Search NASA⌕ Search

SEARCH · Search NASA

Results for “data parallel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80

Measuring Ada as a software development technology in the Software Engineering Laboratory (SEL)

An experiment is in progress to measure the effectiveness of Ada in the National Aeronautics and Space Administration/Goddard Space Flight Center flight dynamics software development environment. The experiment features the parallel development of software in FORTRAN and Ada. The experiment organization, objectives, and status are discussed. Experiences with an Ada training program and data from the development of a 5700-line Ada training exercise are reported.

Agresti, W. W.↗

Detection of rotating thunderstorms using satellite imagery

In the case of the Carolina tornadoes, researchers prepared visible and IR GOES imagery covering the period 2000 Z when the storm entered South Carolina from Georgia until it exited North Carolina at 0200 Z into Virginia. The GOES IR imagery clearly demonstrated that this storm was imbedded in a continuously propagating mesolow with a well defined cold dome. The ground damage track paralleled exactly with the cold dome throughout the storm's life across the Carolinas. There were no advanced very high resolution radiometer (AVHRR) data during the period to allow researchers to inspect the cloud top for warm temperature anomalies. The Carolina storm did exhibit rightward deviating outflow which was oriented about 60 degrees to the 300 mb streamlines. The tornadoes of April 27, 1984 were part of a tornado producing cold front which stretched from Oklahoma to Minnesota. As the front moved eastward it touched off numerous tornadoes in eastern Wisconsin. GOES imagery for this data was prepared and it was strikingly clear that all along the North-South oriented squall line, the individual tunderstorms had cirrus plumes which had remarkable right deviation to the upper air flow. Unlike the Carolina long track supercell cell-mesolow system, these storms were isolated individual thunderstorms which touched off at least 16 tornadoes in eastern Wisconsin stretching from the Milwaukee area on the south to Vilas County in the north. The monster tornado of June 8, 1984 which leveled 90 percent of the village of Barneveld, Wisconsin and killed 9 persons is also discussed.

Anderson, C. E.↗

Simulation of an array-based neural net model

Research in cognitive science suggests that much of cognition involves the rapid manipulation of complex data structures. However, it is very unclear how this could be realized in neural networks or connectionist systems. A core question is: how could the interconnectivity of items in an abstract-level data structure be neurally encoded? The answer appeals mainly to positional relationships between activity patterns within neural arrays, rather than directly to neural connections in the traditional way. The new method was initially devised to account for abstract symbolic data structures, but it also supports cognitively useful spatial analogue, image-like representations. As the neural model is based on massive, uniform, parallel computations over 2D arrays, the massively parallel processor is a convenient tool for simulation work, although there are complications in using the machine to the fullest advantage. An MPP Pascal simulation program for a small pilot version of the model is running.

Barnden, John A.↗

Ion specific differences in energetic field aligned upflowing ions at 1 earth radius

An ion-upflow event over the northern auroral zone during a small magnetic storm on August 24, 1976 is characterized on the basis of S3-3 satellite ion-mass-spectrometer observations at 0.5-16 keV. The data are presented in tables, graphs, and diagrams and analyzed in detail. The distributions of upward-flowing O(+) and H(+) associated with parallel electric fields below the satellite are shown to have transverse temperatures of about 1 keV and 0.1 keV, respectively, while the corresponding parallel temperatures were about 1 keV and 0.6 keV; the average energy of the O(+) ions is found to be 2-3 times greater than that of the H(+) ions in the acceleration regions. Possible interpretations of these findings are discussed.

Ghielmetti, A. G.↗

Report from ionospheric science

The general strategy to advance knowledge of the ionospheric component of the solar terrestrial system should consist of a three pronged attack on the problem. Ionospheric models should be refined by utilization of existing and new data bases. The data generated in the future should emphasize spatial and temporal gradients and their relation to other events in the solar terrestrial system. In parallel with the improvement in modeling, it will be necessary to initiate a program of advanced instrument development. In particular, emphasis should be placed on the area of improved imaging techniques. The third general activity to be supported should be active experiments related to a better understanding of the basic physics of interactions occurring in the ionospheric environment. These strategies are briefly discussed.

Raitt, W. J.↗

Frequency domain model for analysis of paralleled, series-output-connected Mapham inverters

The Mapham resonant inverter is characterized as a two-port network driven by a selected periodic voltage. The two-port model is then used to model a pair of Mapham inverters connected in series and employing phasor voltage regulation. It is shown that the model is useful for predicting power output in paralleled inverter units, and for predicting harmonic current output of inverter pairs, using standard power flow techniques. Some sample results are compared to data obtained from testing hardware inverters.

Brush, Andrew S.↗

Multiphase complete exchange on a circuit switched hypercube

On a distributed memory parallel computer, the complete exchange (all-to-all personalized) communication pattern requires each of n processors to send a different block of data to each of the remaining n - 1 processors. This pattern is at the heart of many important algorithms, most notably the matrix transpose. For a circuit switched hypercube of dimension d(n = 2(sup d)), two algorithms for achieving complete exchange are known. These are (1) the Standard Exchange approach that employs d transmissions of size 2(sup d-1) blocks each and is useful for small block sizes, and (2) the Optimal Circuit Switched algorithm that employs 2(sup d) - 1 transmissions of 1 block each and is best for large block sizes. A unified multiphase algorithm is described that includes these two algorithms as special cases. The complete exchange on a hypercube of dimension d and block size m is achieved by carrying out k partial exchange on subcubes of dimension d(sub i) Sigma(sup k)(sub i=1) d(sub i) = d and effective block size m(sub i) = m2(sup d-di). When k = d and all d(sub i) = 1, this corresponds to algorithm (1) above. For the case of k = 1 and d(sub i) = d, this becomes the circuit switched algorithm (2). Changing the subcube dimensions d, varies the effective block size and permits a compromise between the data permutation and block transmission overhead of (1) and the startup overhead of (2). For a hypercube of dimension d, the number of possible combinations of subcubes is p(d), the number of partitions of the integer d. This is an exponential but very slowly growing function and it is feasible over these partitions to discover the best combination for a given message size. The approach was analyzed for, and implemented on, the Intel iPSC-860 circuit switched hypercube. Measurements show good agreement with predictions and demonstrate that the multiphase approach can substantially improve performance for block sizes in the 0 to 160 byte range. This range, which corresponds to 0 to 40 floating point numbers per processor, is commonly encountered in practical numeric applications. The multiphase technique is applicable to all circuit-switched hypercubes that use the common e-cube routing strategy.

Bokhari, Shahid H.↗

Implementation of a blade element UH-60 helicopter simulation on a parallel computer architecture in real-time

A high-performance platform for development of real-time helicopter flight simulations based on a simulation development and analysis platform combining a parallel simulation development and analysis environment with a scalable multiprocessor computer system is described. Simulation functional decomposition is covered, including the sequencing and data dependency of simulation modules and simulation functional mapping to multiple processors. The multiprocessor-based implementation of a blade-element simulation of the UH-60 helicopter is presented, and a prototype developed for a TC2000 computer is generalized in order to arrive at a portable multiprocessor software architecture. It is pointed out that the proposed approach coupled with a pilot's station creates a setting in which simulation engineers, computer scientists, and pilots can work together in the design and evaluation of advanced real-time helicopter simulations.

Moxon, Bruce C.↗

Electron time dispersion

Observations of electrons during a sounding rocket flight from Sondrestromfjord, Greenland, in 1985 showed numerous instances of electron time-of-flight dispersion, that is, a coherent structure in which fast electrons arrived before slow electrons. The instrumentation measured many pitch angles simultaneously with high time resolution, providing a detailed view of the temporal evolution of the electron signature at rocket altitudes which was indicative of an impulsive injection of electrons over a range of energies. A model utilizing an extended, quasi-static (static on a timescale of 1 s), parallel electric field was developed to investigate a possible mechanism for the injection of these electrons. The model is found to fit the data well only when a background is added which cannot be self-consistently generated by the model, although other parameters used in the model are in general agreement with previous reports. This leads to the conclusion that electron dispersion is more probably generated by a wave acceleration mechanism.

Kletzing, C. A.↗

Observations of mirror waves and plasma depletion layer upstream of Saturn's magnetopause

The two inbound traversals of the Saturn's magnetosheath by Voyagers 1 and 2 have been studied using plasma and magnetic field data. In a great portion of the subsolar magnetosheath, large-amplitude compressional waves are observed at low frequency (approximately 0.1 f(sub p)) in a high-beta plasma regime. The fluctuations of the magnetic field magnitude and ion density are anticorrelated, as are those of the magnetic and thermal pressures. The normals to the structures are almost orthogonal to the background field, and the Doppler ratio is on the average small. Even though the data do not allow the determination of the ion thermal anisotropy, the observations are consistent with values of T(sub perpendicular)/T(sub parallel) greater than 1, producing the onset of the mirror instability. All the above features indicate that the waves should be most probably identified with mirror modes. One of the two magnetopause crossings is of the high-shear type and the above described waves are seen until the magnetopause. The other crossing is of the low-shear type and, similarly to what has been observed at Earth, a plasma depletion occurs close to the magnetopause. In this layer, waves with smaller amplitude, presumably of the mirror mode, are present together with higher-frequency waves showing a transverse component.

Violante, L.↗

Wide Temperature Magnetization Characteristics of Transverse Magnetically Annealed Amorphous Tapes for High Frequency Aerospace Magnetics

100 kHz magnetization properties of sample transverse magnetically annealed, cobalt-based amorphous and iron-based nanocrystalline tape wound magnetic cores are presented over the temperature range of -150 C to 150 C, at selected values of B(sub peak). Frequency resolved characteristics are given over the range of 50 kHz to 1 MHz, but at B(sub peak) = 0.1 T and 50 C only. Basic exciting winding current and induced voltage data were taken on bare toroidal cores, in a standard type measurement setup. A linear permeability model, which represents the core by a parallel L-R circuit, is used to interpret and present the magnetization characteristics and several figures of merit applicable to inductor materials are reviewed. The 100 kHz permeability thus derived decreases with increasing temperature for the Fe-based, nanocrystalline material, but increases roughly linearly with temperature for the two Co-based materials, as long as B(sub peak) is sufficiently low to avoid saturation effects. Due to the high permeabilities, rather low values of the 'quality factor' Q, from about 20 to below unity, were obtained over the frequency range of 50 kHz to 1 MHz (50 C, B(sub peak) = 0.1 T). Therefore these cores must be gapped in order to make up high Q or high current inductors. However, being rugged, low core loss materials with flat B-H loop characteristics, they may provide new solutions to specialty inductor applications.

Niedra, Janis M.↗

The Severe Weather Outbreak of 10 November 2002: Lightning and Radar Analysis of Storms in the Deep South

On the afternoon and evening of 10 November 2002, the Midwest and Deep South were struck by a major outbreak of severe storms that produced some 80 tornadoes. In terms of number of tornadoes, this was the largest outbreak in the United States since November 1992. Some 32 of the tornadoes occurred in Tennessee, Mississippi, Alabama and Georgia, including several long-track killers. We use the North Alabama Lightning Mapping Array (LMA) and other data sources to perform a comprehensive analysis of the structure and evolution of the outbreak. Most of the Southern tornadoes occurred in isolated, fast-moving supercell storms that formed in warm, moist air ahead of a major cold front. Storms tended to form in lines parallel to storm cell motion, resulting in many communities being hit multiple times by severe storms that evening. Supercells in Tennessee produced numerous strong tornadoes with short to medium-length track paths, while the supercells further south produced several very long-track tornadoes. Radar data indicate that the Tennessee storms tended to split frequently, apparently limiting their ability to sustain long-lived tornadoes, while storms further south split at most one time. The differences between these storms appear to be related to the presence of stronger jetstream winds in Tennessee relative to those present in Mississippi, Alabama and Georgia. LMA-derived flash rates associated with most of the supercell storm cores were about 1-2 flashes per second. Rapid increases in lightning rates (or "jumps") occurred prior to tornado touchdown in many instances. Lightning "holes" (lightning-free regions associated with the echo-free vault) occurred in two of the Tennessee supercells. The complexity of the relationship between lightning and storm severity is revealed by the behavior of one Alabama supercell, which produced a peak flash rate of nearly 14 flashes per second, well after the end of its long-track tornado, while interacting and ultimately merging with a daughter supercell on its southwest flank. Close examination of this powerful storm indicates that its prodigious flash rate was the result of strong flash activity over an unusually large area, rather than a concentrated core of extremely high flash rate activity.

Buechler, D. E.↗

Evaluation of the Impact of Atmospheric Infrared Sounder (AIRS) Radiance and Profile Data Assimilation in Partly Cloudy Regions

Improvements to global and regional numerical weather prediction have been demonstrated through assimilation of data from NASA s Atmospheric Infrared Sounder (AIRS). Current operational data assimilation systems use AIRS radiances, but impact on regional forecasts has been much smaller than for global forecasts. Retrieved profiles from AIRS contain much of the information that is contained in the radiances and may be able to reveal reasons for this reduced impact. Assimilating AIRS retrieved profiles in an identical analysis configuration to the radiances, tracking the quantity and quality of the assimilated data in each technique, and examining analysis increments and forecast impact from each data type can yield clues as to the reasons for the reduced impact. By doing this with regional scale models individual synoptic features (and the impact of AIRS on these features) can be more easily tracked. This project examines the assimilation of hyperspectral sounder data used in operational numerical weather prediction by comparing operational techniques used for AIRS radiances and research techniques used for AIRS retrieved profiles. Parallel versions of a configuration of the Weather Research and Forecasting (WRF) model with Gridpoint Statistical Interpolation (GSI) are run to examine the impact AIRS radiances and retrieved profiles. Statistical evaluation of 6 weeks of forecast runs will be compared along with preliminary results of in-depth investigations for select case comparing the analysis increments in partly cloudy regions and short-term forecast impacts.

Zavodsky, Bradley↗

Evaluation of the Impact of AIRS Radiance and Profile Data Assimilation in Partly Cloudy Regions

Improvements to global and regional numerical weather prediction have been demonstrated through assimilation of data from NASA s Atmospheric Infrared Sounder (AIRS). Current operational data assimilation systems use AIRS radiances, but impact on regional forecasts has been much smaller than for global forecasts. Retrieved profiles from AIRS contain much of the information that is contained in the radiances and may be able to reveal reasons for this reduced impact. Assimilating AIRS retrieved profiles in an identical analysis configuration to the radiances, tracking the quantity and quality of the assimilated data in each technique, and examining analysis increments and forecast impact from each data type can yield clues as to the reasons for the reduced impact. By doing this with regional scale models individual synoptic features (and the impact of AIRS on these features) can be more easily tracked. This project examines the assimilation of hyperspectral sounder data used in operational numerical weather prediction by comparing operational techniques used for AIRS radiances and research techniques used for AIRS retrieved profiles. Parallel versions of a configuration of the Weather Research and Forecasting (WRF) model with Gridpoint Statistical Interpolation (GSI) are run to examine the impact AIRS radiances and retrieved profiles. Statistical evaluation of a long-term series of forecast runs will be compared along with preliminary results of in-depth investigations for select case comparing the analysis increments in partly cloudy regions and short-term forecast impacts.

Zavodsky, Bradley↗

Planetary Exploration Reinvented

During the past 50 years, we have learned to explore and work in space. Much of what we know about the Solar System we owe to observations and sampling made by robotic spacecraft, landers, planetary rovers, and astronauts. As we look to the future, however, there is ample opportunity to reinvent planetary exploration: to develop new techniques and systems that will enhance and enable discovery.In this talk, I will describe how the NASA Ames Intelligent Robotics Group (IRG) is working to reinvent planetary exploration. First, I will present IRG's development of robots for human exploration. These robots are designed to perform work before, in parallel, and after human activity. Next, I will show how IRG is building automated planetary mapping systems to process the enormous amount of data that NASA collects from orbit. Finally, I will discuss how IRG is changing the way ground control software is created, particularly for supporting science operations.

robotics↗

Processing CCD Images to Detect Transits of Earth-Sized Planets: Maximizing Sensitivity While Achieving Reasonable Downlink Requirements

We have performed end-to-end laboratory and numerical simulations to demonstrate the capability of differential photometry under realistic operating conditions to detect transits of Earth-sized planets orbiting solar-like stars. Data acquisition and processing were conducted using the same methods planned for the proposed Kepler Mission. These included performing aperture photometry on large-format CCD images of an artificial star fields obtained without a shutter at a readout rate of 1 megapixel/sec, detecting and removing cosmic rays from individual exposures and making the necessary corrections for nonlinearity and shutterless operation in the absence of darks. We will discuss the image processing tasks performed `on-board' the simulated spacecraft, which yielded raw photometry and ancillary data used to monitor and correct for systematic effects, and the data processing and analysis tasks conducted to obtain lightcurves from the raw data and characterize the detectability of transits. The laboratory results are discussed along with the results of a numerical simulation carried out in parallel with the laboratory simulation. These two simulations demonstrate that a system-level differential photometric precision of 10-5 on five- hour intervals can be achieved under realistic conditions.

Earth-size planets↗

Impact of Magnetic Draping, Convection, and Field Line Tying on Magnetopause Reconnection Under Northward IMF

We simulate a northward IMF cusp reconnection event at the magnetopause using the OpenGGCM resistive MHD code. The ACE input data, solar wind parameters, and dipole tilt belong to a 2002 reconnection event observed by IMAGE and Cluster. Based on a fully three-dimensional skeleton separators, nulls, and parallel electric fields, we show magnetic draping, convection, ionospheric field line tying play a role in producing a series of locally reconnecting nulls with flux ropes. The flux ropes in the cusp along the global separator line of symmetry. In 2D projection, the flux ropes the appearance of a tearing mode with a series of 'x's' and 'o's' but bearing a kind of 'guide field' that exists only within the magnetopause. The reconnecting field lines in the string of ropes involve IMF and both open and closed Earth magnetic field lines. The observed magnetic geometry reproduces the findings of a superposed epoch impact parameter study derived from the Cluster magnetometer data for the same event. The observed geometry has repercussions for spacecraft observations of cusp reconnection and for the imposed boundary conditions reconnection simulations.

Wendel, Deirdre E.↗

Using SpF to Achieve Petascale for Legacy Pseudospectral Applications

Pseudospectral (PS) methods possess a number of characteristics (e.g., efficiency, accuracy, natural boundary conditions) that are extremely desirable for dynamo models. Unfortunately, dynamo models based upon PS methods face a number of daunting challenges, which include exposing additional parallelism, leveraging hardware accelerators, exploiting hybrid parallelism, and improving the scalability of global memory transposes. Although these issues are a concern for most models, solutions for PS methods tend to require far more pervasive changes to underlying data and control structures. Further, improvements in performance in one model are difficult to transfer to other models, resulting in significant duplication of effort across the research community. We have developed an extensible software framework for pseudospectral methods called SpF that is intended to enable extreme scalability and optimal performance. Highlevel abstractions provided by SpF unburden applications of the responsibility of managing domain decomposition and load balance while reducing the changes in code required to adapt to new computing architectures. The key design concept in SpF is that each phase of the numerical calculation is partitioned into disjoint numerical kernels that can be performed entirely inprocessor. The granularity of domain decomposition provided by SpF is only constrained by the datalocality requirements of these kernels. SpF builds on top of optimized vendor libraries for common numerical operations such as transforms, matrix solvers, etc., but can also be configured to use open source alternatives for portability. SpF includes several alternative schemes for global data redistribution and is expected to serve as an ideal testbed for further research into optimal approaches for different network architectures. In this presentation, we will describe our experience in porting legacy pseudospectral models, MoSST and DYNAMO, to use SpF as well as present preliminary performance results provided by the improved scalability.

DYNAMO↗