Search NASA⌕ Search

SEARCH · Search NASA

Results for “catalyst optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80

Spin State Modulation via Magnetic Fields in Fe Single Atom Catalysts for High-Performance Aqueous Zinc–Sulfur Batteries

Aqueous zinc–sulfur battery has garnered significant attention as a high-energy, low-cost, and safe energy storage system. However, the multielectron transfer kinetics of sulfur cathodes are relatively slow, presenting challenges such as limited sulfur utilization and lower discharge voltage, which significantly hinder their practical applications. Here, in this study, we explored a comprehensive design approach for high-performance, long-cycle aqueous zinc–sulfur batteries. The simultaneous introduction of ZnI 2 and Fe single atoms (Fe-SAs) as catalytically active agents decouples the redox reactions, effectively facilitating ZnS oxidation and S reduction separately. The application of an external magnetic field regulates the spin state of Fe-SAs, further enhancing their catalytic activity and electron transfer capability. Electrochemical tests demonstrate that the S@Fe-NC HS/ZnI 2 cathode assembled under a magnetic field exhibits excellent rate performance, achieving an impressive specific capacity of 1399 mAh g –1 at a high current density of 5 A g –1 and good cycling stability over 300 cycles, representing the highest reported high-current discharge capacity to date. This study provides a comprehensive design framework for optimizing zinc–sulfur (Zn–S) battery performance and elucidates the influence of magnetic field-induced spin state modulation on catalytic behavior.

36 MATERIALS SCIENCE↗

PBI nanofiber mat-reinforced anion exchange membranes with covalently linked interfaces for use in water electrolysers

Anion exchange membranes (AEM) are key components in anion exchange membrane water electrolysers. Recently developed materials are less susceptible to the alkaline degradation of the polymer backbone and quaternary ammonium groups. A remaining challenge is the mechanical stability in contact with hot water and dimensional stability when the temperature of the feed solution changes. One solution is to reinforce membranes with a porous support. Since support materials like PEEK or PTFE have a different swelling behavior than the matrix and no strong interactions with the matrix, voids can form, and gas crossover increases. In this work, we approach this issue by pore filling polybenzimidazole nanofiber mats with the bromomethylated precursor of mTPN, an ultra-stable AEM material. During drying, a covalent interaction between support (PBI amine groups) and matrix (-CH 2 Br) is established. After quaternization, the optimized PBI/mTPN-50.120 composite membrane still shows a high conductivity of 62 mS cm –1 , but 37% reduced length swelling in comparison to the non-reinforced membrane. Tensile strength and Young's modulus increase 17% and 56% to 49 MPa and 680 MPa, respectively. In an electrolyser, a stable voltage of 1.98V at 0.25 A cm –2 was achieved, and no change in membrane resistance was observed over the test time of 200 h (50°C, 1 M KOH, catalysts based on Ni/Fe and Mo).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Process intensification for generating and decomposing formic acid, a liquid hydrogen carrier

We preview two processes that facilitate using formic acid (HCOOH) as a liquid hydrogen carrier to store renewably-generated electrical energy and then release it to generate electrical power cleanly for backup or emergency applications. First, we show that simultaneously oxidizing an organic solute (typically a waste stream) can assist the electrochemical synthesis of formic acid by lowering the cell potential. The electrolyser comprises a hybrid 3-chamber PEM stack that reduces CO₂ via a gas-diffusion cathode boosted by the oxidation of aqueous methanol. However, the extent of the boosting needs to be optimized across the whole operation of the cell. Next, we present results from an intensified reactor for decomposing formic acid back into H₂ and CO₂ at elevated pressure so that the H₂ can be used in a fuel cell. The reactor combines three operations: Vaporization of the formic acid, its decomposition, and separation of the product stream. Their close coupling affords energy savings and a compact design that could be mounted on a mobile skid. We briefly discuss the electrode catalyst that facilitates the first process and two thermally activated catalysts (Ir supported on covalent triazine framework and Pd supported on carbon) that enable the second process.

25 ENERGY STORAGE↗

Reactivity descriptors in acid catalysis: acid strength, proton affinity and host–guest interactions

Brønsted acids mediate chemical transformations via proton transfer to bound species and interactions between the conjugate anion and bound cationic intermediates and transition states that are also stabilized by van der Waals forces within voids of molecular dimensions in inorganic hosts. This Feature Article describes the relevant descriptors of reactivity in terms of the properties of acids and molecules that determine their ability to donate and accept protons and to reorganize their respective charges to optimize their interactions at bound states. The deprotonation energy (DPE) of the acids and the protonation energy (Eprot) of the gaseous analogs of bound intermediates and transition states reflect their respective properties as species present at non-interacting distances. These properties accurately describe the reactivity of acids of a given type, such as polyoxometalates (POM) with a given type of addenda atom but different central atoms and heterosilicates, for different families of reactions. They do not fully capture, however, differences among acid types (e.g., Mo and W POM, heterosilicates, mineral acids) for diverse types of chemical transformations (e.g., elimination, isomerization, dimerization, condensation). The incompleteness of such descriptors reflects their inability to describe how protonated molecular species and conjugate anions restructure their respective charges when present as a binding pair at interacting distances. Such interaction energies represent electrostatic forces that depend on charge distributions in the cations and anions and the ability to reorganize the distributions to maximize the interactions. In the case of deprotonation, the electrostatic and charge reorganization components of DPE for various acids solely reflect the ability of the conjugate anion to accept and distribute the negative charge, a characteristic unique of each type of solid acid and specifically of the composition of its extended conjugate anion framework. The energy required to accept and rearrange the positive charge in bound intermediates and transition states reflects, in turn, their respective ability to recover the ionic and covalent components of DPE, the energy required to detach proton from conjugate anions. The DPE components and the recovery fractions together lead to a modified DPE, which captures only the part of DPE that remains unrecovered by the ion-pair interactions at bound intermediates and transition states, as the unifying descriptor for broad families of acids and reactions. The electrostatic and charge reorganization energies involved in these general descriptors are placed in historical context by assessing their connections to the heuristics of hard–soft acid–base displacements. Further development of these concepts requires benchmarking and extension of electrostatic and reorganization components of energies for a more diverse set of reaction types and acid families and advancement of methods for more efficient calculations of electrostatic interactions. Reactivity descriptors must also account for dispersive interactions between host cavities and guest molecules, requiring a framework analogous to the one described here for ion-pair interactions; these dispersive interactions depend on the fit between their shapes and sizes as well as their ‘‘structural stiffness’’ that determines the ability to modify the shapes of molecules and voids to minimize free energy. Entropy considerations and estimates of their dependence on properties of catalysts and molecules are also required for accurately determining Gibbs free energies that ultimately determine reaction rates.

Deshlahra, Prashant↗

Reconstruction of Thiospinel to Active Sites and Spin Channels for Water Oxidation

Water electrolysis is a promising technique for carbon neutral hydrogen production. A great challenge remains at developing robust and low-cost anode catalysts. Many pre-catalysts are found to undergo surface reconstruction to give high intrinsic activity in the oxygen evolution reaction (OER). The reconstructed oxyhydroxides on the surface are active species and most of them outperform directly synthesized oxyhydroxides. The reason for the high intrinsic activity remains to be explored. Here, a study is reported to showcase the unique reconstruction behaviors of a pre-catalyst, thiospinel CoFe 2 S 4 , and its reconstruction chemistry for a high OER activity. The reconstruction of CoFe 2 S 4 gives a mixture with both Fe–S component and active oxyhydroxide (Co(Fe)O x H y ) because Co is more inclined to reconstruct as oxyhydroxide, while the Fe is more stable in Fe–S component in a major form of Fe 3 S 4 . The interface spin channel is demonstrated in the reconstructed CoFe 2 S 4 , which optimizes the energetics of OER steps on Co(Fe)O x H y species and facilitates the spin sensitive electron transfer to reduce the kinetic barrier of O–O coupling. The advantage is also demonstrated in a membrane electrode assembly (MEA) electrolyzer. Finally, this work introduces the feasibility of engineering the reconstruction chemistry of the precatalyst for high performance and durable MEA electrolyzers.

36 MATERIALS SCIENCE↗

Morphology and Activity Tuning of Cu 3 Pt/C Ordered Intermetallic Nanoparticles by Selective Electrochemical Dealloying

Improving the catalytic activity of Pt-based bimetallic nanoparticles is a key challenge in the application of proton-exchange membrane fuel cells. Electrochemical dealloying represents a powerful approach for tuning the surface structure and morphology of these catalyst nanoparticles. We present a comprehensive study of using electrochemical dealloying methods to control the morphology of ordered Cu 3 Pt/C intermetallic nanoparticles, which could dramatically affect their electrocatalytic activity for the oxygen reduction reaction (ORR). Depending on the electrochemical dealloying conditions, the nanoparticles with Pt-rich core–shell or porous structures were formed. We further demonstrate that the core–shell and porous morphologies can be combined to achieve the highest ORR activity. Lastly, this strategy provides new guidelines for optimizing nanoparticles synthesis and improving electrocatalytic activity.

36 MATERIALS SCIENCE↗

De novo design of a fluorescence-activating β-barrel

The regular arrangements of β-strands around a central axis in β-barrels and of α-helices in coiled coils contrast with the irregular tertiary structures of most globular proteins, and have fascinated structural biologists since they were first discovered. Simple parametric models have been used to design a wide range of α-helical coiled-coil structures, but to date there has been no success with β-barrels. Here we show that accurate de novo design of β-barrels requires considerable symmetry-breaking to achieve continuous hydrogen-bond connectivity and eliminate backbone strain. We then build ensembles of β-barrel backbone models with cavity shapes that match the fluorogenic compound DFHBI, and use a hierarchical grid-based search method to simultaneously optimize the rigid-body placement of DFHBI in these cavities and the identities of the surrounding amino acids to achieve high shape and chemical complementarity. The designs have high structural accuracy and bind and fluorescently activate DFHBI in vitro and in Escherichia coli, yeast and mammalian cells. Finally, this de novo design of small-molecule binding activity, using backbones custom-built to bind the ligand, should enable the design of increasingly sophisticated ligand-binding proteins, sensors and catalysts that are not limited by the backbone geometries available in known protein structures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Monodisperse Pt{sub 3}Co nanoparticles as electrocatalyst : the effects of particle size and pretretment on electrocatalytic reduction of oxygen.

Monodisperse Pt{sub 3}Co nanoparticles have been synthesized with size control via an organic solvothermal approach. The obtained nanoparticles were incorporated into a carbon matrix and applied as electrocatalysts for the oxygen reduction reaction to investigate the effects of particle size and pretreatment on their catalytic performance. It has been found that the optimal conditions for maximum mass activity were with particles of {approx}4.5 nm and a mild annealing temperature of about 500 C. While the particle size effect can be correlated to the average surface coordination number, Monte Carlo simulations have been introduced to depict the nanoparticle structure and segregation profile, which revealed that the annealing temperature has a direct influence on the particle surface relaxation, segregation and adsorption/catalytic properties. The obtained fundamental understanding of activity enhancement in Pt-bimetallic alloy catalysts could be utilized to guide the development of advanced nanomaterials for catalytic applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

RNA-Cleaving DNA Enzymes with Altered Regio- or Enantioselectivity

In vitro evolution methods were used to obtain DNA enzymes that cleave either a 2',5' - phosphodiester following a wibonucleotide or a 3',5' -phosphodiester following an L-ribonucleotide. Both enzymes can operate in an intermolecular reaction format with multiple turnover. The DNA enzyme that cleaves a 2',5' -phosphodiester exhibits a k(sub cat) of approx. 0.01/ min and catalytic efficiency, k(sub cat)/k(sub m) of approx. 10(exp 5)/ M min. The enzyme that cleaves an L-ribonudeotide is about 10-fold slower and has a catalytic efficiency of approx. 4 x 10(exp 5)/ M min. Both enzymes require a divalent metal cation for their activity and have optimal catalytic rate at pH 7-8 and 35-50 C. In a comparison of each enzyme s activity with either its corresponding substrate that contains an unnatural ribonudeotide or a substrate that instead contains a standard ribonucleotide, the 2',5' -phosphodiester-deaving DNA enzyme exhibited a regioselectivity of 6000- fold, while the L-ribonucleotide-cleaving DNA enzyme exhibited an enantioselectivity of 50-fold. These molecules demonstrate how in vitro evolution can be used to obtain regio- and enantioselective catalysts that exhibit specificities for nonnatural analogues of biological compounds.

Ordoukhanian, Phillip↗

Static Controls Performance Tool for Lunar Landers

This document presents a static analysis tool used to evaluate the controllability of Lunar landers. This was created as part of the NASA Lunar Cargo Transportation and Landing by Soft Touchdown (Lunar CATALYST) program. This tool is capable of accepting typical design information such as location and direction of thrusters, maximum thruster forces, gravity vectors, and center of mass locations. The tool evaluates how far the center of gravity can move from its starting position while still maintaining control. This type of analysis is intended to support results produced by time domain simulations. The code created for this project was implemented in Python, and it was designed to be integrated into systems level optimization tools to yield first-cut results on optimal thruster placement.

Aretskin-Hariton, Eliot D.↗

In situ ethyl ester production from wet algal biomass under microwave-mediated supercritical ethanol conditions

An in situ transesterification approach was demonstrated for converting lipid-rich wet algae (Nannochloropsis salina) into fatty acid ethyl esters (FAEE) under microwave-mediated supercritical ethanol conditions, while preserving the nutrients and other valuable components in the algae. This single-step process can simultaneously and effectively extract the lipids from wet algae and transesterify them into crude biodiesel. Experimental runs were designed to optimize the process parameters and to evaluate their effects on algal biodiesel yield. The algal biomass characterization and algal biodiesel analysis were carried out by using various analytical instruments such as FTIR, SEM-EDS, TLC, GC-MS and transmission electron microscopy (TEM). The thermogravimetric analysis (TGA) under nitrogen and oxygen environments was also performed to examine the thermal and oxidative stability of ethyl esters produced from wet algae. This simple in situ transesterification process using a green solvent and catalyst-free approach can be a potentially efficient route for algal biodiesel production.

09 BIOMASS FUELS↗

Programmable simulations of molecules and materials with reconfigurable quantum processors

Simulations of quantum chemistry and quantum materials are believed to be among the most important applications of quantum information processors. However, realizing practical quantum advantage for such problems is challenging because of the prohibitive computational cost of programming typical problems into quantum hardware. Here we introduce a simulation framework for strongly correlated quantum systems represented by model spin Hamiltonians that uses reconfigurable qubit architectures to simulate real-time dynamics in a programmable way. Our approach also introduces an algorithm for extracting chemically relevant spectral properties via classical co-processing of quantum measurement results. We develop a digital–analogue simulation toolbox for efficient Hamiltonian time evolution using digital Floquet engineering and hardware-optimized multi-qubit operations to accurately realize complex spin–spin interactions. As an example, we propose an implementation based on Rydberg atom arrays. In addition, we show how detailed spectral information can be extracted from the dynamics through snapshot measurements and single-ancilla control, enabling the evaluation of excitation energies and finite-temperature susceptibilities from a single dataset. To illustrate the approach, we show how to use the method to compute key properties of a polynuclear transition-metal catalyst and two-dimensional magnetic materials.

74 ATOMIC AND MOLECULAR PHYSICS↗

(Invited) Virtual Analysis of Gas-Diffusion-Electrode CO 2 Electrolyzers

The electrochemical reduction of CO 2 (CO 2 R) to value-added products is an attractive technology for tackling the rising atmospheric CO 2 levels and storing intermittent renewable energy into chemical bonds. Fundamental understanding of CO 2 R has progressed significantly in recent years and is critical in the development of CO 2 R to liquid-fuel electrolyzers, where gas-diffusion electrodes (GDEs) have been shown to be key enabling architectures. Various designs have been proposed and studied in the literature to enhance overall selectivity, rates, and maximize the conversion of CO 2 , the latter of which is only now being recognized as a critical issue. In this respect, there is a need to explore the governing phenomena inherent in these architectures to enable optimization. Mathematical modeling is ideally suited to tackle and explore these multiphysics interactions and provide virtual design analysis. In this talk, we discuss modeling methodologies and physics inherent in these devices and present our recent modeling of GDEs for CO 2 reduction. We specifically examine the impacts of multiphase flow and related phenomena on overall cell performance. We then explore the performance and limitations of various cell designs guided by simulation results and examine potential methods for improving water management and tuning catalyst selectivity including the use of different anion-exchange and bipolar membranes. Finally, we discuss the disparities in local environments between aqueous and GDE devices and propose strategies to reduce the gap in knowledge between the two systems.

42 ENGINEERING↗

Manipulating Surface Termination of Perovskite Manganate for Oxygen Activation

For ABO 3 perovskite oxides, one of the key issues limiting their utilization in heterogeneous catalysis is the dominant presence of catalytically inactive A-site cations at the surface. The engineering of B-site terminated perovskites is considered as an effective method to address this issue, especially when dealing with Mn/Co-based perovskite catalysts. However, to date, such a strategy has not been fully successful and remains a major challenge in the field. Herein, a Mn-terminated La 0.45 Sr 0.45 MnO 3 (B-LSM) is successfully synthesized via a one-pot hydrothermal method, in which low-valence Mn ions partially occupy the A site to form the active Mn-excess phase. Additionally, experimental results and theoretical calculations reveal that the presence of the surface Mn termination in B-LSM optimizes the hybrid orbitals of Mn 3d-O 2p and promotes the activation of surface lattice oxygen, where the pristine inert lattice O 2- is evolved into active and stable lattice O 2-x . Such structural optimization significantly reduces the activation energy barriers on going from O 2 ⁻ species to important intermediate O - species during O 2 activation. Moreover, this results in good stability and Pt-like activity for the B-LSM during CO oxidation. This work offers a new chemical route for the design of advanced perovskite-type oxides possessing novel functions.

36 MATERIALS SCIENCE↗

Virtual Analysis of Gas-Diffusion-Electrode CO 2 Electrolyzers

The electrochemical reduction of CO 2 (CO2R) to value-added products is an attractive technology for tackling the rising atmospheric CO 2 levels and storing intermittent renewable energy into chemical bonds. Fundamental understanding of CO 2 R has progressed significantly in recent years and is critical in the development of CO 2 R to liquid-fuel electrolyzers, where gas-diffusion electrodes (GDEs) have been shown to be key enabling architectures. Various designs have been proposed and studied in the literature to enhance overall selectivity, rates, and maximize the conversion of CO 2 , the latter of which is only now being recognized as a critical issue. In this respect, there is a need to explore the governing phenomena inherent in these architectures to enable optimization. Mathematical modeling is ideally suited to tackle and explore these multiphysics interactions and provide virtual design analysis. In this talk, we discuss modeling methodologies and physics inherent in these devices and present our recent modeling of GDEs for CO 2 reduction. Here, we specifically examine the impacts of multiphase flow and related phenomena on overall cell performance. We then explore the performance and limitations of various cell designs guided by simulation results and examine potential methods for improving water management and tuning catalyst selectivity including the use of different anion-exchange and bipolar membranes. Finally, we discuss the disparities in local environments between aqueous and GDE devices and propose strategies to reduce the gap in knowledge between the two systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The TASAR Project: Launching Aviation on an Optimized Route Toward Aircraft Autonomy

The Traffic Aware Strategic Aircrew Request (TASAR) concept applies onboard automation for the purpose of advising the pilot of route modifications that would be beneficial to the flight. Leveraging onboard computing platforms with connectivity to avionics and diverse data sources on and off the aircraft, TASAR introduces a new, powerful capability for in-flight trajectory management to the cockpit and its flight crew that is anticipated to induce a significant culture change in airspace operations. Flight crews empowered by TASAR and its derivative technologies could transform from today’s flight plan followers to proactive trajectory managers, taking an initial critical step towards increasing autonomy in the airspace system. TASAR was developed as a catalyst for operational autonomy, a future vision where the responsibilities and authorities of trajectory management reside with the aircraft operator and are distributed among participating aircraft, thus fulfilling a vision dating back decades and enabling a fully scalable airspace system. This NASA Technical Paper maps TASAR to its foundational vision and traces its research and development from initial concept generation to an operational evaluation by a U.S. airline in revenue service, the final stage before technology transfer and commercialization.

Wing, David J.↗

Size and Temperature Dependence of Electron Transfer between CdSe Quantum Dots and a TiO 2 Nanobelt

Understanding charge transfer reactions between quantum dots (QD) and metal oxides is fundamental for improving photocatalytic, photovoltaic and electronic devices. The complexity of these processes makes it difficult to find an optimum QD size with rapid charge injection and low recombination. We combine time-domain density functional theory with nonadiabatic molecular dynamics to investigate the size and temperature dependence of the experimentally studied electron transfer and charge recombination at CdSe QD-TiO 2 nanobelt (NB) interfaces. The electron injection rate shows strong dependence on the QD size, increasing for small QDs. The rate exhibits Arrhenius temperature dependence, with the activation energy of the order of millielectronvolts. The charge recombination process occurs due to coupling of the electronic subsystem to vibrational modes of the TiO 2 NB. Inelastic electron-phonon scattering happens on a picosecond time scale, with strong dependence on the QD size. Our simulations demonstrate that the electron-hole recombination rate decreases significantly as the QD size increases, in excellent agreement with experiments. The temperature dependence of the charge recombination rates can be successfully modeled within the framework of the Marcus theory through optimization of the electronic coupling and the reorganization energy. Our simulations indicate that by varying the QD size, one can modulate the photoinduced charge separation and charge recombination, fundamental aspects of the design principles for high efficiency devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Photocatalytic water splitting—The untamed dream: A review of recent advances

Here, photocatalytic water splitting using sunlight is a promising technology capable of providing high energy yield without pollutant byproducts. Herein, we review various aspects of this technology including chemical reactions, physiochemical conditions and photocatalyst types such as metal oxides, sulfides, nitrides, nanocomposites, and doped materials followed by recent advances in computational modeling of photoactive materials. As the best-known catalyst for photocatalytic hydrogen and oxygen evolution, TiO 2 is discussed in a separate section, along with its challenges such as the wide band gap, large overpotential for hydrogen evolution, and rapid recombination of produced electron-hole pairs. Various approaches are addressed to overcome these shortcomings, such as doping with different elements, heterojunction catalysts, noble metal deposition, and surface modification. Development of a photocatalytic corrosion resistant, visible light absorbing, defect-tuned material with small particle size is the key to complete the sunlight to hydrogen cycle efficiently. Computational studies have opened new avenues to understand and predict the electronic density of states and band structure of advanced materials and could pave the way for the rational design of efficient photocatalysts for water splitting. Future directions are focused on developing innovative junction architectures, novel synthesis methods and optimizing the existing active materials to enhance charge transfer, visible light absorption, reducing the gas evolution overpotential and maintaining chemical and physical stability

36 MATERIALS SCIENCE↗