nanoparticle size distributions and their concentrations were studied in atmospheric premixed ethylene/air flames using photo ionization mass spectrometry (PIMS) and total organic carbon (TOC) calibration supplemented by differential mobility analysis (DMA). Focus of this study is the evolution of nanoparticles as a function of height above burner (HAB) and of the C/O ratio of the unburned gases. It was found that especially particles of the cluster type exhibit a sharp concentration drop by more than two orders of magnitude within a narrow C/O window which is close to the sooting threshold. Using DMA a decline by two orders of magnitude was found. These results suggest that at best only small concentrations of nanoparticles should be formed significantly below the sooting threshold. As these conditions prevail in a homogeneously charged IC engine no or only very small nanoparticle emissions are expected in the exhaust gas. This was indeed found for a small Otto engine driving a power generator unit. Using flame nanoparticle profiles as standard, absolute concentrations for their emissions could be deduced. These data were supported by additional DMA measurements. The calibration using TOC did not completely match the one based on the condensation particle counter of the DMA apparatus. (author)

33 ADVANCED PROPULSION SYSTEMS↗

Development and implementation of high-throughput proteomic and metabolomics assays by using advanced chromatographic and mass spectrometric systems (CRADA Final Report)

The mission of this CRADA with Agilent was to couple powerful MS platforms (QQQ, IM-QTOFMS) with Agilent’s novel Ultra-High-Performance Liquid Chromatography (UHPLC) fast metabolomic workflows and perform ABF Machine Learning (ML) to generated datasets. Agilent transferred UHPLC methods to PNNL and LBNL and methods were implemented and demonstrated in both labs, achieving total acquisition times of < 10 min. Metabolites analyzed using Agilent’s shared methods included metabolites from central carbon metabolism, common across hosts, and metabolites unique to engineered strains. Standards were acquired in an UHPLC-Drift Tube Ion Mobility Mass Spectrometer (DTIMS) system for the first time within the context of ABF and methods were optimized based on Agilent’s protocols. Samples from ABF hosts Pseudomonas putida, Aspergillus pseudoterreus, Aspergillus niger and Rhodosporidium toruloides were analyzed using the UHPLC-DTIMS platform for a total of 276 runs. A data analysis workflow compatible with the Experimental Data Depot (EDD) and completely shareable was developed for the acquired UHPLC-DTIMS data. Samples were analyzed using a Data Independent Acquisition Approach (DIA), which for most of the standards provided more transitions therefore increasing detection confidence. Using the data acquired by PNNL, LBNL, and Agilent’s specifications from previous ML projects, SNL applied an ensemble ML strategy to pick the best performing model for automated LC-method selection. Finally, with the contribution of the participant labs and Agilent, SNL developed an Automated Method Selection (AMS) software tool to predict the best liquid chromatography method for analysis of any new molecules of interest. Samples with novel pathways and new metabolite targets of interest are generated at a high pace in the ABF. Overall, the project advanced rapid metabolomics by combining liquid chromatography, ion mobility spectrometry, and data-independent mass spectrometry with machine learning. This multidimensional approach uses retention time, collision cross-section, precursor mass, and fragment-ion information to distinguish chemically similar metabolites that can be difficult to resolve using conventional liquid- or gas-chromatography methods. The resulting workflow also provided automated metabolite-identification error estimates, addressing a recognized need for statistical confidence measures in metabolomics.

Petzold, Christopher [Lawrence Berkeley National L↗

The solubility and speciation of REE phosphate endmembers (CePO 4 and YPO 4 ) in Cl-rich aqueous fluids from 350 to 450 °C and implications for natural systems

The rare earth elements (REE) are important metals used increasingly in advanced technologies. Within the crust, the elements Ce and Y are commonly more abundant compared to other lanthanides and comprise important end-member constituents of REE-bearing minerals. Specifically, Ce is part of the light (L) REE which have larger ionic radii than the heavy (H) REE, which are grouped together with Y. These differences in ionic radius can lead to important physico-chemical trends within the lanthanide group. Despite a recent increase in experimental and thermodynamic data for the REE at high temperature and pressure, there is still a significant lack of these data at supercritical conditions. In this study we conducted batch-type experiments to measure the solubility of REE phosphates (CePO 4 and YPO 4 ) at varying starting pH (1.5–10), and salinity (0.01–1.4 mol/kg NaCl) at 350 and P sat , and from 400 to 450 °C at 700 bar. Results show that the solubility of Ce (33–0.14 ppb) is generally higher than Y (13–0.13 ppb) and that Ce complexes more strongly with both chloride and hydroxyl ligands compared to Y. The solubilities of both REE phosphates are highly pH-dependent and, to a lesser extent, depend on salinity at the studied conditions. The solubility data from this study were implemented into the GEMSFITS program to optimize the thermodynamic properties of Ce and Y hydroxyl and chloride species. The updated standard partial molal Gibbs energies of formation (Δ f G 0 T,P ) are used within the experimental temperature and pressure range to accurately predict the CePO 4 and YPO 4 solubility and Ce and Y speciation behavior. Based on the updated thermodynamic properties we also provide formation constants (log β n Cl,OH ) for Ce and Y hydroxyl and chloride species. Updated thermodynamic properties are applied to model REE-apatite dissolution and REE mobility based on the Pea Ridge iron oxide apatite deposit in Missouri, USA. The apatite dissolution model replicates natural observations including the replacement of monazite and xenotime after apatite and is an example of the utility of the new thermodynamic constants applied to supercritical crustal fluids. Furthermore, the findings of this study advance the predictive capabilities of geochemical models, our understanding of the behavior of individual REE, and permit modeling the overarching fractionation trends between LREE and HREE in supercritical crustal fluids.

58 GEOSCIENCES↗

Variability in Ocean Color Associated with Phytoplankton and Terrigenous Matter: Time Series Measurements and Algorithm Development at the FRONT Site on the New England Continental Shelf

Fronts in the coastal ocean describe areas of strong horizontal gradients in both physical and biological properties associated with tidal mixing and freshwater estuarine output (e.g. Simpson, 1981 and O Donnell, 1993). Related gradients in optically important constituents mean that fronts can be observed from space as changes in ocean color as well as sea surface temperature (e.g., Dupouy et al., 1986). This research program is designed to determine which processes and optically important constituents must be considered to explain ocean color variations associated with coastal fronts on the New England continental shelf, in particular the National Ocean Partnership Program (NOPP) Front Resolving Observational Network with Telemetry (FRONT) site. This site is located at the mouth of Long Island sound and was selected after the analysis of 12 years of AVHRR data showed the region to be an area of strong frontal activity (Ullman and Cornillon, 1999). FRONT consists of a network of modem nodes that link bottom mounted Acoustic Doppler Current Profilers (ADCPs) and profiling arrays. At the center of the network is the Autonomous Vertically Profiling Plankton Observatory (AVPPO) (Thwaites et al. 1998). The AVPPO consists of buoyant sampling vehicle and a trawl-resistant bottom-mounted enclosure, which holds a winch, the vehicle (when not sampling), batteries, and controller. Three sampling systems are present on the vehicle, a video plankton recorder, a CTD with accessory sensors, and a suite of bio-optical sensors including Satlantic OCI-200 and OCR-200 spectral radiometers and a WetLabs ac-9 dual path absorption and attenuation meter. At preprogrammed times the vehicle is released, floats to the surface, and is then winched back into the enclosure with power and data connection maintained through the winch cable. Communication to shore is possible through a bottom cable and nearby surface telemetry buoy, equipped with a mobile modem, giving the capability for near-real time data transmission and interactive sampling control.

Morrison, John R.↗

Profiling at Oliktok Point to Enhance Year of Polar Prediction (YOPP) Experiments (POPEYE) Field Campaign Report

The arctic region is rapidly evolving, and enhanced predictive capabilities, for both weather and climate, are urgently required. Therefore, the international community is executing an extended period of focused observations and modeling of the arctic environment, dubbed the Year of Polar Prediction or YOPP. The YOPP featured two special observing periods (SOPs) (and will feature a third in 2020). The first of the completed SOPs occurred in the spring of 2018, and the second during the late summer and early fall of 2018. Here, we summarize the deployment of additional U.S. Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) user facility resources to the third ARM Mobile Facility (AMF3) at Oliktok Point, Alaska during the second three-month SOP (1 July 2018–30 September 2018). This deployment, named POPEYE (Profiling at Oliktok Point to Enhance YOPP Experiments), included the launching of extra radiosondes (one more per day) and operation of ARM-operated unmanned aircraft (DataHawk 2s) and ARM-operated tethered balloons. These instruments conducted routine profiling activities over the course of the special observing period to obtain measurements of atmospheric thermodynamic structure, cloud and precipitation properties, and aerosol properties. These measurements are expected to be used for a variety of purposes, including: 1) to conduct detailed studies of arctic cloud and aerosol processes; 2) to inform YOPP modeling efforts through real-time availability for assimilation into operational and research analysis products; 3) to evaluate and improve retrieval algorithms involving ARM remote sensors; 4) to evaluate and improve a variety of modeling tools being used to forecast arctic weather and climate; and 5) to initialize and evaluate simulations associated with a potential arctic large-eddy (LES) simulation framework similar to the ongoing LES ARM Symbiotic Simulation and Observation (LASSO) project.

Oliktok Point, Arctic processes, unmanned aerial v↗

Dissolved pyrogenic carbon leaching in soil: Effects of soil depth and pyrolysis temperature

We report Pyrogenic organic carbon (PyC) is found in soils as a heterogeneous mixture of thermally altered plant residues that range in their susceptibility to losses via mineralization, leaching, and erosion. Leaching of PyC as DOC (DPyC) within the soil profile is likely influenced by the chemical composition of solid PyC and the dominant soil processes and properties at a particular depth. Here we report the results of a 2-year laboratory decomposition and leaching study designed to investigate the interactive effects of pyrolysis temperature levels (no pyrolysis, 300 °C, and 450 °C) and soil depth (surface soil, 0–10 cm depth; subsurface soil, 50–70 cm depth) on losses of 13 C-labeled jack pine (Pinus banksiana) wood, wood pyrolyzed at 300 °C (PyC300) and wood pyrolyzed at 450 °C (PyC450) as dissolved organic carbon (DOC). Losses of wood and PyC in the 13 C- DOC pool were measured in leachates drained from soils once a month over the course of 1 year, and at one single leaching event after 2 years. We found that pyrolysis temperature levels interacted with time and soil depth to affect losses of wood and PyC as DOC throughout the 1-year incubation and leaching study, with greater DOC losses from wood in surface soil (0.73 ± 0.076% of added C) than in subsurface soil (0.40 ± 0.063% of added C) averaged across sampling time. Monthly DOC losses from PyC were not affected by soil depth. Cumulative data indicated a small contribution of wood (2.86 ± 0.07%), PyC300 (0.40 ± 0.04%), and PyC450 (0.16 ± 0.01%) to total DOC leached from soils. DOC losses from wood and PyC300 (as a proportion of added C) were greater in surface soil than in subsurface soil, whereas DOC losses from PyC450 were unaffected by differences between surface and subsurface soil. Losses of DOC were greater from PyC300 than from PyC450 in surface soil, with no significant differences in DOC losses between PyC300 and PyC450 in subsurface soil. One single leaching event at the end of the 2-year decomposition study resulted in higher DOC losses from wood in subsurface soil than in surface soil likely due to desorption, and no differences in DOC losses between PyC300 and PyC450 regardless of soil depth. Our results suggest strong interactions between the initial physicochemical composition of organic C inputs and soil properties (soil depth as a proxy) that control the mobility and transport of PyC and should be better represented in Earth system models.

54 ENVIRONMENTAL SCIENCES↗

Study of an unrefined humate solution as a possible remediation method for groundwater contamination - 15698

Savannah River Site (SRS) was one of the major nuclear processing facilities in the U.S. where plutonium was produced during the Cold War. Approximately 1.8 billion gallons of low level acidic waste solution containing radionuclides and dissolved metals were discharged to a series of unlined seepage basins at the F/H Area. Uranium is a key contaminant of concern in the basin's groundwater. It is migrating into the groundwater creating an acidic plume with a pH between 3-5.5. Groundwater Actions: The pump-and-treat water treatment unit was designed and built in 1997 to remove metals and radionuclides. In 2004 a hybrid funnel-and-gate system was constructed to create a treatment zone in which the acidic nature of the contaminated sediments could be reversed. Huma-K is an organic fertilizer that comes from the alkaline extraction of leonardite (a low-rank coal). Huma-K has a high content of humic substances which consist of complex organic compounds formed by the decomposition of plant and animal tissue. The objective of this study is to determine if a low cost unrefined humate solution (Huma-K) can be used to facilitate uranium adsorption to control its mobility in acidic groundwater. This study can assist in evaluating whether Huma-K can be used as an in situ amendment for the remediation of groundwater contaminated with uranium. Sediments from FAW-1 70-90 ft were used in this experiment. Sediments were disaggregated and sieved to a particle size of . 2 mm. Concentrations in the range 10-500 ppm were tested. Once all the components were added, pH was adjusted to 4. Samples were vortex mixed and placed on a shaker table at 100 RPM for a period of 24 hours in order to reach the adsorption equilibrium. Once the adsorption equilibrate was reached, samples were centrifuged at 2700 RPM to separate the liquid and the solid phase. The liquid fraction was analyzed using a Thermo Scientific Genesys 10S UV-Vis spectrophotometer. The same experimental design was used as explained above. A known concentration of Huma-K was used to study the pH effect on the sorption process. pH values were measured at the beginning and at the end of the experiment. Spectra of Huma-K show a featureless character. Absorbance of light increases as the wavelength is decreased. Measurements were done at 254 nm due to the presence of aromatic rings. Apparently there are two sorption processes. The first one follows the same trend as the Langmuir isotherm up to 250 ppm. The second sorption process occurs after all the binding sites in the sediments have been occupied. Precipitation decreases as the pH is increased. Based on the sorption isotherm, humic substances apparently bind first to the binding sites of the sediments particles. Once all the binding sites have been occupied, other sorption processes may start to dominate. Sorption is affected by pH. Higher sorption is seen at low pH values. Increased precipitation at low pH values is probably due to the neutralization of surface charges of humic molecules making them agglomerate.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Optical and electron transport properties of rock-salt Sc{sub 1−x}Al{sub x}N

Epitaxial single-crystal Sc{sub 1−x}Al{sub x}N ternary alloy layers deposited by magnetron co-sputtering on MgO(001) substrates at 950 °C exhibit a solid solution rock-salt phase for x = 0–0.2 without decomposition. Optical absorption indicates a linear increase in the optical gap from 2.51 eV for ScN to 3.05 eV for Sc{sub 0.8}Al{sub 0.2}N and, after correction due to the Moss-Burstein shift, a direct X point interband transition energy E{sub g}(X) = 2.15 + 2.75 x (eV). Correspondingly, the direct transition at the zone center increases with Al concentration according to E{sub g}(Γ) = 3.80 + 1.45 x (eV), as determined from a feature in the reflection spectra. All layers are degenerate n-type semiconductors with a room temperature mobility that decreases from 22 to 6.7 to 0.83 cm{sup 2}/V s as x increases from 0 to 0.11 to 0.20. The corresponding carrier densities are 9.2 × 10{sup 20}, 7.9 × 10{sup 20}, and 0.95 × 10{sup 20 }cm{sup −3} as determined from Hall measurements and consistent with optical free carrier absorption below photon energies of 1 eV. Temperature dependent transport measurements indicate metallic conduction for ScN, but weak localization that leads to a resistivity minimum at 85 and 210 K for x = 0.051 and 0.15, respectively, and a negative temperature coefficient over the entire measured 4–300 K range for Sc{sub 0.8}Al{sub 0.2}N. The decreasing mobility is attributed to alloy scattering at randomly distributed Al atoms on cation sites, which also cause the weak localization. The carrier density is primarily due to unintentional F doping from the Sc target and decreases strongly for x > 0.15, which is attributed to trapping in defect states due to the deterioration of the crystalline quality, as evidenced by the x-ray diffraction peak width that exhibits a minimum of 0.14° for x = 0.11 but increases to 0.49° for x = 0.20. This is consistent with asymmetric x-ray diffraction analyses, indicating a relaxed lattice constant that decreases from 4.511 ± 0.005 to 4.411 ± 0.004 Å for x = 0–0.2, and a biaxial in-plane compressive strain that decreases from −1.1% to −0.2% as x increases from 0 to 0.11, which is attributed to the higher Al adatom mobility, but increases again to −1.8% for x = 0.20, as x approaches the critical composition for phase separation, which causes structural instability and a higher defect density.

36 MATERIALS SCIENCE↗

Evaluation of Gas Chromatography/Mini-IMS to Detect VOCs

The Toxicology Laboratory at Johnson Space Center (JSC) has pioneered the use of gas chromatography-ion mobility spectrometry (GC/IMS) for measuring target volatile organic compounds (VOCs) aboard spacecraft. Graseby Dynamics, under contract to NASA/Wyle, has built several volatile organic analyzers (VOA) based on GC/IMS. Foremost among these have been the volatile organic analyzer-risk mitigation unit and the two flight VOA units for International Space Station (ISS). The development and evaluation of these instruments has been chronicled through presentations at the International Conference on Ion Mobility Spectrometry over the past three years. As the flight VOA from Graseby is prepared for operation on ISS at JSC, it is time to begin evaluations of technologies for the next generation VOA, Although the desired instrument characteristics for the next generation unit are the same as the current unit, the requirements are much more stringent. As NASA looks toward future missions beyond Earth environs, a premium will be placed upon small, light, reliable, autonomous hardware. It is with these visions in mind that the JSC Toxicology Laboratory began a search for the next generation VOA. One technology that is a candidate for the next generation VOA is GC/IMS. The recent miniaturization of IMS technology permits it to compete with other, inherently small, technologies such as chip-sized sensor arrays. This paper will discuss the lessons learned from the VOA experience and how that has shaped the design of a potential second generation VOA based upon GC/IMS technology. Data will be presented from preliminary evaluations of GC technology and the mini-IMS when exposed to VOCs likely to be detected aboard spacecraft. Results from the evaluation of an integrated GC/mini-IMS system will be shown if available.

Limero, Thomas↗

Triton Hopper: Exploring Neptune's Captured Kuiper Belt Object

Neptune's moon Triton is a fascinating object, a dynamic moon with an atmosphere, and geysers. Triton is unique in the outer solar system in that it is most likely a captured Kuiper belt object (KBO), a leftover building block of the solar system. When Voyager flew by it was the coldest body yet found in our solar system (33 degrees Kelvin) and had volcanic activity, geysers, and a thin atmosphere. It is covered in ices made from nitrogen, water, and carbon-dioxide, and shows surface deposits of tholins, organic compounds that may be precursor chemicals to the origin of life. Exploring Triton will be a challenge well beyond anything done in previous missions; but the unique environment of Triton also allows some new possibilities for mobility. We developed a conceptual design of a Triton Hopping probe that both analyzes the surface and collects it for use to propel its hops. The Hopper would land near the South Pole in 2040 where geysers have been detected. Depending the details of propulsion chosen the Hopper should be able to jump over 300 kilometers in 60 hops or less, exploring the surface and thin atmosphere on its way. This craft will autonomously carry out detailed scientific investigations on the surface, below the surface (drilling) and in the upper atmosphere to provide unprecedented knowledge of a KBO-turned moon and expanding NASA's existing capabilities in deep space planetary exploration to include Hoppers using different ices for propellant. Triton is roughly 2700 kilometers in diameter with a surface of mostly frozen nitrogen, mostly water ice crust and core of metal and rock. Its gravity is half that of Earth's Moon and its atmosphere is 170,000th of Earth's or 0.3 of Mars.The mission concept studied investigated the full surface and atmospheric phenomenon: chemical composition of surface and near subsurface materials, the thin atmosphere, volcanic and geyser activity. Measurements of all these aspects of Triton's unique environment can only be made through focused in-situ exploration with a well-instrumented craft. And this craft will be provided revolutionary mobility, nearly global, using in-situ ices as propellants. While other concepts have looked at gathering gases at Mars to propel a hopper, long periods of time are needed to gather the thin CO2 atmosphere. Several gases, mainly nitrogen are on the surface in a readily dense ice form and just need to be picked up, vaporized and used for propellant.

low conductivity materials↗

MMIC DHBT Common-Base Amplifier for 172 GHz

Figure 1 shows a single-stage monolithic microwave integrated circuit (MMIC) power amplifier in which the gain element is a double-heterojunction bipolar transistor (DHBT) connected in common-base configuration. This amplifier, which has been demonstrated to function well at a frequency of 172 GHz, is part of a continuing effort to develop compact, efficient amplifiers for scientific instrumentation, wide-band communication systems, and radar systems that will operate at frequencies up to and beyond 180 GHz. The transistor is fabricated from a layered structure formed by molecular beam epitaxy in the InP/InGaAs material system. A highly doped InGaAs base layer and a collector layer are fabricated from the layered structure in a triple mesa process. The transistor includes two separate emitter fingers, each having dimensions of 0.8 by 12 m. The common-base configuration was chosen for its high maximum stable gain in the frequency band of interest. The input-matching network is designed for high bandwidth. The output of the transistor is matched to a load line for maximum saturated output power under large-signal conditions, rather than being matched for maximum gain under small-signal conditions. In a test at a frequency of 172 GHz, the amplifier was found to generate an output power of 7.5 mW, with approximately 5 dB of large-signal gain (see Figure 2). Moreover, the amplifier exhibited a peak small-signal gain of 7 dB at a frequency of 176 GHz. This performance of this MMIC single-stage amplifier containing only a single transistor represents a significant advance in the state of the art, in that it rivals the 170-GHz performance of a prior MMIC three-stage, four-transistor amplifier. [The prior amplifier was reported in "MMIC HEMT Power Amplifier for 140 to 170 GHz" (NPO-30127), NASA Tech Briefs, Vol. 27, No. 11 (November 2003), page 49.] This amplifier is the first heterojunction- bipolar-transistor (HBT) amplifier built for medium power operation in this frequency band. The performance of the amplifier as measured in the aforementioned tests suggests that InP/InGaAs HBTs may be superior to high-electron-mobility (HEMT) transistors in that the HBTs may offer more gain per stage and more output power per transistor.

Paidi, Vamsi↗

Tracking Object Existence From an Autonomous Patrol Vehicle

An autonomous vehicle patrols a large region, during which an algorithm receives measurements of detected potential objects within its sensor range. The goal of the algorithm is to track all objects in the region over time. This problem differs from traditional multi-target tracking scenarios because the region of interest is much larger than the sensor range and relies on the movement of the sensor through this region for coverage. The goal is to know whether anything has changed between visits to the same location. In particular, two kinds of alert conditions must be detected: (1) a previously detected object has disappeared and (2) a new object has appeared in a location already checked. For the time an object is within sensor range, the object can be assumed to remain stationary, changing position only between visits. The problem is difficult because the upstream object detection processing is likely to make many errors, resulting in heavy clutter (false positives) and missed detections (false negatives), and because only noisy, bearings-only measurements are available. This work has three main goals: (1) Associate incoming measurements with known objects or mark them as new objects or false positives, as appropriate. For this, a multiple hypothesis tracker was adapted to this scenario. (2) Localize the objects using multiple bearings-only measurements to provide estimates of global position (e.g., latitude and longitude). A nonlinear Kalman filter extension provides these 2D position estimates using the 1D measurements. (3) Calculate the probability that a suspected object truly exists (in the estimated position), and determine whether alert conditions have been triggered (for new objects or disappeared objects). The concept of a probability of existence was created, and a new Bayesian method for updating this probability at each time step was developed. A probabilistic multiple hypothesis approach is chosen because of its superiority in handling the uncertainty arising from errors in sensors and upstream processes. However, traditional target tracking methods typically assume a stationary detection volume of interest, whereas in this case, one must make adjustments for being able to see only a small portion of the region of interest and understand when an alert situation has occurred. To track object existence inside and outside the vehicle's sensor range, a probability of existence was defined for each hypothesized object, and this value was updated at every time step in a Bayesian manner based on expected characteristics of the sensor and object and whether that object has been detected in the most recent time step. Then, this value feeds into a sequential probability ratio test (SPRT) to determine the status of the object (suspected, confirmed, or deleted). Alerts are sent upon selected status transitions. Additionally, in order to track objects that move in and out of sensor range and update the probability of existence appropriately a variable probability detection has been defined and the hypothesis probability equations have been re-derived to accommodate this change. Unsupervised object tracking is a pervasive issue in automated perception systems. This work could apply to any mobile platform (ground vehicle, sea vessel, air vehicle, or orbiter) that intermittently revisits regions of interest and needs to determine whether anything interesting has changed.

Wolf, Michael↗

Focal Gray Matter Plasticity as a Function of Long Duration Head-down Tilt Bed Rest

Long duration spaceflight (i.e., > or = 22 days) has been associated with changes in sensorimotor systems, resulting in difficulties that astronauts experience with posture control, locomotion, and manual control. The microgravity environment is an important causal factor for spaceflight induced sensorimotor changes. Whether these sensorimotor changes may be related to structural and functional brain changes is yet unknown. However, experimental studies revealed changes in the gray matter (GM) of the brain after simulated microgravity. Thus, it is possible that spaceflight may affect brain structure and thereby cognitive functioning and motor behavior. Long duration head-down tilt bed rest has been suggested as an exclusionary analog to study microgravity effects on the sensorimotor system. Bed rest mimics microgravity in body unloading and bodily fluid shifts. In consideration of the health and performance of crewmembers both in- and post-flight, we are conducting a prospective longitudinal 70-day bed rest study as an analog to investigate the effects of microgravity on the brain. VBM analysis revealed a progressive decrease from pre- to in- bed rest in GM volume in bilateral areas including the frontal medial cortex, the insular cortex and the caudate. Over the same time period, there was a progressive increase in GM volume in the cerebellum, occipital-, and parietal cortex, including the precuneus. The majority of these changes did not fully recover during the post-bed rest period. Analysis of lobular GM volumes obtained with BRAINS showed significantly increased volume from pre-bed rest to in-bed rest in GM of the parietal lobe and the third ventricle. Temporal GM volume at 70 days in bed rest was smaller than that at the first pre-bed rest measurement. Trend analysis showed significant positive linear and negative quadratic relationships between parietal GM and time, a positive linear relationship between third ventricle volume and time, and a negative linear relationship between cerebellar GM volume and time. FM performance improved from pre-bed rest session 1 to session 2. From the second pre-bed rest measure to the last-day-in-bed rest, there was a significant decrease in performance that only partially recovered post-bed rest. No significant association was observed between changes in brain volume and changes in functional mobility. Extended bed rest, which is an analog for microgravity, can result in local volumetric GM increase and decrease and adversely affect functional mobility. These changes in brain structure and performance were not related in this sample. Whether the effects of bed rest dissipate at longer times post-bed rest, and if they are associated with behavior are important questions that warrant further research including more subjects and longer follow-up times.

Koppelmans, V.↗

Comparison of observed rheological properties of hard wheat flour dough with predictions of the Giesekus-Leonov, White-Metzner and Phan-Thien Tanner models

The measured rheological behavior of hard wheat flour dough was predicted using three nonlinear differential viscoelastic models. The Phan-Thien Tanner model gave good zero shear viscosity prediction, but overpredicted the shear viscosity at higher shear rates and the transient and extensional properties. The Giesekus-Leonov model gave similar predictions to the Phan-Thien Tanner model, but the extensional viscosity prediction showed extension thickening. Using high values of the mobility factor, extension thinning behavior was observed but the predictions were not satisfactory. The White-Metzner model gave good predictions of the steady shear viscosity and the first normal stress coefficient but it was unable to predict the uniaxial extensional viscosity as it exhibited asymptotic behavior in the tested extensional rates. It also predicted the transient shear properties with moderate accuracy in the transient phase, but very well at higher times, compared to the Phan-Thien Tanner model and the Giesekus-Leonov model. None of the models predicted all observed data consistently well. Overall the White-Metzner model appeared to make the best predictions of all the observed data.

Non-NASA Center↗

Weak antilocalization effect due to topological surface states in Bi 2 Se 2.1 Te 0.9

In this work, we have investigated the weak antilocalization (WAL) effect in the p -type Bi 2 Se 2.1 Te 0.9 topological system. The magnetoconductance shows a cusp-like feature at low magnetic fields, indicating the presence of the WAL effect. The WAL curves measured at different tilt angles merge together when they are plotted as a function of the normal field components, showing that surface states dominate the magnetoconductance in the Bi 2 Se 2.1 Te 0.9 crystal. We have calculated magnetoconductance per conduction channel and applied the Hikami-Larkin-Nagaoka formula to determine the physical parameters that characterize the WAL effect. The number of conduction channels and the phase coherence length do not change with temperature up to T = 5 K. In addition, the sample shows a large positive magnetoresistance that reaches 1900% under a magnetic field of 35 T at T = 0.33 K with no sign of saturation. The magnetoresistance value decreases with both increasing temperature and tilt angle of the sample surface with respect to the magnetic field. The large magnetoresistance of topological insulators can be utilized in future technology such as sensors and memory devices.

36 MATERIALS SCIENCE↗

Size-Resolved Density Measurements of Particulate Emissions from an Advanced Combustion Diesel Engine: Effect of Aggregate Morphology

We report the first in situ size-resolved density measurements of particles produced by premixed charge compression ignition (PCCI) and compare these with conventional diesel particles. The densities of size-classified particles were determined by measurements with a differential mobility analyzer (DMA) and an aerosol particle mass analyzer (APM). Particle masses of the different size classes were evaluated with a proposed DMA-APM response function for aggregates. Our results indicate that the effective densities of PCCI and conventional diesel particles were approximately the same for 50 and 100 nm electrical mobility diameters (0.9 and 0.6 g/cc, respectively), but the PCCI particle effective density (0.4 g/cc) was less than the conventional (0.5 g/cc) for 150 nm. The lowest effective particle densities were observed for exhaust gas recirculation (EGR) levels somewhat less than that required for PCCI operation. The inherent densities of conventional particles in the 50 and 100 nm size classes were 1.22 and 1.77 g/cc, which is in good agreement with Park et al. (2004). PCCI inherent particle densities for these same size classes were higher (1.27 and 2.10 g/cc), suggesting that there may have been additional adsorbed liquid hydrocarbons. For 150 nm particles, the inherent densities were nearly the same for PCCI and conventional particles at 2.20 g/cc. We expect that the lower effective density of PCCI particles may improve particulate emissions control with diesel particulate filters (DPFs). The presence of liquid hydrocarbons may also promote oxidation in DPFs.

33 ADVANCED PROPULSION SYSTEMS↗