Search NASA⌕ Search

SEARCH · Search NASA

Results for “control electronics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80

Experimental Evaluation of Steady-State Control Properties of an Electron-Bombardment Ion Thrustor

Examined in this report are the experimental steady-state gains, or changes, in beam-current output with changes in thrustor inputs for a 10-centimeter-diameter electron-bombardment ion thrustor. A general leveling off of beam current as a function of an input variable was found at the upper range of each variable, At the design operating point, the filament-heating current exhibited the greatest sensitivity, or percentage beam-current output change for a percentage change in the input (2 to 4). Accelerator voltage showed the least effect (0.04) while discharge voltage, magnetic field, and neutral propellant flow exhibited about the same sensitivity (0.4 to 0.5). Some effects of nonlinearity are shown that may require consideration in the design of a closed-loop control system.

CONTROL↗

Electronic system for high power load control

Parallel current paths are divided into two groups, with control devices in the current paths of one group each having a current limiting resistor, and the control devices in the other group each having no limiting resistor, so that when the control devices of the second group are turned fully on, a short circuit is achieved by the arrangement of parallel current paths. Separate but coordinated control signals are provided to turn on the control devices of the first group and increase their conduction toward saturation as a function of control input, and when fully on, or shortly before, to turn on the control devices of the second group and increase their conduction toward saturation as a function of the control input as that input continues to increase. Electronic means may be used to generate signals. The system may be used for 1-V characteristic measurements of solar arrays as well as for other load control purposes.

Miller, E. L.↗

Measurements of the ionization efficiency of protons in methane

The amount of energy released by a nuclear recoil ionizing the atoms of the active volume of detection appears “quenched” compared to an electron of the same kinetic energy. This different behavior in ionization between electrons and nuclei is described by the Ionization Quenching Factor (IQF) and it plays a crucial role in direct dark matter searches. For low kinetic energies (below 50 keV ), IQF measurements deviate significantly from common models used for theoretical predictions and simulations. We report measurements of the IQF for proton, an appropriate target for searches of Dark Matter candidates with a mass of approximately 1 GeV , with kinetic energies in between 2 keV and 13 keV in 100 mbar of methane. We used the Comimac facility in order to produce the motion of nuclei and electrons of controlled kinetic energy in the active volume, and a NEWS-G SPC to measure the deposited energy. The Comimac electrons are used as a reference to calibrate the detector with 7 energy points. A detailed study of systematic effects led to the final results well fitted by IQF (E K )=E$^α_K$ / (β+E$^α_K$) with α=0.70±0.08 and β=1.32±0.17 . In agreement with some previous works in other gas mixtures, we measured less ionization energy than predicted from SRIM simulations, the difference reaching 33% at 2 keV .

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Reliability analysis of the F-8 digital fly-by-wire system

The F-8 Digital Fly-by-Wire (DFBW) flight test program intended to provide the technology for advanced control systems, giving aircraft enhanced performance and operational capability is addressed. A detailed analysis of the experimental system was performed to estimated the probabilities of two significant safety critical events: (1) loss of primary flight control function, causing reversion to the analog bypass system; and (2) loss of the aircraft due to failure of the electronic flight control system. The analysis covers appraisal of risks due to random equipment failure, generic faults in design of the system or its software, and induced failure due to external events. A unique diagrammatic technique was developed which details the combinatorial reliability equations for the entire system, promotes understanding of system failure characteristics, and identifies the most likely failure modes. The technique provides a systematic method of applying basic probability equations and is augmented by a computer program written in a modular fashion that duplicates the structure of these equations.

Brock, L. D.↗

Neuromorphic Learning From Noisy Data

Two reports present numerical study of performance of feedforward neural network trained by back-propagation algorithm in learning continuous-valued mappings from data corrupted by noise. Two types of noise considered: plant noise which affects dynamics of controlled process and data-processing noise, which occurs during analog processing and digital sampling of signals. Study performed with view toward use of neural networks as neurocontrollers to substitute for, or enhance, performances of human experts in controlling mechanical devices in presence of sensor and actuator noise and to enhance performances of more-conventional digital feedback electronic process controllers in noisy environments.

Merrill, Walter C.↗

Confinement in electron heated plasmas in Wendelstein 7-X and ASDEX Upgrade; the necessity to control turbulent transport

In electron (cyclotron) heated plasmas, in both ASDEX Upgrade (L-mode) and Wendelstein 7-X, clamping of the ion temperature occurs at $T_\mathrm{i}$ ~ 1.5 keV independent of magnetic configuration. The ions in such plasmas are heated through the energy exchange power as ${n}_{\mathrm{e}}^{2}({T}_{\mathrm{e}}-{T}_{\mathrm{i}})/{T}_{\mathrm{e}}^{3/2}$, which offers a broad ion heating profile, similar to that offered by alpha heating in future thermonuclear fusion reactors. However, the predominant electron heating may put an additional constraint on the ion heat transport, as the ratio $T_\mathrm{e}T_\mathrm{i}$ > 1 can exacerbates ITG/TEM core turbulence. Therefore, in practical terms the strongly 'stiff' core transport translates into Ti-clamping in electron heated plasmas. Due to this clamping, electron heated L-mode scenarios, with standard gas fueling, in either tokamaks or stellarators may struggle to reach high normalized ion temperature gradients required in a compact fusion reactor. The comparison shows that core heat transport in neoclassically optimized stellarators is driven by the same mechanisms as in tokamaks. The absence of a strong H-mode temperature edge pedestal in stellarators, sofar (which, like in tokamaks, could lift the clamped temperature-gradients in the core), puts a strong requirement on reliable and sustainable core turbulence suppression techniques in stellarators.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Controlling the Focus in Electron-Beam Welders

Detector using two whirling wires measures focus of beam in electronbeam welder. Multiple-wire beam-sampling method provides for simple nullmeter focus indication easily controlled by operator. Detector not only operates at high beam currents but eliminates need for oscilloscope.

Macfarlane, D. I.↗

EXPERIMENTAL VERIFICATION OF TRANSPARENT SPIN MODE IN RHIC

High electron and ion polarizations are some of the key design requirements of a future Electron Ion Collider (EIC). The transparent spin mode, a concept inspired by the figure 8 ring design of JLEIC, is a novel technique for preservation and control of electron and ion spin polarizations in a collider or storage ring. It makes the ring lattice "invisible" to the spin and allows for polarization control by small quasi-static magnetic fields with practically no effect on the beam’s orbital characteristics. It offers unique opportunities for polarization maintenance and control in Jefferson Lab’s JLEIC and in BNL’s eRHIC. The transparent spin mode has been demonstrated in simulations and we now plan to test it experimentally. We present a design of an experiment using a polarized proton beam stored in one of the RHIC rings. In the experiment, one of the RHIC rings is configured in the transparent spin mode by aligning the axes of its two Siberian snakes. The experiment goals, procedures, hardware requirements and expected results are presented.

Morozov, V.S.↗

Evolution of magnetism in the magnetic topological semimetal NdSb x Te 2–x+δ

Magnetic topological semimetals LnSbTe (Ln = Lanthanide) have attracted intensive attention because of the presence of interplay between magnetism, topological, and electron correlations depending on the choices of magnetic Ln elements. Recently, varying Sb-Te composition has been found to effectively control the electronic and magnetic states in LnSb x Te 2-x . Here, with this motivation, we report the evolution of magnetic properties with Sb-Te substitution in NdSb x Te 2-x+δ , (0 ≤ x ≤ 1). Our work reveals the interesting non-monotonic change in magnetic ordering temperature with varying composition stoichiometry. In addition, reducing the Sb content x drives the reorientation of moments from in-plane (ab-plane) to out-of-plane (c-axis) direction that results in the distinct magnetic structures for two end compounds NdTe 2 (x = 0) and NdSbTe (x = 1). Furthermore, the moment orientation in NdSb x Te 2-x+δ is also found to be strongly tunable upon application of weak magnetic field, leading to rich magnetic phases depending on the composition stoichiometry, temperature, and magnetic field. Such strong tuning of magnetism in this material establishes it as a promising platform for investigating tunable topological states and correlated topological physics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Runaway Geneeration In Disruptions Of Plasmas In TFTR

Many disruptions in the Tokamak Fusion Test Reactor (TFTR) [D. Meade and the TFTR Group, in Proceedings of the International Conference on Plasma Physics and Controlled Nuclear Fusion, Washington, DC, 1990 (International Atomic Energy Agency, Vienna, 1991), Vol. 1, pp. 9-24] produced populations of runaway electrons which carried a significant fraction of the original plasma current. In this paper, we describe experiments where, following a disruption of a low-beta, reversed shear plasma, currents of up to 1 MA carried mainly by runaway electrons were controlled and then ramped down to near zero using the ohmic transformer. In the longer lasting runaway plasmas, Parail-Pogutse instabilities were observed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Transient behavior of a supersonic three-dimensional micronozzle with an intersecting capillary

An analysis of the interaction between a pulsed, supersonic microjet and an intersecting gas-filled capillary is presented, which enables a direct measurement of the pressure evolution inside the nozzle of the microjet. Plasma-emission spectroscopy was used to resolve, on a sub-microsecond timescale, the build-up and decay of pressure in the nozzle, which are shown to be correlated to the volume of the plenum supplying the nozzle and to the nozzle-throat size, respectively. The microjet, which was integrated with a capillary-discharge waveguide in a sapphire structure, was used to create a small, tunable region of high density gas within a centimeter-scale plateau of lower-density for use in a laser-plasma accelerator. The resultant longitudinally structured gas-density profile has been used to provide control of electron trapping and acceleration, but its evolution has not previously been directly quantified. Overall, the results presented here pave the way for improved control of laser-plasma accelerators and are also relevant to applications such as miniature satellites and lab-on-a-chip where precise knowledge of microjet pressure evolution is critical.

47 OTHER INSTRUMENTATION↗

A hybrid optoelectronic Mott insulator

The coupling of electronic degrees of freedom in materials to create “hybridized functionalities” is a holy grail of modern condensed matter physics that may produce versatile mechanisms of control. Correlated electron systems often exhibit coupled degrees of freedom with a high degree of tunability which sometimes lead to hybridized functionalities based on external stimuli. However, the mechanisms of tunability and the sensitivity to external stimuli are determined by intrinsic material properties which are not always controllable. A Mott metal-insulator transition (MIT) is technologically attractive due to the large changes in resistance, tunable by doping, strain, electric fields, and orbital occupancy but not, in and of itself, controllable with light. Here, an alternate approach is presented to produce optical functionalities using a properly engineered photoconductor/strongly correlated hybrid heterostructure. This approach combines a photoconductor, which does not exhibit an MIT, with a strongly correlated oxide, which is not photoconducting. Due to the intimate proximity between the two materials, the heterostructure exhibits giant volatile and nonvolatile, photoinduced resistivity changes with substantial shifts in the MIT transition temperatures. This approach can be extended to other judicious combinations of strongly correlated materials.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Topological materials by molecular beam epitaxy

Topology appears across condensed matter physics to describe a wide array of phenomena which could alter, augment, or fundamentally change the functionality of many technologies. Linking the basic science of topological materials to applications requires producing high-quality thin films. This will enable combining dissimilar materials while utilizing dimensionality, symmetry, and strain to create or control the electronic phase, as well as platforms to fabricate novel devices. Yet, one of the longstanding challenges in the field remains understanding and controlling the basic material properties of epitaxial thin films. Here, we discuss how understanding the fundamental properties of topological materials grown by molecular beam epitaxy (MBE) is key to deepening the knowledge of the basic physics, while developing a new generation of topological devices. A focus will be on the MBE growth of intrinsic materials, creation, and control of superconducting and magnetic topological phases. Addressing these questions in the coming decade will undoubtedly uncover many surprises as new materials are discovered and their growth as high-quality thin films is refined.

2d quantum materials↗

Actinides and Correlated Electron Materials

The Actinides and Correlated Electron Materials area of leadership spans Los Alamos National Laboratory competency in actinide materials research dating to the Manhattan Project as articulated in the Integrated Plutonium Science and Research Strategy and competency in strongly correlated electron systems dating back to at least the early 1980s. This area of leadership focuses on the goals of discovering, understanding, and controlling emergent electronic states and predictive performance of actinide materials. They are quintessentially linked by the fact that the physics of actinides—and plutonium in particular—are governed by strong electronic correlations. Not only is the electronic structure of actinides dictated by fine details of electron correlations, but chemical bonding and physical structure are as well. Hence, by addressing the first goal of this leadership area we can significantly accelerate progress on the second goal. To understand such matter requires probing the intertwined spin, charge, orbital, and lattice degrees of freedom with greater precision and developing models that accurately predict the consequences of these coupled degrees of freedom, on multiple length and time scales and including acute reactivity and effects of self-irradiation phenomena in these materials.

36 MATERIALS SCIENCE↗

Actinides and Correlated Electron Materials

The Actinides and Correlated Electron Materials area of leadership spans Los Alamos National Laboratory competency in actinide materials research dating to the Manhattan Project as articulated in the Integrated Plutonium Science and Research Strategy and competency in strongly correlated electron systems dating back to at least the early 1980s. This area of leadership focuses on the goals of discovering, understanding, and controlling emergent electronic states and predictive performance of actinide materials. They are quintessentially linked by the fact that the physics of actinides—and plutonium in particular—are governed by strong electronic correlations. Not only is the electronic structure of actinides dictated by fine details of electron correlations, but chemical bonding and physical structure are as well. Hence, by addressing the first goal of this leadership area we can significantly accelerate progress on the second goal. To understand such matter requires probing the intertwined spin, charge, orbital, and lattice degrees of freedom with greater precision and developing models that accurately predict the consequences of these coupled degrees of freedom, on multiple length and time scales and including acute reactivity and effects of self-irradiation phenomena in these materials.

36 MATERIALS SCIENCE↗

Microprocessor controlled proof-mass actuator

The objective of the microprocessor controlled proof-mass actuator is to develop the capability to mount a small programmable device on laboratory models. This capability will allow research in the active control of flexible structures. The approach in developing the actuator will be to mount all components as a single unit. All sensors, electronic and control devices will be mounted with the actuator. The goal for the force output capability of the actuator will be one pound force. The programmable force actuator developed has approximately a one pound force capability over the usable frequency range, which is above 2 Hz.

Horner, Garnett C.↗

Observation and Control of Unidirectional Ballistic Dynamics of Nanoparticles at a Liquid–Gas Interface by 4D Electron Microscopy

Understanding and controlling the dynamics of active Brownian objects far from equilibrium are fundamentally important for emerging technologies such as artificial micro/nanomotors for drug deliveries and noninvasive microsurgery. However, direct observation and control of unidirectional propulsion of individual nanoscale objects are technically challenging due to the required spatiotemporal resolution. Here, we report in situ visualization and manipulation of unidirectional superfast ballistic dynamics of a single-photon-activated gold nanoparticle (NP) along the liquid–gas interface by four-dimensional electron microscopy (4D EM) at nanometer and nanosecond scales. We observed that, upon repetitive femtosecond laser excitation, the NP at the liquid–gas interface exhibits a continuously superfast unidirectional translation with a linear dependence of its root mean squared velocity (νrms) on either the laser fluence or repetition rate. Under a single femtosecond pulse excitation, the NP exhibits a superfast ballistic translation at the nanosecond time scale. Combined experiment and physical modeling reveals that the superfast unidirectional, ballistic translation is driven by unidirectional random impulsive forces arising from the nanobubbles (NBs) induced by enhanced laser heating as a result of plasmonic excitation, which is controllable by tuning the laser characteristics. Furthermore, this directional plasmonic NB-propulsion mechanism sheds light on the design of light-controllable artificially intelligent micro/nanomotor systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗