Search NASA⌕ Search

SEARCH · Search NASA

Results for “cathode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80

Study of the feasibility of distributed cathodic arc as a plasma source for development of the technology for plasma separation of SNF and radioactive wastes

One of the key problems in the development of plasma separation technology is designing a plasma source which uses condensed spent nuclear fuel (SNF) or nuclear wastes as a raw material. This paper covers the experimental study of the evaporation and ionization of model materials (gadolinium, niobium oxide, and titanium oxide). For these purposes, a vacuum arc with a heated cathode on the studied material was initiated and its parameters in different regimes were studied. During the experiment, the cathode temperature, arc current, arc voltage, and plasma radiation spectra were measured, and also probe measurements were carried out. It was found that the increase in the cathode heating power leads to the decrease in the arc voltage (to 3 V). This fact makes it possible to reduce the electron energy and achieve singly ionized plasma with a high degree of ionization to fulfill one of the requirements for plasma separation of SNF. This finding is supported by the analysis of the plasma radiation spectrum and the results of the probe diagnostics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Experimental study of the plasma effect on the generation of microwave radiation in systems with a virtual cathode

Results are presented from experimental studies of the plasma effect on the generation of microwave radiation in systems with a virtual cathode. Using a triode with a virtual cathode as an example, it is shown that the cathode and anode plasmas reduce the generation efficiency; in particular, the power of the generated microwave radiation decreases and the radiation frequency and the microwave pulse duration change appreciably. It is demonstrated that, at high microwave powers, the power radiated into free space can be reduced by the plasma generated at the surface of the output window. This plasma appears due to discharges developing on the window surface under the combined action of bremsstrahlung, UV radiation, electrons and ions arriving from the beam formation zone, and the microwave electric field.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Simulation of oscillatory processes in a beam-plasma system with a virtual cathode in gas-filled interaction space

Physical processes occurring in an intense electron beam with a virtual cathode in an interaction space filled with neutral gas are studied in a two-dimensional model. A mathematical model is proposed for investigating complicated self-consistent processes of neutral gas ionization by the beam electrons and the dynamics of an electron beam and heavy positive ions in the common space charge field with allowance for the two-dimensional motion of charged particles. Three characteristic dynamic regimes of the system are revealed: complete suppression of oscillations of the virtual cathode as a result of neutralizing its space charge by positive ions; the pulsed generation regime, in which the ions dynamics repeatedly suppresses and restores the virtual cathode oscillations; and the continuous generation regime with an anomalously high level of noisy oscillations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Specific features of an electric discharge operating between an electrolytic anode and a metal cathode

Results are presented from experimental studies of a high-current electric discharge operating between an St45 steel cathode and a service water anode in a wide range of air pressures. Peculiarities of discharge ignition and specific features of cathode and anode spots were revealed. The behavior of the current density on a service water anode was investigated for the first time. Comparison of the current densities j on the steel cathode and service water anode shows that, in the parameter range under study, Hehl's law is not satisfied on the water anode. The two-dimensional distribution of the potential inside and on the surface of the service water anode was measured.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Expansion of the cathode spot and generation of shock waves in the plasma of a volume discharge in atmospheric-pressure helium

The expansion of the cathode spot and the generation of shock waves during the formation and development of a pulsed volume discharge in atmospheric-pressure helium were studied by analyzing the emission spectra of the cathode plasma and the spatiotemporal behavior of the plasma glow. The transition of a diffuse volume discharge in a centimeter-long gap into a high-current diffuse mode when the gas pressure increased from 1 to 5 atm and the applied voltage rose from the statistical breakdown voltage to a 100% overvoltage was investigated. Analytical expressions for the radius of the cathode spot and its expansion velocity obtained in the framework of a spherically symmetric model agree satisfactorily with the experimental data.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Specific features of virtual cathode formation and dynamics with allowance for the magnetic self-field of a relativistic electron beam

The conditions and mechanisms of virtual cathode formation in relativistic and ultrarelativistic electron beams are analyzed with allowance for the magnetic self-field for different magnitudes of the external magnetic field. The typical behavior of the critical current at which an oscillating virtual cathode forms in a relativistic electron beam is investigated as a function of the electron energy and the magnitude of the uniform external magnetic field. It is shown that the conditions for virtual cathode formation in a low external magnetic field are determined by the influence of the magnetic self-field of the relativistic electron beam. In particular, azimuthal instability of the electron beam caused by the action of the beam magnetic self-field, which leads to a reduction in the critical current of the relativistic electron beam, is revealed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Study of a DC gas discharge with a copper cathode in a water flow

A dc gas discharge between copper electrodes in the current range of 5–20 А was studied experimentally. The discharge gap length was varied within 45–70 mm. The cathode was a 10-mm-diameter rod placed in the water flowing out from a dielectric tube. Three discharge configurations differing in the position of the cathode upper end with respect to the water surface were considered: (i) above water; (ii) flush with the water surface, and (iii) under water. The electric and optical characteristics of the discharge in the second configuration were studied in more detail. It is established that the discharge properties are similar to those of an electric arc. Considerable cathode erosion was observed in the third configuration. It is revealed that fine-dispersed copper grains form in the course of erosion.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Formation of ncl-Si in the Amorphous Matrix a-SiO{sub x}:H Located near the Anode and on the Cathode, Using a Time-Modulated DC Plasma with the (SiH{sub 4}–Ar–O{sub 2}) Gas Phase (C{sub O{sub 2}} = 21.5 mol %)

The formation of ncl-Si in the amorphous matrix a-SiO{sub x}:H using a time-modulated DC plasma at an elevated oxygen content of C{sub O{sub 2}} = 21.5 mol % in a gas mixture of (SiH{sub 4}–Ar–O{sub 2}) is investigated. Plasma modulation implies the repeated (n = 180) switching on (for t{sub on} = 5, 10, 15 s) and switching off (for t{sub off} = 5, 10, 15 s) of the magnet coil of the DC magnetron. The effect of self-induction is used to enhance the processes of SiH{sub 4} dissociation, the formation of Si nanoparticles, and the ionization of oxygen and ncl-Si flows towards the electrodes. The samples are located both on an electrically isolated substrate holder near the anode and on the cathode (beyond its erosion zone). These experiments show that the shape of the dependences of the photoluminescence intensity I{sub PL}{sup ncl−Si} on the wavelength Λ are identical for all pairs of samples on the anode and cathode. When the t{sub on} value is small (t{sub on} = 5 s), the difference in the sample location only slightly affects the infrared (IR) spectra. At longer times t{sub on} (≥10 s) and a short time t{sub off} (5 s), the amorphous matrix located on the cathode is enriched with oxygen (as compared with that near the anode). The optimal plasma-modulation parameters are found to be t{sub off}/t{sub on} = 5, 10, 15/10 and t{sub off}/t{sub on} = 5, 10/15; under these conditions, the amorphous matrix has a “perfect structure” and is transparent to radiation, and the I{sub PL}{sup ncl−Si} value is the largest in the range λ ≈ 0.75–0.9 μm.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Analysis of the Behavior of Individual Emission Sites on the Surface of a Multi-Tip Field Cathode

A method of analysis of the surface of multi-tip field cathodes using data obtained with the aid of a computer-controlled field emission projector and a system of fast high-voltage scanning is described. An investigation of a polymer/carbon nanotube composite field electron emitter by this method was used to determine the distribution of individual emission sites over the surface of a multi-tip field cathode and to estimate variation of the work function of separate emission sites depending on the applied voltage. The contributions of separate groups of emission sites to a change of the shape of current–voltage characteristic of a multi-tip cathode have been numerically estimated.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

FTIR and Raman Study of the LixTiyMn1-yO2 (y = 0, 0.11) Cathodes in Methylpropyl Pyrrolidinium Bis(fluoro-sulfonyl)imide, LiTFSI Electrolyte

This work demonstrates the protective effect of partial titanium substitution in Li{sub x}Ti{sub 0.11}Mn{sub 0.89}O{sub 2} against surface decomposition in room-temperature ionic liquid (RTILs) cells. Raman microscopy and reflectance Fourier transform IR (FTIR) spectroscopy were used to analyze electrodes recovered from cycled Li/Li{sub x}Ti{sub y}Mn{sub 1-y}O{sub 2} (y=0, 0.11) cells containing the 0.5 mol/kg LiTFSI in P{sub 13}FSI RTIL electrolyte. [TFSI=bis(trifluoromethanesulfonyl)imide.] Raman and FTIR spectra of cycled Li{sub x}MnO{sub 2} cathodes showed many distinct bands that can be attributed to both the electrolyte and electrode decomposition products. The thickness of the amorphous porous layer on the Li{sub x}MnO{sub 2} cathode increased during cycling. The surface degradation of Li{sub x}MnO{sub 2} and precipitation of electrolyte decomposition products contributed to the film growth. Improved cycling behavior was observed in cells containing Li{sub x}Ti{sub 0.11}Mn{sub 0.89}O{sub 2}, yet Raman spectroscopy also showed possible surface degradation. The FTIR spectra of cycled Li{sub x}MnO{sub 2} and Li{sub x}Ti{sub 0.11}Mn{sub 0.89}O{sub 2} cathodes displayed bands characteristic for LiSO{sub 3}CF{sub 3} and Li{sub 2}NSO{sub 2}CF{sub 3}, which originate from the reaction of the TFSI anion with traces of water present in the cell.

25 ENERGY STORAGE↗

Beneficial Effect of Li 5 FeO 4 Lithium Source for Li-Ion Batteries with a Layered NMC Cathode and Si Anode

The energy density of lithium-ion batteries can be increased by replacing the traditional graphite anode with a high capacity silicon anode. However, volume changes and interfacial instabilities cause a large irreversible capacity and a continual loss of lithium during cycling, which lead to rapid capacity loss. In this work, we add Li 5 FeO 4 (LFO) to a LiNi 0.5 Mn 0.3 Co 0.2 O 2 (NMC) cathode as a pre-lithiation additive, which increases the lithium inventory and extends the cycle life of Si-graphite/NMC full cells, and decreases the NMC particle degradation. LFO delivers a large 764 mAh g –1 LFO capacity below 4.7 V vs Li/Li + . By tuning the LFO content in Si-graphite/LFO-NMC full cells, we show higher capacity, improved retention, lower impedance, and superior rate performance compared to full cells without LFO. Post-test characterizations demonstrate that LFO inclusion in the cathode matrix leads to less NMC secondary particle segregation/cracking and a thinner surface reduced layer on the NMC particles. The beneficial effects of LFO endure after the lithium reserve has been exhausted, highlighting a lasting synergy between the lithium source and electrode active materials. This study introduces a new approach to simultaneously increase lithium inventory and reduce cathode degradation, and makes critical advances toward enabling Si anodes for lithium-ion batteries.

25 ENERGY STORAGE↗

Probing Anion Exchange Membrane Fuel Cell Cathodes by Varying Electrocatalysts and Electrode Processing

To date, several high-performing anion exchange membrane fuel cells (AEMFCs) have been demonstrated, but most these studies have focused on Pt containing cathodes with high loadings. Here, we explore and compare the performance and perform electrochemical diagnostics on three leading AEMFC cathode electrocatalysts: Pt/C, Ag/C, and Fe–N–C with electrodes that have been processed with either powder or dispersion-based ionomers using perfluorinated anion exchange polymers. Pt/C had the highest performance but also showed a strong dependence on ionomer type, with powder ionomer exhibiting much higher performance. These results were consistent with the observations for Ag/C but did not hold for the Fe–N–C catalyst where almost no change was observed between powder and dispersion-based ionomers. This is the first-time the impact of powder and dispersion ionomer with different classes of cathode electrocatalysts on the fuel cell performance have been compared, and the results have strong implications for the ability to achieve high performance at low loadings and for better understanding catalyst-ionomer interactions within AEMFCs.

30 DIRECT ENERGY CONVERSION↗

The Influence of Cr-Additives on the Polarization Resistance of Praseodymium-Doped Ceria Cathodes for Solid Oxide Fuel Cells

While Cr poisoning of the oxygen reduction reaction (ORR) at SOFC cathodes is widely agreed to involve deactivation of oxygen exchange sites, the degradation mechanism remains ambiguous. Here, we selected an alternative cathode material Pr 0.1 Ce 0.9 O 2− δ , free of Sr segregation, to systematically investigate the effect of Cr-induced degradation in ORR. We expand on our previous studies in which the acidity/basicity of binary additives was found to be a strong indicator of the rate of oxygen surface exchange, by electrochemically investigating the ORR activity of the PCO cathode by impedance spectroscopy. Serial infiltration with acidic Cr-based oxides was found to degrade ORR activity as reflected in a 20-fold increase in area specific resistance (ASR) without corresponding changes in activation energy, with the opposite trend obtained with Ca-based oxides. Detected changes in total capacitance, attributed to changes in surface capacitance, also suggest depressed/enhanced PCO surface redox behavior with Cr/Ca-based infiltrants. Taken together, these results point to a more universal source of ORR poisoning/activation, based on acidity/basicity, rather than physical blocking of active sites. With this improved understanding, one can expect progress to be made in the coming years in optimizing means for protecting catalytic surfaces from degradation and/or improving their performance.

25 ENERGY STORAGE↗

Electrolyte Study for High-Nickel LiNi 0.9 Mn 0.05 Co 0.05 O 2 Cathodes

With an increasing demand for intermittent renewable energy and electric vehicles, it is imperative to develop lithium-ion batteries with Earth-abundant cathode materials. Cobalt (Co) is preferred to be kept at a minimum because of its high cost and limited mining options, yet it has played an essential role in the high-performance transition metal oxides (TMOs). Herein, we report work from Argonne National Laboratory, conducted under the U.S. DoE's Vehicle Technologies Office, Deep Dive consortium on Next-Generation Cathodes, to optimize electrolytes for LiNi 0.9 Mn 0.05 Co 0.05 O 2 . LiNi 0.9 Mn 0.05 Co 0.05 O 2 is a high-Ni TMO benchmark as it outperforms most other TMOs under standard cycling conditions. In this study, we use the figure-of-merit approach to optimize electrolytes for this novel cathode material. Dual-salt carbonate electrolytes containing lithium difluorooxyphosphate and hexafluorophosphates were found to be the best for capacity retention and slowing the impedance rise. Importantly, transition metal dissolution and lithium inventory losses in the solid electrolyte interface were found to be the major causes for capacity fade.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The Interaction between Cu and Fe in P2-Type Na x TMO 2 Cathodes for Advanced Battery Performance

Recently, Cu element has been introduced into layered sodium transition metal oxides (NaxTMO2) as cathode materials for sodium ion batteries to engineer rate and cycling performance. To study the unique role provided by Cu, we designed, synthesized and tested four different compositions of P2-type Nax(MnyFezCo1-y-z)O2 and three compositions of P2-type Nax(MnyFezCu1-y-z)O2 cathode materials. When cycled in the full voltage range of 1.5~4.5 V under different rates 0.1 C, 1 C and 10 C, the cyclability of MnFeCu-based compounds is better than that of MnFeCo-based ones. Using X-ray diffraction, we observed the P2 to O2-like phase transition of MnFeCu-based materials upon charging and studied its influence on battery performance. Limiting the P2-O2 phase transition delivers less capacity, but improves cyclability. By DFT simulations, we showed that different Na diffusivity and site preference in the high voltage phase contribute to the difference in the electrochemical performances of these cathode materials.

25 ENERGY STORAGE↗

Communication—O3-Type Layered Oxide with a Quaternary Transition Metal Composition for Na-Ion Battery Cathodes: NaTi 0.25 Fe 0.25 Co 0.25 Ni 0.25 O 2

NaTi 0.25 Fe 0.25 Co 0.25 Ni 0.25 O 2 is explored as a cathode material for Na-ion batteries. Synthesized by a solid-state reaction, the compound is phase-pure with the O3-type layered structure and consists of Ti 4+ , Fe 3+ , Co 3+ , and Ni 2+ according to X-ray absorption spectroscopy. The cathode delivers 163 mAh/g and 504 Wh/kg at C/20 in the first discharge with 89% capacity retention after 20 cycles and demonstrates superior rate capability with micron sized particles, in which discharge capacity at 30 C is 80mAh/g. Our results indicate that the Ti-containing quaternary material can be a potential cathode composition for Na-ion batteries.

25 ENERGY STORAGE↗

Enhanced Raman Scattering from NCM523 Cathodes Coated with Electrochemically Deposited Gold

Materials with the general composition LiMO2, where M is a mix of nickel, cobalt, and manganese, have been studied extensively as cathodes for lithium-based electrochemical cells. Some compositions, like LiNi0.5Co0.2Mn0.3O2 (NCM523), have already found application in commercial lithium-ion batteries. Pre-test and post-test analyses of these types of cathodes have benefited greatly from the use of Raman spectroscopy. Specifically, Raman spectroscopy can be used to investigate the phonons of the LiMO2 lattice. This is particularly useful for studies of the LiMO2 after it has been formed into the type of polymer-bonded laminate from which typical battery cathodes are cut. One of the problems that occurs in such studies is that the scattering from the LiMO2 phase gets progressively weaker as the nickel content increases. NCM523 poses one example of this behavior owing to the fact that half of the transition metal content is nickel. In this study we show that the intensity of the Raman scattering from the NCM523 phonons can be significantly increased by electroplating clusters of sub-micron gold particles on NCM523-containing laminate structures. The gold appears to plate somewhat selectively on the NCM523 particles in randomly sized clusters. These clusters stimulate the Raman scattering from the NCM523 to varying extents that can reach nearly 100 times the scattering intensity from uncoated pristine laminates.

cathode↗

In Situ Monitoring of the Growth of Nickel, Manganese, and Cobalt Hydroxide Precursors during Co-Precipitation Synthesis of Li-Ion Cathode Materials

The electrochemical performance of cathode materials for Li-ion batteries depends on the morphology of the material, which, in turn, depends on the synthesis conditions. Very few studies have focused on the impact of process conditions on the final morphology of the cathode particles and analyzed the growth during synthesis. In this paper, the evolution of nickel, manganese, and cobalt hydroxide precursor, Ni 1/3 Mn 1/3 Co 1/3 (OH) 2 , is investigated using a combination of in situ and ex situ techniques during the commonly-used coprecipitation process. These include in situ wide angle X-ray scattering, in-situ ultra-small angle X-ray scattering and ex situ particle size analysis. The growth rate of crystalline Ni 1/3 Mn 1/3 Co 1/3 (OH) 2 primary particle is found to be almost constant, consistent with a mathematical analysis of process. The growth of the Ni 1/3 Mn 1/3 Co 1/3 (OH) 2 secondary particle and its particle size distribution revealed different growth stages for samples prepared at different pH. These techniques are complimented with scanning electron microscopy and electrochemical testing to track the morphology and performance of the hydroxide particle and the subsequent calcined LiNi 1/3 Mn 1/3 Co 1/3 O 2 cathode active material. This study presents insights into the synthesis process and provides a deeper understanding to aid in process optimization.

Cathode precursor↗