Search NASA⌕ Search

SEARCH · Search NASA

Results for “high modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80

Influence of High Cycle Thermal Loads on Thermal Fatigue Behavior of Thick Thermal Barrier Coatings

Thick thermal barrier coating systems in a diesel engine experience severe thermal Low Cycle Fatigue (LCF) and High Cycle Fatigue (HCF) during engine operation. In the present study, the mechanisms of fatigue crack initiation and propagation, as well as of coating failure, under thermal loads which simulate engine conditions, are investigated using a high power CO2 laser. In general, surface vertical cracks initiate early and grow continuously under LCF and HCF cyclic stresses. It is found that in the absence of interfacial oxidation, the failure associated with LCF is closely related to coating sintering and creep at high temperatures, which induce tensile stresses in the coating after cooling. Experiments show that the HCF cycles are very damaging to the coating systems. The combined LCF and HCF tests produced more severe coating surface cracking, microspallation and accelerated crack growth, as compared to the pure LCF test. It is suggested that the HCF component cannot only accelerate the surface crack initiation, but also interact with the LCF by contributing to the crack growth at high temperatures. The increased LCF stress intensity at the crack tip due to the HCF component enhances the subsequent LCF crack growth. Conversely, since a faster HCF crack growth rate will be expected with lower effective compressive stresses in the coating, the LCF cycles also facilitate the HCF crack growth at high temperatures by stress relaxation process. A surface wedging model has been proposed to account for the HCF crack growth in the coating system. This mechanism predicts that HCF damage effect increases with increasing temperature swing, the thermal expansion coefficient and the elastic modulus of the ceramic coating, as well as the HCF interacting depth. A good agreement has been found between the analysis and experimental evidence.

Zhu, Dongming↗

Mechanical Behavior and Analytical Modeling of Melt-Infiltrated SiC/SiC Woven Composite

The desirable properties in ceramic matrix composites (CMCs), such as high temperature strength, corrosion resistance, high toughness, low density, or good creep resistance have led to increased use of CMCs in high-speed engine structural components and structures that operate in extreme temperature and hostile aero-thermo-chemical environments. Ceramic matrix composites have been chosen for turbine material in the design of 21st century civil propulsion systems to achieve high fuel economy, improved reliability, extended life, and reduced cost. Most commercial CMCs are manufactured using a chemical vapor infiltration (CVI) process. However, a lower cost fabrication known as melt-infiltration process is also providing CMCs marked for use in hot sections of high-speed civil transports. Limited samples of a SiC/SiC melt-infiltrated woven composites are being investigated at room and elevated temperature below and above matrix cracking. These samples show graceful failure and toughness at room temperature with a reduction in strength and modulus at elevated temperatures. A generic finite element model is also being developed to predict monotonic and cyclic loading behavior of the woven composite. Use of the initial test data from the woven composite is being used for the development of the analytical model. This model is the first of a iterative process leading towards the development the model's capability to predict behavior at room and elevated temperature for monotonic and cyclic loading. The purpose of this paper is to report on the material and mechanical findings of the SiC/SiC melt-infiltrated woven composite and progress on the development of the finite element model.

Lang, J.↗

Multiscale Modeling of Thermoplastics Using Atomistic-informed Micromechanics

A multiscale model was developed for predicting the thermoelastic behavior of semi-crystalline thermoplastic materials for composite aerospace applications. At the highest scale containing the semi-crystalline spherulite in an amorphous matrix, the generalized method of cells, or high fidelity method of cells, was used to perform the homogenization calculations to obtain the effective properties. Models were developed assuming a cubic, or spherical shape, for the spherulite to understand if the morphology of the spherulite affects the effective thermoelastic properties. The generalized method of cells was used to model at the repeating unit cells at the subscales of the microstructure including the lamellae stacks and granular crystal blocks. The scales are integrated using the multiscale micromechanics method in the NASA Multiscale Analysis Tool. Data from molecular dynamics simulations were used as inputs for the amorphous and crystalline constituents. Convergence studies were performed to determine the best level of discretization for the repeating unit cell at the highest scale. Effective Young’s modulus, shear modulus, Poisson’s ratio, coefficient of thermal expansion, and thermal conductivity were predicted for polyether ether ketone and polyether ketone ketone, and very good agreement between the model utilizing the cubic spherulite and the experimental data, where available, was observed for polyether ketone ketone. Normalization of the data for the bulk polyether ketone ketone, against amorphous data, improved the predictions as compared to experimental data. Overall, the high fidelity method of cells predicted a stiffer response then the generalized method of cells as the crystallinity was increased. The shape of the spherulite had a minimal effect on the predicted bulk properties of the polymers.

thermoplastics↗

Temperature dependence of creep compliance of highly cross-linked epoxy: A molecular simulation study

We have used molecular dynamics (MD) simulations to study the effect of temperature on the creep compliance of neat cross-linked epoxy. Experimental studies of mechanical behavior of cross-linked epoxy in literature commonly report creep compliance values, whereas molecular simulations of these systems have primarily focused on the Young’s modulus. In this work, in order to obtain a more direct comparison between experiments and simulations, atomistically detailed models of the cross-linked epoxy are used to study their creep compliance as a function of temperature using MD simulations. The creep tests are performed by applying a constant tensile stress and monitoring the resulting strain in the system. Our results show that simulated values of creep compliance increase with an increase in both time and temperature. We believe that such calculations of the creep compliance, along with the use of time temperature superposition, hold great promise in connecting the molecular insight obtained from molecular simulation at small length- and time-scales with the experimental behavior of such materials. To the best of our knowledge, this work is the first reported effort that investigates the creep compliance behavior of cross-linked epoxy using MD simulations.

36 MATERIALS SCIENCE↗

Compression behavior of lithium fluoride up to 80 GPa and 2300 K

Here, the high-temperature compression behavior of lithium fluoride (LiF) has been determined to ∼80 GPa and 2300 K by means of high-resolution synchrotron-based x-ray diffraction in a laser-heated diamond-anvil cell. The room-temperature Vinet equation of state (EOS) for LiF yields an isothermal room-temperature, ambient-pressure lattice parameter a 0 = 4.028 (±0.003) Å, volume V 0 = 65.35 (±0.03) Å 3 , bulk modulus K 0 = 67.57 (±0.34) GPa, and its pressure derivative K 0 ’ = 4.64 (±0.03). This expanded experimental dataset is in good agreement with the LiF thermal equation of state by Myint et al. (2019) up to ∼2300 K and 25 GPa. At higher pressures and temperatures our data shows reduced thermal expansion compared to the prediction and may be particularly important for experiments at more extreme conditions.

High-pressure behavior↗

Interlaminar shear test method development for long term durability testing of composites

The high speed civil transport is a commercial aircraft that is expected to carry 300 passengers at Mach 2.4 over a range of more than 6000 nautical miles. With the existing commercial structural material technology (i.e., aluminum) the performance characteristics of the high speed civil transport would not be realized. Therefore there has been a concerted effort in the development of light weight materials capable of withstanding elevated temperatures for long duration. Thermoplastic composite materials are such candidate materials and the understanding of how these materials perform over the long term under harsh environments is essential to safe and effective design. The matrix dominated properties of thermoplastic composites are most affected by both time and temperature. There is currently an effort to perform short term testing to predict long term behavior of in-plane mechanical properties E22 (transverse modulus of elasticity) and G12 (shear modulus). Out-of-plane properties such as E33, G13, and G23 are inherently more difficult to characterize. This is especially true for the out-of-plane shear modulus G23 and hence there is no existing acceptable standard test method. Since G23 is the most matrix dominated property, it is essential that a test method be developed. A shear test methodology is developed to do just that. The test method, called the double notched specimen, along with the previously developed shear gage was tested at room temperature. Mechanical testing confirmed the attributes of the methodology. A finite element parametric study was conducted for specimen optimization. Moire interferometry, a high sensitivity laser optical method, was used for full-field analysis of the specimen. From this work, material parameters will be determined and thus enable the prediction of long term material behavior of laminates subjected to general loading states.

Ifju, Peter G.↗

Anomalous elastic behavior of tantalum at high pressures: Experimental and theoretical studies

Elastic wave velocities of polycrystalline tantalum have been measured up to 13.6 GPa at room temperature using ultrasonic interferometry technique in a multi-anvil apparatus. The bulk and shear moduli, as well as their pressure derivatives are obtained using Eulerian 3rd order finite strain equations, yielding K S0 = 193.9(29) GPa, G 0 = 69.3(10) GPa, K S0' = 3.18(5) and G 0' = 0.88(1). Here the Steinberg-Guinan yield stress model is examined using the current shear modulus and its pressure derivative, where a slightly lower A 0 = 0.0127 GPa –1 compared to previous studies is obtained. First-principles calculations on the elasticity of tantalum have also been performed up to 200 GPa. Anomalous softening of the elastic shear constant C 44 and shear wave velocity V S is observed between 80– 180 GPa, whereas the anisotropy shows a softening-stiffening behavior with increasing pressure and reaches a minimum at around 150 GPa. Such anomalies might commonly originate from the nesting of Fermi surface for Group VB metals.

36 MATERIALS SCIENCE↗

High temperature annealing of irradiated nuclear grade graphite

Previous work has shown that the material properties of nuclear grade graphite are substantially affected by the atomic and microstructural changes that occur during neutron-irradiation. The parameters that play a role in these changes are irradiation dose, temperature, graphite composition and the initial microstructure of the graphite. Understanding the details of how these material changes occur and exactly what the changes consists of will enable the prediction of the material property changes as a function of these variables. Other work has shown these atomic level and microstructural changes can be healed or annealed out by raising the irradiated graphite above its irradiation temperature. Here in this work, experiments were carried out to investigate how the properties of irradiated graphite recover when heated. By showing property recovery as a function of annealing temperature or energy, insight is provided into the type of damage that occurred during neutron-irradiation. The data presented here shows recovery of thermal diffusivity, coefficient of thermal expansion, Young's modulus and electrical resistivity between annealing temperatures of 500 °C and 2380 °C. Graphite grades NBG-18, IG-110 and PCEA are considered that were both stressed and unstressed during irradiation.

36 MATERIALS SCIENCE↗

Correlating Macro and Atomic Structure with Elastic Properties and Ionic Transport of Glassy Li 2 S‐P 2 S 5 (LPS) Solid Electrolyte for Solid‐State Li Metal Batteries

Abstract A combination of high ionic conductivity and facile processing suggest that sulfide‐based materials are promising solid electrolytes that have the potential to enable Li metal batteries. Although the Li 2 S‐P 2 S 5 (LPS) family of compounds exhibit desirable characteristics, it is known that Li metal preferentially propagates through microstructural defects, such as particle boundaries and/or pores. Herein, it is demonstrated that a near theoretical density (98% relative density) LPS 75‐25 glassy electrolyte exhibiting high ionic conductivity can be achieved by optimizing the molding pressure and temperature. The optimal molding pressure reduces porosity and particle boundaries while preserving the preferred amorphous structure. Moreover, molecular rearrangements and favorable Li coordination environments for conduction are attained. Consequently, the Young's Modulus approximately doubles (30 GPa) and the ionic conductivity increases by a factor of five (1.1 mS cm −1 ) compared to conventional room temperature molding conditions. It is believed that this study can provide mechanistic insight into processing‐structure‐property relationships that can be used as a guide to tune microstructural defects/properties that have been identified to have an effect on the maximum charging current that a solid electrolyte can withstand during cycling without short‐circuiting.

Garcia‐Mendez, Regina↗

Microstructures, mechanical behavior and strengthening mechanism of TiSiCN nanocomposite films

Recently, the arguments have existed in the strengthening mechanism and microstructural model of the nanocomposite film due to lack of the convincible experimental evidences. In this investigation, the quarternary TiSiCN nanocomposite films with the different C and Si contents are synthesized by the reactive-magnetron-sputtering technique. The TiSiCN film is characterized as the nanocomposite structure with the TiN nanocrystallites surrounded by the (Si 3 N 4 + C + CN x ) interface phase. When the C/Si content ratio is 2:2, the TiSiCN nanocomposite film is remarkably strengthened with the maximal hardness and elastic modulus of 46.1 GPa and 425 GPa, respectively. Meanwhile, the (Si 3 N 4 + C + CN x ) interfaces exhibit as a crystallized form, which can coordinate the growth misorientations and maintain the coherently epitaxial growth between the TiN nanocrystallites and interfaces. Through the high-resolution transmission electron microscopy (HRTEM) observations, this investigation firstly provides the direct experimental evidence for the crystallized feature of the interfaces when the TiSiCN nanocomposite film is strengthened, suggesting that the strengthening effect of the TiSiCN nanocomposite film can be attributed to the coherent-interface strengthening mechanism, which is expressed as the “nc-TiN/c-Si 3 N 4 /c-C/c-CN x ” model.

36 MATERIALS SCIENCE↗

Thermal conductivity of Glycerol’s liquid, glass, and crystal states, glass-liquid-glass transition, and crystallization at high pressures

To investigate the effects of local density fluctuations on phonon propagation in a hydrogen bonded structure, we studied the thermal conductivity κ of the crystal, liquid, and glassy states of pure glycerol as a function of the temperature, T, and the pressure, p. We find that the following: (i) κ{sub crystal} is 3.6-times the κ{sub liquid} value at 140 K at 0.1 MPa and 2.2-times at 290 K, and it varies with T according to 138 × T{sup −0.95}; (ii) the ratio κ{sub liquid} (p)/κ{sub liquid} (0.1 MPa) is 1.45 GPa{sup −1} at 280 K, which, unexpectedly, is about the same as κ{sub crystal} (p)/κ{sub crystal} (0.1 MPa) of 1.42 GPa{sup −1} at 298 K; (iii) κ{sub glass} is relatively insensitive to T but sensitive to the applied p (1.38 GPa{sup −1} at 150 K); (iv) κ{sub glass}-T plots show an enhanced, pressure-dependent peak-like feature, which is due to the glass to liquid transition on heating; (v) continuous heating cold-crystallizes ultraviscous glycerol under pressure, at a higher T when p is high; and (vi) glycerol formed by cooling at a high p and then measured at a low p has a significantly higher κ than the glass formed by cooling at a low p. On heating at a fixed low p, its κ decreases before its glass-liquid transition range at that p is reached. We attribute this effect to thermally assisted loss of the configurational and vibrational instabilities of a glass formed at high p and recovered at low p, which is different from the usual glass-aging effect. While the heat capacity, entropy, and volume of glycerol crystal are less than those for its glass and liquid, κ{sub crystal} of glycerol, like its elastic modulus and refractive index, is higher. We discuss these findings in terms of the role of fluctuations in local density and structure, and the relations between κ and the thermodynamic quantities.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Rayleigh-Taylor-instability experiments with elastic-plastic materials

A rotating wheel experimental facility was developed to investigate incompressible Rayleigh-Taylor instability in elastic-plastic materials. A soft solid (mayonnaise) was chosen as the elastic-plastic material for experiments; material properties that include shear modulus and yield strength were fully characterized using a vane spindle type rheometer. Initial perturbations of varying amplitudes and wavelengths were generated on the interface of the soft solid using sinusoidal cutting guides. A backlit imaging technique was used in conjunction with a high-speed camera to track the motion of the interface at various phases of the instability. Results for both two- and three-dimensional perturbations were compared to study the acceleration required for instability and the growth after the interface yielded. Exponential growth rates were observed after instability was reached with trends of increasing growth rates for lower initial amplitudes. It was found that the acceleration required for instability increased when initial amplitude and wavelength decreased. Here, three-dimensional interfaces were found to be more stable. For both cases, a decrease in initial amplitude produced a more stable interface that increased the threshold acceleration required for the instability. Critical amplitude conditions for instability were calculated and compared with various analytical models and other experimental results.

42 ENGINEERING↗

Computational fluid mechanics utilizing the variational principle of modeling damping seals

A computational fluid dynamics code for application to traditional incompressible flow problems has been developed. The method is actually a slight compressibility approach which takes advantage of the bulk modulus and finite sound speed of all real fluids. The finite element numerical analog uses a dynamic differencing scheme based, in part, on a variational principle for computational fluid dynamics. The code was developed in order to study the feasibility of damping seals for high speed turbomachinery. Preliminary seal analyses have been performed.

Abernathy, J. M.↗

BioPuSL: Material & Process Optimization

Stereolithography is an advantages bioprinting technique that can be used to develop 3 dimensional printed structures. In the field, prints of structures with cells seeded after the printing process has completed has shown to generate high cell viability [ Hang Lin]. Currently, a technique is needed to print with cells already in the resin so that the cells print inside the structures as the layers are curing. For this to occur, the resin and the parameters of the printing process need to print high-resolution structures while still able to achieve high cell viability. This technique can have significant impact many biological fields like tissue and drug application studies. In this study, various concentrations of Poly (ethylene glycol) diacrylate (PEGDa) and Gelatin Methacryloyl (GelMA) are used as prepolymers with the photoinitiator Lithium phenyl- 2,4,6-trimethylbenzoylphosphinate (LAP) at 1% weight concentration is used in the resin. The mechanical properties, biocompatibility, and impacts of the parameters are tested. From this study we were able to conclude that the amount of PEGDa makes a significant impact on storage modulus of the gel. Likewise, the various amounts of PEGDa, when printing, will affect the amount of polymerization that occurs. Therefore, if less than the needed amount of PEGDa is used when printing, the 3D structure will not fully form or form at all. Also, when studying various GelMa concentrations in resin, the study resulted in the amount of GelMa is directly proportional to cell variability. These results will help determine the concentration of PEGDa and GelMa that can be tested in future studies to ultimately print cells in 3D structures with high cell viability.

36 MATERIALS SCIENCE↗

Low Cost, High Volume, Carbon Fiber Precursor for Plasma Oxidation

Light weighting with carbon fiber is critical to improving the energy efficiency of wind turbines, airplanes, and automobiles, but the high cost of carbon fiber continues to limit market growth and applications. Half of this cost is in the raw materials. For the carbon fiber market to reach the next level of adoption, the cost of both the raw materials and conversion must be reduced. This project considered the combination of low-cost, textile-grade precursors combined with the increased efficiency of plasma oxidation to greatly reduce the cost of carbon fiber. The primary objective of this project was to make industrial-grade carbon fiber (550 ksi tensile strength, 35 Msi tensile modulus) from textile-grade PAN precursors, something that cannot be achieved with conventional oxidation and to date has not been achieved with any technology. To accomplish this, the project team iteratively optimized the process conditions in the plasma oxidation and carbonization stages to maximize the tensile properties of the resultant carbon fibers. This involved implementing experimental designs for both stages, whereby process conditions (e.g. temperature) were varied and correlated to fiber properties. Samples of oxidized PAN fibers (OPFs) were prepared using a small pilot-scale plasma oxidation oven at 4XTechnologies (4XT). The thermal, chemical, and physical properties of OPF samples were analyzed by the University of Tennessee (UTK) and Oak Ridge National Laboratory (ORNL). The OPF samples were then converted to carbon fiber by subsequent low- and high-temperature carbonization using a lab-scale furnace at ORNL. The resultant carbon fibers were tested for tensile strength also at ORNL, and the results were fed back into the experimental design. Of the hundreds of carbon fiber samples produced over the course of the project, the best sample had an average break strength of 479 ksi and modulus of 33 Msi. While the best tensile properties achieved fell short of the final project targets of 550 ksi for break strength and 35 Msi for modulus, the team demonstrated the potential to produce industrial-grade carbon fiber using textile-grade precursors. The best performing fiber samples had tensile properties that are 87% of the goal for tensile strength and 94% of the goal for tensile modulus. With additional optimization work, it is likely that the targets could be achieved, since only a fraction of the process parameter space was explored during this project. 4XT and its affiliate (4M) have already secured funding through private equity, and there is a CRADA (Cooperative Research and Development Agreement) project currently underway with the Carbon Fiber Technology Center (CFTF) at ORNL to continue this research. Additionally, while not an original goal of the project, the carbon fibers for most samples had diameters >8.5μm. This is considerably larger than commercially available carbon fiber products, which can impart unique properties to the composites (e.g. increased compressive strength) and decrease manufacturing costs even further. Moreover, these fibers were oxidized with plasma oxidation using residence times ranging <60mins, which would be considered fast for normal diameter fibers, but it is as much as 5x faster when factoring in the diameter of the fibers.

36 MATERIALS SCIENCE↗

Topaz, a Potential Volatile-Carrier in Cold Subduction Zone: Constraint from Synchrotron X-ray Diffraction and Raman Spectroscopy at High Temperature and High Pressure

The equation of state and stability of topaz at high-pressure/high-temperature conditions have been investigated by in situ synchrotron X-ray diffraction (XRD) and Raman spectroscopy in this study. No phase transition occurs on topaz over the experimental pressure–temperature ($P-T$) range. The pressure–volume data were fitted by the third-order Birch–Murnaghan equation of state (EoS) with the zero-pressure unit–cell volume V 0 = 343.86 (9) Å 3 , the zero-pressure bulk modulus K 0 = 172 (3) GPa, and its pressure derivative K’ 0 = 1.3 (4), while the obtained K 0 = 155 (2) GPa when fixed K’ 0 = 4. In the pressure range of 0–24.4 GPa, the vibration modes of in-plane bending OH-groups for topaz show non-linear changes with the increase in pressure, while the other vibration modes show linear changes. Moreover, the temperature–volume data were fitted by Fei’s thermal equation with the thermal expansion coefficient α 300 = 1.9 (1) × 10 –5 K –1 at 300 K. Finally, the $P-T$ stability of topaz was studied by a synchrotron-based single-crystal XRD at simultaneously high $P-T$ conditions up to ~10.9 GPa and 700 K, which shows that topaz may maintain a metastable state at depths above 370 km in the upper mantle along the coldest subducting slab geotherm. Thus, topaz may be a potential volatile-carrier in the cold subduction zone. It can carry hydrogen and fluorine elements into the deep upper mantle and further affect the geochemical behavior of the upper mantle.

36 MATERIALS SCIENCE↗

Derived parameters for NGC 6791 from high-metallicity isochrones

We have computed 8, 10, and 12 Gyr isochrones and physically consistent models of zero-age red horizontal branch stars for stellar masses between 0.55 and 1.3 solar mass, all at (fe/H) = +0.15. Comparison to the NGC 6791 BVI photometry of Kaluzny & Udalski (1992) and Montgomery et al. (1994) yields an age of 10.0 +/- 0.5 Gyr at an apparent distance modulus 13.49 less than (m-M)(sub V) less than 13.70. The color offsets required to fit the isochrones, combined with the spectroscopic results of Friel & Janes (1993), imply that the foreground reddening to NGC 6791 lies in the range 0.24 greater than E(B -V) greater than 0.19 with +0.27 less than (Fe/H) less than + 0.44. These results are derived using a technique by which we predict color shifts and apply these to the isochrones to simulate progressively higher metallicities. The zero-age horizontal branch model suggest that the red horizontal branch stars of NGC 6791 have masses approximately less than 0.7 solar mass. The masses are similar to those found for M67 red horizontal branch stars by Tripicco et al. (1993) and for globular cluster red horizontal branch stars, even though the M67 progenitors are approximately 0.2 solar-mass more massive, while the progenitors of globular cluster horizontal branch stars are similarly less massive. This suggests the presence of a mechanism, not strongly dependent on metallicity, which reduces stellar envelopes on the zero-age horizontal branch to a given mass rather than by a given amount.

Dorman, Ben↗